(will not fit sport wagons)
SB-S-IMPRZA/10W6v2_INSTR_SKU#011218
SB-S-IMPRZA/10W6v2_INSTR _SKU#011218
INSTALLATION GUIDE
for the
SB-S-IMPRZA/10W6v2
2002 - Up
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system. With proper
installation, your new vehicle-specific enclosed subwoofer system will deliver years of listening pleasure.
We strongly recommend that you have your new Stealthbox® installed by your authorized JL Audio
dealer. The installation professionals employed by your dealer have the necessary tools and experience
to disassemble and reassemble your vehicle properly. Also, keep in mind that your warranty coverage
extends to 1 year if your system is installed or approved by your authorized JL Audio dealer. If you
prefer to perform your own installation, please read this installation guide completely
Subaru Impreza Sedans
(will not fit sport wagons)
before beginning the process.
If you choose to perform the installation yourself, it is absolutely vital that
the Stealthbox
instructions. Failure to mount the enclosure properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the enclosure
caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a collision
or sudden deceleration.
®
be properly mounted to the vehicle according to these
STEP 1
Remove the heavy carpet flooring from the trunk.
Flip over the thin underlying carpeting, as shown in the
picture at the right.
STEP 2
Locate and remove the round sticker that covers an exsisting
factory hole. The sticker will be painted the same color as the
exterior of the vehicle.
STEP 3
Enlarge this factory hole, using an Uni-bit® or 1/2-inch
drill bit.
INSTALLATION
DIFFICULTY:
OUT
OF
5
Note: Be for e dr i ll in g , ma ke su re t h at yo u ar e no t go in g
to be drilling into any gas lines, brake lines, transmission
lines, electrical wiring, transfer case (4x4 vehicles)
or anyt hi ng e l se t h at m ig h t c au se a re d uc t i on i n you r
weekly pay. Always wear eye protection when drilling!
Continued on Next Page
SB-S-IMPRZA/10W6v2_INSTR_SKU#011218
SB-S-IMPRZA/10W6v2_INSTR _SKU#011218
3/8-inch-16 x 2-1/4-inch Socket Cup Set Screw
3/8-inch x 2-inch Fender Washer
3/8-inch Split Lock washer
Acoustic Suspension (sealed)
*All speakers require spacers for installation
*All speakers require spacers for installation
STEALTHBOX WALL
SILCONE SEALANT
FLAT WASHER
LOCK WASHER
HEX NUT
THREADED INSERT
VEHICLE SHEET METAL
FENDER WASHER
SOCKET CUP SET SCREW
STEP 4
Flip t he thin car pet back into place. Feel for the hole enlarged
in STEP 3 and cut the thin carpe t at the hole.
Place t h e heav y car pet flooring back int o the trunk. Feel for
the hole enlarged in STEP 3 and cut the flooring at the ho le.
STEP 5
Place the Stealthbox® into the trunk. Run speaker wire
from the amplifier location to the Stealthbox® and attach
to the terminal.
Check the woofer for proper operation.
Thread in the supplied socket cup set screw into the bottom
of the Stealthbox®, leaving 1-1/2-inches exposed.
STEP 6
Carefully guide the socket cup set screw through the cuts
made in the carpeting and the enlarged hole.
From under the vehicle, apply supplied fender washer, flat
washer, lock washer and hex nut onto the exposed socket
cup set screw and secure.
Note: For add ed p ro te c t io n it i s re co mm e nd ed t h at
you appl y a be ad o f si li co ne b e t we e n t he ve hi c le a nd
the fen de r w a sh e r. Aft e r th e b ol t a ss e mb l y is t i gh t ly
secured, it is also recomme nded th at vehicle und ercoatin g m at e ri a l is a p pl ie d t o t he e x po se d a ss e mb l y.
CONGRATULATIONS
You have completed the installation for this model!
INCLUDED HARDWARE
(1)
3/8-inch-16 x 2-1/4-inch Socket Cup Set Screw
(1)
3/8-inch USS Flat Washer
(1)
3/8-inch x 2-inch Fender Washer
(1)
3/8-inch Split Lock washer
(1)
3/8-inch -16 Hex Nut
SPECIFICATIONS
Enclosure Type:
Driver Type:
Nominal Impedance:
Continuous Power Handling:
Acoustic Suspension (sealed)
10W6 v2-D 4
2 ohms mono
400 Watts
POWER RECOMENDATION
JL Audio recommends using a high quality amplifier such as the JL Audio A1400.
The diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the A1400 when
being used to power your Stealthbox®.
Input Voltage
Low | High
CH 1 (Left)
CH 2 (Right)
Pre-Outs
Power Protect
Bass Boost Controls
Remote
Bass Port
Bass Boost
Input Sens. LP Filter
Filter Freq. (Hz)
55
45
40
65
80
100
200
The JL Audio A1400 is a very versatile audio component. Please consult the owner’s manual for even more
detailed information about installing and tuning this amplifier.
MID/HIGH FREQUENCY DRIVER FITMENT
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.
Front Speaker Size / Location:
6.5-inch / Front Doors*
Fits JL Audio Models: TR, VR & XR650-CXi, TR,VR,XR,ZR650-CSi
*All speakers require spacers for installation
Rear Speaker Size / Location:
Fits JL Audio Models:
*All speakers require spacers for installation
6.5-inch / Rear Deck*
TR, VR & XR650-CXi
Page 3 • JL Audio, Inc 2006
Please refer to the Power Recommendation section for an
amplifier recommendation and basic set-up help.
(954) 443-1100
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered
trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.
JLA-SKU#011218-11-12-20066 • Printed in USA • ©2005 JL Audio, Inc. • U.S. PATENTS: #5,734,734 #5,949,898 #6,118,884 #6,229,902
#6,243,479 #6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign
patents pending. For more detailed information please visit us online at www.jlaudio.com.
10369 NORTH COMMERCE PARKWAY • MIRAMAR, FLORIDA • 33025 • USA
www.jlaudio.com