JL Audio Stealthbox SB-B-3SER/CPE/SDN(E9092), Stealthbox SB-B-3SER/CPE/SDN/13TW5, 94281 Installation Manual
I N S T A L L A T I O N G U I D E
for th e
SB-B-3SER/CPE/SDN(E90\92)
SKU#94281
2006-Up Sedan
2007-Up Coupe
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system. With proper
installation, your new vehicle-specific enclosed subwoofer system will deliver years of listening pleasure.
We strongly recommend that you have your new Stealthbox® installed by your authorized JL Audio
dealer. The installation professionals employed by your dealer have the necessary tools and experience
to disassemble and reassemble your vehicle properly. Also, keep in mind that your warranty coverage
extends to 2 years if your system is installed or approved by your authorized JL Audio dealer. If you
prefer to perform your own installation, please read this installation guide completely
before beginning the process.
If you choose to perform the installation yourself, it is absolutely vital that
the Stealthbox® be properly mounted to the vehicle according to these
instructions. Failure to mount the enclosure properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the enclosure
caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a collision
or sudden deceleration.
S T E P 1
Remove anything stored in the trunk so that you are working
in a clean environment.
Unpack the Stealthbox® and test for proper operation
before continuing!
The wiring for the Stealthbox® should go from the seam
between the seatback and the floor to the amplifier location.
Along the bottom of the rear deck from the trunk, there are
two recessed areas (as indicated by arrows at left) with two
bolts going up into the deck in each recess.
Continued on Next Page
S T E P 2
The outer-most bolt in each recess must be removed.
SB-B-3SER/CPE/SDN INSTR_SKU# 011256
INS TALLATIO N
D I F F I C U LT Y :
15
OU T
OF
EST IMATED TIME:
3 0 MIN
S T E P 3
Using each of the black oxide 3/8"-16 x 1 1/2" bolts assemble
a split lock washer, flat washer, bracket, 1" spacer, through the
hole in the bracket (the slot will mount the Stealthbox® to
the bracket).
SB-B-3SER/CPE/SDN INSTR_SKU# 011256
S T E P 5
Set the enclosure into the trunk with the woofers facing
down, attach the wires going to the amplifier. Push the
enclosure towards the seat, and tilt it up so that it rests fully
against the seat. Install the silver bolts, split lock washers
and flat washer through the slots in the previously installed
brackets into the Stealthbox®, apply pressure to the enclosure so that the bolts go through the slots as close to the
seat as possible and tighten all bolts.
C O N G R A T U L A T I O N S !
You have completed the installation for this model!
Enjoy your new Stealthbox®!
Please refer to the Power Recommendation section for an
amplifier recommendation and basic set-up help.
S T E P 4
Using the hardware assembled in STEP 3, install two mount
brackets where bolts were removed in STEP 2. Do not
tighten the bolts down yet, just get them snug. The slotted
end of the bracket should point down and towards the rear
of the car.
Page 2 • JL Audio, Inc 2008
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered
trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.
JLA-SKU# 011256 8-12-2008 • Printed in USA • ©2008 JL Audio, Inc. • U.S. PATENTS: #5,734,734 #5,949,898 #6,118,884 #6,229,902 #6,243,479
#6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign patents pending.
(954) 443-1100
ww w . j l a u d i o . co m
1 0 3 6 9 N O R T H C O M M E R C E P A R K W A Y • M I R A M A R , F L O R I D A • 3 3 0 2 5 • U S A
I N C L U D E D H A R D W A R E
(2) 8mm- 1.25 x 35mm Black Oxi de Hex Head Bolt
(2) 8mm- 1.25 x 22mm Chrome Hex Head B olt
(4) 8mm Flat Washer
(4) 8mm Split Lo ck Washer
(2) Custom Mount B rackets
(2) 3/4" Aluminium Spacer s
S P E C I F I C A T I O N S
Enclosure Type: Acoustic Suspension (sealed)
Driver Type: 13TW5-3
Nominal Imp edance: Dual 3 ohms
Continuous Power Handling: 600 Watts (per woofer)
P O W E R R E C O M M E N D A T I O N
JL Audio recommends using a high quality amplifiers such as the JL Audio HD750/1 or the 500/1v2. The diagram
below shows the recommended crossover, infrasonic filter and equalizer settings for the 500/1v2. when being used
to power your Stealthbox®.
The JL Audio 500/1v2 is a very versatile audio component. Please consult the owner’s manual for even more
detailed information about installing and tuning this amplifiers.
M I D / H I G H F R E Q U E N C Y D R I V E R F I T M E N T
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of your vehicle.
Front Speaker Si ze / Location: 4" In the doors
Fits JL Audi o Models: N/A
Rear Speaker Size / Location: Coupe-6.5"/Rear Deck Sedan-5.25"/rear doors....4" Rear Deck
Fits JL Audi o Models: TR650-CXi, TR650-CSi, VR650-CXi, TR650-CXi,TR650-CSi, VR650-CSi, C5-650, C5-650x,
ZR650-CSi (Coupe) TR525-CXi, TR525-CSi, VR525-CXi, TR525-CXi, TR525-CSi, VR525-CSi, C5-525, C5-525x,
ZR525-CSi......TR40 0-CXi (Sedan)
Towards back of
car >
+12VDC Ground Remote Preamp Output Section
Infrasonic Filter
“Q” Center Freq. Boost (dB)
Amp LP Filter
Advanced
Bass
Control
Amplifier Input Section
Subwoofer Output
MONO OUTP UT ON LY
Left Output Right Output Left Ch. Right Ch.Filter Freq. (Hz) Filter Freq. (Hz)Infrasonic Freq. (Hz) Remote Bass Port
Full Range | Amp Filter | Out Filter
Output Mode Filter Slope Mode
Mode | Slope
Input Voltage Input Sens. Signal Sensing
12dB| 24dB
Filter Mode
LP| HP
Bass EQ
Off | On
Off | 12dB | 24dB Low | High Off | OnOff | On
40
45
556580
100
200 15
18
223045
55
60 40
45
556580
100
200
0.5
0.7
1.1
1.6
2.7
4.3 20
25
304060
75
80 0
+4
+10
+13
+15
500/1v2
Monoblock Subwoofer Amplifier
Loading...