Page 1
➔
➔
➔
➔
➔
Stealthbox
®
INSTALLATION GUIDE
SB-F-ZX3/10W3, JL AUDIO, Inc 2002
Sheet SKU#011157 Revision 06/18/02Page 1
(2000-Up ZX3 2-door & 2001-Up ZX5
4-door hatchback)
SB-F-ZX3/10W3
for the
This Stealthbox is a product that
requires professional installation skills
and tools.
Please read this installation guide
thoroughly before beginning the
project. It will guide you step by step
through the installation. Several of
the steps in this process may require
two people to accomplish.
It is absolutely vital that the
enclosure be properly mounted to
the vehicle according to these
instructions. Failure to mount the
enclosure properly presents two
problems: 1) The sub-bass
performance will suffer due to the
movement of the enclosure caused
by the force exerted by the
woofer(s) and 2) A loose enclosure
presents a serious safety hazard in
the event of a collision or sudden
deceleration.
Please enjoy your JL Audio
Stealthbox responsibly.
STEP 1:
Remove the four Phillips head
screws, panel button and cargo light from
driver’s side rear cargo area.
STEP 2:
Remove the plastic safety belt
retractor cover. Look up under the plastic
cover for a Phillips head screw. Remove this
screw. (The location of this screw is shown in
the picture by the upward arrow).
STEP 3:
Remove the two plastic Phillips head
screws indicated by the arrows.These are
located in the driver’s rear hatch plastic trim
panel. Remove the carpeted side panel.This
panel will be cut in Step 9 so as to form a
trim for the Stealthbox.The view shown
above is from the back seat looking toward
the hatch. Also remove the hatch flooring (this
flooring will be re-installed later).
STEP 4:
Locate the MOLEX®plug and pull it
loose from the side panel.
STEP 5:
Remove the T-27 TORX head bolt
from the back side of the driver’s side rear
wheel well. Remove the Phillips screw from
directly below the TORX head bolt.
STEP 6:
Loosen the driver’s side rear fabric
wheel well by pulling it toward the front of
the car.
.
START
HERE
Continued on Page 2 ➔
www.jlaudio.com
➔
➔
➔
➔
➔
➔
➔
➔
➔
➔
➔
➔
➔
Page 2
➔
➔
STEP 7:
Pull plastic mounting stud out from
the rear side metal panel were the MOLEX
®
wiring plug was removed in Step 4.
Cont.
From
Page 1
Continued on Page 3 ➔
➔
STEP 8:
Enlarge this hole to 1/2 in. (12.7 mm).
CAUTION: Always check for obstructions
before drilling.
ALWAYS WEAR EYE PROTECTION
WHEN DRILLING.
STEP 9:
Using a measuring tape and masking
tape, define the area to be cut as shown by
the picture (above) and dimensions (to the
right). All dimensions follow the contour of
the panel.
STEP 10:
After panel has been cut, it should
resemble this.
SB-F-ZX3/10W3, JL AUDIO, Inc 2002
Sheet SKU#011157 Revision 06/18/02Page 2
www.jlaudio.com
A
B
C
D
E
F
G
H
A) 2.5 in. (63.5mm) E) 1.25 in. (31.75mm)
B) 1.0 in. (25.4mm) F) 13.5 in. (342.9mm)
C) 11.0 in. (279.4mm) G) 9.375 in. (238.125mm)
D) 7.75 in. (196.85mm) H) 17.5 in. (444.5mm)
➔
Page 3
Specifications:
Enclosure Type: Acoustic Suspension (Sealed)
Driver Type: One JL AUDIO 10W3-D2 Subwoofer
Nominal Impedance: 4Ω
Cont. Power Handling: 250 Watts
JL Audio recommends using a high quality amplifier such as the JL Audio 250/1. The diagram below shows the recommended
crossover, infrasonic filter and equalizer settings for the 250/1 when being used to power your Stealthbox
®
.
Included Hardware:
(1) 3/8” Washer
(1) 3/8” Lock Washer
(1) 3/8” Hex nut
(1) 3/8” x 2 1/4” Socket Cup Set Screw
10369 N. Commerce Pkwy, Miramar, Florida 33025 Phone: 954.443.1100 Fax: 954.443.1111
JL AUDIO 250/1
monoblock subwoofer amplifier
Amplifier Input Section
Input Sens.
Input Voltage
Low/High
Left Ch.
Right Ch.
Signal Sensing
Off/On
Output Mode
Full-Range/Low-Pass/High-Pass
Left Ch.
Right Ch.
Amp LP Filter
Mode/Slope
Off/12dB/24dB
Filter Freq. (Hz)
Bass Control
LF Boost (dB)
Off/30Hz
Infrasonic Filter
+1
+13
+3
+7
+10
Preamp Output Section
+12VDC Ground Remote
The JL Audio 250/1 is a ver y versatile audio component. Please consult the owner’s manual for detailed information
about installing and tuning this amplifier.
➔➔
➔
Cont.
From
Page 3
➔
SB-F-ZX3/10W3, JL AUDIO, Inc 2002
Sheet SKU#011157 Revision 06/18/02Page 3
www.jlaudio.com
Mid/High Frequency Driver Information:
CONGRATULATIONS!
INSTALL COMPLETE.
TR570-CXi
Front Location Driver Size:
5"x7”
Applicable JL Audio Products:
TR570-CXi,
XR570-CXi or CSi
Rear Location Driver Size:
5"x7”
Applicable JL Audio Products:
TR570-CXi,
XR570-CXi or CSi
STEP 11: Reinstall the plastic side panel and
the 4 Phillips head screws, the safety belt
retractor cover and cargo light removed in
Steps 1 & 2. Place cut carpet side panel back
into car.
STEP 12:
Run speaker wire to the location of
the Stealthbox enclosure. At this time please
check for proper operation of woofer.
STEP 13: Slide Stealthbox enclosure into the
corner of cargo area. Insert the 3/8 in.
threaded mounting stud into the enclosure
and line it up with the 1/2 in. (12.7 mm) hole.
Slide through to outside of car. Make sure
relocated MOLEX
®
plug and wiring is not
going to be pinched by enclosure or side
panels.
STEP 14:
From outside of the car, slide hand
between the pulled fabric wheel well (Step
6) and the car’s body. Feel for the threaded
mounting stud.
STEP 15: Place fender washer, lock washer
and 3/8 in. nut onto threaded mounting stud.
Tighten firmly using a 9/16 in. deep socket.
STEP 16: After securely mounting the
Stealthbox, push fabric wheel well back into
place. Reinstall TORX head bolt and Phillips
head screw that was removed in Step 5.
STEP 17: Replace hatch carpet back into car.You
will need to tuck the carpet under the Stealthbox.
XR570-CXi
Loading...