SB-F-EXPEDEL/10W3v3
2007 - Up Ford Expedition EL (long wheel base)
SB-F-EXPED2/10W3v3_INSTR_SKU#011237
SB-F-EXPED2/10W3v3_INSTR_SKU#011237
2
12 H OURS
INSTALLATION GUIDE
for the
SB-F-EXPEDEL/10W3v3
2007 - Up Ford Expedition EL (long wheel base)
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system. With proper
installation, your new vehicle-specific enclosed subwoofer system will deliver years of listening pleasure.
If you choose to perform the installation yourself, it is absolutely vital that
the Stealthbox
instructions. Failure to mount the enclosure properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the enclosure
caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a collision
or sudden deceleration.
®
be properly mounted to the vehicle according to these
STEP 1
Collapse the third row seating.
Bring the lift tray to the up positions.
Remove the rear most storage cover.
STEP 2
Remove the front storage cover
INSTALLATION
DIFFICULTY:
OUT
OF
5
ESTIMATED TIME:
12 HOURS
We strongly recommend that you have your new Stealthbox® installed by your authorized JL Audio
dealer. The installation professionals employed by your dealer have the necessary tools and experience
to disassemble and reassemble your vehicle properly. Also, keep in mind that your warranty coverage
extends to 2 years if your system is installed or approved by your authorized JL Audio dealer. If you
prefer to perform your own installation, please read this installation guide completely
before beginning the process.
STEP 3
Remove the tailgate’s lower sill plate.
Continued on Next Page
SB-F-EXPED2/10W3v3_INSTR_SKU#011237
SB-F-EXPED2/10W3v3_INSTR_SKU#011237
STEP 4
With an 8mm socket, remove the bolts that secure the
plastic storage bins to the floor.
Remove the plastic storage bins from SUV.
STEP 5
With an 8mm socket, remove the pair of bolts that secure
the lift tray to the floor.
Remove the lift tray from SUV.
STEP 6
Remove the access door from the driver’s side rear
cargo panel.
STEP 8
With a T-50 torx socket, remove the bolt that secures the
driver’s side third row seat belt to the floor.
STEP 9
With a T-50 torx socket, remove the bolt that secures the
driver’s side third row seat belt to the ceiling.
Remove the sea t belt m o unt fr o m the ceil ing.
STEP 10
With a T-50 torx socket, remove the bolt that secures the
driver’s side second row seat belt to the floor.
Page 2 • JL Audio, Inc 2007
Unplug the power lift gate switch, from behind the side
panel.
STEP 7
Pop out the seat belt trim panel from the side panel.
STEP 11
With a T-50 torx socket, remove the bolt that secures the
driver’s side second row seat belt to the c-pillar.
Continued on Next Page
SB-F-EXPED2/10W3v3_INSTR_SKU#011237
SB-F-EXPED2/10W3v3_INSTR_SKU#011237
STEP 12
Pop out the circle cover that is located in the upper portion
of the c-pillar plastic cover.
With an 8mm socket, remove the bolt.
STEP 13
Remove the upper c-pillar plastic cover.
STEP 14
Remove the driver’s rear door sill plate.
STEP 16
With an 8mm socket, remove the bolt that secures the side
panel metal bracket to the floor.
STEP 17
Pull the rear portion of the side panel from location. Feed the
third row seat belt through the opening of the side panel.
STEP 18
Pull the front portion of the side panel from location. Feed
the second row seat belt through the opening of the side
panel.
Page 3 • JL Audio, Inc 2007
STEP 15
Remove the tailgate’s upper sill plate.
Remove the upper d-pillar plastic cover.
STEP 19
Remove the side panel from the SUV.
Continued on Next Page
SB-F-EXPED2/10W3v3_INSTR_SKU#011237
SB-F-EXPED2/10W3v3_INSTR_SKU#011237
STEP 20
Remove the plug from the factory amplifier.
STEP 21
With 10mm socket, remove the two nuts and one bolt that
secure the plastic woofer enclosure to the SUV.
STEP 22
Remove the woofer system from the SUV.
STEP 24
Use the last bolt assembly to secure the supplied
Z-bracket onto the bottom front of the Stealthbox®, as
pictured.
STEP 25
Place the Stealthbox® into the mounting area. Guide the two
factory studs through the two holes in the L-bracket.
Secure the top of the Stealthbox® using the factory nuts.
STEP 26
Secure the bottom of the Stealthbox® using the factory bolt.
Page 4 • JL Audio, Inc 2007
STEP 23
Place a supplied 3/8-inch lock washer then 3/8-inch flat
washer onto each supplied 3/8-inch bolt.
Use two of these bolt assemblies to secure the supplied
L-bracket to the top of the Stealthbox®.
STEP 27
Run speaker wire from the amplifier location to the
Stealthbox® location.
Double check the woofer for proper operation.
Continued on Next Page
SB-F-EXPED2/10W3v3_INSTR_SKU#011237
SB-F-EXPED2/10W3v3_INSTR_SKU#011237
STEP 28
From the back side of the removed side panel. Grind off the
plastic weld that holds the factory woofer grilles onto the
side panel. Remove the grille from the panel.
From the front side of the removed side panel. Place the
supplied wax squares into positions, as pictured.
STEP 29
Mount each supplied Phillips head screw into each corner of
the backside of the supplied grille, as pictured.
STEP 30
Position the grille assembly onto the wax squares, with the
screw heads up against the wax squares.
STEP 32
Remove the screws from the grille assembly. Place a supplied
#8 washer onto each screw.
To secure the grille onto the front side of the side panel. The
screws are to pass through from the back side of the side
panel into the back side of the grille.
Do not over tighten the screws.
Place the side panel back into the SUV.
STEP 33
Feed the second and third row seat belts back through the
side panel, from STEPs 17 & 18.
STEP 34
Reattach the wire harness to the power lift gate switch and
access door from STEP 6.
Page 5 • JL Audio, Inc 2007
Firmly press onto each corner of the grille.
Remove each grille assembly carefully, leaving the wax
squares in place. The head of the screws will leave an
impression on each wax square.
STEP 31
With a drill and a 1/8-inch drill bit, drill through the
impression made in each wax square and into the vehicle’s
side panel.
Remove the wax squares.
Secure the side panel metal bracket to the floor,
from STEP 16.
STEP 35
Place the cover back onto the c-pillar, from STEP 13.
Secure the bolt and replace the cover from STEP 12.
Secure the second row seat belt back onto the c-pillar and
floor from, STEPs 10 & 11.
Continued on Next Page
SB-F-EXPED2/10W3v3_INSTR_SKU#011237
SB-F-EXPED2/10W3v3_INSTR_SKU#011237
JLA-SKU#011237-08-08-200
(3)
3/8-inch -16 x 1-inch Hex Tap Bolt
(4)
3/8-inch Flat Washer
(1)
L-bracket
(4)
#8 SAE Flat Washer
(1)
Z-bracket
(4)
#8-32 x 1/2-inch Pan Head Screw
(3)
3/8-inch Split lock Washer
(1)
5/8-inch MDF Square Grille
Acoustic Suspension (sealed)
10W3v3
4 ohms mono
300 Watts
P O W E R R E C O M M E N D A T I O N
5-inch x 7-inch / Front Doors
TR570-CXi, XR570-CXi, XR570-CSi, C5-570x, C5-570, ZR570-CSi
5-inch x 7-inch / Rear Door
TR570-CXi, XR570-CXi, XR570-CSi, C5-570x, C5-570, ZR570-CSi
STEP 36
Secure the third row seat belt to the ceiling and floor,
from STEPS 8 & 9.
Snap in the seat belt trim panel, from STEP 7.
Replace the d-pillar cover, from STEP 16.
Replace the tailgate’s upper sill plate, from STEP 15.
Replace the driver’s rear door sill plate, from STEP 14.
STEP 37
Secure the lift tray to the floor, from STEP 5.
STEP 38
Replace the floor storage bins back into the SUV. Secure
them to the floor, from STEP 4.
INCLUDED HARDWARE
(3)
3/8-inch -16 x 1-inch Hex Tap Bolt
(1)
L-br a cket
(1)
Z-b rac ket
(3)
3/8-inch Split lock Washer
(4)
3/8-inch Flat Washer
(4)
#8 SAE Flat Washer
(4)
#8-32 x 1/2-inch Pan Head Screw
(1)
5/8-inch MDF Square Grille
SPECIFICATIONS
Enclosure Type:
Driver Type:
Nominal Impedance:
Continuous Power Handling:
POWER RECOMMENDATION
Acoustic Suspension (sealed)
10W 3v3
4 ohms mono
300 Watts
JL Audio recommends using a high quality amplifier such as the JL Audio 250/1v2.
The diagram below shows the recommended crossover, infrasonic filter and equalizer settings for the 250/1v2
when being used to power your Stealthbox®.
The JL Audio 250/1v2 is a very versatile audio component. Please consult the owner’s manual for even more
detailed information about installing and tuning this amplifier.
Page 6 • JL Audio, Inc 2007
Replace the tailgate’s lower sill plate back into the SUV,
from STEP 3.
Replace the storage covers back into the SUV,
from STEPS 1 & 2.
CONGRATULATIONS
You have completed the installation for this model!
Please refer to the Power Recommendation section for an
amplifier recommendation and basic set-up help.
MID/HIGH FREQUENCY DRIVER FITMENT
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.
Front Speaker Size / Location:
Fits JL Audio Models:
Rear Speaker Size / Location:
Fits JL Audio Models:
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered
trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.
JLA-SKU#011237-08-08-20077 • Printed in USA • ©2007 JL Audio, Inc. • U.S. PATENTS: #5,734,734 #5,949,898 #6,118,884 #6,229,902
#6,243,479 #6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign
patents pending. For more detailed information please visit us online at www.jlaudio.com.
10369 NORTH COMMERCE PARKWAY • MIRAMAR, FLORIDA • 33025 • USA
5-inch x 7-inch / Front Doors
TR570 -CXi, XR570 -CXi, XR570 -CSi, C5-570 x, C5-570, ZR570 -CSi
5-inch x 7-inch / Rear Door
TR570 -CXi, XR570 -CXi, XR570 -CSi, C5-570 x, C5-570, ZR570 -CSi
(954) 443-1100
www.jlaudio.com
Loading...