JL Audio SB-VW-JETSW-10W3v3 User Manual

SB-VW-JETSW/10W3v3 INSTR_SKU# 94482
I N S T A L L A T I O N G U I D E
for the
SB- V W - J E TSW / 1 0 W3 v 3
SKU#94482
2009+
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system. With proper
We strongly recommend that you have your new Stealthbox® installed by your authorized JL Audio
dealer. The installation professionals employed by your dealer have the necessary tools and experience
to disassemble and reassemble your vehicle properly. Also, keep in mind that your warranty coverage
extends to 2 years if your system is installed or approved by your authorized JL Audio dealer. If you
prefer to perform your own installation, please read this installation guide completely
before beginning the process.
If you choose to perform the installation yourself, it is absolutely vital that the Stealthbox instructions. Failure to mount the enclosure properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the enclosure caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a collision or sudden deceleration.
®
be properly mounted to the vehicle according to these
S T E P 1
Empty out the trunk of the car so that you have a clean area to work in.
S T E P 2
Remove the cover for the spare, the spare tire and tool kit, the center post that secures the spare also needs to be removed.
S T E P 3
Pictured is all of the hardware included with the Stealthbox®.
INSTALLATION D I F F I C UL T Y:
OU T OF
25
ESTIMATED TIME: 1 HOUR
Continued on Next Page
SB-VW-JETSW/10W3v3 INSTR_SKU# 94482
S T E P 4
Take the three wax squares and put them on the floor where the spare had been in the approximate locations as shown.
S T E P 5
Install the three 3/8-16 x 2-1/4” Set Screws into the corresponding threaded inserts. In the picture to the left, they are shown with the included spacers already installed, this is not necessary yet, all that is needed at this time is the three 3/8-16 x 2-1/4” Set Screws. Note that the 1/2” tall spacer is on the 3/8-16 x 2-1/4” Set Screw to the left in the picture.
S T E P 6
Set the enclosure down into the spare tire well, keep it centered and towards the front of the well. wiggle the Stealthbox® so that it will make indentations in the Wax Squares as shown below, remove the Stealthbox® from the spare tire well.
S T E P 8
Using a 1/2” drill bit, drill through the three marks in the Wax Squares.
Before drilling, always make sure that you are not going to be drilling into any gas lines, brake lines,
tires, transmission lines, electrical wiring, exhaust
systems or anything else that might cause a
reduction in your weekly pay.
Always wear eye protection when drilling!
S T E P 9
Use strips of the Wax Squares, wrap them around the 3/8­16 x 2-1/4” Set Screws as shown to hold the spacers onto the 3/8-16 x 2-1/4” Set Screws during final installation of the Stealthbox®. Put the included Spacers on the 3/8-16 x 2-1/4” Set Screws in the order as shown in enclosure back into the spare tire well, the three 3/8-16 x 2-1/4” Set Screws should go down through the holes drilled
STEP 8.
in
S T E P 1 0
From underneath the car, install a 3/8 x 1-1/4” Fender Washer, 3/8” Split Lock Washer and 3/8-16 Hex Nut on each of the 3/8-16 x 2-1/4” Set Screws as they protrude through the floor.
Re-install the spare tire and floor panel that were removed
STEP 2.
in
STEP 5. Set the
Page 2 • JL Audio, Inc 2009
S T E P 7
The three 3/8-16 x 2-1/4” Set Screws should have made a mark in the wax squares as shown.
S T E P 1 1
C O N G R A T U L A T I O N S !
You have completed the installation for this model!
Enjoy your new Stealthbox®!
Please refer to the Power Recommendation section for an amplifier recommendation and basic set-up help.
Continued on Next Page
SB-VW-JETSW/10W3v3 INSTR_SKU# 94482
+12VDC Ground Remote Preamp Output Section
Infrasonic Filter
“Q” Center Freq. Boost (dB)
Amp LP Filter
Advanced Bass Control
Amplifier Input Section
Subwoofer Output
MONO OUT PUT O NLY
Left Output Right Output Left Ch. Right Ch.Filter Freq. (Hz) Filter Freq. (Hz)Infrasonic Freq. (Hz) Remote Bass Port
Full Range | Amp Filter | Out Filter
Output Mode Filter Slope Mode
Mode | Slope
Input Voltage Input Sens. Signal Sensing
12dB| 24dB
Filter Mode
LP| HP
Bass EQ
Off | On
Off | 12dB | 24dB Low | High Off | OnOff | On
40
45
556580
100
200 15
18
223045
55
60 40
45
556580
100
200
0.5
0.7
1.1
1.6
2.7
4.3
20
25
304060
75
80 0
+4
+10
+13
+15
500 /1v2
Monoblock Subwoofer Amplifier
I N C L U D E D H A R D W A R E
3) 3/8” Split Lock Washer 3) 3/8 x 1-1/4” Fender Washer
1) 1/2” x 1”OD Spacer 2) 1” x 1”OD Spacer
3) 3/8-16 x 2-1/4” Set Screw 3) 3/8-16 Hex Nut
S P E C I F I C A T I O N S
Enclosure Type: Acoustic Suspension (sealed) Driver Type: 10W3v3-4 Nominal Impedance: 4 Ohms Continuous Power Handling: 500Watts
P O W E R R E C O M M E N D A T I O N
JL Audio recommends high quality amplifiers such as the JL Audio HD900/5, 500/1v2 or J2 500.1. The diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the 500/1v2. If another amplifier is being used, please reference this illustration and use similar settings on that amplifier.
All JL Audio amplifiers are very versatile audio components. Please consult the owner’s manual for even more detailed information about installing and tuning your amplifier.
C O N N E C T I O N S
Page 3• JL Audio, Inc 2009
Using quality power, signal and speaker wire is essential in ensuring the performance of your Stealthbox®. JL Audio recommends using a 4 AWG power kit such as the XD-PCS4-1B for your Stealthbox® amplifier, other kits are available should you be using more than one amplifier. Signal wire such as the JL Audio Premium Audio Interconnect Cables should be used that will provide signal for both channels of the amplifier. JL Audio reccommends using 12AWG speaker wire for subwoofers such as our XD-BCS12-25.
M I D / H I G H F R E Q U E N C Y D R I V E R F I T M E N T
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.
Front Speaker Size / Location: 4”- Front Doors Fits JL Audio Models: TR400-CXi
Rear Speaker Size / Location: 6.5”- Rear Door Fits JL Audio Models: TR650-CXi, TR650-CSi, C2-650x, C2-650, C3-650,
C5-650, C5-650x & ZR650-CSi
(954) 443-1100
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.
JLA-SKU# 011308 06.21.2010 • Printed in USA • ©2010 JL Audio, Inc. • U.S. PATENTS: #5,734,734 #5,949,898 #6,118,884 #6,229,902 #6,243,479 #6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign patents pending. For more detailed information please visit us online at www.jlaudio.com.
1 0 3 6 9 N O R T H C O M M E R C E P A R K W A Y • M I R A M A R , F L O R I D A • 3 3 0 2 5 • U S A
w w w. j l a u d i o . c o m
Loading...