JL Audio MV600/1 Connection Guide

600W Monoblock Class D
Marine Subwoofer Amplier
Thank you for purchasing a JL Audio amplifier for your marine sound system.
Your amplifier has been designed and manufactured to exacting standards in order to ensure years of musical enjoyment in your vessel. For maximum performance, we highly recommend that you have your new amplifier installed by an authorized JL Audio dealer. Your authorized dealer has the training, expertise and installation equipment to ensure optimum performance from this product. Should you decide to install the amplifier yourself, please take the time to read this manual thoroughly to familiarize yourself with its installation requirements and setup procedures.
If you have any questions regarding the instructions in this manual or any aspect of your amplifier’s operation, please contact your authorized JL Audio dealer for assistance. If you need further assistance, please contact the JL Audio Technical Support Department at technical@jlaudio.com/support.
Installation Applications
This amplifier is designed for operation with 12 volt DC, negative-ground electrical systems. Using this product in vessels with positive ground and/or voltages other than 12V DC may result in damage to the product and will void the warranty. This product is not certified or approved for use in aircraft.
Planning Your Installation
It is important that you take the time to read this manual thoroughly and that you plan your installation carefully. It is very easy to damage electrical systems in modern vessels. Never assume that you have found appropriate wires without consulting a reliable wiring diagram or without analyzing using proper test equipment. If you are uncomfortable or unfamiliar with diagrams or testing methods, please enlist the services of your authorized JL Audio dealer to perform the installation. Your authorized dealer has the training, expertise and installation equipment to ensure optimum performance from this product. your installation.
The following are some considerations that you must take into account when planning
Product Description
The MV600/1 is a monoblock, Class D marine subwoofer amplifier equipped with NexD2™, the second generation of JL Audio’s high-speed switching technology. It is engineered to deliver reference-grade, low-frequency amplification with outstanding efficiency. This amplifier is configured using an external device (PC, Tablet or Phone), with the appropriate JL Audio TüN™ application installed. (See What is TüN? section for more info.)
What is Included
(1) Amplifier (4) Mounting Screws (1) Power Connector (1) 2.5 mm Hex Wrench (1) Subwoofer Output Harness (1) 3 mm Hex Wrench (1) USB A/B Cable (6 ft./1.8 m) (1) Connection Guide
Cooling Efficiency Considerations
The outer shell of your JL Audio amplifier is designed to remove heat from the amplifier circuitry. For optimum cooling performance, this outer shell should be exposed to as large a volume of air as possible. Enclosing the amplifier in a small, poorly ventilated chamber can lead to excessive heat build-up and degraded performance. If an installation calls for an enclosure around the amplifier, we recommend that this enclosure be ventilated with the aid of a fan. In normal applications, fan-cooling is not necessary. When mounting the amplifier in an enclosed compartment, make sure there is at least 1 inch (2.5 cm) of space above the amplifier’s outer shell to permit proper cooling.
3.67 in 93 mm
2.05 in
52 mm
with
CONNECTION GUIDE
10.59 in 269 mm
5 6 7
11.20 in 285 mm
6.93 in
176 mm
Safety Considerations
• Install your amplifier in a dry, well-ventilated location that does not interfere with factory installed systems.
• This product should never be submerged under water or subjected to high-pressure water spray.
• Do not install where it will be directly exposed to the elements, or in the engine compartment, or in any areas of extreme heat. Areas exposed to a heater or hot air should also be avoided.
• When selecting a mounting location, consider the orientation of the amplifier and its associated connections. If possible, position the amplifier vertically, with all connections pointing downward. Wiring and cables should be routed to direct potential condensation and moisture away from the amplifier.
• Securely mount the amplifier so that it does not come loose in the event of a collision or sudden jolt, or as a result of repeated vibrations during normal operation.
• Check before drilling to make sure that you will not be drilling into an exterior panel/hull, fuel tank, fuel line, wiring harness, or other vital system.
• Do not run system wiring outside or underneath the vessel. This is an extremely dangerous practice, which can result in severe damage/injury.
• Protect all system wires from sharp edges by carefully routing them, tying them down and using grommets and loom, where appropriate.
• Secure all wiring as needed, using cable ties or wire clamps to protect them from moving parts and sharp edges.
Power Connector
1
The MV600/1’s “+12 VDC” and “Ground” connections are designed to accept up to 4 AWG copper wire. Note: Copper Clad Aluminum (CCA) wire is not recommended. Tinned copper power wire is the best choice for marine installations. 4 AWG is the
minimum copper wire size for this amplifier.
To connect the power, ground and remote turn-on wires to the amplifier, back out the set screws on the connector using the supplied hex wrenches. Strip back 3/8 inch (10 mm) of insulation from the end of each wire and insert the bare wire into the receptacle on the power connector plug, seating it firmly so that no bare wire is exposed. While holding each wire in place, tighten each set screw firmly, taking care not to strip the head of the screw. Install the power connector by
plugging it into the amplifier’s power connector receptacle, pushing firmly.
A. +12 VDC: Run copper wire from the positive (+12V) battery post to the amplifier mounting location. If additional
amplifiers are being installed, run the appropriate gauge copper wire for the combined, maximum current draw, and install a fused distribution block near the amplifiers.
B. An appropriate fuse or ignition-protected circuit breaker (sold separately) at the main power wire(s) is vital for vessel
safety. This must be installed within 7 inches (18 cm) of the battery post connection or in compliance with marine industry standards. If this is the only device connected to this main wire, use a 50 A value. Do not install the fuse or close the circuit breaker until the power wire has been securely connected to the amplifier and all other connections have been made.
C. Ground: This connection should be made to the NEGATIVE battery post. Alternatively, an appropriately equipped and
positioned DC ground bus bar near the battery may be used. All ground connections (source unit and amplifiers)
should be made at the same location.
D. Remote: This connection should be made to the source unit’s positive (+12V) remote turn-on output. If your source
unit does not have a dedicated remote turn-on output, the amplifier’s remote turn-on connection can be connected to +12V via a switch that derives power from an ignition-switched circuit.
Input Section
2
Two female RCA jacks feed a differential-balanced input section, providing a high degree of input flexibility, and retaining superior noise rejection. This type of input architecture also allows the MV600/1 to cleanly accept any analog audio signal
up to 8 VRMS, without using a line-output converter.
Pre-Outs
3
Two female, RCA jacks deliver line-level, analog audio outputs (Max 4 V RMS) that are compatible with most types of aftermarket equipment.
Mounting Considerations
MV amplifiers are equipped with keyhole style mounting holes to simplify installations in confined spaces or vertical-mount applications. Mounting screws may be preinstalled, allowing amplifier connections to be made prior to securing in its final location. See diagram at right.
When selecting the installation location, consider the mounting orientation of the amplifier and its associated connections. If possible, position the amplifier vertically, with all connections pointing downward. Wiring and cables should be routed to direct potential condensation and moisture away from the amplifier. When installed in this manner, the amplifier achieves an IPX2 water-resistance rating.
Speaker Output Harnesses
4
Connect the speaker output leads to the corresponding speaker wires. The harness and companion cable are equipped with water-resistant connectors for maximum connection integrity in marine environments.
JLid-COMM
5
Connect optional accessories (MVi-HUB, M-DRC-50, VXi-BTC, etc.) to this port.
USB
6
This USB A/B port permits connection to a computer for configuration and tuning, using TüN™ Software.
7
Use a small pin to perform the following:
Reset Buttons
(A) Factory Reset (wipe memory, reboot amp) - Press and hold the button for 7 seconds. All user settings will be
erased and the amplifier will revert to its factory settings!
(B) Reboot Amplifier - Press and release the button. Previous user settings will be retained.
LED Status/Condition Reporting
LEDs located on the chassis top and connection panel are used to communicate amplier status and condition. Refer to the table below for the location and meaning for each behavior.
LED / Location Behavior Status/Condition›
Flashing Blue Critical Voltage (too low)
LED / Amplier Top
Upper Left LED / JLid-COMM Port
Upper Right LED / JLid-COMM Port
Flashing Red Critical Temperature (too hot)
Flashing Yellow Excessive Output Current (low impedance/short)
Green Detecting JLid™ Device
Blue JLid™ Connection Success
Yellow Invalid JLid™ Device
Flashing Red Excessive Current on JLid Port
Flashing Red
Green Active Connection with TüN™ Software
Critical Voltage/Temperature
Excessive Remote Output Current
Wiring Diagram - MV600/1
+12 VDC - Positive (+12V) Battery Connection
Ground - Negative (–) Ground Connection
Remote - Positive (+12V) Turn-On Input From Source Unit
ANALOG
INPUTS
CH. 1 - Ch. 1 Signal Input CH. 2 - Ch. 2 Signal Input
JLid-COMM - Optional Digital Remote Controller, Network Hub or
Bluetooth® Communicator Connection (Sold Separately)
Standard CAT5 Network Cable
Attached to Amp
Included
Not Included
SUB - To Subwoofer(s): (+ and –)
What is TüN?
TüN™ is software that you use to setup your MV amplifier, as well as tune and configure MVi amplifiers, and other JL Audio DSP products. TüN™ automatically recognizes what it is connected to, and allows you to make adjustments with a clear interface specifically set up for that product. TüN™ is available for download for free in a variety of applications, for computers and most handheld devices. For more information, visit: jlaudio.com/tun
For Windows® PC or Mac® computers, TüN™ connects via USB and offers complete control and command of the entire MV and MVi feature set from the comfor t of your desk or driver’s seat. Software also runs in demo mode, without connected amplifiers, for offline setup or demo purposes. Test drive it for free!
To Computer with TüN™ software installed
USB A/B Cable -
Connections
Power Connector
Connection Wire Capacity Description
+12 VDC (+) 4 AWG Positive (+12V) Battery Connection
Ground (–) 4 AWG Negative (GND) Battery Connection
Remote 18 to 10 AWG Positive (+12V) Remote Turn-On Input from Source Unit
Input Section
Label RCA Jack Description
CH. 1 Black RCA Channel 1 Signal Input
CH. 2 Red RCA Channel 2 Signal Input
Pre-Outs (pass-through)
Label RCA Jack Description
P. 1 Black RC A Preamp Signal Output 1
P. 2 Red RCA Preamp Signal Output 2
Connections
Label Wire Color Description
SUB
Label Type Description/Use
JLid-COMM RJ45 Jack Optional accessory connections (MVi-HUB, VXi-BTC, etc)
USB USB A/B Port Computer connection to congure TüN™ Software Interface
Reset
Brown (+) Positive Subwoofer Output
Brown/White (–) Negative Subwoofer Output
Button - A
Button - B Reboot Amp - Press and release.
Speaker Outputs
Data Connections
Factory Reset (wipe memory, reboot amp) - Press and hold
for 7 seconds.
P. 2 - Preamp Signal Output 2 P. 1 - Preamp Signal Output 1
Specifications
Amplier Specications
Amplier Topology 2nd-Gen NexD™ High Speed Class D
Power Supply Type Unregulated MOSFET Switching
Operating Voltage 10 - 15V DC
Min. Copper Power/GND Wire 4 AWG
Recommended Fuse 50 A
Standby Current Draw 3.6 mA
Rated RMS Power @ 14.4V,
Rated RMS Power @ 12.5V,
Inputs/Outputs
Analog Inputs
Analog
Outputs
Dimensions
<1% THD+N
<1% THD+N
Frequency Response 12 Hz - 500 Hz (+0, -1dB)
Damping Factor >125 / 50 Hz @ 4 Ω, >125 / 50 Hz @ 2 Ω
IP Rating
Type Line-Level, Dierential-Balanced
Number of Channels 2, via chassis-mounted female RCA jacks
Input Voltage Range 250 mV - 8 V RMS
S/N Ratio,
(A-weig hted, 20 kHz
noise bandwidth)
Type 2 Line-Level, via chassis-mounted female RCA jacks
Max Output Level 4 V RMS
L x W x H 11.20 in x 6.93 in x 2.05 in / 285 mm x 176 mm x 52 mm
ANALOG PREAMP OUTPUTS
400W x 1
@ 4 Ω
300W x 1
@ 4 Ω
IPX2 (when mounted vertically with connections pointed downward)
90 dB (Referred to rated power), 64 dB (Referred to 1 W)
500W x 1
@ 3 Ω
400W x 1
@ 3 Ω
600W x 1
@ 2 Ω
500W x 1
@ 2 Ω
For iPad or Android tablets. Enjoy the TüN™ software experience on your tablet, with the freedom of a wireless connection via Bluetooth®. Requires VXi-BTC Bluetooth® Communicator.
Wireless connection and streamlined options, for fast and simple amplifier setup. Download TüN™ Express for iPhone, iPad and Android phones & tablets. Requires VXi-BTC Bluetooth® Communicator.
Limited Warranty – Marine Amplifiers (USA)
JL Audio warrants this product to be free of defects in materials and workmanship for a period of two (2) years from the original date of purchase. This warranty is not transferable and applies only to the original purchaser from an authorized JL Audio dealer. Should service be necessary under this warranty for any reason due to manufac turing defect o r malfunction, J L Audio will (at its discreti on), repair or replace the d efective produc t with new or remanufactured product at no charge. Damage caused by the following is not covered under warranty: accident, m isuse, abuse, produc t modificatio n or neglect, fa ilure to follow install ation instructi ons, unauthorized repair attempts, misrepresentations by the seller. This warranty does not cover incidental or consequential damages and does not cover the cost of removing or reinstalling the unit(s). Cosmetic damage due to accident or normal wear and tear is not covered under warrant y.
Products installed as original equipment by boat manufacturers are covered by the boat manufacturer’s warranty, not JL Audio, Inc.
Warranty is void if the product’s serial number has b een removed or defaced.
Any applicable implied warranties are limited in duration to the period of the express warranty as provided herein beginning with the date of the original purchase at retail, and no warranties, whether express or implied, shall apply to this product thereafter. Some states do not allow limitations on implied warranties, therefore these exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state.
If you need service on your JL AUDIO product:
All warrant y returns should b e sent to JL Audio ’s Amplifi er Service Facilit y freight-prepaid t hrough an authorize d JL Audio dealer and must be accompanied by proof of purchase (a copy of the original sales receipt). Direc t returns fr om consumers or non -authorized deal ers will be refuse d unless specifi cally authorized by J L Audio with a valid retu rn authorization n umber. Warranty expir ation on product s returned withou t proof of purchase wil l be determin ed from the manufac turing date code. Coverage may be invalidated as this date is previou s to purchase date. Non- defective items received w ill be returned fre ight-collect. Cus tomer is responsible f or shipping charges and insurance in sending the produc t to JL Audio. Freight damage on returns is not covered under warranty.
For Service Information in the U.S.A. please call
JL Audio Customer Service:
(954) 443-1100 9:00 AM – 5:30 PM (Eastern Time Zone)
JL Audio, Inc.
10369 North Commerce Pkwy. Miramar, FL 33025
(Do not send product for repair to this address)
International Warranties:
Products purchased outside the United States of America are covered only
by that country’s distributor and not by JL Audio, Inc.
MV600/1_MAN_071519
Loading...