JL Audio SB-GM-CLDRO-10W3v3, SB-GM-CLRDO-10W3v3-GA, SB-GM-CLRDO-10W3v3-TN, SB-GM-CLRDO-10W3v3-DG, SB-GM-CLRDO-10W3v3 User Manual
...
➔
➔
➔
➔
Stealthbox
®
INSTALLATION GUIDE
SB-GM-CLDRO/10W3v3, JL AUDIO, Inc 2006
Sheet SKU#011189 Revision 3/8/2006Page 1
for the
SB-GM-CLRDO/10W3v3
(2004-Up Chevrolet Colorado & GMC
Canyon Crew Cab)
This Stealthbox is a product which
requires professional installation skills and
tools.
Please read this installation guide thoroughly before beginning the project. It
will guide you step by step through the
installation.Several of the steps in this
process may require two people to
accomplish.
It is absolutely vital that the enclosure
be properly mounted to the vehicle
according to these instructions. Failure
to mount the enclosure properly presents two problems: 1) The sub-bass
performance will suffer due to the
movement of the enclosure caused by
the force exerted by the woofer(s) and
2) A loose enclosure presents a serious
safety hazard in the event of a collision
or sudden deceleration.
Please enjoy your JL Audio Stealthbox
responsibly.
STEP 1:
With an 18mm deep socket,
remove the two front mounting nuts.
Also remove the jack out of the metal holder.
.
STEP 2:
There are two rear mounting nuts
that need to be removed. With a long extension and the 18mm deep socket.Remove the
rear mounting nuts.
STEP 3:
With the rear mounting nuts
removed,tilt the rear seat forward,off the
mounting studs.
STEP 4:
With the rear seat tilted forward,
locate the middle passenger’s shoulder safety
belt.Follow the belt down to the latch.With a
flat blade screw driver, push the red button.
This will disengage the shoulder belt.Pull the
belt through the crease of the seat and up to
the return pocket, located on the back wall.
STEP 5:
Remove the rear seat out of the
vehicle. You should use a second per son to
help out.
Also remove the metal jack holder.
*At this time run speaker wire from the
amplifier area to the Stealthbox area.Double
check the woofer for proper working order. *
STEP 6:
Place the middle of the supplied wax
square, in the middle of the mounting studs
and 3-3/4”from the point of the floor as it
star ts to elevate up. Remember to remove
the paper backing.
If the Stealthbox is mounted to far to the rear,
the rear seat will not fit.If the Stealthbox is
mounted to far forward,it will hit the front
center console.
START
HERE
Continued on Next Page ➔
www.jlaudio.com
➔
➔
➔
➔
X
3-3/4”
18-1/16”
36-1/8”
➔
➔
STEP 7:
(A) Thread the supplied socket cup
screw into the Stealthbox.Leave 1/2”exposed.
(B) Place the Stealthbox into position and line
up the curved cor ners of the Stealthbox,that
are between the woofer and the square shape
of the Stealthbox.These cor ners need to line
up with the curvature of the transmission
hump floor as it goes to the rear and jets to
the right and left of the truck. Once into place,
push down with force.
(C)With a 1/2” drill bit, drill at the impression that
was left by the Stealthbox in STEP6.
Cont.
From
Previous
Page
Continued on Next Page ➔
➔
STEP 8: With the drilled out hole in the floor.
Expose the socket cup set screw 2” out of the
Stealthbox.Place the Stealthbox into position and
guide the socket cup set screw through the drilled
hole.
From under the vehicle, place the supplied fender
washer, flat washer, lock washer and hex nut onto
the socket cup screw.
STEP 9: Place the jack back into the holder and
then place the jack assembly to the floor(same area
it was removed from) with the yellow knob facing
the passenger’s side rear door.With one factor y
mounting bolt. Secure the assembly with to the driver’s side mounting threads.Use the second factory
mounting bolt to plug up the passenger’s side
mounting threads.
STEP10: With a second person, place the rear
seat back into position.Wrap the shoulder belt in
front of the seat and through bottom crease of the
seat.
SB-GM-CLDRO/10W3v3, JL AUDIO, Inc 2006
Sheet SKU#011189 Revision 3/8/2006Pag e 2
www.jlaudio.com
*CAUTION*
Before drilling, make sure that you are not going to be
drilling into any gas lines, br ake lines, transmission lines,
electrical wiring, transfer case(4x4 vehicles) or anything
else that might cause a reduction in your weekly pay.
Always wear eye protection when drilling.
With the use of a 1/2” drill bit and dr ill. Drill out the
floor at the impression on the wax square.
After the hole is drilled, remove the wax square
➔
STEALTHBOX WALL
FENDER WASHER
FLAT WASHER
LOCK WASHER
THREADED INSERT
VEHICLE SHEET METAL
SOCKET CUP SET SCREW
HEX NUT
Loading...