JL Audio MM80-HR User Manual
AUX IN 1
FM ANT
AUX IN 2 Zone 1 OUT Zone 3 OUT
NMEA 2K
USB
PWR
(L)
(1)
(2)
(R)
Speaker
Outputs
Left
+12V Power
Connections
Amp
Battery
Fuse
(not included)
Left
Zone 1
Zone 2
Right
Left
Right
Fuse
(not included)
Amplier On
High-Level Input/
Mic Connection
Motorola® Style
Antenna
RCA Pair
AUX IN 1
RCA Pair
AUX IN 2
RCA Pair
Zone 1 OUT
NMEA 2000®
Network
USB Type A
(2)
RCA Pair
Zone 3 OUT
Ignition +12V DC
Ground
Power +12V DC
What’s Included
(1) MM80-HR
(1) Wire harness
(4) Stainless steel mounting screws
(1) NMEA 2000® drop cable (6.3 ft / 1.92 m)
(1) NMEA 2000® T-connector
(1) User manual
Product Description
The MM80-HR is a hideaway marine source unit designed for use with NMEA
2000® networks. Audio system control functionality is provided using compatible
multi-function displays (MFD) and can vary by MFD. Refer to your MFD
manufacturer for device compatibility information.
Installation Applications
This product is designed for operation with 12 volt, negative-ground electrical
systems. Using this product in systems with positive ground and/or voltages
other than 12V may result in damage to the product and will void the warranty.
This product is not certified or approved for use in aircraft.
Safety Considerations
• Install this product in a dry, well-ventilated location that does not interfere with
other vessel safety or electronic devices.
• While this product is designed to be water-resistant, it should never be
submerged under water or exposed to heavy spray/splashing.
• Do not mount this product in the engine compartment or in any areas of
extreme heat.
• Securely mount this product so that it does not come loose in the
event of a collision/sudden jolt or as a result of repeated vibrations during
normal operation.
• Check before drilling to make sure that you will not be drilling into an exterior
panel/hull, fuel tank, gas/brake line, wiring harness, or other vital system.
• Do not run system wiring outside or underneath the vessel. This is an extremely
dangerous practice, which can result in severe damage/injury.
• Protect all system wires from sharp edges (metal, fiberglass, etc.) by
carefully routing them, tying them down and using grommets and loom
where appropriate.
• Secure all wiring as needed, using cable ties or wire clamps to protect them
from moving parts and sharp edges.
Control Functions
Audio system control functionality of your MM80-HR is provided using
compatible multi-function displays (MFD) and can vary by MFD. Refer to your
MFD manufacturer for device compatibility information.
Panel Connections
Remaining connection points are designed to interface with audio equipment,
media devices and vessel networks. Depending on your specific equipment,
you may or may not use all of the connections. Carefully plan the layout of your
system prior to routing wires and making connections. Refer to the table below
for additional info.
Label Description Connection
FM ANT Antenna
AUX IN 1
AUX IN 2
Zone 1 OUT
Zone 3 OUT
NMEA 2K
USB (1)
USB (2)
White RCA
Red RCA
White RCA
Red RCA
White RCA
Red RCA
White RCA
Red RCA
Red, 5-pin NMEA 2K
Micro-C Connector
USB Type-A
Connect to Motorola® style antenna
Left Channel Signal Input / Auxiliary 1
Right Channel Signal Input / Auxiliary 1
Left Channel Signal Input / Auxiliary 2
Right Channel Signal Input / Auxiliary 2
Left Channel Signal Output / Zone 1
Right Channel Signal Output / Zone 1
Left Channel Signal Output / Zone 3
Right Channel Signal Output / Zone 3
Connect to NMEA 2000® network (LEN 1)
Connect to USB storage device or media player
OWNER’S MANUAL
Hideaway Marine Source Unit
IPX2
WATE R
RESISTANT
Thank you for purchasing a JL Audio MediaMaster®
Source Unit for your sound system.
Your product has been designed and manufactured to exacting
standards in order to ensure years of musical enjoyment. For maximum
performance, we highly recommend that you have your MM80-HR
installed by an authorized JL Audio dealer. Your authorized dealer has
the training, expertise and installation equipment to ensure optimum
performance from this product. Due to the complexity of modern marine
electrical systems, we do not recommend self-installation unless you have
extensive experience in marine electrical systems. Should you decide to
install the amplifier yourself, please take the time to read this manual
thoroughly to familiarize yourself with its installation
requirements and setup procedures.
If you have any questions regarding the instructions in this manual or any
aspect of the product’s operation, please contact your authorized
JL Audio dealer for assistance. If you need further assistance, please
contact the JL Audio Technical Support Department at
technical@jlaudio.com or call (954) 443–1100 during business hours.
Wiring Harness Connections
All connections are made along the lower end panel of the MM80-HR. The
14-pin plug with wire leads is used to make power and speaker related
connections. Carefully plan the layout of your system prior to routing wires and
making connections. Refer to the table below when making connections.
Disconnect the NEGATIVE battery post connection and secure
the disconnected cable to prevent accidental reconnection.
This is an essential safety precaution during installation!
Label Wire Color Connection
Connect to the positive (+12V) battery post. Always
POWER
+12V DC
IGNITION
+12V DC
GROUND Black
AMPLIFIER ON Blue/White
ZONE 1
LEFT SPEAKER
ZONE 1
RIGHT SPEAKER
ZONE 2
LEFT SPEAKER
ZONE 2
RIGHT SPEAKER
HIGH LEVEL
INPUT
Red
Yellow
White
White/Black
Grey
Grey/Black
Green
Green/Black
Purple
Purple/Black
Brown
Brown/White
install an appropriate fuse within 18 inches (45 cm) of
a +12V connection. If this is the only device using the
connection point, use a 15 amp fuse.
Connect to a switched positive (+12V) source. This can be
an ignition controlled, accessory circuit or a vessel battery
equipped with a main disconnect switch. Always install
an appropriate fuse within 18 inches (45 cm) of a +12V
connection. If this is the only device using the connection
point, use a 5 amp fuse.
Connect to a clean, solid metal grounding point or to the
NEGATIVE battery post. Ideally, the +12V DC and Ground
connections of the source unit and amplifiers should be
made at the same location to minimize noise.
This wire provides a positive (+12V) turn-on voltage to
activate aftermarket amplifiers.
(+) Positive Front Left Speaker Output
(–) Negative Front Left Speaker Output
(+) Positive Front Right Speaker Output
(–) Negative Front Right Speaker Output
(+) Positive Rear Left Speaker Output
(–) Negative Rear Left Speaker Output
(+) Positive Rear Right Speaker Output
(–) Negative Rear Right Speaker Output
(+) Positive High Level / MIC Input
(–) Negative High Level / MIC Input
Specifications
AUX IN 1
FM ANT
AUX IN 2 Zone 1 OUT Zone 3 OUT
NMEA 2K
USB
PWR
(L)
(1)
(2)
(R)
3.07 in.
78 mm
4.39 in.
112 mm
8.65 in.
220 mm
9.08 in.
231 mm
2.21 in.
56 mm
General
Operating Voltage 10 - 16V DC
Current Draw Standby: 5 mA / Maximum: 15 A
Fuse Value 15 A
NMEA 2000® LEN 1
Temperature Range
Water Resistance Rating IPX2
Compliance FCC Part B, subpart J; CE per EN 60945; C-Tick
Dimensions 9.08 in. x 4.39 in. x 2.21 in. (231 mm x 112 mm x 56 mm)
Weight 1.96 lbs (0.88 kg)
Audio Outputs/Inputs
AUX In 1, AUX In 2 and
MIC/High Level
Input Sensitivity
Zone 1 & Zone 3
RCA Outputs
Zone 1 & Zone 2
Speaker Outputs
Frequency Response 20 Hz - 20 kHz
S/N Ratio 95 dB (Referred to 1 W)
Total Harmonic Distortion <1% @ 4 Ω (Referred to 1 W, 4 Ω load, 20 Hz - 20 kHz)
Tuner
FM Tuner
AM Tuner
Bluetooth®
Core Specication v4.0
Connection Range: Up to 35 ft / 11 m
USB
Interface v1.1, v2.0
Maximum Charge Capacity 1 A
File Support Type FAT16, FAT32, NTFS
Apple Compatibility iPhone5 / iPod Touch 5 and beyond
Operating: -4 F to +140 F (-20 C to +60 C)
Storage: -22 F to +185 F (-30 C to +85 C)
1V RMS
2V RMS
30W RMS x 4 @ 4 Ω
US: 87.9 to 107.9 MHz
EU: 87.5 to 108.0 MHz
JPN: 76.0 to 90.0 MHz
US: 530 to 1710 kHz
EU: 531 to 1611 kHz
Prole A2DP, AVRCP, PBAP, HSP
Codec SBC
Regulatory Statements
This device:
• complies with CE under R&TTE directive 1999/5/EC
• complies with the requirements of level 2 devices of the Radio communications
(Electromagnetic Compatibility) standard 2008
• This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Industry Canada IC RSS-GEN, Sec 7.1.3 Warning Statement
(Required for license-exempt devices.)
This device complies with Industry Canada
license-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference,
including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence. L’exploitation est autorisée
aux deux conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage,
et (2) l’utilisateur de l’appareil doit accepter
tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le
fonctionnement.
Warning
The user is cautioned that any changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority to operate the
equipment.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that the interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that of the receiver
• Consult the dealer or an experienced technician for help
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
Countries of intended use in the EU
AT - Austria
BE - Belgium
BG - Bulgaria
CH - Switzerland
CY - Cyprus
CZ - Czech Republic
DE - Germany
DK - Denmark
EE - Estonia
ES - Spain
FI - Finland
FR - France
GR - Greece
HU - Hungary
IE - Ireland
IS - Iceland
IT - Italy
LI - Liechtenstein
LT - Lithuania
LU - Luxembourg
LV - Latvia
MT - Malta
NL - Netherlands
NO - Norway
PL - Poland
PT - Portugal
RO - Romania
SE - Sweden
SI - Slovenia
SK - Slovakia
TR - Turkey
UK - United Kingdom
Limited Warranty – Electronics (USA)
JL Audio warrants this product to be free of defects in materials and
workmanship for a period of two (2) years from the original date of purchase.
This warranty is not transferable and applies only to the original purchaser
from an authorized JL Audio dealer. Should service be necessary under this
warranty for any reason due to manufacturing defect or malfunction, JL
Audio will (at its discretion), repair or replace the defective product with new
or remanufactured product at no charge. Damage caused by the following is
not covered under warranty: accident, misuse, abuse, product modification or
neglect, failure to follow installation instructions, unauthorized repair attempts,
misrepresentations by the seller. This warranty does not cover incidental or
consequential damages and does not cover the cost of removing or reinstalling
the unit(s). Cosmetic damage due to accident or normal wear and tear is not
covered under warranty.
Warranty is void if the product’s serial number has been removed or defaced.
Any applicable implied warranties are limited in duration to the period of the
express warranty as provided herein beginning with the date of the original
purchase at retail, and no warranties, whether express or implied, shall apply
to this product thereafter. Some states do not allow limitations on implied
warranties, therefore these exclusions may not apply to you. This warranty gives
you specific legal rights, and you may also have other rights, which vary from
state to state.
If you need service on your JL AUDIO product:
All warranty returns should be sent to JL Audio ’s Electronics Service
Facility freight-prepaid through an authorized JL Audio dealer and must be
accompanied by proof of purchase (a copy of the original sales receipt). Direct
returns from consumers or non-authorized dealers will be refused unless
specifically authorized by JL Audio with a valid return authorization number.
Warranty expiration on products returned without proof of purchase will be
determined from the manufacturing date code. Coverage may be invalidated
as this date is previous to purchase date. Non-defective items received will
be returned freight-collect. Customer is responsible for shipping charges and
insurance in sending the product to JL Audio. Freight damage on returns is not
covered under warranty.
For Service Information in the U.S.A. please call
JL Audio Customer Service:
(9 5 4) 4 43-11 0 0
9:00 AM – 5:30 PM (Eastern Time Zone)
JL Audio, Inc.
10369 North Commerce Pkwy.
Miramar, FL 33025
(Do not send product for repair to this address)
International Warranties:
Products purchased outside the United States of America are covered only
by that country’s distributor and not by JL Audio, Inc.
MM80-HR-MAN 051617
IPX2 Water Resistance Rating
This product has been tested to withstand dripping water when rotated 15
degrees in any direction from vertical for at least 10 minutes. Note - while
designed to be water resistant, this product should never be submerged under
water or exposed to heavy spray/splashing that exceeds its rating.
Loading...