JL Audio SB-GM-CFMINI-10W3v3, SB-GM-CFMINI-10W3v2 User Manual

➔

➔

➔

Stealthbox

®

INSTALLATION GUIDE

SB-GM-CFMINI/10W3v2, JL AUDIO, Inc 2004

Sheet SKU#011115 Revision8/2/2004 Page 1

for the

SB-GM-CFMINI/10w3v2

(1993-’02 Chevrolet Camaro &

Pontiac Firebird)

This Stealthbox is a product which
requires professional installation skills and
tools.
Please read this installation guide thor­oughly before beginning the project. It
will guide you step by step through the
installation. Several of the steps in this
process may require two people to
accomplish.

It is absolutely vital that the enclosure
be properly mounted to the vehicle
according to these instructions. Failure
to mount the enclosure properly pres­ents two problems: 1) The sub-bass
performance will suffer due to the
movement of the enclosure caused by
the force exerted by the woofer(s) and

2) A loose enclosure presents a serious
safety hazard in the event of a collision
or sudden deceleration.

Please enjoy your JL Audio Stealthbox
responsibly.

STEP 1:

Remove the driver’s side trim panel,

disconnect the speaker wires, if applicable.

STEP 2:

Remove the driver’s side carpet
from the cubby-hole in the corner of the
hatch. this piece of carpet will not be used in
the installation.Vehicle owner should keep this
carpet for possible future use, when removing
the Stealthbox.

STEP 3:

Insert the enclosure into the cubby­hole, taking care to loft and tuck the wiring
harness above the enclosure as you slide as
you slide it in. Push the enclosure firmly into
place

Make sure the enclosure is all the way
in!!!

STEP 4:

Using the supplied four self-tapping
screws. Seucre the enclosure’s moutning
bracket to the flooring of the vehcile.

Appling black paint to the tops of the screw
heads, just make this isntall that much more
speacial.

Important: Once the screws are thight­ened, spray under coating onto the
screw tips underneath the car to pre­vent rust and leaks. Failure to do so
may result in corrosion and could ore­sent a saftly hazard over time.

STEP 5:

Run speaker wires to the enclosure.

At this time, check the woofer for proper
operation.

START

HERE

Continued on Next Page ➔

www.jlaudio.com

➔

➔

Specifications:

Enclosure Type: Sealed
Driver Type: 10W3v2-D2
Nominal Impedance: 4Ω
Cont. Power Handling: 300Watts

JL Audio recommends using a high quality amplifier such as the JL Audio 250/1. The diagram below shows the recommended
crossover, infrasonic filter and equalizer settings for the 250/1 when being used to power your Stealthbox®.

Included Hardware:
(4) #10 x 5/8” pan head self tap

10369 N. Commerce Pkwy, Miramar, Florida 33025-392 Phone: [phone] Fax: [phone]

+12VDC Ground Remote

The JL Audio 250/1 is a very versatile audio component. Please consult the owner’s manual for detailed information
about installing and tuning this amplifier.

➔

STEP 8: Reconnect the factory speaker wires
and replace the driver’s side trim panel over the
enclosure.

➔

SB-GM-CFMINI/10W3v2, JL AUDIO, Inc 2004

Sheet SKU#011115 Revision8/2/2004 Pag e 2

www.jlaudio.com

Mid/High Frequency Driver Information:

CONGRATULATIONS!
INSTALL COMPLETE.

ZR650-CSi

XR650-CXi

Front Location Driver Size:

6.5”

Applicable JL Audio Products:

TR,VR,XR & ZR 650-CSi/CXi

Rear Location Driver Size:

6.5”

Applicable JL Audio Products:

TR,VR & XR650-CXi

Cont.
From

Previous

Page

Difficulty Of Installation:

Bass Control

Infrasonic Filter

Off/30Hz

+7

+3

+1

LF Boost (dB)

+10

+13

Amp LP Filter

Mode/Slope

Off/12dB/24dB

Filter Freq. (Hz)

Amplifier Input Section

Input Voltage

Input Sens.

Low/High

Left Ch.

Right Ch.

Signal Sensing

Off/On

JL AUDIO 250/1

monoblock subwoofer amplifier

Preamp Output Section

Output Mode

Full-Range/Low-Pass/High-Pass

Left Ch.

Right Ch.