Jl audio SB-F-150-SPRCRW-13TW5V2 User Manual

SB-F-SPRCRW/13TW5v2 INSTR_SKU# 011297

If you choose to perform the installation yourself, it is absolutely
vital that the Stealthbox® be properly mounted to the vehicle
according to these instructions. Failure to mount the enclosure
properly presents two problems:

1) The sub-bass performance will suffer due to the movement of the
enclosure caused by the force exerted by the woofer(s).

2) A loose enclosure presents a serious safety hazard in the event of a
collision or sudden deceleration.

INSTALLATION

DI FFI CU LTY:

OUT

OF

5

2

ESTIMATED TIME:

12 HOURS

INSTALLATION GUIDE

for the

SB-F-150-SPRCRW/13TW5v2

SKU# 94460-94462

2009-Up Ford F-150 SuperCrew & 2017-Up Ford SuperDuty Crew Cab

Enclosure Type: Sealed
Driver Type: 13T W5v2
Nominal Impedance: 2 ohms
Continuous Power Handling: 600 watts (RMS method)

Thank you for choosing a JL Audio Stealthbox® for your automotive sound system.

With proper installation, your new vehicle-specific enclosed subwoofer system

will deliver years of listening pleasure.

We strongly recommend that you have your new Stealthbox® installed by your

authorized JL Audio dealer. The installation professionals employed by your

dealer have the necessary tools and experience to disassemble and reassemble

your vehicle properly. If you prefer to perform your own installation, please read

this installation guide completely before beginning the process.

Continued on Next Page

INCLUDED HARDWARE

BOM ID Qty SKU Description

- 2 151345 Wax Square (not shown)

SB-F-SPRCRW/13TW5v2 INSTR_SKU# 011297

1 2 151087 3/8 - 16 x 1-3/4” Hex Bolt
2 2 151095

3/8” Flat Washer
3 2 151126 3/8” Fender Washer
4 2 151081 3/8” Split Lock Washer
5 2 151406 3/8 - 16 Hex Nut
6 2 153865 Bracket
7 1 150570 Trim Panel
8 1 150295 #8 x 1” Self Tap Screw
9 4 150072 1/4 - 20 x 1-1/2” Hex Drive Bolt

Page 2 • JL Audio, Inc., 2017

Continued on Next Page

SB-F-SPRCRW/13TW5v2 INSTR_SKU# 011297

POWER RECOMMENDATION

JL Audio recommends high quality ampliers such as the JL Audio XD600/1v2. The diagram below shows the recommended crossover settings for the XD600/1v2. For a detailed description of the
amplier settings, consult the owner’s manual for the amplier. If another amplier is being used, please reference this illustration and use similar settings on that amplier.

CONNECTIONS

Using quality power, signal, and speaker wire is essential in ensuring the performance of your Stealthbox®. JL Audio recommends using a 4 AWG power kit such as the XD-PCS4-1B for your
Stealthbox® amplier. Other kits are available should you be using more than one amplier. Signal wire such as the JL Audio Premium Audio Interconnect Cables should be used to provide signal for
both channels of the amplier. JL Audio recommends using 12 AWG speaker wire for subwoofers such as our XC-BCS12-25.

Page 3 • JL Audio, Inc., 2017

Continued on Next Page

SB-F-SPRCRW/13TW5v2 INSTR_SKU# 011297

STEP 1

Empty the rear seat area.

STEP 2

Lift the rear seat.

STEP 3

Note: Steps 3-9 are for vehicles equipped with

the pictured plastic storage tray. For vehicles
without the tray, skip to Step 10.

STEP 5

Remove the two factory nuts from each side of
the tray.

STEP 6

Unscrew the wing nut securing the jack tools.

STEP 7

Remove the jack tools from the vehicle.

Fold open the plastic storage tray.

STEP 4

Remove the two cover panels from each side of
the tray to expose the factory nuts.

Page 4 • JL Audio, Inc., 2017 Continued on Next Page

STEP 8

Remove the plastic storage tray from the
vehicle.

SB-F-SPRCRW/13TW5v2 INSTR_SKU# 011297

STEP 9

Reinstall the factory nuts on the studs, and
fully tighten.

ST EP 10

Note: Steps 10-12 are for F-150 vehicles

equipped with the pictured factory subwoofer
enclosure only. For all other vehicles, skip to

Step 13.

ST E P 11

Unclip and remove the three bolt covers, and
remove the three bolts securing the factory
subwoofer enclosure.

STE P 13

Align a Bracket to each end of the Stealthbox®
as shown.

STE P 14

Thread a 1/4 - 20 x 1-1/2” Hex Drive Bolt
through each of the slots in the Bracket, into
the threaded inserts on the enclosure. With the
1/4 - 20 x 1-1/2” Hex Drive Bolts positioned at
the top of each slot, fully tighten both bolts.

Repeat the process for the opposite side.

ST E P 15

Place the Stealthbox® into the vehicle, as
shown.

STE P 12

Unplug and remove the enclosure from the
vehicle.

Page 5 • JL Audio, Inc., 2017 Continued on Next Page

ST E P 16

Align the Bracket with the raised edge of the
floor on the driver’s side, as shown.

Slide a Wax Square under each of the Brackets,
centering them with the forward hole in the
Bracket.

SB-F-SPRCRW/13TW5v2 INSTR_SKU# 011297

STEP 17

Carefully remove the Stealthbox® from the
vehicle without moving the two Wax Squares.

Remove the adhesive backing from each Wax
Square, and adhere them to the floor of the
vehicle.

ST E P 18

Carefully reinstall the Stealthbox®, and mark
the locations of each of the forward holes on
the Wax Squares using a pick tool or similar.

ST E P 19

Remove the Stealthbox® once more. Using a
3/8” drill bit, carefully drill through the carpet
and floor at each Wax Square mark made in the
previous step. Remove the Wax Squares.

ST EP 21

Align the forward hole in a Bracket with one
of the drilled holes in the floor, as shown. Slide
a 3/8” Flat Washer over a 3/8 - 16 x 1-3/4” Hex
Bolt, and slide the bolt through the forward
hole in the Bracket and the hole in the floor.

STEP 22

Repeat the process for the opposite side.

STEP 23

From under the vehicle, slide a 3/8” Fender
Washer, a 3/8” Split Lock Washer, and a 3/8 - 16
Hex Nut over each of the 3/8 - 16 x 1-3/4” Hex
Bolts, and fully tighten.

STEP 20

Remove the Bracket from each side of the
Stealthbox®.

Page 6 • JL Audio, Inc., 2017 Continued on Next Page

STEP 24

Reinstall the Stealthbox®. Reinstall the two 1/4

- 20 x 1-1/2” Hex Drive Bolts through the slots
in each Bracket, into the threaded holes in each
side of the enclosure, and fully tighten while
pressing down on the enclosure.

SB-F-SPRCRW/13TW5v2 INSTR_SKU# 011297

6.5-inch

C5-650, C7-650cw

STEP 25

Align the Trim Panel with the driver’s side of
the enclosure, as shown.

STEP 26

Lift the carpet flap to access the hole in the
Trim Panel. Using a 1/8” drill bit, drill through
the hole in the Trim Panel and into the
Stealthbox®.

Secure the Trim Panel with a #8 x 1” Self Tap
Screw, as shown.

STEP 27

Connect speaker cable to the terminal cup on
the side of the Stealthbox®, and route the cable
as necessary.

Replace the jack tools, if desired, and fold the
rear seats back down.

CONGRATULATIONS!

You have completed the installation for this model! Enjoy your new Stealthbox®!

MID/HIGH FREQUENCY DRIVER FITMENT

A variety of JL Audio coaxial and component systems will t in the factory speaker locations of your vehicle.

Vehicle

‘09-’14 F-150

‘15-Up F-150

&

‘17-Up

SuperDuty

Location /

OEM

Front Doors /

6 x 8-inch

Rear Doors /

6 x 8-inch

Front Doors /

6 x 9-inch

Rear Doors /

C1-570x, C2-570x, C5-570x C3-570, C5-570

C1-570x, C2-570x, C5-570x C3-570, C5-570

C1-690x, C1-690tx, C2-690tx,
C5-650x

C1-650x, C2-650x, C5-650x

Suggested JL Audio Speaker Models

Coaxial Models Component Models

(1)

C1-690, C3-650
C7-650cw

C1-650, C2-650, C3-650,

1 - Installat ion may require adaptor, 2 - Comp onent woofer only

(1,2)

(1)

, C5-650

(2)

(1)

,

Page 7 • JL Audio, Inc., 2017

®

[phone]

All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox®” and the Stealthbox logo, and “How we play®” are registered trademarks of JL Audio, Inc.
“Ahead of the Curve” and its respective logo are trademarks of JL Audio, Inc.

Printed in USA • ©2017 JL Audio, Inc. • For more detailed information please visit us online at www.jlaudio.com.

JLA-SKU# 011297 • ver. 03.22.2017 • 10369 NORTH COMMERCE PARKWAY • MIRAMAR, FLORIDA • 33025 • USA

www.jlaudio.com