
SB-D-DRNGO3 INSTR_SKU# 11329
INSTALLATION GUIDE
for the
SB-D-DRNGO3/13TW5
SKU#94529
2011 - Up
Thank you for choosing a JL Audio Stealthbox® for your automotive sound system.
With proper installation, your new vehicle-specific enclosed subwoofer system
will deliver years of listening pleasure.
If you choose to perform the installation yourself, it is absolutely vital that
the Stealthbox
instructions. Failure to mount the enclosure properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the enclosure
caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a collision
or sudden deceleration.
®
be properly mounted to the vehicle according to these
STEP 1
Empty out the cargo area so that you have a clean area to
work in.
STEP 2
Remove the floor panel from the vehicle, and open the jack
access door.
IN STALLAT ION
DIFFICULTY:
OUT
OF
2
ESTIMATED TIME:
1 HOU R
5
We strongly recommend that you have your new Stealthbox® installed by your authorized
JL Audio dealer. The installation professionals employed by your dealer have the necessary tools
and experience to disassemble and reassemble your vehicle properly. Also, keep in mind that your
warranty coverage extends to 2 years if your system is installed or approved by
your authorized JL Audio dealer. If you prefer to perform your own installation,
please read this installation guide completely before beginning the process.
STEP 3
Carefully pull up on the cargo sill panel to release the clips.
Unplug the harness and remove the panel from the vehicle.
Remove the sensor from the panel.
Continued on Next Page

SB-D-DRNGO3 INSTR_SKU# 11329
STEP 4
Remove the nut holding driver’s side of the cargo tub to the
vehicle.
STEP 5
Remove the nut holding the passenger side of the cargo tub
to the vehicle.
STEP 6
Remove the two nuts near the jack.
STEP 8
Remove the nut holding the rear of the factory sub enclosure
to the vehicle.
STEP 9
Remove the two nuts holding the front of the factory sub
enclosure to the vehicle. Unplug and remove the enclosure.
ST EP 10
Attach the Center Bracket to the seat bracket using the
factory nut as shown. Do not tighten at this time.
Page 2 • JL Audio, Inc., 2011
STEP 7
Remove the cargo tub from the vehicle and unclip the rear
seat extension panel. Reinstall the two nuts removed in the
previous step.
ST E P 11
Using a 1/4” -20 x 1” Bolt, a 1/4” Flat Washer, and a 1/4” Lock
Washer, attach the Left and Right Front Brackets to the
Stealthbox® as shown.
Continued on Next Page

SB-D-DRNGO3 INSTR_SKU# 11329
STE P 12
Connect speaker wire to the Stealthbox,® and place it into
the vehicle, aligning the Left and Right Front Brackets over
the factory studs, as shown. Thread the factory nuts onto
the studs. Be sure the harness unplugged in Step 3 is still
accessable.
STE P 13
Swing the Center Bracket around and align it with the
threaded insert in the enclosure. Using a 3/8” - 16 x 1-1/4”
Hex Bolt, a 3/8” Flat Washer, and a 3/8” Split Lock Washer,
attach the Center Bracket to the enclosure. Do not tighten
at this time.
STE P 14
Plug the sensor back in and secure it to the floor of the
vehicle using the double sided tape, as shown.
ST E P 16
Align the rear seat extension panel and the Front and Rear
Trim Brackets to the threaded inserts in the back of the
Stealthbox®. Using a 1/4” - 20 x 1” Bolt, a 1/4” Flat Washer, and
a 1/4” Lock Washer, attach the panel to the enclosure.
STEP 17
Using a straight edge, aligh the rear seat extension panel to
the top of the Stealthbox®, and firmly tighten the 1/4” - 20 x
1” Bolts. Tighten the 3/8” - 16 x 1-1/4” Hex Bolt holding the
Center Bracket to the enclosure, and tighten the factory nut
holding the Center Bracket to the vehicle.
ST E P 18
Pictured is the rear seat extension panel in place.
Page 3 • JL Audio, Inc., 2011
ST E P 15
Pictured is how the Front and Rear Trim Brackets will align
with the rear seat extension panel.
ST E P 19
Tighten the factory nuts holding the Left and Right Front
Brackets to the vehicle. Reinstall the cargo sill panel. Reinstall
the floor panel and cargo cover.
Continued on Next Page

SB-D-DRNGO3 INSTR_SKU# 11329
CONGRATU L ATION S!
You have completed the installation for this model!
Enjoy your new Stealthbox®!
Please refer to the Power Recommendation section for
an amplifier recommendation and basic set-up help.
INCLUDED HARDWARE
(1) Center Bracket (3) Front Trim Bracket (1) 3/8” Split Lock Washer (5) 1/4” Flat Washer
(1) Front Right Bracket (3) Rear Trim Bracket (1) 3/8” - 16 x 1-1/4” Hex Bolt (5) 1/4” Lock Washer
(1) Front Left Bracket (1) 3/8” Flat Washer (5) 1/4” - 20 x 1” Bolt
SPECIFICATIONS
Enclosure Type: Acoustic Suspension (sealed)
Driver Type: 13TW5
Nominal Impedance: 3 ohm
Continuous Power Handling: 600 watts
POWER RECOMMENDATION
JL Audio recommends high quality ampliers such as the JL Audio HD900/5, 500/1v2 or XD600/1.
The diagram below shows the recommended crossover settings for the XD600/1. If another amplier is being
used, please reference this illustration and use similar settings on that amplier.
All JL Audio ampliers are very versatile audio components. Please consult the owner’s manual for even more
detailed information about installing and tuning your amplier.
CONNECTIONS
Using quality power, signal, and speaker wire is essential in ensuring the performance of your Stealthbox®.
JL Audio recommends using a 4 AWG power kit such as the XD-PCS4-1B for your Stealthbox® amplier. Other
kits are available should you be using more than one amplier. Signal wire such as the JL Audio Premium
Audio Interconnect Cables should be used that will provide signal for both channels of the amplier. JL Audio
reccommends using 12AWG speaker wire for subwoofers such as our XC-BCS12-25.
Page 4• JL Audio, Inc., 2011
MID/HIGH FREQUENCY DRIVER FITMENT
A variety of JL Audio coaxial and component systems will t in the factory speaker locations of you vehicle.
Front Speaker Size / Location: 6 x 9”- Front Doors
Fits JL Audio Models: TR690-TXi, C2-690tx
Rear Speaker Size / Location: 6-1/2”- Rear Door
Fits JL Audio Models: TR650-CXi, C2-650x, C2-650, C3-650,
C5-650x, C5- 650, ZR650-CSi
(954) 443-1100
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered
trademarks of JL Audio, Inc.,. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.,.
JLA-SKU# 94529 12.01.2011 • Printed in USA • ©2011 JL Audio, Inc.,. • U.S. PATENTS: #5,734,734 #5,949,898 #6,118,884 #6,229,902 #6,243,479
#6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign patents pending.
For more detailed information please visit us online at www.jlaudio.com.
10369 NORTH COMMERCE PARKWAY • MIRAMAR, FLORIDA • 33025 • USA
www.jlaudio.com