JL Audio M6-10IB User Manual

OWNER’S MANUAL
Marine Subwoofer with
Transflective
Thank you for choosing a JL Audio Marine Subwoofer.
With proper installation, your new speaker will deliver
We strongly recommend that you have your subwoofer
installed by your authorized JL Audio dealer.
RGB LED Lighting (optional)
years of listening pleasure.
The installation professionals employed by your dealer have
the necessary tools and experience to properly install this product.
If you prefer to perform your own installation,
beginning the process.
PHYSICAL SPECIFICATIONS
B
A
LIGHTING
SPEAKER SPEAKER
D
C
E
Physical Specifications M6 -10I B
Nominal Diameter 10 in / 250 mm Outer Diameter (A) 10.75 in / 273 mm Bolt Hole Circle (B) 9.70 in / 247 mm
Frontal Grille Protrusion-Classic* (C) 1.66 in / 42 mm
Frontal Grille Protrusion-Sport* (C) 1.66 in / 42 mm
Mounting Hole Diameter (D) 8.875 in / 225 mm
Mounting Depth (E) 5.90 in / 150 mm
Net Weight 12.60 lbs / 5.70 kg
Driver Displacement 0.052 ft / 1.47 litres
* Frontal grille protrusion measured from mounting surface (Sport Grille Pictured)
INCLUDED PARTS
• One Polymer Subwoofer Grille
• One Polymer Subwoofer Grille Trim Ring
• Six #10 x 1 5/8-inch (41 mm) Phillips pan-head stainless-steel screws
• Six #10 stainless-steel washers
LED Equipped Models
Integrated Transflective™ RGB LED lighting system (patent-pending) delivers smooth, even accent illumination, with no hot spots. LED functionality requires separate wiring at each speaker location. Adjustable control of RGB lighting requires the use of an RGB lighting controller (sold separately). For optimal performance, we recommend using the JL Audio marine lighting controller (MLC-RW).
Subwoofer Parameters M6-10IB
Free Air Resonance (Fs): 43.76 Hz
Electrical “Q” (Qes): 0.907
Mechanical “Q” (Qms): 11.315
Total Speaker “Q” (Qts): 0.840
Equivalent Compliance (Vas): 0.98 ft
One-way, Linear Excursion (Xmax)*: 0.52 in / 13.2 mm
Efficiency (1W/1m)**: 86.1 dB SPL
Effective Piston Area (Sd): 50.11 in / 0.0323 m
DC Resistance (Re): 4.543 ohm
Nominal Impedance: 4 ohm
Infinite Baffle Use: Yes
Enclosure Use: Yes (Sealed & Ported)
Power Handling (continuous): 250W
* Xmax specifications are derived via one-way voice coil overhang method with no
correction factors applied.
** Efficiency (1W/1m) is not an accurate indicator of a subwoofer’s output capability
and should not be used as a comparison to other subwoofers to determine which one is “louder” !
We recommend the use of this speaker in a bi-amplified system using high-quality satellite speakers and amplifiers. We do not recommend the use of this subwoofer with a passive crossover (coil), as this type of device will adversely affect performance.
3
/ 27.75 litres
2 JL AUDIO M 6 -10 I B
All specifications are subject to change without notice.
While this speaker is designed to be water and spray resistant, it is not
designed to be submerged or to withstand high-pressure water spray. Please
exercise care when washing your boat to avoid damaging your speaker. Do
not install on submersibles, personal watercraft or any other vessel likely to
be under water at any time.
Prolonged exposure to sound pressure levels in excess of 100dB can cause
permanent hearing loss. This high-performance speaker can exceed this level.
Please exercise restraint in its operation in order to preserve your ability to
enjoy its fidelity.
When installing a subwoofer in your vessel, it is extremely important to secure
it firmly. This applies not only to the woofer itself, but also any structure it
is mounted to. If not firmly attached, the speaker can become dangerous
projectile in a collision. Please review the mounting information carefully and
use the supplied marine-grade hardware to mount this product.
It is absolutely vital that your speaker is connected as shown in this manual.
Failure to connect the system as shown will result in damage to your speakers
which is NOT covered under warranty.
Do not attempt to remove the lighting LEDs from from the speaker. The LEDs
are permanently fixed and attempting to remove them will cause damage
and this damage will not be covered under warranty.
JL AUDIO M 6 -10 I B 3
All specifications are subject to change without notice.
ENCLOSURE SPECIFICATIONS
W
H
D
ID
L
Subwoofer Recommended Sealed Design
M6-10IB
Volume
(net int.)
2.00 ft
56.6 litres
External Dimensions
(Width x Height x Depth)
17 in x 17 in x 16.25 in
432 mm x 432 mm x 413 mm
F3
(Hz)
41.54 53.41 1.0253
Sealed Design Ported Design
D
H
W
Subwoofer Recommended Ported Design
M6-10IB
Volume
(net int.)
2.50 ft
70.8 litres
External Dimensions
(Width x Height x Depth)
17 in x 17 in x 20.50 in
432 mm x 432 mm x 676 mm
Round Port Specs
(Inner Diameter x Length)
4 in x 12 in
102 mm x 305 mm
Fc
(Hz)
Tune to:
(Hz)
30 25.09
Qtc
F3
(Hz)
NOTE: The enclosure recommendations listed are external dimensions which assume the use of 3/4" (19mm) thick material. If you are using 5/8" (16mm) thick material, subtract 1/4" (6.5mm) from each dimension. Do not use any material with a thickness of less than 5/8" (16mm) as this may compromise the rigidity of the enclosure.
NOTE: All enclosure volumes listed are net internal volumes! Box volume displacement, port displacement and brace displacement must be added to obtain the final gross internal volume. All enclosure dimensions listed have already taken this into account.
4 JL AUDIO M 6 -10 I B
All specifications are subject to change without notice.
TRANSFLECTIVE RGB LED LIGHTING
Illuminated speaker models are equipped with our innovative Transflective™ RGB LED lighting system (patent pending). Fully integrated into the speaker chassis, state­of-the-art LED rings are positioned behind the woofer cones to produce vibrant accent lighting that is remarkably smooth and even, with no hot spots. A cable harness located between the woofer terminals includes wire leads for LED connections. Refer to the table below for individual RGB wire connection info. Note: Wiring connections at each
speaker location are required for LED functionality.
Wire Color RGB LED Connection
Red Red RGB LED Negative (–)
Green Green RGB LED Negative (–)
Blue Blue RGB LED Negative (–)
Yello w Main RGB LED Positive (+12V)
Adjustable control of RGB lighting may be achieved with the use of an RGB lighting controller (sold separately). Refer to the instructions of your RGB lighting controller for specific connection info. Note: When selecting an RGB lighting controller, make sure
that the total amperage demands of all LED circuits does not exceed the output
capacity of the controller. Refer to the table below for the individual current draw amounts and sum (add) the total. For optimal performance, we recommend using
the JL Audio marine lighting controller (MLC-RW).
RGB LED SPECIFICATIONS
Specification M6 -10
LED Curre nt Draw at 12V DC 594 mA
Recommended Fuse Value 750 mA
LED Voltage Range 10 - 14.4V DC
DIRECT LED WIRING
Alternatively, you may hard wire individual leads or a combination of leads to achieve up to seven different LED color assortments. Refer to the table below for the wire colors used to achieve specific LED colors.
LED Color Wire Color(s) Connection
Red Red
Green Green
Blue Blue
Yello w Red and Green
Pink Red and Blue
Aqua Green and Blue
White Red, Green and Blue
Combine all YELLOW (+12V ) leads together (parallel) and connect to a switched +12V supply. See below for additional info.
Combine selected wires from all speakers and connect to negative ground or to the negative (–) battery post.
LED WIRING CONSIDERATIONS
• Do not connect to 24V electrical systems.
• Do not connect the speakers’ LED lights to the vessel’s navigational
lighting circuits.
• For short-circuit protection, we recommend installing a fuse (not included) at
EACH speaker’s YELLOW (+12V) LED power connection lead. Refer to the RGB LED Specifications table (at left) for recommended fuse ratings.
• We recommend a minimum of 16AWG wire size for each speaker’s LED
connection circuits.
• In addition to the above, we recommend activating the speakers’ LEDs thru
a cabin/interior lighting circuit that supplies +12V via an existing switch. If an existing switched circuit is not available, you may install a dedicated toggle/ rocker style switch that will supply positive (+12V) power. Fuse this main +12V connection according to the total amperage demands of all LED circuits. Refer to the RGB LED Specifications table (at left) for individual current draw amounts and recommended fuse ratings.
JL AUDIO M 6 -10 I B 5
All specifications are subject to change without notice.
BEFORE YOU BEGIN INSTALLING
• Check with your local waterway authority for any regulations regarding the use of accent/speaker lighting on your vessel.
• Turn off the audio system. It is also advisable to disconnect your battery system whenever performing installation work.
• Before cutting, drilling or inserting any screw, check clearances on both sides of the planned mounting surface. Also check for any potential obstacles, such as wiring harnesses, fuel lines, hydraulic lines, etc. Check both sides of the vessel before cutting any holes.
• If you are running cables through bulkheads, drill holes for the cable and use a urethane or plastic grommet to protect the wire from chafing in the hole. Make sure that the cables will clear any mechanical devices in the boat and secure them with wire ties.
• Wear protective eyewear at all times and a dust mask and gloves when drilling or cutting.
SPEAKER CONNECTIONS
from
amplier
positive
output
LIGHTING
SPEAKER SPEAKER
from LED
activation wires
or RGB ligh ting
controller output
(LED models only)
from amplier negativ e
output
INSTALLATION PROCEDURE
Diagrams A & B (page 7) shows typical installation procedures into a fiberglass panel, using the supplied hardware. Always follow proper safety procedures. Use eye-protection at all times and a dust mask and gloves when cutting.
1) Choose a flat mounting surface that has sufficient depth and air space behind it to accept the subwoofer.
2) Using a hole saw or jigsaw, cut a 8.875-inch (225 mm) diameter hole.
3) Route the speaker cable to the mounting location. For LED equipped models, now is also a good time to run wires to the speaker location for LED activation.
4) Place the woofer in the hole and mark the screw hole locations using a sharp, pointed tool.
5) Remove the woofer and drill a pilot hole (see the Pilot Hole Recommendations chart at the right) in each of the screw locations. It is also advisable to use a hand-driven countersink tool on each hole to further inhibit gel-coat cracking of fiberglass panels.
6) Connect the speaker wires from the amplifier to the woofer connections (see Speaker Connections at right).
7) If equipped, connect the LED circuit leads (see page 5).
8) Place the woofer, with its grille in place, into the opening and while holding the speaker firmly in its mounting location, evenly snug the mounting screws in a criss-cross pattern, then hand tighten in a criss-cross pattern.
#10 SCREW: PILOT HOLE RECOMMENDATIONS
Fiberglass Thickness Recommended Pilot Hole Drill Size
0.125 in. (3.18 mm) or less 1/8 in. (3.18 mm) pilot hole
foam core / fiberglass sandwich 1/8 in. (3.18 mm) pilot hole
larger than 0.125 in (3.18 mm) 9/64 in. (3.57 mm) pilot hole
Non-standard installations may require different hardware. Always use
marine-grade, stainless-steel fasteners to ensure a secure, reliable installation.
6 JL AUDIO M 6 -10 I B
All specifications are subject to change without notice.
DIAGRAM A
Classic Grille Model Installation
DIAGRAM B
Sport Grille Model Installation
JL AUDIO M 6 -10 I B 7
All specifications are subject to change without notice.
RECOMMENDED CONTINUOUS RMS POWER RANGE FOR ONE SUBWOOFER DRIVER:
MEDIUM G RAY MINIMU M:
From a reliability standpoint, this zone represe nts a ver y comfor table op erating power range for each drive r. This level of power will not stress th e woofer but will not e xtrac t all of its performance potential, either.
Use of less th an the minimum power level will not damage the wo ofer, but may re sult in unsatisfactory performance.
When designing systems with our drivers, it is very important to achieve a good power match between the subwoofer amplifier and the subwoofer driver's capabilities. The power levels listed in the above chart represent continuous (RMS) amplifier power per woofer and assume that the user will regularly make full use of that power without drastically overdriving the amplifier(s). Make sure you factor system impedance and the total number of subwoofers into your calculations. Adhering to these power recommendations will result in systems that are both reliable and enjoyable.
LIGHT GRAY OPTIMUM:
This zone represents the best compromise between long-term reliability, high-output and low-distort ion per forman ce. This po wer level is lower than the woofer’s continuous power rating (as publish ed in its sp ecifi cations), bu t you will st ill be taking advantage of the woofer’s, low-distortion perfo rmance range wit hout undue risk of f ailure.
DARK G RAY MAXIMUM:
Slightly m ore SPL will b e gained by pushing th e power into this zone, bu t typically not m ore than 2dB, compa red to the ligh t gray zone. Th e subwoofe r driver is d esigned to opera te safely up to this p ower range, but not beyond. Operate with caution.
BLACK WARR ANTY VOI D:
We do not recommend operating wo ofers at this level o f power. In this z one, ther e is a very high prob abilit y that the dr iver will f ail due to excessive heat and/or mechanical stress.
Subwoofer drivers ope rated at t hese levels of power are NOT covered under warranty.
JL AUDIO LIMITED WARRANTY USA
Marine Subwoofer Components
JL AUDIO warrants this speaker to be free of defects in materials and
workmanship for a period of two (2) years from the original date of purchase.
This warranty is not transferable and applies only to the original purchaser of the product from an authorized JL AUDIO dealer. Warranty is voided if the factory-applied product serial number is removed or defaced.
Damage caused by the following is not covered under warranty: accident, misuse, abuse, product modification or neglect, failure to follow installation instructions, unauthorized repair attempts, misrepresentations by the seller. This warranty does not cover incidental or consequential damages and does not cover the cost of removing or reinstalling the unit(s). Cosmetic damage due to accident or normal wear and tear is not covered under warranty.
Should service be necessary under this warranty for any reason due to manufacturing defect or malfunction, JL AUDIO will, at its discretion, repair or replace the defective product with new or remanufactured product at no charge.
Products installed as original equipment by boat manufacturers are covered by the boat manufacturer’s warranty, not JL Audio, Inc.
Any applicable implied warranties are limited in duration to the period of the express warranty as provided herein beginning with the date of the original purchase at retail, and no warranties, whether express or implied, shall apply to this product thereafter. Some states do not allow limitations on implied warranties, therefore these exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
If you need service on your JL AUDIO product:
All warranty returns should be sent to JL AUDIO freight prepaid through an authorized JL AUDIO dealer and must be accompanied by proof of purchase (a copy of the original sales receipt.) Direct returns from consumers or non­authorized dealers will be refused unless specifically authorized by JL AUDIO with a valid return authorization number. Warranty expiration on products returned without proof of purchase will be determined from the manufacturing date code. Coverage may be invalidated as this date is previous to purchase date. Return only defective components. Non-defective items received will be returned freight­collect. Customer is responsible for shipping charges and insurance in sending the product to JL AUDIO. Freight damage on returns is not covered under warranty. Always include proof of purchase (sales receipt).
JL Audio customer service: (954) 443-1100 during normal business hours (Eastern Time)
For Service Information in the U.S.A. please call:
JL Audio, Inc
10369 North Commerce Parkway, Miramar, FL 33025
International Warranties:
Products purchased outside the United States of America are covered only by that country’s distributor and not by JL Audio, Inc.
Printed in U.S.A. M6-10IB_01182019_SKU#011513
Loading...