
2007 - Up Silverado, Sierra, Avalanche, Suburban, Tahoe, Yukon & Yukon XL
with Front Row 40/20/40 Split Bench Seating
SB-GM-SLVCTR2/10W3v3_INSTR_SKU#011248
SB-GM-SLVCTR2/10W3v3_INSTR_SKU#011248
INSTALLATION GUIDE
for the
SB-GM-SLVCTR2/10W3v3
2007 - Up Silverado, Sierra, Avalanche, Suburban, Tahoe, Yukon & Yukon XL
with Front Row 40/20/40 Split Bench Seating
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system. With proper
installation, your new vehicle-specific enclosed subwoofer system will deliver years of listening pleasure.
We strongly recommend that you have your new Stealthbox® installed by your authorized JL Audio
dealer. The installation professionals employed by your dealer have the necessary tools and experience
to disassemble and reassemble your vehicle properly. Also, keep in mind that your warranty coverage
extends to 2 years if your system is installed or approved by your authorized JL Audio dealer. If you
prefer to perform your own installation, please read this installation guide completely
before beginning the process.
If you choose to perform the installation yourself, it is absolutely vital that
the Stealthbox
instructions. Failure to mount the enclosure properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the enclosure
caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a collision
or sudden deceleration.
®
be properly mounted to the vehicle according to these
STEP 1
Remove any contents from the front seat area.
Flip the center seat back / storage bin in the up position.
STEP 2
Move both front seats all the way forward.
From the passenger side of the vehicle, look to the side of
the center seat back / storage bin.
Remove the black plastic push clip.
Remove the plastic trim.
STEP 3
From the driver’s side of the vehicle, look to the side of the
center seat back / storage bin.
INSTALLATION
DIFFICULTY:
OUT
OF
5
ESTIMATED TIME:
12 HOURS
Remove the bolt and plastic trim.
Continued on Next Page

SB-GM-SLVCTR2/10W3v3_INSTR_SKU#011248
SB-GM-SLVCTR2/10W3v3_INSTR_SKU#011248
STEP 4
From the driver’s side of the vehicle, look to the side of the
center seat back / storage bin.
Use an hex key to remove the black bolt that secures the
gray bracket to the center seat back / storage bin.
STEP 5
From the passenger’s side of the vehicle, look to the side of
the center seat back / storage bin.
Use an hex key to remove the black bolt that secures the
gray bracket to the center seat back / storage bin.
STEP 6
Grab a hold of the bottom cushion and pull forward.
Remove the bottom cushion from the vehicle.
STEP 8
Remove the four rear bolts that secure the seating to the
floor.
STEP 9
Remove the four front nuts that secure the seating to the
floor.
STEP 10
Run speaker wire from the amplifier location to the
Stealthbox® location.
Page 2 • JL Audio, Inc 2007
STEP 7
Remove the plastic tray from vehicle.
STEP 11
Slide the rear of the Stealthbox® into the mounting area first,
then drop the front of the Stealthbox® into place.
Continued on Next Page

SB-GM-SLVCTR2/10W3v3_INSTR_SKU#011248
SB-GM-SLVCTR2/10W3v3_INSTR_SKU#011248
3/8-inch -16 x 1-1/4-inch Hex Bolt
Acoustic Suspension (sealed)
P O W E R R E C O M M E N D A T I O N
TR650-CSi, TR650-CXi, VR650-CSi, VR650-CXi, XR650-CSi, XR650-CXi,
C5650, C5-650x & ZR650-CS
TR525-CXi, VR525-CSi, VR525-CXi, C5-525, C5-525x & ZR525-CS
STEP 12
Place the supplied lock washer and then flat washer onto the
supplied bolt.
Tilt the seating back.
From under the center seat section, place the bolt assembly
through a factory hole and into the threaded insert of the
Stealthbox®. This hole can be viewed in STEP 7, circled.
Secure the bolt assembly to the Stealthbox®, do not over
tighten.
STEP 13
We do not recommend the use of this center section to be
used as a seat. You can remove the seat belt latch as an extra
precaution.
STEP 14
Secure the bolts and nuts that were removed in
STEPs 8 & 9.
INCLUDED HARDWARE
(1)
3/8-inch -16 x 1-1/4-inch Hex Bolt
(1)
3/8-inch Lock Washer
(1)
3/8-inch Flat Washer
SPECIFICATIONS
Enclosure Type:
Driver Type:
Nominal Impedance:
Continuous Power Handling:
POWER RECOMMENDATION
Acoustic Suspension (sealed)
10W 3v3
4 ohms mono
300 Watts
JL Audio recommends using a high quality amplifier such as the JL Audio 250/1v2.
The diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the 250/1v2
when being used to power your Stealthbox®.
The JL Audio 250/1v2 is a very versatile audio component. Please consult the owner’s manual for even more
detailed information about installing and tuning this amplifier.
Page 3 • JL Audio, Inc 2007
Secure the plastic covers that were removed in STEPs 2 & 3.
CONGRATULATIONS
You have completed the installation for this model!
Please refer to the Power Recommendation section for an
amplifier recommendation and basic set-up help.
MID/HIGH FREQUENCY DRIVER FITMENT
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.
Front Speaker Size / Location:
Fits JL Audio Models:
C5650, C5-650x & ZR650-CSii
Rear Speaker Size / Location:
Fits JL Audio Models:
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered
trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.
JLA-SKU#011248-09-06-20077 • Printed in USA • ©2007 JL Audio, Inc. • U.S. PATENTS: #5,734,734 #5,949,898 #6,118,884 #6,229,902
#6,243,479 #6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign
patents pending. For more detailed information please visit us online at www.jlaudio.com.
10369 NORTH COMMERCE PARKWAY • MIRAMAR, FLORIDA • 33025 • USA
6.5-inch / Front Doors
TR650-CSi, TR650-CXi, VR650-CSi, VR650-CXi, XR650-CSi, XR650-CXi,
5.25-inch / Rear Door
TR525-CXi, VR525-CSi, VR525-CXi, C5-525, C5-525x & ZR525-CSii
(954) 443-1100
www.jlaudio.com