If you choose to perform the installation yourself, it is absolutely
vital that the Stealthbox® be properly mounted to the vehicle
according to these instructions. Failure to mount the enclosure
properly presents two problems:
1) The sub-bass performance will suffer due to the movement of the
enclosure caused by the force exerted by the woofer(s).
2) A loose enclosure presents a serious safety hazard in the event of a
collision or sudden deceleration.
JL Audio recommends high quality ampliers such as the JL Audio XD600/1v2. The diagram below shows the recommended crossover settings for the XD600/1v2. For a detailed description of the
amplier settings, consult the owner’s manual for the amplier. If another amplier is being used, please reference this illustration and use similar settings on that amplier.
CONNECTIONS
Using quality power, signal, and speaker wire is essential in ensuring the performance of your Stealthbox®. JL Audio recommends using a 4 AWG power kit such as the XD-PCS4-1B for your
Stealthbox® amplier. Other kits are available should you be using more than one amplier. Signal wire such as the JL Audio Premium Audio Interconnect Cables should be used to provide signal for
both channels of the amplier. JL Audio recommends using 12 AWG speaker wire for subwoofers such as our XC-BCS12-25.
Page 3 • JL Audio, Inc., 2019
Continued on Next Page
Page 4
SB-D-5GRAMCCF/12TW3 INSTR_SKU# 011530
STEP 1
Empty the rear seat area.
STEP 2
Fold the seat bottoms up.
STEP 3
Locate the two inner seat bracket bolts.
STEP 5
Place the enclosure on a flat surface with the
woofers facing upward. Align the four slots in
the Bracket with the threaded inserts on the
back of the enclosure, as shown.
Slide a 3/8” Split Lock Washer and a 3/8” Flat
Washer over each of two 3/8 - 16 x 1-1/4” Hex
Head Bolts, pass an assembly through each of
slots in the Bracket, into the threaded inserts,
and hand tighten.
STEP 6
Place the Stealthbox® into the vehicle. Center
the enclosure, and align the two upper slots in
the Bracket with the factory inner seat bracket
bolt holes.
STEP 7
While holding the Bracket in its position,
carefully lift the enclosure, then fully tighten
the four 3/8 - 16 x 1-1/4” Hex Head Bolts.
STEP 4
Using an E12 socket and wrench, remove the
two inner seat bracket bolts.
Page 4 • JL Audio, Inc., 2019Continued on Next Page
STEP 8
Connect speaker cable to the terminal cup on
the back of the enclosure, and lower the
enclosure back into position. Reinstall the two
factory inner seat bracket bolts, and fully
tighten.
Route the speaker cable as necessary.
Page 5
6 x 9-inch
C2-650x
, C5-650x
C3-650
, C5-650
, C7-650cw
SB-D-5GRAMCCF/12TW3 INSTR_SKU# 011530
STEP 9
Fold the seat bottoms back down.
CONGRATU LATION S!
You have completed the installation for this model! Enjoy your new Stealthbox®!
Page 5 • JL Audio, Inc., 2019
MID/HIGH FREQUENCY DRIVER FITMENT
A variety of JL Audio coaxial and component systems will t in the factor y speaker locations of your vehicle.
Location / OEM
Speaker Size
Front Dash /
3-1/2-inch
Front Doors /
6 x 9-inch
Rear Doors /
All specifications are subject to change without notice. “JL Audio®” and “How we play®” are registered trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo are trademarks
of JL Audio, Inc.