Owner’s Manua l
IMPORTANT SAFETY INSTRUCTIONS
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
AMP PANEL OR SPEAKER. NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED PERSONNEL.
1) Read the Instructions — All safety and operating instructions should be
read before the subwoofer is operated.
2) Retain the Instructions — e safety and operating instructions should be
retained for future reference.
3) Heed Warnings — All warnings on the subwoofer and in the operating
instructions should be followed.
e lightning ash with arrowhead
symbol, within an equilateral triangle, is
intended to alert the user to the presence
of uninsulated “dangerous voltage” within
the product’s enclosure that may be of
sucient magnitude to constitute a risk of
electric shock to persons.
e exclamation point within an
equilateral triangle is intended to alert the
user to the presence of important operating
and maintenance instructions in the
literature accompanying the product.
4) Follow Instructions — All operating and use instructions should
be followed.
5) Water and Moisture — e subwoofer should NOT be used near water – for
example, near a bathtub, washbowl, sink, laundry tub, in a wet basement,
near a swimming pool, etc.
6) Ventilation — e subwoofer should be situated so that its location or
position does not interfere with its proper ventilation. For example, the
subwoofer should not be situated on a bed, sofa, rug, or similar surface
that may block airow over the heatsink ns. If placing the subwoofer in
a “built-in” installation, ensure that airow to the heat sink at the rear of
the subwoofer is not impeded. Do not cover the subwoofer heatsink with
tablecloths, curtains, etc.
9) Heat and Flames — e subwoofer should be situated away from heat
sources such as radiators, heat registers, stoves, replaces, or other devices
which produce heat. Do not place candles on top of or near the subwoofer.
10) Power sources — e subwoofer should only be connected to a power supply of
the type described in the operating instructions or as marked on the subwoofer.
e Gotham v2 has a very powerful amplier. For maximum performance,
please utilize a dedicated AC power circuit. We suggest minimum circuit breaker
sizes of 120 VAC / 20 amps or 230 VAC / 10 amps.
IMPORTAN T
| Gotham v2Page 2
11) Power Cord Protection — Power-supply cords should be routed so that they
are not likely to be walked on or pinched by items placed upon or against
them, paying particular attention to cords at plugs, convenience receptacles,
and the point where they exit the subwoofer.
12) Cleaning — e subwoofer should be cleaned only as recommended in the
operating instructions.
13) Nonuse Periods — e power cord of the subwoofer should be unplugged
from the outlet when the subwoofer is le unused for long periods of time.
14) Lightning and Power Surges — We recommend that you disconnect the
subwoofer from the electrical outlet during electrical storms and/or recurring
power interruptions to prevent damage due to power surges.
15) Object or Liquid Entry — Care should be taken so that objects do not fall
into and liquids are not spilled onto the subwoofer enclosure. Do not expose
the subwoofer to dripping or splashing from liquids. Do not place objects
lled with liquids on top of, or near the subwoofer. For example: ower vases,
beverages, liquid-fueled lamps, etc.
16) Damage Requiring Service — e subwoofer should be serviced by qualied
service personnel when:
a. the power-supply cord or plug has been damaged
b. objects have fallen or liquid has been spilled into the subwoofer
c. the subwoofer has been exposed to rain
d. the subwoofer does not appear to operate normally or exhibits a marked
change in performance
e. the subwoofer has been dropped or the cabinet has been damaged
f. the subwoofer driver’s cone and/or suspension has been
physically damaged
WARNING
17) Servicing — e user should not attempt to service the subwoofer beyond
what is described in the operating instructions. All other servicing should be
referred to qualied service personnel.
18) Overloading — Do not overload wall outlets, extension cords, or outlet strips
as this can result in a risk of re or electric shock.
19) Grounding — is subwoofer is supplied with a three-prong, grounded
power cord. Precautions should be taken so that the grounding means of the
subwoofer are not defeated. Defeating the grounding prong on the subwoofer
power cord could increase the risk of electric shock and could result in
permanent damage to the subwoofer’s electronics.
THIS SUBWOOFER IS CAPABLE OF PRODUCING VERY HIGH SOUND
PRESSURE LEVELS. PLEASE EXERCISE RESTRAINT IN ITS OPERATION TO
PROTECT YOUR HEARING FROM PERMANENT DAMAGE.
Page 3 | Gotham v2
FCC COMPLIANCE STATEMENT
NOTE: is equipment has been tested and found to comply with the limits of Part 15 of the FCC
Rules. ese limits are designed to provide reasonable protection against harmful interference in
a residential installation. is equipment generates, uses and can radiate radio frequency energy
and, if not installed in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment o and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
TABLE OF CONTENTS
Important Safety Instructions: ......................................... 2-3
Introduction:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Product Overview: ...................................................... 5
Placing your Gotham v2 in Your Listening Room: ....................... 6-10
Unpacking your Gotham v2: ............................................ 11
Front Control Panel Layout: ............................................. 12
Rear Control and Connector Panel Layout: ............................... 13
Front Panel Controls in Detail: ........................................14-17
Rear Controls in Detail & Connecting your Gotham v2(s): ................18-25
Recommended Setup Procedure: ......................................26-30
Frequently Asked Questions: ............................................ 31
Cleaning Your Gotham v2:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Troubleshooting: ....................................................32-33
Specications: ......................................................... 34
Limited Warranty / Service Information: ................................. 35
INTRODUCTION
Congratulations on your purchase of a JL Audio Gotham v2 powered subwoofer
system. is product has been critically engineered to deliver exceptional
performance in your home theater or audio system for many years to come.
As a company, we are intensely committed to core research into
high-performance loudspeaker and amplier technologies. JL Audio’s longexcursion subwoofer driver designs are widely considered as reference standards for
linear behavior and high output. We have also focused our eorts to create powerful
amplier and signal-processing technologies specically aimed at delivering
exceptional low-frequency performance. Your Gotham v2 combines these core
disciplines within a compact, beautifully craed package to deliver an unparalleled
listening experience.
JL AUDIO TECHNOLOGIES INCLUDED
IN Gotham v2 SUBWOOFERS
DMA-Optimized Motor System
DMA is JL Audio’s proprietary Dynamic
Motor Analysis system aimed at
improving dynamic motor behavior. As a
result of DMA optimization, loudspeaker
motors remain linear in force over an
extreme range of excursion and also
maintain a highly stable xed magnetic
eld over a wide power range. is leads
to vastly reduced distortion and faithfully
reproduced transients... or put simply:
tight, clean, articulate bass.
OverRoll™ Surround
(U.S. Patent #5,687,247 and #5,949,898)
e OverRoll™ surround spans over
the driver’s mounting ange, utilizing
available diameter wasted in conventional
speakers. is allows the use of the wider
roll necessary to control high-excursions
without sacricing precious cone area.
W-Cone™ (U.S. Patent #6,496,590)
e W-Cone™ is a unit-body cone
assembly that delivers astonishing cone
stiness with minimal mass.
Floating-Cone™ Attach Method
(U.S. Patent #6,501,844)
is assembly technique ensures proper
surround geometry in the assembled
speaker for better excursion control and
dynamic voice coil alignment.
Plateau-Reinforced Spider Attachment
(U.S. Patent #6,118,884)
is high-integrity suspension attachment
relieves stress from the spider material at
high-excursions for enhanced reliability.
Elevated Frame Cooling Technology
(U.S. Patent #6,219,431 and #6,229,902)
Delivers cool air, through slots directly
above the top-plate, to the voice coil of the
speaker. is enhances power handling
and sound quality by minimizing
dynamic parameter shis and power
compression.
Radially Cross-Drilled Pole Piece
(U.S. Patent #6,243,479)
is innovative venting system greatly
enhances thermal dissipation and power
handling by directing air ow onto the
voice coil former, working in conjunction
with the Elevated Frame technology.
High-Damping Feedback Circuit
(U.S. Patent #6,441,685)
is proprietary, discrete control circuit
design allows our Class D switching
ampliers to maintain an excellent
damping factor for improved transient
behavior and delity.
| Gotham v2Page 4
We sincerely thank you for your purchase and invite you to read this
manual thoroughly in order to achieve the highest level of performance with
your Gotham v2 subwoofer system. Enjoy.
PRODUCT OVERVIEW
JL Audio Gotham v2 subwoofers combine a state-of-the-art
JLAudio subwoofer driver and electronics/amplier package within
a highly optimized enclosure to deliver an exceptional listening
experience in your home theater or home audio system.
e subwoofer drivers in your Gotham v2 subwoofer system are capable
of exceptional linear excursion without distress or audible distortion. ese
exceptional drivers enable your Gotham v2 to reproduce powerful low-frequency
events with stunning impact and unprecedented accuracy. Derived from JL
Audio’s legendary W7 design platform, the Gotham v2 drivers oer peak-to-peak
excursion capabilities well in excess of 3 inches (76mm) to comfortably handle
the dynamics of the most demanding program material.
To get the most from this long excursion driver platform, a tremendous
amount of controlled power is needed. Our electronics engineering team
conducted an intense analysis of typical program material and its dynamic
demands in order to balance current draw and actual output power requirements
relative to the system’s impedance characteristics. Aer careful study, precisely
engineered switching ampliers employing patented feedback technology were
created to take full advantage of each driver’s full excursion envelope. Compared
to their predecessors, Gotham v2’s have been improved with all new digital
signal processing and a 20% increase in amplier power, further enhancing their
outstanding dynamic capabilities.
e beautiful cabinet enclosing the workings of your Gotham v2 is also the
result of careful engineering. To contain the pressures created by the Gotham v2
driver, we utilize massive, berglass construction with extensive internal bracing
features and advanced assembly techniques.
Your listening room is the other enclosure that aects the way your bass will
sound. All rooms create a specic sonic signature, which must be eectively
managed to achieve well-balanced low frequency performance. To help properly
integrate your subwoofers with your room’s acoustics, all Gotham v2 subwoofers
employ a powerful, Digital Automatic Room Optimization (D.A.R.O.) system.
is system deploys eighteen bands of digital equalization to tame room
acoustics and deliver spine-tingling sub-bass accuracy.
As you can see from this brief introduction, Gotham v2 subwoofer systems
employ many advanced technologies. e contents of this manual will explain the
features, guide you through the setup and tuning of your Gotham v2 subwoofer
and help you achieve your ultimate low-frequency listening experience.
IMPORTAN T
If you require assistance, we urge you to contact your authorized
JL Audio retailer for expert setup advice and service.
IMPORTANT! IT IS A VERY GOOD IDEA TO READ THE NEXT SECTION BEFORE
UNPACKING YOUR Gotham v2. UNPACKING THE SUBWOOFER NEAR ITS
FINAL LOCATION IS RECOMMENDED.
Page 5 | Gotham v2
WARNING: THE GOTHAM v2 IS EXTREMELY HEAVY 405 LBS. / 184 KG
AND IS VERY DIFFICULT TO HANDLE! PEOPLE WITH BACK PROBLEMS
OR MEDICAL CONDITIONS THAT PRECLUDE EXERTION SHOULD NOT
ATTEMPT TO UNPACK OR MOVE A GOTHAM v2.
WARNING: THE UNPACKING INS TRUCTIO NS MUST BE FOLLOWED PRECISELY.
FAILURE TO DO SO MAY RESULT IN PRODUCT DAMAGE AND/OR INJURY.
WARNING: FAILURE TO HANDLE A GOTHAM v2 CORRECTLY DURING
UNPACKING AND PLACEMENT CAN RESULT IN EXPENSIVE DAMAGE
WHICH IS NOT COVERED UNDER WARRANTY.
WARNING
IMPORTANT: YOU WILL NEED AT LEAST TWO STRONG PEOPLE TO MOVE,
UNPACK AND PLACE THE GOTHAM v2. THREE PEOPLE ARE RECOMMEND ED.
IMPORTANT: BEFORE PLACING GOTHAM v2 IN YOUR LISTENING SPACE,
MAKE SURE THAT THE FLOOR STRUCTURE IS CAPABLE OF SUPPORTING
THE WEIGHT OF THE PRODUCT. CONSULT A PROFESSIONAL ENGINEER
IF NECESSARY.
IMPORTAN T
| Gotham v2Page 6
PLACING YOUR GOTHAM v2 IN YOUR LISTENING ROOM:
Your listening room or theater is an integral part of your sound reproduction
system. e physical dimensions of the room and its furnishings, materials, doors
and windows play an important role in dening how your system sounds.
When you place a sound source in an enclosed rectangular space, “standing
waves” are created, resulting from the relationship between the sound’s
wavelength and your room’s dimensions. In other words, standing waves result
from sound energy that is trapped in the room as it bounces back and forth
between opposing walls. Standing waves in the room create acoustic peaks and
dips where the sound is either louder or soer, based solely on your physical
position in the room. Energy also “builds up” at the room’s boundaries, creating
exaggerated bass response at certain frequencies. ese fundamental room
resonances are called room “modes.”
e moral of this mode story is to try and avoid seating positions in standing
wave peak or dip regions. It is highly recommended that you place your listening
chairs in areas where modal peaks and dips are moderate and do not reinforce
one another. e two most obvious areas to avoid are those near the exact center
of the room and those close to any of the room’s walls.
Just as your listening seat can be in a peak or dip region, so can your
subwoofer. When placed in a room corner, a subwoofer maximally excites the
room’s mode structure, creating the strongest output with the fewest dips. When
the subwoofer is pulled away from a corner or wall, the room modes are excited
less, which can alter the sound at your listening seat.
Be sure to experiment with both your listening seat position and subwoofer
position to nd the best solution. Careful experimentation usually leads to a
superior sounding system. Use our setup suggestions (illustrated on the opposing
page and the following pages) to get you started.
If you cannot avoid placing your sofa against the back wall, or your
subwoofer in a less than optimal position, your Gotham v2’s Digital Automatic
Room Optimization (D.A.R.O.) System can dramatically improve
these less-than-ideal situations.
We recommend that you begin by placing your Gotham v2 in the front
of the room, near the front le or right speaker. Placing it directly in the
front corner of the room will produce the maximum number of peaks and
the minimum number of dips in the bass response. is can be advantageous
because the Gotham v2’s D.A.R.O. system can correct the resulting peaks very
eectively, whereas dips in response cannot be corrected via equalization. Dips in
response can only be minimized via careful subwoofer and listener placement.
Placing the Gotham v2 near solid walls will reinforce bass response and
pulling it away from solid walls will decrease bass. Increasing the distance
between the subwoofer and the walls may help to smooth upper bass response in
some rooms.
We recommend that you avoid placing the Gotham v2 near windows to prevent
rattling and sound transmission to the outside world.
SPECIAL CONSIDERATIONS FOR HANDLING THE GOTHAM v2
e Gotham v2 is extremely heavy and can be dicult to handle. Failure
to handle it correctly during unpacking and placement can result in expensive
damage which is not covered under warranty.
Page 7 | Gotham v2
Recommended Subwoofer Placement Options for One Gotham v2
MORE INTENSE
SMOOTHER
SMOOTHER
SMOOTHER
RECOMMENDED
SUBWOOFER
PLACEMENT
ZONES
(For Single Subwoofer)
MORE INTENSE
SMOOTHER
SMOOTHER
SMOOTHER
COMPROMISED SEATING POSITIONS
(Results in weaker, uneven bass performance)
BEST SEATING POSITIONS
(Most accurate bass performance)
COMPROMISED SEATING POSITIONS
(More intense, but less accurate bass performance)
CENTERLINE OF ROOM
APPROX. 1/3 OF TOTAL ROOM
LENGTH AWAY FROM BACK WALL
CLOSE TO BACK WALL OF ROOM
WORST
SEAT
| Gotham v2Page 8
Using Two Gotham v2s
When using two Gotham v2s, try
placement near the front corners of the
room, at diagonally-opposite corners
of the room, or at the center points of
opposing walls as shown at right.
Experimentation with
subwoofer and listener
placement is recommended to
achieve the best results – the
benets can be substantial.
High-resolution measurements
and professional system calibration
are recommended for the best possible
results & system performance.
Recommended Subwoofer Placement Options for Two Gotham v2s
Page 9 | Gotham v2
Recommended Subwoofer Placement Options for Three Gotham v2s
Using Three or Four Gotham v2s
Research indicates that the
smoothest bass response for a large
listening area can be achieved using
four subwoofers, placing one at
the midpoint of each of the four
walls (although using two or three
subwoofers can be almost as good).
Experimentation with
subwoofer and listener
placement is recommended to
achieve the best results – the
benets can be substantial.
High-resolution measurements
and professional system calibration
are recommended for the best possible
results & system performance.
Recommended Subwoofer Placement Options for Four Gotham v2s
| Gotham v2Page 10
UNPACKING YOUR GOTHAM v2
Now that you have determined your Gotham v2’s position in the room, you can
proceed with unpacking it near its intended location.
* e Gotham v2 subwoofer ships in a protective cloth cover that is not pictured in the unpacking
instructions above. Use the orientation of the Gotham v2™ above as a guide.
IMPORTANT: DUE TO THE WEIGHT OF THE GOTHAM v2 SUBWOOFER,
IMPORTAN T
PLEASE EXERCISE CAUTION WHILE UNPACKING AND POSITIONING IT TO
PREVENT INJURY. ENLIST THE HELP OF ADDITIONAL PEOPLE TO FACILITATE
THE PROCESS. TO MINIMIZE THE RISK OF INJURY, BEND YOUR KNEES AND
LIFT WITH YOUR LEGS, NOT YOUR BACK.
e Gotham v2 box should be unpacked
close to where the subwoofer will be placed.
e subwoofer is packed upside down. is
box must be ipped over CAREFULLY and
EXACTLY AS DESCRIBED to remove the
subwoofer, minimize eort and avoid the
risk of damaging the product.
2
1
Detailed instructions on unpacking the subwoofer:
1. Move the carton near its intended location in the room.
2. Open the top of the carton (observe markings on carton) and remove all of the
items included in the center of the box.
3. With the help of others and using the carton handles, gently lay the carton to
one side holding the aps back and making sure a carton side without handles
rests facing up.
4. Again, holding the carton aps back and employing the help of others, carefully
ip the box onto its top (open end). e box will be upside-down and should
have all of the aps out from underneath it.
5. Pull the carton straight up until it clears the subwoofer and place to one side.
6. Remove the one-piece foam insert from the top of the woofer and place
in the carton.
11. Tilt the subwoofer forward (toward its speaker/grille side) to remove the rear
split-foam insert and place in the carton.
12. Tilt the subwoofer in the opposite direction (towards its silver heatsink) to
remove the remaining split-foam insert and place in the carton.
13. Remove the protective cloth cover and place in the carton.
14. Install one of the included sliding discs under each of the Gotham v2’s three feet
to facilitate pushing/positioning the subwoofer.
IMPORTAN T
IMPORTANT! PLEASE RETAIN ALL PACKAGING FOR SAFE
TRANSPORTATION OF THE SUBWOOFER AND FOR ANY FUTURE SERVICE.
Page 11 | Gotham v2
Front Control Panel
e labeled Figure below depicts the front control panel of a Gotham v2 subwoofer.
Input Mode
page 15
Power
page 14
Level Mod e
page 15
Master Level
page 16
Lights
page 16
Polarity
page 17
max
LP Filter
page 16
A.R .O.
page 14-15
calibration mic.
page 14
phase (deg.)
page 17
e.l.f. trim (dB)
page 17
LP freq. (H z)
page 16
| Gotham v2Page 12
Rear Controls and Connectors
e labeled Figure below depicts the rear panel of a Gotham v2 subwoofer.
Balanced Inputs
page 18
Input Mode
Switches
page 20
Fuse
page 33
Unbalanced
Inputs
page 19
Output to
Slave Connector
page 21
IEC-Style AC
Connector
page 21
Page 13 | Gotham v2
FRONT PANEL CONTROLS IN DETAIL
max
max
Power Switch
e “Power” switch determines the operational readiness of the Gotham v2
subwoofer and should be the only switch used to turn the Gotham v2 on and o. Do
not use a power strip switch, switched outlet or any other external switch as these
may result in undesirable and potentially damaging transient pops. Do not unplug
the Gotham v2’s AC power cord while the unit is turned on. e power switch has
three positions:
“On”: e Gotham v2 is fully powered at all times. Front panel lights are on
unless they have been turned o via the “Lights” switch.
“O ”: e Gotham v2’s internal power amplier is powered down. In this state,
a negligible current draw will exist for operating the main power relays. All front
panel lights are o .
“Aut o”: e Gotham v2 will power up its internal amplier when an audio signal is
present at any of its inputs and will power down the internal amplier if no signal has
been detected at its inputs for thirty (30) minutes. When dormant, the Gotham v2 will
draw a very small amount of current (< 5 watts) to power its signal-sensing circuitry.
Front panel lights will turn o when the Gotham v2 powers down and light when the
Gotham v2 powers up (unless they have been turned o via the “Lights” switch).
In the unlikely event that the Auto feature is not sensitive enough for a particular
system, use a Y-cable adaptor to split the incoming signal into both RCA or XLR
inputs on the Gotham v2. is will increase the input sensitivity by 6 dB. Please be
aware that if the Auto sensitivity is too high or if there is signicant noise on the
input cable, the Gotham v2 may not turn o as desired. If this happens, remove the
Y-cable adaptor or look for the noise source in the upstream components.
IMPORTAN T
Digital Automatic Room Optimization (D.A.R.O.)
A powerful feature of the JL Audio Gotham v2 subwoofers is their innovative
Digital Automatic Room Optimization (D.A.R.O.) technology. is one-touch
system includes 18 bands of digital equalization to eliminate the largest acoustic
response peaks in your home theater at the main listening seat, greatly improving
the in-room low-frequency response. Calibration of the D.A.R.O. system is fully
automated. Please consult the next section of this manual for details on how to use
the D.A.R.O. system.
Using the included JL Audio calibration microphone, the D.A.R.O. calibration
procedure takes less than three minutes. In brief, you will connect the included
microphone to the “Calibration Mic.” input, press the Calibrate button, and then
hold the microphone at ear height in your main listening seat during the test. A
noise sequence will be played through the Gotham v2 subwoofer, and the room
response will be automatically measured, analyzed and equalized. For detailed
instructions on the D.A.R.O. setup procedure, refer to pages 29-30.
Calibration Mic. Input
is input is for connecting the supplied JL Audio calibration microphone to the
Gotham v2 subwoofer. Connect one end of the supplied cable to the microphone and
the other end to this jack prior to using the D.A.R.O. system. e D.A.R.O. system
is specically calibrated to this microphone and its connection scheme is specic to
the supplied microphone. e calibration sequence will not operate when a dierent
microphone is connected or if no microphone is connected.
| Gotham v2Page 14
Demo Button
max
max
max
max
max
e Demo button triggers a 20 second long tone sequence that briey
demonstrates the range of the Gotham v2 subwoofer. e Demo function is useful
for showcasing the output capability of the Gotham v2 and to verify that the Gotham
v2 (or multiple Gotham v2s) are operational during system troubleshooting.
e Demo button is also used (in combination) to clear (return to at) the
D.A.R.O. equalizer settings. To clear the D.A.R.O.’s settings & turn o the Calibrate
light, press and hold the Demo button and then press the Defeat button. Please note
that you must perform this button sequence quickly. If you hold the Demo button
for more than 2 seconds without touching the Defeat button, the Demo tones will
start. Should this happen, simply wait for the Demo sequence to end and try again.
Defeat Button
If “Demo” or “Calibrate” is pressed while the defeat function is active, “Defeat” is
automatically canceled. No other front panel controls will alter the D.A.R.O. Defeat
state. e Defeat setting is stored in non-volatile memory and will not change even if
power is disconnected.
e Defeat button is also used (in combination) to clear (return to at) the
D.A.R.O. equalizer settings. To clear the D.A.R.O.’s settings & turn o the Calibrate
light, press and hold the Demo button and then press the Defeat button. Please note
that you must perform this button sequence quickly. If you hold the Demo button
for more than 2 seconds without touching the Defeat button, the Demo tones will
start. Should this happen, simply wait for the Demo sequence to end and try again.
Calibrate Button
During the D.A.R.O. test sequence, the Calibrate button’s green LED will blink
quickly to alert the user to two special conditions:
1. “JL Audio Microphone NOT Connected”: If you forget to connect the mic
before trying to start a Calibration you will get this alert. Press the Calibrate button
once to cancel the alert, connect the D.A.R.O. microphone, and try again.
2. “Inappropriate Sound Level for D.A.R.O. Calibration”: Since the D.A.R.O.
sequence is completely automatic, this alert likely indicates a problem with the
microphone. Press the Calibrate button once to cancel the alert. Ensure that the JL
Audio microphone is properly connected and try again. For further help, please refer
to Troubleshooting on page 33.
Input Mode Indicators
e Input Mode indicator LEDs show the input mode, either “Master” or “Slave”,
selected by the switch on the Gotham v2’s back panel (unless the “Lights” switch is
set to “o”). For further details, see page 20.
Level Mode
e two-position Level Mode switch allows you to select between
the following modes:
“Reference”: In this mode, the Master Level control knob has no eect on the
Gotham v2’s output level. Use this setting if you will primarily be controlling the
subwoofer level via your receiver or preamplier/processor. For those of us with
small children or overenthusiastic teenagers, this mode of operation will prevent
direct manipulation of the Master Level.
“Variable”: In this mode, the Master Level control knob determines the output
level of the Gotham v2 subwoofer. is mode is also useful when level matching the
Gotham v2 subwoofer to a pair of stereo speakers in a two-channel system.
Page 15 | Gotham v2
Master Level Knob
max
e Master Level Knob is used to control the output level of the Gotham v2
when the Variable Level mode is selected on the front control panel.
When rotated fully counter-clockwise, the Gotham v2’s output will be fully
muted. When at the “0” or vertical position, the Variable gain level matches the
Reference level setting. When turned fully clockwise, the Gotham v2’s output
level is 15 dB higher than the Reference setting.
Lights
e “Lights” selector switch allows the user to select one of three indicator
light modes.
“O” turns o all of the front panel LED’s at all times.
“Dim” sets all of the front panel LEDs to a low brightness level when the
Gotham v2 is turned on.
“On” sets all of the front panel LEDs to full brightness level when the Gotham
v2 is turned on.
IMPORTANT: WHEN TROUBLESHOOTING OR CALIBRATING THE D.A.R.O.
FEATURE, MAKE SURE THAT THE “LIGHTS” SWITCH IS SET TO “DIM” or “ON.”
LP Filter
e Low Pass (LP) Filter selector switch determines the operating mode of the
Gotham v2’s built-in low pass lter.
“O” defeats the low pass lter, completely removing this circuit from the
signal path.
“12 dB” sets the roll o slope of the low pass lter to a 12 dB per octave slope
(Butterworth alignment).
“24 dB” sets the roll o slope of the low pass lter to a 24 dB per octave slope
(Linkwitz-Riley alignment).
e 24 dB setting more aggressively attenuates high frequencies above the LP
Frequency setting (see below). If you are using the Gotham v2’s built-in low pass
lter, experiment with the LP Filter slope setting to achieve the best transition
to your satellite speakers. If you prefer to use the lters and bass management
features in your receiver or preamplier, defeat the on-board lter by selecting
the “O” position.
LP Freq
e Low Pass (LP) Frequency selector knob allows the user to choose the rollo frequency of the Gotham v2’s internal low pass lter. e frequency is variable
between 30 Hz (full counter-clockwise) to 130 Hz (full clockwise). is knob does
not aect the input signal in any way if the LP Filter switch is set to “O ”. 80 Hz
is a commonly used lter frequency and usually serves as a good starting point
for adjustments.
IMPORTAN T
| Gotham v2Page 16
E.L.F. Trim
e Extreme Low Frequency (“e.l.f. trim”) knob allows the user to apply
a certain amount of signal equalization at 24 Hertz (extremely low bass). At
full counter-clockwise rotation, the signal at 24 Hz is cut by 12 dB. At “0” the
equalizer is set at for zero contribution to the signal. At full clockwise rotation,
the signal at 24 Hz is boosted by 3 dB.
e e.l.f. trim feature is useful for tailoring the Gotham v2’s very low
frequency output for your particular room. Adding some boost can make certain
material feel more exciting. Using the cut function can help to compensate for
room or boundary gain in the low frequencies. Room boundaries and the room’s
nite (limited) size naturally cause very low frequencies to be boosted relative
to other parts of the signal. As such, using the e.l.f. trim feature to cut the lowest
frequencies can help to tame “bloat” or unnatural sounding low bass in small to
medium sized rooms (and can also reduce unwanted vibrations in the room or
throughout the house).
Polarity
e Polarity switch allows the user to select between normal (0 deg) and
reversed (180 deg) signal polarity. e Polarity switch will primarily aect the
small frequency range around the crossover point between your subwoofer and
satellite speakers.
Unlike the Phase control, which eectively adds time delay, the Polarity
switch produces an instantaneous reversal of the signal’s amplitude peaks.
For example, if at a given reference point a sine wave has an amplitude peak,
by ipping the phase switch you instantly convert that peak into a trough
or amplitude dip. Because the eect of the Polarity switch is immediate, it
compliments the operation of the Phase control and cannot be replaced by it.
When placing your Gotham v2 in the room, experiment with the Polarity switch
before adjusting the “Phase” control. Either position of the Polarity switch may
provide a smoother transition between your Gotham v2 subwoofer and the satellite
speakers. Use source material with good mid and upper bass content for evaluation.
Phase
e Phase control knob allows the user to adjust the “timing” of the
subwoofer output relative to the main speakers. e Phase control will primarily
aect the small frequency range around the crossover point between your
subwoofer and satellite speakers. Phase settings between 0 degrees (full counterclockwise rotation) and 270 degrees (full clockwise rotation) are possible. e
Phase control’s labels are referenced to a frequency of 80 Hz since this is the most
common crossover point between satellite speakers and a subwoofer.
Speaker, subwoofer, and listening seat positions vary greatly in home
theater installations. Since physical positioning of speakers relative to the room
boundaries, and each other, greatly aects the perceived quality of sound output,
sometimes it is helpful to delay the subwoofer output. is is exactly what occurs
when you turn the Phase control beyond 0 degrees.
Once your Gotham v2 has been placed in your listening room to give you the
smoothest overall sound and aer you have determined the optimum “Polarity”
switch position (see preceding section), experiment with the position of the Phase
control. Using familiar source material with good mid and upper bass content,
adjust the Phase control and listen for better dened mid-bass and a smoother
transition between the subwoofer and satellite speaker systems. If no single
setting sounds better than another, leave the Phase control at 0 degrees.
Page 17 | Gotham v2
CONNECTING YOUR GOTHAM v2
Balanced Inputs
If your home-theater receiver or preamplier/processor provides balanced
outputs, the Gotham v2’s balanced inputs are the preferred connection. Balanced
connections are used extensively in professional studios and sound reinforcement
applications for a number of very good reasons. Besides ensuring proper grounding
between components, balanced signal transmission is designed to cancel induced
cable noise from the surrounding environment (particularly important with long
cable runs). e bottom line is that your system will be far less likely to exhibit
humming or other extraneous noises if you use balanced connections.
e Gotham v2 subwoofers feature individual le and right balanced input
connections with XLR “combo” jacks. ese special jacks accept either a
three-pin male XLR connector or a “tip-ring-sleeve” (TRS) 1/4-inch (6.3 mm)
connector for compatibility with a wide range of equipment.
For systems with a mono subwoofer or “LFE” channel connection, only the
jack labeled “Le or Mono” will be used. is applies to most modern multichannel receivers and preamplier/processors. Separate le and right input jacks
are provided for systems without a dedicated mono subwoofer connection. is
typically applies to two-channel audio equipment.
Appropriate balanced cables are available from your JL Audio dealer and are
not included with the Gotham v2.
Technical Notes:
• Do not use the balanced inputs with unbalanced signals via adaptors. e
unbalanced inputs of the Gotham v2 are optically isolated and preferable in
situations where only an unbalanced signal source is available. Balanced input
impedance is 10 kohms.
• Input connectors are congured according to Audio Engineering Society
recommendations for balanced signal cables as follows:
XLR Connection
Pin 1: Shield
Pin 2: Positive
Pin 3: Negative
TRS connection:
Tip: Positive
Ring: Negative
Sleeve: Shield
e Le and Right inputs on the Gotham
v2 are internally summed to a single mono
channel. Since the Gotham v2 is inherently
a “mono” or single channel device, you
can use the Le and Right inputs for the
master Gotham v2 and then distribute the
summed mono signal to additional slave
Gotham v2s in the system.
IMPORTANT: IF YOUR RECEIVER OR PREAMPLIFIER/PROCESSOR DOES NOT
HAVE XLR OR 1/4-INCH TRS BALANCED OUTPUTS, PLEASE REFER TO THE
“UNBALANCED INPUTS” SECTION ON PAGE 19 FOR INPUT CONNECTION
INFORMATION. DO NOT ATTEMPT TO CONNECT UNBALANCED OUTPUTS
TO THE GOTHAM v2’S BALANCED INPUTS VIA ADAPTORS.
IMPORTAN T
| Gotham v2Page 18
Unbalanced Inputs
e Gotham v2 subwoofer features individual le and right unbalanced RCAtype input connectors. ese are the most commonly used connectors for home
audio applications and must be used if your receiver or preamplier/processor
does not provide balanced outputs. While unbalanced connections are not as
noise-immune as a balanced connection, Gotham v2 subwoofers employ optical
isolation on the unbalanced inputs to minimize the possibility of noise in your
system.
For systems with a mono subwoofer or “LFE” channel connection, only
the RCA-type jack labeled “Le or Mono” will be used. is applies to most
modern multi-channel receivers and preamplier / processors. Separate le and
right RCA-type input jacks are provided for systems without a dedicated mono
subwoofer connection. is typically applies to two-channel audio equipment.
Technical Notes:
• When balanced outputs are not available on the signal source, you must
use the RCA-type unbalanced inputs. Gotham v2s feature optical isolation
circuitry on the unbalanced inputs to minimize the likelihood of ground
loop induced noise. Unbalanced input impedance is 50 kohms.
• Connections are industry-standard for unbalanced signal cables as follows:
RCA-type connection:
Tip: Positive
Sleeve: Negative
IMPORTAN T
IMPORTANT: IF NOISE EXISTS AFTER CONNECTION, GOTHAM v2s ALLOW
FOR GROUNDING OR ISOLATION OF THE UNBALANCED INPUTS. PLEASE
REFER TO THE “INPUT MODE SWITCHES” SECTION ON PAGE 20 OF THIS
MANUAL FOR FURTHER INFORMATION ON MINIMIZING NOISE.
Page 19 | Gotham v2
Input Mode Switches:
Two switches are located on the rear panel to control unbalanced signal
grounding and master/slave operation.
“Grounded / Isolated” Switch
e “Grounded / Isolated” Input Mode switch aects only the unbalanced
RCA inputs and is designed to facilitate a quiet, hum-free connection to your
audio or home theater system. is feature is included to deal with the signal
grounding issues oen encountered in home theater systems when several
components from dierent manufacturers are interconnected.
e Gotham v2 ships with this switch in the “Isolated” mode. If, with all system
components connected and turned on (but no source material playing), you hear
a continuous low-frequency hum through your Gotham v2, ip this switch to the
“Grounded” position and evaluate the dierence in the noise level. Use whichever
switch position provides the least hum or noise.
IMPORTANT: PLEASE NOTE THAT CHANGING ANY COMPONENT IN
THE OPTIMIZED SYSTEM (RECEIVER, AMPLIFIER, DVD PLAYER, CABLE OR
SATELLITE BOX, ETC.) COULD ALTER THE SIGNAL GROUNDING SCHEME
AND CAUSE HUM TO APPEAR IN YOUR PREVIOUSLY QUIET SYSTEM. IF YOU
ADD OR CHANGE AN UPSTREAM COMPONENT IN YOUR HOME THEATER
SYSTEM, YOU MAY NEED TO REVISIT THIS INPUT MODE SETTING ON THE
GOTHAM v2 SUBWOOFER FOR OPTIMUM NOISE PERFORMANCE. CABLE &
SATELLITE BOXES ARE PARTICULARLY TROUBLESOME IN THIS WAY.
IMPORTAN T
Master / Slave Switch
e Gotham v2s are designed to easily accommodate the implementation
of multiple subwoofers in your home theater system through a master/slave
connection chain. is method allows you to utilize the signal processing
features of one Gotham v2 to centrally control multiple Gotham v2s in the room.
Master/Slave functionality also makes it possible for the D.A.R.O. system to
optimize the response of a multiple subwoofer installation.
e Gotham v2 ships with this switch in the “Master” position. If you are
using a single Gotham v2 you will use the “Master” position and you need not
concern yourself with this section any further.
If your installation incorporates two or more Gotham v2s, you will designate
one Gotham v2 as the “Master” and all others in the system as “Slave” subwoofers
via the “Master/Slave” switch on the rear amplier panel of each Gotham v2.
LED’s on the front panel of the Gotham v2 are provided to indicate whether the
“Master” or “Slave” mode is selected for a given subwoofer.
From the Gotham v2 operating in “Master” mode, the “Output to Slave” signal
carries any signal processing selected on the Master Gotham v2 (including the
Master Level setting and D.A.R.O. processing) to further Gotham v2s operating
in “Slave” mode. “Slave” subwoofer signal processing and level controls will be
inoperable. In this mode, the user does not have to worry about level, crossover,
and other settings for the slave subwoofers.
Technical Notes:
• Selecting the “Slave” position defeats all user-denable signal processing and
the master level control. Because of this, there are some special situations
in which you may want to operate a single Gotham v2 in “Slave” mode. If
you are utilizing outboard signal processing and level-matching controls,
activating the “Slave” mode will prevent anyone from aecting system
parameters with the manual controls on the Gotham v2.
| Gotham v2Page 20
IMPORTAN T
IMPORTANT: PLEASE REFER TO THE “SYSTEM CONNECTION DIAGRAMS”
ON PAGES 22-25 FOR MORE INFORMATION ON USING THE INPUT /
OUTPUT CONNECTIONS.
“Output to Slave” Connector
If you are operating more than one Gotham v2 subwoofer in one home theater
system, you will designate one Gotham v2 as the Master (see page 20), and then
feed signal from it to the remaining “Slave” Gotham v2s via this balanced XLR
output. e “Output to Slave” cable can be connected to the “Le or Mono”
balanced XLR input on the next Gotham v2. When a Gotham v2 is in “Slave”
Mode, its “Output to Slave” connection can be used to pass signal to further
Gotham v2s operating in “Slave” mode.
e “Output to Slave” connector is designed to be used as follows:
1) From the “Master” Gotham v2’s “Output to Slave” connector to the rst
“Slave” Gotham v2’s “Le or Mono” XLR balanced input.
2) From the rst “Slave” Gotham v2’s “Output to Slave” connector to the
second “Slave” Gotham v2’s “Le or Mono” XLR balanced input.
3) From the second “Slave” Gotham v2’s “Output to Slave” connector to the
third “Slave” Gotham v2’s “Le or Mono” XLR balanced input. Etc, etc. (up
to ten Gotham v2s may be connected in this conguration). Appropriate
balanced cables with XLR terminations are available from your JL Audio
dealer and are not included with the Gotham v2.
Technical Notes:
• e “Output to Slave” signal carries any signal processing selected on
the Master Gotham v2 (including the Master Level setting and D.A.R.O.
processing) to further Gotham v2s operating in “Slave” mode.
• From Gotham v2s operating in “Slave” mode, the “Output to Slave” signal is
an exact, buered replica of the balanced input signal, making this method
of signal distribution preferable to using Y-adapters or splitters.
• Use only shielded, connection cables with high quality XLR connectors for
Master/Slave connection. Never use unbalanced cables with adaptors.
IEC-Style AC Power Connector
e IEC-style AC cord receptacle receives the heavy-gauge, 6 . (1.8 m)
long, power cord included with your Gotham v2 subwoofer. Gotham v2s sold in
dierent parts of the world are congured for each market’s electrical system and
include appropriate plugs on their power cords. Please note the voltage markings
next to the AC connector and make sure you are only powering your Gotham v2
from a receptacle that matches these markings. Do not use any AC power cord
other than the one supplied with the Gotham v2. For information about the Main
Fuse Holder, please see the Troubleshooting section of this manual.
e Gotham v2 subwoofer is a very powerful device and can draw a lot of
current. If too many components are connected with a Gotham v2 subwoofer to
one electrical outlet, you risk tripping a household circuit breaker during very
demanding program material. If this happens, split the Gotham v2 and other
components between two AC electrical circuits. For maximum performance,
dedicate an AC circuit to each Gotham v2. We suggest maximum circuit breaker
sizes of 120 VAC / 20 amps or 230 VAC / 10 amps.
Page 21 | Gotham v2
FRONT
PROCESSOR (BALANCED OUTPUTS)
FRONT
PRE OUT
REAR CENTER
L
REAR
R
SUB
OR
OUTPUTS
SYSTEM CONNECTION DIAGRAM 1:
One Gotham v2 to
Home Theater Receiver or
Home Theater Preamp/Processor
Most home theater receivers and
preamp/processors provide a single
(mono) subwoofer output. When
connecting a mono subwoofer output
to your Gotham v2, you will only use the
Gotham’s “Le or Mono” input.
Two connection types are available
for connecting the Gotham v2 to your
home theater system: balanced (XLR or
1/4-inch TRS connector) and unbalanced
(RCA-type connector). Balanced
connections provide superior noise
rejection and ensure proper grounding
between components. If your receiver or
processor has balanced outputs, we highly
recommend that you use them.
In the connection diagram at le,
balanced connections are shown as solid
lines, unbalanced connections are shown
dotted. You will only use one of these
input connection methods (not both).
GOTHAM REAR CONTROLS (MASTER)
WARNING! TURN OFF THE GOTHAM v2 AND ALL OTHER EQUIPMENT IN
THE SYSTEM BEFORE MAKING OR CHANGING ANY CONNECTIONS!
WARNING
| Gotham v2Page 22
SYSTEM CONNECTION DIAGRAM 2:
PROCESSOR (BALANCED OUTPUTS)
RECEIVER / PROCESSOR (UNBALANCED OUTPUTS)
Multiple Gotham v2s to
Home Theater Receiver or
Home Theater Preamp/Processor
To greatly simplify using multiple
subwoofers in a single home theater
system, Gotham v2s incorporate a
“Master/Slave” signal distribution system.
is allows control of all the Gotham v2s
in a system from a single “Master” unit.
First, you will select a Gotham v2
subwoofer as the “Master” via its upper
“Input Mode” switch. Generally, you will
designate the Gotham v2 closest to the
receiver/preamp as the master. In some
cases; for example, when the control panel
of certain units is dicult to access, you
may prefer to designate the one which is
easiest to access as the master.
Two connection types are available for
connecting the master Gotham v2 to your
home theater system: balanced (XLR or
1/4-inch TRS connector) and unbalanced
(RCA-type connector). Balanced
connections provide superior noise
rejection and ensure proper grounding
between components. If your receiver
or processor has balanced outputs, we
highly recommend that you use them to
connect to the Gotham v2 designated as
the master.
In the connection diagram at le,
balanced connections are shown as solid
lines, unbalanced connections are shown
dotted. You will only use one of these
input connection methods for the Gotham
v2 designated as the master (not both).
e remaining Gotham v2s in the
system will be congured as “Slave” units
via their upper “Input Mode” switches.
Using balanced XLR cables, you will
connect the master Gotham v2’s “Output
to Slave” to the “Le or Mono” balanced
input of the rst slave Gotham v2. at
slave unit’s “Output to Slave” connector
will feed the “Le or Mono” input of
the next slave unit via another balanced
XLR cable. Subsequent slave units will
be connected in the same manner.
FRONT
FRONT
PRE OUT
REAR CENTER
L
REAR
R
OUTPUTS
OR
SUB
GOTHAM REAR CONTROLS (MASTER)
IMPORTAN T
Connections between the “Master” and
“Slave” Gothams and between “Slave”
Gothams are via balanced XLR cables
ON LY.
WARNING
GOTHAM REAR CONTROLS (SLAVE)
TO ADDITIONAL GOTHAMS
(IF APPLICABLE)
WARNING! TURN OFF THE GOTHAM v2(s) AND ALL OTHER EQUIPMENT IN
THE SYSTEM BEFORE MAKING OR CHANGING ANY CONNECTIONS!
Page 23 | Gotham v2
STEREO ACTIVE CROSSOVER (BALANCED OUTPUTS)
LOW OUT
STEREO ACTIVE CROSSOVER (UNBALANCED OUTPUTS)
(SUB OUT)
LOW OUT
(SUB OUT)
OR
SYSTEM CONNECTION DIAGRAM 3:
One Gotham v2 in Mono to
Two-Channel Audio System
When connecting a Gotham v2 (or
RIGHTLEFT
multiple Gotham v2s) in mono to a two-
channel audio system you will use both
the “Le or Mono” and the “Right” inputs.
Summing circuitry in the Gotham v2’s
input section will sum the stereo signals
to mono.
We strongly recommend that you use
a high-quality active crossover, like the
JL Audio CR-1, to divide your
preamplier’s signals prior to connection
to the Gotham v2 and to the amplier
driving your main speakers. is will
allow you to lter low frequencies out of
the signals driving the main speakers,
resulting in better performance.
If you are not using an active crossover
and are comfortable running your main
speakers full-range, you can split your
preamplier’s output signals using
appropriate Y-connectors in place of the
active crossover shown in the diagram.
Two connection types are available
for connecting the Gotham v2 to your
two-channel audio system: balanced
(XLR or 1/4-inch TRS connector) and
unbalanced (RCA-type connector).
Balanced connections provide superior
noise rejection and ensure proper
grounding between components. If your
preamplier or active crossover oers
balanced outputs, we highly recommend
that you use them.
In the connection diagram at le,
balanced connections are shown as solid
lines, unbalanced connections are shown
dotted. You will only use one of these
input connection methods (not both).
NOTE: If desired, additional Gotham v2s
can be connected in “Slave” mode to the
Gotham v2 connected as shown on this
diagram. See “Connection Diagram 2” on
page 23 for slave connection explanation.
GOTHAM REAR CONTROLS (MASTER)
WARNING! TURN OFF THE GOTHAM v2 AND ALL OTHER EQUIPMENT IN
THE SYSTEM BEFORE MAKING OR CHANGING ANY CONNECTIONS!
WARNING
| Gotham v2Page 24
SYSTEM CONNECTION DIAGRAM 4:
STEREO ACTIVE CROSSOVER (BALANCED OUTPUTS)
STEREO ACTIVE CROSSOVER (UNBALANCED OUTPUTS)
Two Gotham v2s in Stereo to
Two-Channel Audio System
When connecting two Gotham v2s in
stereo to a two-channel audio system you
will only use the “Le or Mono” inputs of
each Gotham v2. e upper “Input Mode”
switch on each Gotham v2 will be set in
the “Master” position.
We strongly recommend that you use
a high-quality active crossover, like the
JL Audio CR-1, to divide your
preamplier’s signals prior to connection
to the Gotham v2 and to the amplier
driving your main speakers. is will
allow you to lter low frequencies out of
the signals driving the main speakers,
resulting in better performance.
If you are not using an active crossover
and are comfortable running your main
speakers full-range, you can split your
preamplier’s output signals using
appropriate Y-connectors in place of the
active crossover shown in the diagram.
Two connection types are available
for connecting the Gotham v2s to your
two-channel audio system: balanced
(XLR or 1/4-inch TRS connector) and
unbalanced (RCA-type connector).
Balanced connections provide superior
noise rejection and ensure proper
grounding between components. If your
preamplier or active crossover oers
balanced outputs, we highly recommend
that you use them.
In the connection diagram at right,
balanced connections are shown as solid
lines, unbalanced connections are shown
dotted. You will only use one of these
input connection methods (not both).
NOTE: If desired, additional Gotham v2s
can be connected in “Slave” mode to each
Gotham v2 connected as shown on this
diagram. See “Connection Diagram 2” on
page 23 for slave connection explanation.
LOW OUT
(SUB OUT)
OR
GOTHAM REAR CONTROLS (MASTER)
LOW OUT
(SUB OUT)
RIGHTLEFT
WARNING
WARNING! TURN OFF THE GOTHAM v2(s) AND ALL OTHER EQUIPMENT IN
THE SYSTEM BEFORE MAKING OR CHANGING ANY CONNECTIONS!
Page 25 | Gotham v2
RECOMMENDED SETUP PROCEDURES
1) Preparation for Setup Process: ..................................... 26-27
2) Level Setting: ....................................................... 28
3) Polarity/Phase Adjustment: ........................................... 28
4) Experiment with Location: ........................................... 28
5) Apply D.A.R.O: .................................................. 29-30
6) Adjust E.L.F. Trim: .................................................. 30
PREPARATION FOR SETUP PROCESS:
Please conrm the following system settings before beginning the setup
process. is will ensure a neutral starting point and an eective setup of your
subwoofer system.
On your Home Theater Receiver or Preamp/Processor:
Before beginning setup of your Gotham v2 subwoofer system we recommend
that you set your receiver or preamp/processor as follows (please turn o all
Gotham v2s in the system via their front panel power switches prior to making
these adjustments):
1. Speaker Size
In the speaker setup menu of your receiver or preamp/processor, set up all of
your high-frequency speakers as “small” with a crossover point of 80 Hz. is
will send ALL bass to the Gotham v2(s).
2. Speaker Distance
In the speaker setup menu, properly set all speaker distances to the primary
listening seat, including the subwoofer’s distance. Use a tape measure to
determine these distances (time coherence is important.) If multiple Gotham
v2s are being used, average their distances to the primary listening seat and
use that number to set the subwoofer distance.
3. Subwoofer Level
Set the subwoofer level in the receiver or preamp/processor to “0” or its middle
position.
4. Tone Controls / Equalizers
Set all tone controls to “0” and defeat all equalizer features.
On your Active Crossover or Bass Management Processor:
If you are using an active crossover or bass-management processor, we
recommend that you set it as follows before beginning setup of your Gotham v2
subwoofer system (please turn o all Gotham v2s in the system prior to making
these adjustments):
1. Low-Pass Filter Frequency
Select a low-pass lter frequency of 80 Hz (24 dB/octave slope)
2. High-Pass Filter Frequency
Select a high-pass lter frequency of 80 Hz (24 dB/octave slope)
3. Low-Pass (Subwoofer) Output Level
Set the subwoofer output level to “0” or its middle position.
| Gotham v2Page 26
max
On the Gotham v2’s Front Panel:
Please turn o the home theater receiver or preamp/processor to make
these adjustments.
1. “Power” Switch
Flip each Gotham v2’s “Power” switch to the “On” position.
2. “Lights” Switch
Flip each Gotham v2’s “Lights” switch to the “On” position. If you don’t see any
lights on the front panel, you may have forgotten to plug the Gotham v2 in or
there may be a problem with the electrical circuit.
3. “Input Mode” Indicator Lights
If you are using a single Gotham v2, conrm that its “Input Mode” indicator
light is on the “Master” position. If not, you will need to access the le “Input
Mode” switch on the rear panel of the Gotham v2.
If you are using multiple Gotham v2s in a Master/Slave conguration, conrm
that the unit connected directly to your receiver or preamp/processor is
indicating “Master” on its “Input Mode” lights and that all other units are
indicating “Slave” on their “Input Mode” lights. If not, you will need to access
the le “Input Mode” switches on the rear panels of the Gotham v2s.
4. “Level Mode” Switch
Flip the master Gotham v2’s “Level Mode” switch to the “REF” position.
5. “LP Filter” Switch
If your home theater receiver/processor is handling bass management
(speakers set on “small”) or if you are using an outboard crossover/bassmanagement processor, ip the master Gotham v2’s “LP Filter” switch to
“OFF.” If not, select the “12 dB” position.
6. “LP Freq. (Hz)” Knob
Rotate the “LP Freq.” knob to the “80 Hz” position.
7. “e.l.f. trim (dB)” Knob
Rotate the “e.l.f. trim” knob to “0”
8. “Polarity” Switch
Flip the “Polarity” switch to “0”.
9. “phase (deg.)” Knob
Rotate the “phase” knob to “0” degrees
10. D.A.R.O. Defeat Switch
Press the D.A.R.O. defeat switch so that the red light in the
switch remains lit.
Page 27 | Gotham v2
RECOMMENDED SETUP PROCEDURES (continued)
Subwoofer System Setup:
Once you have set the controls on your home theater receiver or preamp/
processor and on your Gotham v2(s) to the settings recommended on pages
26 and 27, you are ready to begin setting up your Gotham v2 for optimum
performance.
1) Level Setting
Using familiar music or movie material with deep bass content, adjust the
subwoofer level to blend with the other speakers using your receiver or preamp/
processor’s subwoofer level control. is method is more immune to tampering
than using the Gotham v2’s “Master Level” knob (think toddlers or curious
visitors).
In the unlikely event that the subwoofer level control in your receiver or
preamp/processor cannot be turned up enough to level match the Gotham v2,
return that control to “0”. en, ip the Gotham v2’s “Level Mode” switch to
“Variable” and with “0” as your reference point (REF mode gain and Variable “0”
gain are identical) use the “Master Level” control to level match the subwoofer
with the other speakers. MAKE NOTE OF THIS SETTING FOR FUTURE USE.
For more detailed information on your Gotham v2’s level setting controls, please
refer to the “Level Mode” and “Master Level” sections on pages 15 - 16 of this manual.
2) Polarity and Phase Adjustment
It is oen helpful to have a second person operating these controls so that you
can easily hear the changes from the primary listening seat.
Listening to familiar source material (preferably music with good upper bass
and midbass response), ip the “Polarity” switch from “0” to “180” and listen for
dierences. e correct setting will sound most natural with the best upper bass
punch and articulation. If both sound similar, choose “0”.
Once Polarity is set, use the same music material to audition dierent “Phase”
control settings and choose the one that further enhances the upper and midbass
response. If you can’t hear a dierence, set the control to “0.”
3) Experiment with alternative subwoofer locations (if necessary).
If you are satised with the basic performance of your subwoofer you are ready
to move on to the next step. If not, we recommend that you experiment with
the position of your subwoofer until you are pleased with its basic performance.
Experimentating with placement is KEY to a superior sounding system. Moving the
subwoofer just a few feet can have a signicant eect on the smoothness of the bass.
For each new position, start with the polarity and phase controls at “0” and repeat the
setup process beginnng with Step 1.
IMPORTANT! WRITE DOWN ALL SETTINGS PERFORMED IN STEPS 1-3 FOR
FUTURE REFERENCE.
IMPORTAN T
| Gotham v2Page 28
IMPORTAN T
IMPORTANT! MAKE SURE THE ROOM IS QUIET DURING D.A.R.O.
CALIBRATION! TURN OFF ANY NOISY APPLIANCES NEAR THE LISTENING
ROOM (DISHWASHERS, WASHING MACHINES, ETC.)
IT IS PARTICULARLY IMPORTANT TO TURN OFF AIR CONDITIONERS OR HEAT
PUMPS DURING CALIBRATION. THESE FORCED-AIR-TYPE HVAC SYSTEMS
CAN CREATE MODERATE LEVELS OF 15 – 20 HZ NOISE THAT MAY INTERFERE
WITH CALIBRATION.
4) Applying Digital Automatic Room Optimization (D.A.R.O.)
You are now ready to apply the power of JL Audio’s exclusive Digital Automatic
Room Optimization (D.A.R.O.) system. is system will measure the response of
the subwoofer at your primary listening seat and apply a powerful 18-band equalizer
to tame the peaks caused by room modes, resulting in smoother, more accurate bass
performance. If you are using multiple Gotham v2s in a master/slave conguration,
you will only need to address the unit designated as “master” to perform D.A.R.O.
calibration for the entire subwoofer system. Note that all front-panel signal
processing is defeated during D.A.R.O. calibration, regardless of the knob settings.
Normal operation is restored once calibration is complete.
a) Set the Main Power switch to the “ON” position and be sure the Gotham v2’s
indicator lights are switched “ON” via the “Lights” switch.
b) Remove the calibration microphone from its protective pouch and connect its
cable to the mini-XLR jack on the Gotham v2’s front control panel.
NOTE: D.A.R.O. Calibration is only possible when the included JL Audio test
microphone is plugged in to the Gotham v2 front panel. e “Calibrate” feature is
disabled with no microphone plugged in to prevent accidental loss of settings.
c) Connect the microphone to the other end of the mic cable and temporarily place
the mic in the primary listening seat. If you have a microphone stand, you can
place the microphone at head height and position in the primary listening seat.
d) On the Gotham v2’s control panel, press the “Calibrate” button. e green light
on the “Calibrate” button will ash slowly, indicating that calibration will begin
in 5 seconds.
e) Within 5 seconds of pressing the “Calibrate” button, return to your primary
listening seat and hold the microphone in your normal, seated head position at the
approximate height of your ears.
f) A noise sequence will be played through the Gotham v2 that sounds like hashy
static. e sequence will last approximately 3 minutes. During this process, the
D.A.R.O. system is taking a frequency response measurement at your seat and
correcting the problems it nds. e D.A.R.O. system also compensates for
any before & aer level dierences so that your Gotham v2 will have a similar
perceived loudness aer the calibration process. When D.A.R.O. is nished
calibrating, the “Calibrate” button will light and stay on, indicating a successful
calibration.
Should you wish to run a new calibration, simply repeat the steps above.
Page 29 | Gotham v2
To clear the D.A.R.O.’s settings (i.e., return them to at) & turn o the
Calibrate light, press and hold the Demo button and then press the Defeat button.
Please note that you must perform this button sequence quickly. If you hold the
Demo button for more than 2 seconds without touching the Defeat button, the
Demo tones will start. Should this happen, simply wait for the Demo sequence
to end and try again. You can perform a new calibration by following the normal
procedure outlined above.
IMPORTANT! IF YOU MOVE YOUR Gotham v2 OR PRIMARY LISTENING
SEAT IN THE FUTURE, YOU WILL NEED TO RUN D.A.R.O. AGAIN. ANY
PARTICULAR CALIBRATION IS UNIQUE TO THAT PARTICULAR SUBWOOFER
POSITION AND LISTENING SEAT POSITION COMBINATION. SIMPLY
FOLLOW THE STEPS ABOVE TO CREATE A NEW CALIBRATION CURVE.
5) Extreme Low Frequency (e.l.f.) Trim
Use the “e.l.f. trim” control to adjust the extreme low bass extension of the
Gotham v2. is control allows -12 dB of cut or +3 dB of boost at 24 Hertz and is
particularly useful when using a Gotham v2 (or two) in a small to medium sized
home theater. Since smaller enclosed spaces help to boost the level of the lowest bass
frequencies, smaller theaters can be overwhelmed by the strong low-bass output of
the Gotham v2 subwoofer. is can create a “thick” or “bloated” character in the
lower bass region. Turning down the “e.l.f. trim” knob cuts the extreme low bass
level and alleviates this condition. Feel free to experiment and listen to a variety of
demanding material until you nd the best match for your room and your tastes.
IMPORTAN T
Your Gotham v2 is now optimized for maximum bass performance at your
listening seat. Congratulations!
| Gotham v2Page 30
FREQUENTLY ASKED QUESTIONS
Can I place objects on my subwoofer?
We do not recommend placing any items on the subwoofer cabinet as they may
vibrate, causing undesirable noise and possible damage to the nish. Under no
circumstances should any object containing liquid be placed on the Gotham v2
cabinet.
Is the Gotham v2 magnetically shielded?
Gotham v2 subwoofers are not magnetically shielded. To avoid magnetic
distortion with certain television types, place the Gotham v2 at least 3-4 feet (1 -
1.5m) from your screen. If you notice any discoloration in the picture, try moving
the subwoofer further away until these artifacts disappear.
Will my electric bill be high if I leave the Gotham v2 in “Auto” mode?
When in “Auto” mode, the Gotham v2 amplier is only powered up when
a signicant signal is detected on the inputs. When powered down, only
“housekeeping” circuits remain on, which draw negligible amounts of power
from the wall (less than 5 watts).
Should I unplug my subwoofer during a thunderstorm or extended absence?
YES. You should unplug your Gotham v2 during (or before) thunderstorms. is
will prevent any possible damage from voltage spikes due to lightning. In these
conditions, it’s a good idea to unplug all of your audio / video components. If you
are going to be away from home for several days, it is also a good idea to unplug
your home theater components to prevent damage from unexpected storms or
power line conditions.
CLEANING YOUR GOTHAM v2
Dust your Gotham v2’s subwoofer cabinet using a clean, so microber cloth
or feather duster. Microber cloths are commonly available where automotive
detailing supplies are sold.
Light smudges can generally be wiped o with a clean microber cloth. For more
stubborn smudges, polish and protect the nish using a high-quality automotive
wax and a microber cloth, both available wherever automotive detailing supplies
are sold. We recommend Meguiar’s® “NXT Tech Wax” and Meguiar’s® Microber
Detailing cloths.
Never use a polish that contains harsh solvents or abrasives as these may
permanently damage the nish. Never use furniture polish or any oil-based
product on your Gotham v2. Never use solvents or aggressive cleaning agents on
your Gotham v2. When in doubt, test the cleaning product on the underside of
the cabinet and let it sit for several days before committing to its use on visible
portions of the cabinet.
Page 31 | Gotham v2
TROUBLESHOOTING
No sound from subwoofer.
1. Verify that Gotham v2 is plugged in, turned “ON” & that front panel lights are
“ON”. If the lights do not turn on, check the circuit breaker that feeds its outlet or
plug the Gotham v2 into another AC power outlet. If your AC outlet has power but
the lights still do not come on, you may need to inspect/replace the Gotham v2’s
main power fuse. Refer to the “Main Fuse Holder” section on the next page.
3. Test the subwoofer by pressing the DEMO button on the front panel – if the sub
emits demo tones the subwoofer’s internal circuitry is ne and an input problem
is likely. Check the input cable connections at the Gotham v2 and at the receiver/
preamp/processor.
4. Verify that your receiver’s subwoofer settings have not changed.
5. If your other speakers play, but the Gotham v2 does not, try changing the cable that
connects the Gotham v2 to the system.
6. If the problem persists, call your dealer or JL Audio Technical Support
for assistance.
e bass level has changed.
1. Make sure your level settings (on the Gotham v2 and in your receiver/preamp/
processor) have not changed.
2. If you are using the Gotham v2’s “Master Level” knob to set the subwoofer level,
conrm that the “Level Mode” switch is set to “Variable”.
3. Verify the position of the ELF Trim knob.
Hums or other unusual noises from your Gotham v2
1. See Input Mode discussion on page 20 of this manual, especially if any upstream
components, cables, etc., have recently changed.
2. Turn o the Gotham v2, disconnect all its input and output signal cables, turn the
Gotham v2 back on. If the noise disappears, the noise is being caused elsewhere in
your system.
Bass sounds “muddy” or “too heavy”.
1. Try decreasing the 24 Hertz level using the “e.l.f. trim” control. Muddy bass
can sometimes be caused by too much low frequency output in a moderately
sized room.
2. Decrease the overall subwoofer level.
3. Verify your receiver’s subwoofer settings.
4. Try a dierent subwoofer or main listening seat location. Changing one or the
other can have a HUGE e ect on how your system sounds. See the placement
discussion on pages 6-10 of this manual.
| Gotham v2Page 32
TROUBLESHOOTING - continued
D.A.R.O. Calibration attempt gives blinking Calibrate light
1. If the included JL Audio Microphone is not properly plugged into the front panel
jack, calibration will fail and the green Calibrate light will blink fast. Calibration
will ONLY proceed with the JL Audio microphone connected. Connecting any
other mic will cause the calibration to fail. Cancel the blinking Calibrate light by
pressing the Calibrate button again.
2. If calibration fails with the JL Audio microphone properly connected,
the green Calibrate light will blink slowly. Test the microphone and
cable connections and try running calibration again. If calibration
fails aer following the steps above, the microphone or microphone
cable may be bad. Contact JL Audio Home Technical Support.
Your Gotham v2 is clearly audible outside of your house.
1. Revisit the “Master Level” setting on your Gotham v2(s) or your home theater
receiver/preamp/processor.
2. Inquire with your JL Audio dealer about noise isolation strategies.
3. Move the Gotham v2 away from windows.
MAIN FUSE HOLDER
Located on the rear panel, next to the AC cord receptacle is the main fuse holder’s
cover. is small spring-loaded cap may be removed, allowing access to inspect
or replace the main power fuse. If your AC outlet has power but the Gotham v2’s
lights do not come on, the main power fuse may be blown.
To Remo ve - Unplug the subwoofer’s AC power cord. Insert a small athead
screwdriver into the cap’s slot and turn counter-clockwise slowly until the fuse holder
is released. Once removed, the fuse can be inspected and if necessary, replaced. Refer
to the chart below for fuse values for your specic Gotham v2 model.
To Reinstall - Note that the fuse holder’s body is keyed to the opening and must
be aligned to t properly. Insert the fuse holder into the opening and gently turn
clockwise (about 1/8 turn) to lock in place. Pressing the cap and feeling for the spring
to compress will help to locate the correct position. Reconnect the AC power cord.
If the replacement fuse blows immediately aer a fuse replacement,
the subwoofer’s amplier may require service. Please contact your JL Audio
Authorized Retailer or Distributor.
Fuse Ratings, 120V Models Only
Model Fuse Ty pe Fuse Size
g213 (120 V) 0.25 x 1.25-inch, fast-acting 15A , 250V
Fuse Ratings, 240V Models Only
Model Fus e Type Fuse Size
g213 (240V) 5mm x 20mm, fast-acting 10A, 250V
Page 33 | Gotham v2
FRONT
SIDE WITH GRILLE BACK
H
BOTTOMTOP
W
D
Specifications
Enclosure Type: Sealed, with non-parallel walls
Driver: Twin 13.5-inch (nominal diameter)
Frequency Response (anechoic):
Effective Piston Area:
Effective Displacement: 773 cu. in. (12.7 liters)
Amplifier Power: 4500 watts RMS sh ort-term
Dimensions: (H) Height x (W) Width x (D) Depth
Height Dimensions include feet.
Net Weight: 360 lbs. (163 kg)
Cabinet Finish:
g213v2
gotham home subwoofer
19-112 Hz (±1.5dB)
–3 dB at 17. 5 Hz / 120 Hz
–10 dB at 14 Hz / 150 H z
214.70 (0.1386 s q. m)
34.13 in x 21.50 in. x 24.00 in .
867 mm x 546 mm x 610 mm
High-Gloss Black
FE ATURES
Unbalanced Inputs:
Stereo or Mono (two RCA jacks)
Balanced Inputs:
Stereo or Mono (two female XLR jacks)
Output To Slave:
Balanced (one male XLR jack)
Input Modes:
Master or Slave
Level Modes:
Reference (xed gain) or Variable from
full mute to +15dB over reference gain
Power Modes:
O, On or Automatic Signal-Sensing
Light Modes:
O, On or Dim
Low Pass Filter Mode:
O, 12 dB per octave or 24 dB per octave
Low Pass Filter Cuto Frequency:
Variable from 30 Hz – 130 Hz
Polarity:
0 or 180 degrees
Phase:
Variable from 0 – 270 degrees
E.L.F. Trim:
Variable from –12 dB to +3 dB at 24 Hz
Digital Automatic Room Optimization
(D.A.R.O.)
Automatic, 18-band digital equalizer with
included laboratory-grade calibration
microphone, defeatable.
| Gotham v2Page 34
LIMITED WARRANTY / SERVICE INFORMATION
JL AUDIO warrants this product to be free of defects in materials and
workmanship for a period of three (3) years from the original date of purchase.
Damage caused by the following is not covered under warranty: accident,
misuse, abuse, product modication or neglect, failure to follow installation
instructions, unauthorized repair attempts, misrepresentations by the seller. is
warranty does not cover incidental or consequential damages and does not cover
the cost of removing or reinstalling the unit(s) or shipping the unit(s) to JL Audio
for service. Cosmetic damage due to accident or normal wear and tear is not
covered under warranty.
is warranty is not transferable and applies only to the original purchaser
of the product from an authorized JL AUDIO dealer. Warranty is voided if the
factory-applied product serial number is removed or defaced.
Should service be necessary under this warranty for any reason due to
manufacturing defect or malfunction, JL AUDIO will, at its discretion, repair or
replace the defective product with new or remanufactured product at no charge.
Any applicable implied warranties are limited in duration to the period of
the express warranty as provided herein beginning with the date of the original
purchase at retail, and no warranties, whether express or implied, shall apply
to this product thereaer. Some states do not allow limitations on implied
warranties, therefore these exclusions may not apply to you. is warranty gives
you specic legal rights, and you may also have other rights which vary from
state to state.
WARNING
WARNING: THIS PRODUCT CONTAINS NO USERSERVICEABLE PARTS.
PRODUC T IN WHICH DISASSEMBLY, REPAIR AND/OR MODIFICATION HAS
BEEN ATTEMPTED BY UNAUTHORIZED PARTIES WILL NOT BE COVERED
UNDER WARRANTY.
If you need service on your JL AUDIO product:
All warranty returns should be sent to JL AUDIO freight prepaid through
an authorized JL AUDIO dealer and must be accompanied by proof of purchase
(a copy of the original sales receipt). Direct returns from consumers or nonauthorized dealers will be refused unless specically authorized by JL AUDIO
with a valid return authorization number. Warranty expiration on products
returned without proof of purchase will be determined from the manufacturing
date code. Coverage may be invalidated as this date is previous to purchase date.
Return only defective components. Non-defective items received will be returned
freight-collect. Customer is responsible for shipping charges and insurance in
sending the product to JL AUDIO. Freight damage on returns is not covered
under warranty. Always include proof of purchase (sales receipt).
For Service Information in the U.S.A. please call:
JL Audio customer service:
(954) 443-1100 during normal business hours (Eastern Time)
JL Audio, Inc • 10369 North Commerce Parkway, Miramar, FL 33025
International Warranties:
Products purchased outside the United States of America are covered only by that
country’s distributor and not by JL Audio, Inc.
Page 35 | Gotham v2
HOME AUDIO | MOBILE AUDIO | MARINE AUDIO
“JL Audio”, “Gotham” and the JL Audio logo are registered trademarks of
JL Audio, Inc., “Ahead of the Curve” is a trademark of JL Audio, Inc. Due to
continuous product development, all specifications are subject to change
without notice.
Printed in USA • ©2015 JL Audio, Inc. • U.S. PATENTS: #5,734,734 #5,949,898
#6,118,884 #6,229,902 #6,243,479 #6,294,959 #6,501,844 #6,496,590
#6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other
U.S. & Foreign patents pending. For more detailed information please visit us
online at www.jlaudio.com.
SKU-011435-11 -2015
www.jlaudio.com
North Commerce Parkway • Miramar, Florida • • USA
Loading...