J&J Electronics Color Splash, Color Splash LPL-F1C, Color Splash LPL-S1C Installation And Operation Manual
Technical Support
Phone: 800.735.4553 ext. 242
For more information about this or other J&J Electronics lighting products,
please visit www.jandjpoolspa.com
Color Splash® LED Pool and Spa
Light Fixture Installation and
Operation Guide
Color Splash® LED POOL AND SPA LIGHT FIXTURES
Available in 120VAC and 12VAC models
Color Splash LED Pool and Spa light xtures offer superior, color illumination for
your pool and spa. This owner’s manual contains important information on installing
and using your new Color Splash LED Pool and Spa light xture. Read and follow all
instructions contained in this manual. Please keep it in a safe place for future reference.
Most states and local codes regulate the construction, installation, and operation of
public pools and spas, and the construction of residential pools and spas. It is important
to comply with these codes, many of which directly regulate the installation and use
of this product. Consult your local building and health codes for more information.
Read and follow all warning notices and instructions contained in this guide before
installing or using the product. Severe injury, death or property damage may result if
the warnings and instructions contained in this manual are not followed.
INSTALLER NOTICE: This Installation and Operation Guide contains important
information about this LED light. Be sure to give this guide to the owner and/or
operator of the LED light for reference regarding the proper installation, operation
and use of this product.
DANGER! FAILURE TO PROPERLY INSTALL AND USE THIS PRODUCT CAN
RESULT IN SERIOUS BODILY INJURY OR DEATH.
WARNING! Comply with all related codes for the installation and
use of this product.
WARNING! Before installing or using this light, read all warnings and
instructions contained in this manual.
pg 1
COLOR SPLASH LED POOL AND SPA LIGHT FIXTURE NICHE COMPATIBILITY
For LPL-F1C ONLY
Pentair®: 78210400, 78210500,
78210600, 78210700, 79206700
Hayward®: SP0604C, SP0600U
Jandy®: PLNICLRG, SSNICLRG1R,
SSNICLRG1S
Jacuzzi®: 94131234
For LPL-S1C ONLY
Pentair®: 78244200, 78244300, 78243200,
78243300, 79206600
Hayward®: SP0606C, SP0610C
Jandy®: PLNICSM, SSNICSM1R, SSNICSM1S
Always disconnect power to the pool and/or spa light at the circuit breaker panel
before attempting to service the light. Failure to do so could result in serious injury
or death due to electrical shock. Installation must be performed in accordance with
all applicable federal, state & local installation codes and ordinances by a licensed or
certied electrician or a qualied pool professional. Improper installation may result
in death or serious injury to pool and/or spa users, installers or others due to electrical
shock. In addition, improper installation may cause property damage. This device is
not intended for use in anything other than in-ground pools/spas.
WARNING! Risk of electrical shock or electrocution
Do not, under any circumstances, splice wire underwater or behind the light niche
during the installation of this light.
Color Splash LED Pool and Spa light xtures are operated through the light’s switch.
No special controller or interface is required. Use a junction box to connect and
operate multiple lights with a single switch.
The following steps detail installation of the Color Splash LED light xture into a new
pool and/or spa construction. Read this section in its entirety prior to beginning any
installation.
WARNING! Important Safety Information for Light Installation
INSTALLER NOTICE: This light’s external cord cannot be replaced and should be
handled with care. Any damage to this external cord necessitates replacing the light.
pg 2
OPERATION FOR 120VAC AND 12VAC
COLOR SPLASH LED POOL AND SPA LIGHT FIXTURES
COLOR SPLASH LED POOL AND SPA LIGHT FIXTURES INSTALLATION
(NEW POOL AND/OR SPA CONSTRUCTION)
INSTALLER NOTICE: A licensed electrician must complete the following steps prior to
installation of this light in a new pool or spa construction.
RATED FIXTURE LIFE: The illumination generated by Color Splash LED light xtures
are based on Light Emitting Diode (LED) technology. The average expected xture
life is rated 50,000 elapsed time hours under normal operating conditions. Pool Water
Temp: 33°F to 97°F (1°C to 36°C), humidity: 0-95% non-condensing.
4" Min.
48" Min.
18" Min. Top of Lens
to Water Level
8" Min. Junction Box
or Low Voltage
Transformer to the
Max. Water Level of Pool
To: GFCI, Circuit Breaker,
and Power Source
Rigid Conduit
#8 AWG Ground
Connector Bonding
Lug is Located at
Rear of Niche
Coil 4 ft. of Power
Cord Around Fixture
Concrete Must Be Cut
Back Around Niche to
Allow for a Compacted
Plaster Seal
1. Feed the xture cord through the conduit to the junction box. Be sure to leave at
least four (4) feet of cord at base of the xture to coil around the light to ensure ease
of servicing once the pool and/or spa is lled; reference Figure 1.
Figure 1.
NEW CONSTRUCTION INSTALLATION STEPS
(ONCE ALL ELECTRICAL REQUIREMENTS ARE MET)
pg 3
ordinances. The electrical system must be installed by a licensed or certied electrician to
meet or exceed those requirements prior to installation of the light. This includes, but is not
limited to, the following National Electrical Code requirements:
• Installation of a ground fault circuit interrupter (GFCI) for line voltage models on the
lighting circuit with an appropriately rated circuit breaker.
• A junction box or low voltage transformer is located at least 8 inches above the maximum
pool water level and at least 48 inches from the pool edge; reference Figure 1.
• Proper electrical bonding of the light xture and all metal items within 5 feet of the pool
• Proper wet niche installation with the top edge of the underwater light’s lens at least
18 inches below the surface of the water in the pool and not more than 20” in Canada;
reference Figure 1.
• Proper electrical wet niche bonding and grounding using the #8 AWG ground connector
at the rear of the niche; reference Figure 1.
WARNING!
Conrm that the pool and/or spa meets all current National Electrical
Code (N.E.C.) Article 680-22 requirements and any applicable local codes or
Loading...