JL Audio Stealthbox, Stealthbox SB-H-FIT/10w3v3 Installation Manual

I N S T A L L A T I O N G U I D E

for th e

SB-H-FIT/10w3v3

SKU#94433

2007 plus

Thank you for choosing a JL Audio Stealthbox® for your automotive sound system. With proper

installation, your new vehicle-specific enclosed subwoofer system will deliver years of listening pleasure.

We strongly recommend that you have your new Stealthbox® installed by your authorized JL Audio

dealer. The installation professionals employed by your dealer have the necessary tools and experience

to disassemble and reassemble your vehicle properly. Please read this installation guide completely

before beginning the process.

If you choose to perform the installation yourself, it is absolutely vital that
the Stealthbox

®

be properly mounted to the vehicle according to these

instructions. Failure to mount the enclosure properly presents two problems:

1) The sub-bass performance will suffer due to the movement of the enclosure
caused by the force exerted by the woofer(s).

2) A loose enclosure presents a serious safety hazard in the event of a collision
or sudden deceleration.

S T E P 1

Place stealthbox in the trunk near its mounting location.
Take the supplied 3/8 - 16 x 1 1/2” Hex Head Bolt and
threaded into box leaving about 1/2” exposed.

Continued on Next Page

S T E P 2

Place wax square in the designated position. Place the box in
the proper position and press lightly, this will leave an imprint
on the wax square for proper drilling. Remove the 3/8-16 x 1
1/2” Hex Head Bolt from the Stealthbox®.

S T E P 3

Using a 3/8” drill bit, drill through the panel and the metal
fender well.

*CAUTION*

Before drilling, always make sure that you are not
going to be drilling into any gas lines, brake lines,
transmission lines, electrical wiring, exhaust systems
or anything else that might cause a reduction in
your weekly pay. Always wear eye protection when
drilling.

SB-H-FIT/10W3v3 INSTR_SKU# 011282

INS TALLATIO N
D I F F I C U LT Y :

25

OU T
OF

EST IMATED TIME:
12 HOU RS

SB-H-FIT/10W3v3 INSTR_SKU# 011282

S T E P 7

C O N G R A T U L A T I O N S !

You have completed the installation for this model!

Enjoy your new Stealthbox®!

Please refer to the Power Recommendation section for an
amplifier recommendation and basic set-up help.

S T E P 6

Place the box in its position and through the previously
drilled opening insert the supplied 3/8-16 x1 1/2” Hex Head
Bolt with the supplied Split Lock Washer closest to the head
of the 3/8-16 x 1 1/2” Bolt and then the 3/8 x 1 1/4” Fender
Washer closest to the fender well. Thread the 3/8-16 x 1 1/2”
Hex Head Bolt into the threaded insert in the Stealthbox®
(it may be helpful to have someone assist you in getting
everything aligned). Tighten the 3/8-16 x 1 1/2” Hex Head
Bolt.

S T E P 5

Connect the speaker wire to the box and run to the amp.
Test the stealthbox for proper operation at this time.

S T E P 4

This is what it should look like from the wheel well after
drilling through the panel and the metal fender well.

Page 2 • JL Audio, Inc 2010

All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered
trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.

JLA-SKU# 011282 ©11-11-2010 • Printed in USA • ©2010 JL Audio, Inc. • U.S. PATENTS: #5,734,734 #5,949,898 #6,118,884 #6,229,902
#6,243,479 #6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign
patents pending. For more detailed information please visit us online at www.jlaudio.com.

[phone]

ww w . j l a u d i o . co m

1 0 3 6 9 N O R T H C O M M E R C E P A R K W A Y • M I R A M A R , F L O R I D A • 3 3 0 2 5 • U S A

I N C L U D E D H A R D W A R E

1) 3” x 3” Wax Square

1) 3/8 - 16 x 1 1/2” Hex Head Bolt

1) 3/8 x 1 1/4” Fender Washer

1) 3/8” Split Lock Washe r

S P E C I F I C A T I O N S

Enclosure Type: Acous tic Suspension (sealed)
Driver Type: 10w3v3-2
Nominal Imp edance: 2 ohms
Continuous Power Handling: 500 watts

P O W E R R E C O M M E N D A T I O N

JL Audio recommends using a high quality amplifier such as the JL Audio 250/1v2.
The diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the 250/1v2
when being used to power your Stealthbox®.

The JL Audio 250/1v2 is a very versatile audio component. Please consult the owner’s manual for even more
detailed information about installing and tuning this amplifier.

M I D / H I G H F R E Q U E N C Y D R I V E R F I T M E N T

A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.

Front Speaker Si ze / Location: 6.5”- Front Doors
Fits JL Audi o Models: TR650-CXi, TR650-CSi, VR650-CXi, VR650-CSi, C5-650, C5-650x & ZR650-CSi

Rear Speaker Size / Location: 6.5”- Rear Door
Fits JL Audi o Models: TR650-CXi, TR650-CSi, VR650-CXi, VR650-CSi, C5-650, C5-650x & ZR650-CSi