JJPlus JWX5253 User Manual

JWX6052/JWX6053 Mini PCI-e User’s Manual

1. Product Overview

The JWX6052 Mini PCI-e adapter cards contain an Atheros QCA9880 chip,
and the JWX6053 Mini PCI-e adapter cards contain an Atheros QCA9890
chip for IEEE 802.11a/b/g/n/ac Wireless LAN applications. The mini PCI-e
adapter cards support key security features like Wi-Fi Protected Access
(WPA), WPA2, WEP and 802.1x.
Typical application of the card is integration into other wireless products
such as AP/ Router which is used distance 20cm away human body.

2. Packaging Contents

The mini PCI-e card package contains the following item(s):
1 x Wireless Mini PCI-e Adapter

3. Installation guide

 Shut down the power of the platform
 Align the Mini PCI-e adapter with the Mini PCI-e socket on the platform
 Adjust and push down the Mini PCI-e adapter gently until the metal locking

levers on the Mini PCI-e socket is latched. (Please take note that the Mini
PCI-e adapter can only fit in one direction due to the keyed notch. Wrong
orientation will cause improper installation and may damage the Mini
PCI-e socket)

 Connect the antenna(s) on the mini PCI-e module
 Reboot on the platform
 Install drivers if necessary

4. Frequency

802.11b/g/n: 2412 ~ 2462 MHz

802.11a/an/ac: 5180 ~ 5825MHz
Connector: Reverse U.FL PLUG

5. Federal Communication Commission Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular

jjPlus CORP.

13F-3, No.120, Qiaohe Rd., Zhonghe Dist., New Taipei City 235, Taiwan

installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the
following measures:

 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

6. FCC Caution
 Any changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate this
equipment.

 This transmitter must not be co-located or operating in conjunction with

any other antenna or transmitter.

7. FCC Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body.

8. This device is intended only for OEM integrators under the following

conditions:

1) The antenna must be installed such that 20 cm is maintained
between the antenna and users, and the maximum antenna gain
allowed for use with this device is 5 dBi.

2) The transmitter module may not be co-located with any other
transmitter or antenna.

As long as 2 conditions above are met, further transmitter test will not be
required. However, the OEM integrator is still responsible for testing their
end-product for any additional compliance requirements required with this
module installed

9. Important Notes

In the event that these conditions can not be met (for example certain
laptop configurations or co-location with another transmitter), then the FCC
authorization is no longer considered valid and the FCC ID can not be used
on the final product. In these circumstances, the OEM integrator will be
responsible for re-evaluating the end product (including the transmitter) and
obtaining a separate FCC authorization.

jjPlus CORP.

13F-3, No.120, Qiaohe Rd., Zhonghe Dist., New Taipei City 235, Taiwan