RemoteMix 3.5
Broadcast Field Mixer
User Guide
™
JK Audio
Welcome
Thank You
Thank you for purchasing a JK Audio RemoteMix 3.5 Broadcast Field Mixer.
Please read this guide for instructions on setting up and using your new product.
Getting Assistance
If you have technical or application questions:
In the US & Canada, call us toll free at: 800-552-8346
All other countries dial: 815-786-2929 (M-F 8:30-5:00pm Central Time Zone)
Email us at: support@jkaudio.com
Or, check out our FAQ section for answers to common questions.
Limited Warranty
The RemoteMix 3.5 is covered by a 2 year warranty to be free from defective
workmanship and materials. To obtain service, contact JK Audio by phone or
email for return authorization. Once authorized, you will carefully pack and ship
the faulty product and all accessories to us. You will pay for shipping to us and
we will pay for return back to you.
This warranty does not cover damages due to accident, weather, re, ood,
earthquake, misuse, unauthorized repairs or modications, or damages occurred
in shipping, only defective workmanship or materials.
There are no expressed or implied warranties which extend beyond the
warranty here made.
ii
RemoteMix 3.5™ Broadcast Field Mixer
Contents
Overview 1
Getting to know your RemoteMix 3.5™
2 Controls & Indicators
4 Inputs & Outputs
Getting Connected
Setting Up
Making a Call
Operation 7
Bluetooth Wireless Technology
8 Status LED, Pairing
9 Reconnecting, and Disconnecting
FAQs 10
2
6
8
Technical Information 12
Contents
iii
Features
HD Voice (Wide-Band Speech)*
Three XLR Mic Jacks
Three ¼” Headphone Jacks with
Individual Level Controls
3.5 mm Send and Receive Jacks
LED VU Meter
Phone Line Hybrid with DTMF Keypad
Universal PBX Handset Interface
Wired Phone Headset Interface
(2.5mm & 3.5mm Interfaces)
Bluetooth Wireless Technology
Dual 9 Volt Batteries
100-240 VAC External AC
Power Supply
In the Box
Universal Power supply with
detachable cord
2.5 mm 3-conductor Wireless
Interface Cable
3.5 mm 4-conductor Wireless
Interface Cable
* HD Voice. While standard phone calls have a narrow bandwidth of 300 Hz to 3.4 kHz, HD
Voice calls offer 50 Hz to 7 kHz bandwidth. The additional 1.5 octaves on the low end gives
voice a more natural sound, while the additional upper octave dramatically improves speech
clarity and intelligibility.
Wireless HD Calls. To take advantage of this extended bandwidth, both phones on the call
must support HD Voice, and both phones must be on the same carrier, in coverage areas
that support HD Voice.
18” RJ22 Modular Handset Cord
60” RJ11 Phone Cord
7 kHz
iv
RemoteMix 3.5™ Broadcast Field Mixer
Overview
Introducing the RemoteMix 3.5™
JK Audio introduces RemoteMix 3.5, a three-channel eld mixer and headphone
amplier. More than just a eld mixer, this is a universal communications
interface. RemoteMix 3.5 features a phone line hybrid and keypad, a PBX
handset interface, and both wired and wireless cell phone interfaces. These parts
were designed to work together, saving setup time in the eld.
Radio – RemoteMix 3.5™ is perfect for sports remotes. Use it as a phone line
hybrid, calling into your studio talk show hybrid. Use it as a front-end mixer for
your POTS, ISDN, IP or smart phone codec.
TV – RemoteMix 3.5™ gives you the ultimate phone connectivity with three ¼”
IFB headphone feeds. Send and receive interview audio and pull IFB out of any
business phone system, even your cell phone or notebook.
Great Sound – A soft limiter prevents overdriving the phone line interfaces, while
the mixer XLR output is pre-limiter (full range). Convenient 3.5mm send and
receive jacks for recording the show, or mixing in your MP3 player.
Bluetooth Wireless Technology – Route audio through your cell phone or
notebook using Bluetooth Wireless Technology. RemoteMix 3.5 will connect in
Hands-Free mode allowing a two-way 3.4 kHz telecom bandwidth connection.
RemoteMix 3.5 can also connect in A2DP mode offering a 20 kHz audio
bandwidth, listen-only connection.
Overview
1
Getting to Know Your RemoteMix 3.5
2 3 41
5
Controls & Indicators
1. Mic Level Controls
Each of the three XLR inputs has a level control knob with a separate red
<Peak> LED to indicate clipping on each channel. If you see more than an
occasional ash of the <Peak> LED you should decrease the level for that
channel.
6 7 1110
9
8
2. Master Level Control
The <Master> control knob will set the overall level of the sum of all the mic
and line inputs. The LED meter for the master audio level ranges from -30
dB to +3 dB.
3. Keypad
The telephone keypad provides DTMF tone dialing. You may use the
keypad at anytime during a call but keep in mind that both transmit and
receive telephone audio are muted during a keypress.
4. Redial
Press this button to instantly redial the last telephone number that was
keyed in.
5. Headphone Controls
Each of the three headphone outputs has a separate level control so each
listener can adjust their audio level independently.
2
RemoteMix 3.5™ Broadcast Field Mixer
Getting to Know Your RemoteMix 3.5
Controls & Indicators Cont’d
6
6. Cue Control
The <Cue> input control adjusts the signal going to the headphones
from the 1/4” <Cue Input>. When using the 1/4” Cue Input Wireless
Interface, the individual headphone level control adjusts the overall level
of your headphones while the <Cue> input control adjusts the level of the
person on the other side of the call in all headphones. You should keep
in mind that your wireless telephone also has level control. If you are
having level problems that cannot be corrected with the controls on the
RemoteMix 3.5, try adjusting the level on the wireless telephone itself.
7. Bluetooth Wireless Technology
7
This switch activates the Bluetooth Wireless Technology. The blue LED
directly above this switch indicates when it is on.
8. Keypad Switch
8
This switch disables the DTMF keypad to prevent unwanted tones from
being transmitted down the phone line during a broadcast.
9. Ringer
9
RemoteMix 3.5 does not have an audible ringer but there is a visual ring
indicator that will ash for incoming calls. This red LED is located directly
below the keypad.
10
10. Phone Line Switch
When using the RJ-11 analog phone jack, this switch acts as the switch-
hook for the telephone line. The On Hook position is when you are not
using the line or you are waiting for a call. When you want to place a call,
or when a call comes in, switch to the Dial/Talk position.
11
11. Power
This is the main power switch that turns the unit on. Whenever the power
is turned on, the red LED above this switch will be lit. The green <AC>
LED will be lit whenever a live AC power source is connected, even if the
main power switch is off.
Controls & Indicators
3
Getting to Know Your RemoteMix 3.5
Inputs & Outputs
1. Mic Inputs 1 and 2
Balanced XLR jacks with low-noise pre-ampliers.
124 35
67 8 9
2. Mic Input 3
Balanced XLR jacks with low-noise pre-ampliers. A <Mic/Line> selector
switch adds a 40 dB pad for a line level balanced input.
3. Stereo 3.5 mm Line Level Input
The stereo 3.5 mm line level input can be used instead of or in addition to
the channel 3 XLR input. You can connect either a mono or stereo signal to
this mini jack. If you use a stereo input, both channels will immediately be
summed together. Then the audio from the mini jack and the XLR would be
added together and treated as one mono signal on channel 3
4. Stereo 3.5mm Line Level Output
Can be connected to your mini disk or other recording device. The <Master
Output> will be on the Left channel and the Receive mix from the phone
line and/or <Cue input> on the Right channel.
5. The Master Output
A balanced XLR jack that contains the sum of all three input XLRs and the
3.5 mm input. This audio signal has a full 20 Hz to 20 kHz bandwidth.
6. Headphone Jacks
Headphone output is a mix of local mic and line inputs including the return
from the phone line.
4
RemoteMix 3.5™ Broadcast Field Mixer
Getting to Know Your RemoteMix 3.5
Phone Line Connection
7. Phone Line
The RemoteMix 3.5 has an RJ-11 jack that can be connected to any
standard, single line analog telephone line. This jack should not be
connected directly to digital PBX or ISDN phone systems.
8. Handset Interface
If you do not have access to an analog phone line or if the phone system
is a digital or analog PBX, ISDN, VOIP or a key telephone system, you
can use the built-in handset interface. Disconnect the telephone handset
from the coily cord and plug the cord into the RemoteMix 3.5 <Universal
Handset Interface> jack. Now select the handset type on the 3 position
switch.
Trial and error works faster than a chart of handset types, but this basic
description may help.
Switch Position Handset Microphone Type
A Electret
B Dynamic
C Carbon
9. Cue Input / Wireless Phone Interface
RemoteMix 3.5 comes equipped with a <Wireless Phone Interface> built
in to the 1/4” <Cue Input>. This 1/4” wireless interface accepts a specially
designed 1/4” to 2.5 mm or 1/4” to 3.5mm cable provided with the unit.
This interface works with any wireless phone or notebook that accepts
standard third party headsets and earpieces. Some wireless phones have
the standard 2.5 mm TRS jack while others have a 3.5 mm TRRS jack and
others yet have proprietary jacks. Adapters to convert the proprietary jack
to a standard 3-conductor 2.5 mm or 4-conductor 3.5 mm jack are available
for most wireless telephones through their dealers, local electronic stores or
many internet stores.
10. When using the wireless interface, it is important to keep your wireless
telephone 12” - 24” away from the RemoteMix 3.5 and any microphone or
headphone cables. This will help prevent unwanted RF noise from entering
the unit.
Inputs & Outputs
5
Getting Connected
Setting Up
1. Connect your audio equipment, microphones, cue input, and headphones to
the input and output jacks on RemoteMix 3.5.
2. There are 4 ways to connect the RemoteMix 3.5 to the phone line:
A. For Analog Phones: Connect the jack marked <Phone Line> to any
standard analog telephone line, or
B. If there is no access to an Analog Phone Line: Disconnect the
handset on an existing telephone and plug the coily cord from the
phone into the <Universal Handset Interface> jack on RemoteMix 3.5,
or
C. If there is no Land Line: Connect the <Wireless Phone Interface>
jack to the headset jack on your cellular telephone using the supplied
JK Audio interface cable.
The 1/4” Wireless Interface jack also serves as a <Cue Input> that
feeds the headphones. Connect any line level output here, such as the
output from your personal audio player. This signal does not reach the
XLR output but will be present on the right channel (return) of the
stereo output.
D. Bluetooth Wireless Technology. See page 8.
Making a Call
There are also 3 ways to initiate an outbound call with the RemoteMix 3.5. First
turn on the power switch and ip the <Phone Line> switch to Dial/Talk.
A. When connected to an analog line: Flip the <Keypad> switch to
On and dial your call. You are now ready to broadcast or record a
telephone interview.
B. When connected via the Universal Handset Interface on the
RemoteMix 3.5: Take the handset off of the cradle of the phone you are
connected to and dial with the keypad on the base of that phone. The
handset must stay off-hook for the duration of the broadcast or the call
will be disconnected.
C. When connected via the 1/4” Cue Input / Wireless Phone Interface:
Dial the call with your cellular phone handset. Audio will automatically
be transmitted and received through the RemoteMix 3.5 audio inputs
and outputs. The phone’s internal speaker and microphone will be
disabled during the call. Feel free to leave your phone connected to
power throughout the broadcast to conserve battery power.
6
RemoteMix 3.5™ Broadcast Field Mixer
Operation
IFB
If using the phone line or handset interface for an IFB feed, the balanced male
XLR output may be used to feed an IFB earpiece or other device. If using the
1/4” cue input / wireless adapter jack for the telephone connection, the IFB feed
must be taken from one of the 1/4” headphone jacks. This also applies if you are
planning to record both sides of the conversation while using the 1/4” wireless
adapter jack for the telephone connection.
Power
RemoteMix 3.5 is powered by two 9 volt alkaline batteries located on the side of
the unit. The red <Power> LED on the front of the device will gradually dim as
the battery runs down, then extinguish about a half hour before the unit shuts
down. Since these two batteries are in separate drawers and wired in parallel,
you can hot swap one battery at a time so you never lose power.
It is important to replace both at the same time with identical batteries. If two
fresh batteries are not available, it is better to run using only one good battery.
Since the battery xtures are wired in parallel, it does not matter which one gets
the single battery.
We also provide a high quality, regulated AC to DC adapter to power
RemoteMix 3.5 when AC power is available. Simply plug it into the back of
RemoteMix 3.5 and plug the transformer into a wall outlet. This is a switching
power supply so you can connect to a 110 or 220 VAC power source. When the
power connector is inserted into the jack, the batteries are bypassed. The
adapter does not charge the batteries. If you lose power during your broadcast,
the RemoteMix 3.5 automatically reverts to battery power so your broadcast will
not be interrupted.
Make sure you use only the supplied AC power adapter with the
RemoteMix 3.5. Using any other adapter could damage the unit.
AC
W
ARNING! It is strongly recommended that this product be connected
to an adequate surge protection device for the power line as well as the
telephone line at all times.
Operation
7
Bluetooth Wireless Technology
Bluetooth Status LED
The blue LED on the front of the unit ashes in different sequences to indicate
the current connection status. When attempting to put the unit into Idle or
Pairing mode, you should power the unit off then back on before pressing
the < > switch. If you put the unit into the wrong state due to releasing the
< > switch at the wrong time, holding the < > switch for "X" seconds will not
put it into the desired mode.
Pairing Mode
In Pairing Mode, any Bluetooth wireless technlogy enabled device within
range can pair with your RemoteMix 3.5. To put the unit in Pairing Mode,
pull up the < > switch for 5 seconds while the unit is on. The blue LED will
ash rapidly at a rate of 100ms off, 100ms on. Once the pairing process is
complete the unique device ID is stored in Connection History. Subsequent
connections can be made automatically from Idle Mode.
Idle Mode
In Idle Mode, RemoteMix 3.5 searches for paired devices. To put the unit in
Idle Mode, pull up the < > switch for 2 sec when the unit is on. The blue
LED will ash at a rate of 2 secs off, 200ms on.
Connected Mode
After bonding is complete, the blue LED will ash at a slower rate of 2 secs
off, 1 sec on. The connection to that device is secure.
When Should I Release the Switch?
Idle Mode Pairing Mode Role Change Clear
seconds
Pairing to a Device with Bluetooth Wireless Technology
1. Set your Bluetooth device to Pairing Mode following the
manufacturer’s instructions.
2. On the RemoteMix 3.5, pull up on the switch < > and hold for
approximately 5 seconds. The blue LED will begin to ash rapidly as
RemoteMix 3.5 enters Pairing Mode. Pairing Mode will time out in 2 minutes.
3. On your Bluetooth device, from the list of Bluetooth connections, select
“JKRM3.5xxxx” where “xxxx” corresponds to the last 4 digits of the
unit’s serial number. Enter “Yes” when asked to bond with this device.
The pin is “0000”.
4. When bonding is completed, the blue LED will ash at a rate of 2 secs off,
1 sec on.
8
RemoteMix 3.5™ Broadcast Field Mixer
Bluetooth LED
Bluetooth Wireless Technology
Note: Establishing a Bluetooth connection varies with different cell phones.
Reconnecting to a Device wtih Bluetooth Wireless Technology
Once RemoteMix 3.5 has been added to your Bluetooth device, subsequent
connections can be made more quickly from Idle Mode. Simply hold the < >
switch up >2 seconds to reach Idle Mode for faster connection. Idle Mode will
time out in 2 minutes if the device is left unused or call is disconnected.
Disconnecting from a Device with Bluetooth Wireless
Technology
To disconnect from the Bluetooth device, simply pull up on the < > switch and
hold for 5 seconds.
Bluetooth Wireless Technology
RemoteMix 3.5 will rst attempt to connect in Hands-Free mode offering a
3.4 kHz mono duplex connection. If both phones on the call support HD voice,
Hands-Free mode supports a 7 kHz mono duplex connection. If a Hands-Free
connection is not available, RemoteMix 3.5 will attempt to connect in A2DP mode
with a 20 kHz, one-way, stereo connection. Consult your cell phone or portable
device for more details.
Bluetooth Wireless Technology
9
FAQs
1) Why do I keep getting an error message when I try to pair
with my Bluetooth enabled cell phone?
There is a difference between Idle Mode and Pairing Mode. The rst time
you make a connection with a new Bluetooth enabled device, you must be in
Pairing Mode. Please read carefully through the instructions on page 8 of this
User Guide for detailed information.
2) What is the range of the Bluetooth transmitter/receiver?
The RemoteMix 3.5 will transmit and receive audio signals up to 33 feet
from your Bluetooth device. The maximum range of this product is achieved
when a clear line of sight is maintained between connected devices, but may
also be limited by interference due to the environment. While this product
offers extended range capabilities, maximum usable range is limited by the
weaker of the two paired/connected devices. Transmitting signals over longer
distances will require more power, therefore you should keep RemoteMix 3.5
as close as possible to your Bluetooth device to conserve battery power.
3) How long will the batteries last in my RemoteMix 3.5?
There are many variables that affect battery life, such as the number of
headphones, and the use of Bluetooth. All of our battery life tests included
3 headphones playing music at average listening levels. These tests use
standard alkaline batteries. Lithium batteries can add 3 to 4 times the battery
life, at 3 to 4 times the cost.
The following numbers are from lab tests and may not represent your usage:
7 hours of broadcast through a cell phone using Bluetooth Wireless
Technology at a distance of 1 meter.
10 hours of broadcast through the phone line hybrid, using dynamic
microphones.
4) Why doesn’t my RemoteMix 3.5 ring when a call comes in?
The audible ringer found on some of our other RemoteMix units was replaced
with a visual ring indicator on the RemoteMix 3.5. This red LED ashes when
a call comes in. The Ring indicator is located directly below the keypad on the
front of the unit.
5) Will any cellular telephone work with RemoteMix 3.5?
The wireless interface on the RemoteMix 3.5 works very well with most
cellular telephones. However, some wireless telephones generate excessive
RF noise which can be heard as a “chattering” or “motor boat” sound.
The noise from these particular telephones will be unacceptable for most
broadcast applications. Also, some wireless phones have the standard 2.5
mm headset jack while others have a 3.5mm stereo headset jack and others
have proprietary jacks. Adapters to convert the proprietary jack to a standard
3-conductor 2.5 mm jack or 4-conductor 3.5mm jack are available for most
wireless telephones through their dealers, local electronic stores or many
internet stores
10
RemoteMix 3.5™ Broadcast Field Mixer
FAQs
6) What kind of device can I connect to the Cue Input?
Setting the switch for the dual-purpose 1/4” input to Cue Input will provide
a standard line level input for connection to another audio device, such as
a portable radio. The audio signal will be sent to all three of the headphone
outputs. This way, your announcers can listen for a cue from their radio
station at the end of a station break.
7) The cellular interface cable was left behind at our last event.
Can I get a replacement at our local audio supply store?
This is a custom made cable and is not wired the same as those that may
be available at your local electronics store. Please contact your JK Audio
dealer or our Customer Service department and ask for either a CN045 or a
CN113 replacement cable. The CN045 has a 2.5mm TRS headset plug and
the CN113 has a 3.5mm TRRS headset plug. Most newer phones, especially
those that include a mp3 player, have a 3.5mm TRRS headset jack and
therefore require the CN113 cable.
8) The output from Mic 3 is very low but the other mics are ne.
Check the position of the <Mic/Line> switch near <Mic 3>. This input can be
switched to accept a line level signal from a mixer or other equipment.
9) How can I tell how much battery life is remaining?
The red <Power> LED functions as a battery life gauge that will gradually dim
as the battery runs down. This red LED will go completely dark about a half
hour before the unit shuts down. Keep in mind that the VU meter, Bluetooth,
and clipping LEDs will remain bright until the unit stops functioning.
10) Does the AC power supply charge the batteries?
No. You may use rechargeable batteries, but you must remove and recharge
the batteries outside of the RemoteMix 3.5.
11) I’ve lost my power supply for my RemoteMix 3.5 unit. I
have a power supply that ts from a different product. Can I
use this instead?
No! Never use a power supply other than the one that was supplied by your
manufacturer. Power supplies are available in either AC or DC output with
many combinations of voltage and available current. Most consumer power
supplies are not regulated. This could invariably damage your equipment,
and also create a great deal of noise. Our products are designed for and
tested with their respective power supplies for optimum operation. If you
have lost your power supply, please contact your JK Audio dealer or our
Customer Service department and ask for a PS009 power supply for your
RemoteMix 3.5.
FAQs
11
Technical Information
Block Diagram
Output
Master
3.5 mm
Master
Stereo
Output
LED
Headphone
Meter
Limiter
1
Bluetooth
2
Headphone
Jack
Handset
3
Headphone
Handset
Interface
Universal
Cue Input
Wireless Phone
Headphone Cue
Return
Line
Phone
Hybrid
Headset
Emulator
DTMF
Phone Line
Keypad
1
XLR
Input
12
RemoteMix 3.5™ Broadcast Field Mixer
XLR
Input
Mic / Line
2
XLR
Input
3
3.5 mm Line Input
Technical Information
Specications
Input Impedance / Level
Female XLR (3) Mics:
1/8” (3.5mm) Stereo Line: 20k ohms / -10 dBm nom
Headphone Cue 1/4”: 20k ohms / -10 dBu nom
Output
Balanced Male XLR: +16 dBu max, 20 Hz - 20 kHz, +/- 1dB
1/8” (3.5mm) Stereo: 100 ohms, -10 dBu nom
Headphone 1/4” Stereo: 8 ohms / 1/3 watt per channel
Bluetooth
Frequency Response:
Distance: 33 ft (10 meters)
Misc.
Phone Line Connector RJ11C
PBX Interface RJ22
Ringer 0.5B REN
Isolation 1500 VAC
Power 100-240 VAC, 50-60Hz or Two 9 VDC batteries
Size 9.5” x 8” x 3”
Weight 3.8 lbs
2k ohms / -25 dBu nom
( Channel 3: Mic/Line pad switch = +6 dBu max )
Hands-Free (phone): 300 Hz - 3.4 kHz
Hands-Free (HD Voice): 50 Hz -7 kHz
A2DP Mode: 30Hz - 17 kHz
Declaration of Conformity
Manufacturer’s Name:
Manufacturer’s Address:
Declares that the product:
Product Name:
Model Numbers:
Conforms to the following Product Specications:
Safety:
ESD:
JK Audio, Inc.
th
1311 E 6
Sandwich, Illinois 60548 USA
RemoteMix 3.5 Broadcast Field Mixer
RemoteMix 3.5
AS/NZS 60950.1:2003
CAN/CSA-C22.2 No. 60950-01-03
UL Standard 60950-01 1st edition
EN 55024:1998; EN 61000-3-2; EN 61000-3-3
Street
Technical Information
13
FCC Registration
Declaration of Conformity Cont’d
Emissions:
Telecom:
The product herewith complies with the requirements of the following Directives and
carries the CE marking accordingly:
The Technical File containing supporting documentation is maintained at:
EN 55022:1998
AS/NZS CISPR 22 (2002)
FCC Part 15, Subpart B
ICES-003
EN 300 328
FCC Part 15.247 FCC ID R47F2M03MLA
IC Radio Standards RSS-210 Annex 8
AS/ACIF S002:2005
FCC CFR 47, Part 68
TIA968 A-1, A-2, A-3, A-4
LVD 2006/95/EC (Safety)
R&TTE 1999/5/EC (Telecom)
EMC 89/336/EEC (EMC)
RoHS Directive 2002/95/EC
JK Audio, Inc (Corporate Headquarters)
Compliance Manager
1311 E 6th Street
Sandwich, Illinois 60548 USA
815-786-2929 phone
815-786-8502 fax
FCC Registration
Your new JK Audio product has been registered with the Federal Communications
Commission (FCC). This product complies with the standards in Part 68 of the
FCC rules.
1. Connection and use with the nationwide telephone network
The FCC requires that you connect this telephone equipment to the national telephone
network through a USOC RJ-11C modular telephone jack. This equipment may not be
used with Party Line Service or Coin Telephone Lines. This equipment is hearing aid
compatible.
2. Information for the telephone company
Upon request from your local telephone company, you are required to provide the
following information:
A. The “line” to which you will connect the telephone equipment (that is, your
telephone number), and
B. The telephone equipment’s FCC registration number.This can be found on the
bottom of your telephone equipment, and,
C. The ringer equivalence number (REN) for this equipment. The REN is used
to determine the quantity of devices which will be connected to the telephone
line. Excessive RENs on the telephone line may result in the devices not
ringing in response to an incoming call. In most, but not all areas, the sum of
the RENs should not exceed 5.0. To be certain of the number of devices that
may beconnected to the line, as determined by the total RENs, contact the
local telephone company.
14
RemoteMix 3.5™ Broadcast Field Mixer
FCC Part 15 Compliance
3. Repair Instructions
If it is determined that your telephone equipment is malfunctioning, the FCC requires
that it not be used and that it be unplugged from the modular outlet until the problem
has been corrected. Repairs to this telephone equipment can only be made by the
manufacturer or its authorized agents or by others who may be authorized by the
FCC. For repair procedures, follow the instructions outlined under the warranty section
of the manual.
4. Rights of the telephone company
If telephone equipment is causing harm to the network, the telephone company may
temporarily discontinue your telephone service. If possible, they’ll notify you before
they interrupt service. If advanced notice isn’t practical, you’ll be notied as soon as
possible. You’ll be given the opportunity to correct the problem, and you’ll be informed
of your right to le a complaint with the FCC. Your telephone company may make
changes in its facilities, equipment, operations or procedures that could affect the
proper functioning of your JK Audio product. If such changes are planned, you’ll be
notied by your telephone company.
FCC Part 15 Subpart A Compliance
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interfer-ence when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his/her own
expense.
Changes or modications not expressly approved by JK Audio can void the user’s
authority to operate the equipment.
FCC Part 15 Subpart B Compliance
This device has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communication. Operation of this
equipment in a residential area is likely to cause harmful interference, in which case
the user will be required to correct the interference at his/her own expense.
Changes or modications not expressly approved by JK Audio can void the user’s
authority to operate the equipment.
Shielded interface cables and AC power cord, if any, must be used in order to comply
with the emission limits.
The internal antennas used for this mobile transmitter must not be colocated or
operated in conjunction with any other antenna or transmitter.
FCC Complaince Notice
15
RemoteMix 3.5™
Broadcast Field Mixer
User Guide Version 8/7/14
JK Audio, Inc.
1311 E 6th St.
Sandwich, IL 60548
United States
Telephone: 815.786.2929
Toll Free: 1.800.jkaudio
Fax: 815.786.8502
www.jkaudio.com
© 2014 JK Audio, Inc. All rights reserved.
JK Audio
Loading...