JJC RM-E4
Infrared Remote Control Instruction
Thank you for purchasing JJC RME4 Infrared Remote Control. For the best performance, please read this
instruction carefully before use.
z To use RM-E4 Remote Control
1. For the first time use, please pull out the plastic separator (if your remote control has it) at the battery
holder.
2. Mount the camera on a tripod (recommended) or place the camera on a stable, level surface.
3. Press the button and rotate main command dial until (delayed remote) or (quick response remote) is
displayed in the control panel.
4. Aim the transmitter on the remote control at the infrared receiver on the camera (usually within +/- 20
degree of the lens axis, from the left to the right and from the top to the bottom) and press the shutter-release
button on the remote control (when using the remote outdoors, make sure that the subject is not backlit and
that the line of site between the transmitter and the infrared receiver is not blocked by the lens or other
obstacles).
5. How the camera focuses and shoots depends on the option selected for your camera's custom setting. For
further information, check your camera's manual.
Infrared cannot be seen by human eyes. So you will see no visible light from the LED on the front end of the
remote control when operating.
1
z Identifying the buttons
controls zoom, image display, and toggle displays
z Specification
z 100% compatible with Pentax Remote E infrared remote controls.
z Works with all remote shutter release control modes (Quickresponse, W/T Zoom).
z Easytoreplace CR2025 lithium battery.
z Operating temperature: 5 °C to 40 °C (40 °F to 105 °F).
z Typical Battery Life: up to 3 years, 20,000 exposures.
z To Replace the Battery
1. The remote control is powered by a three-volt CR2032 lithium battery which is already included in.
2. After sliding the latch in the direction shown to unlatch the battery holder, remove the holder.
3. Remove the battery from the battery holder.
4. Insert a fresh battery with the face marked "+" on top.
5. Slide the battery holder into the remote until the latch clicks into place
2
z Attention
ٛ a. When the remote control is not in use over a long time, please remove the battery from the
remote control.
ٛ b. Do not leave the remote control in places subject to extremely high temperatures.
Pentax Part compatible with Pentax Cameras (P part)
Digital SLR *ist DL *ist DS *ist D
S S4 S4i S5i S5n SV
Optio
Film SLR
330 430 450 550 555 750z
S50 S40 S60
*ist MZ6 MZ-L ZX-L K100D K110D
K10D K20D K200D KM K2000 K-x
K7
Pentax Part compatible with Samsung Cameras (P part)
Digital SLR GX-1L GX-1S GX-10
Canon DSLR/SLR part compatible with Canon Cameras (C1 part)
300D 350D 400D 450D 500D
Digital SLR
Film SLR
APS SLR EOS IX
SureShot
(Prima Super)
ELPH 370Z Z3
REBEL XSI KISS X2 Digital Rebel Digital Rebel XT Rebel T1i
5D Mark II EOS 7D 550D Rebel T2i
ELAN 7 10 30 33 50
55 100 300v 300x 3000v QD
Rebel K2 Rebel T1 Date Rebel T2 Date Kiss III Kiss III L
Z180u Z155 120
Canon DC part compatible with Canon Cameras (C2 part)
Power Shot Pro 1 G6 G5 G3
G2 G1 S1 IS S70*
S60* Pro 90 IS
*Only work with shutter function.
Nikon part compatible with Nikon Cameras (N part)
Digital SLR
Film SLR F65 F75 N65 N75
Coolpix 9000 8800 8400 P6000
LiteTouch 150ED 140ED 130ED 110S 100W
Nuvis Nuvis S
D3000 D5000 D90 D80 D70s
D70 D60 D50 D40 D40x
Copyright of JJC Technology Company
3
Loading...