JL Audio SB-S-LWAG-10W6v2-TP, SB-S-LWAG-10W6v2-DG User Manual

SB-S-LWAG/10W6v2

2005 - Up

Subaru Legacy & Outback Wagon

(will not fit the sedans or the “Outback Sport”)

SB-S-LWAG/10W6v2_INSTR_SKU#011207

SB-S-LWAG/10W6v2_INSTR _SKU#011207

INSTALLATION GUIDE

for the

SB-S-LWAG/10W6v2

2005 - Up

(will not fit the sedans or the “Outback Sport”)

Thank you for choosing a JL Audio Stealthbox® for your automotive sound system. With proper

installation, your new vehicle-specific enclosed subwoofer system will deliver years of listening pleasure.

Subaru Legacy & Outback Wagon

If you choose to perform the installation yourself, it is absolutely vital that the Stealthbox instructions. Failure to mount the enclosure properly presents two problems:

1) The sub-bass performance will suffer due to the movement of the enclosure caused by the force exerted by the woofer(s).

2) A loose enclosure presents a serious safety hazard in the event of a collision or sudden deceleration.

be properly mounted to the vehicle according to these

STEP 1

Remove all contents from the cargo area.

STEP 2

Remove the passenger’s side rear pocket door and the separation wall.

INSTALLATION DIFFICULTY:

OUT OF

We strongly recommend that you have your new Stealthbox® installed by your authorized JL Audio

dealer. The installation professionals employed by your dealer have the necessary tools and experience

to disassemble and reassemble your vehicle properly. Also, keep in mind that your warranty coverage

extends to 1 year if your system is installed or approved by your authorized JL Audio dealer. If you

prefer to perform your own installation, please read this installation guide completely

before beginning the process.

STEP 3

With a small flat blade, carefully pop off the black plastic trim from the passenger’s side rear taillight.

Continued on Next Page

SB-S-LWAG/10W6v2_INSTR_SKU#011207

SB-S-LWAG/10W6v2_INSTR _SKU#011207

STEP 4

Remove the pair of screws that secure the passenger’s side rear taillight .

STEP 5

Remove the taillight assembly from the wiring harness.

Pull the wire harness out of the pass through hole.

STEP 6

Apply the supplied wax square into place. The left side is lined up with the left edge of the pocket opening and above the emboss portion of the inner lower corner.

STEP 8

Posi tion the Stealth box

in the mounting location and press

on it firmly.

Remove the Stealthbox

carefull y, le a v ing the wax squar es in place. The s ocket cup set sc rews w i l l leave im pres sions in the wax.

STEP 9

Note: Be fo re dr i ll in g , m ake s ure t h a t you a re no t go in g to be drilling into electrical wiring or anything else that might c au se a re d uc t io n i n you r wee k l y p ay. Alw ays wear eye protection when drilling!

From inside the vehi cle. Wit h a dril l and a 1/4-in c h dril l bit , dril l at the s ame ang le as the im pres s ion on the wax square. D rill t hrou g h the plast ic panel and me tal bo dy. Remove the wax square. Wit h a 3/8-inch d rill b it, e n larg e the pil o t h ole.

STEP 10

From t he outside o f the veh icle. Place the 3/8-inc h dril l bit th roug h the pass through h o le, enla rge th e p i lot hol e.

Page 2 • JL Audio, Inc 2006

STEP 7

Thr e ad the suppli e d socke t cup set s c rew int o the Stealthbox®, leavi n g 1 /4- i nch of th read expose d.

STEP 11

Run sp eaker wire f rom th e ampli fier location t o the Stealthbox

location.

Continued on Next Page

+ 1 hidden pages