SUBWOOFER
OWNER′ S MANUAL
JINLANG AUDIO CO. ,LTD.
HONOURABLE PURCHASER：：：：
Congratulations on purchasing your AURUM CANTUS active subwoofer.
You will enjoy years of trouble free Hi-End sound reproduction from it.
In order to achieve optimal performance, please read this manual carefully before use.
Please keep this manual in a safe and appropriate place for future reference.
SW-10 SUBWOOFER
This is an active subwoofer with exceptional performance that will compliment any Aurum Cantus
model and any other speaker brand.
FEATURES
SW-10 SUBWOOFER INCORPORATES THE FOLLOWING MAIN COMPONENTS:
CABINET
By utilizing thick high quality MDF, the front baffle is designed to be low diffraction.
CONE DRIVER
254 mm/10″ NOMEX composite cone, solid aluminum metal frame, 65mm/2.56″ high power voice
coil, and a strong magnet system.
AMPLIFIER
A patented power amplifier is assembled in the rear panel of SW-10. The crossover of the amplifier
allows you to set the crossover point of the subwoofer anywhere between 40-160Hz, also allow you to
change the phase response of the subwoofer, as well as increase or decrease the low gain.
SPECIFICATIONS
Design：
Active subwoofer system with rear port design.
Frequency response：
28Hz－114Hz±3dB
Frequency range of the crossover：
40Hz－160Hz（adjustable）
Average output sound level：
96dB（25Hz－62Hz）
Drive units：
254 mm /10″, NOMEX composite cone，long throw.
Dimension:
Height: 458mm /18.03″，(exclusive of removable spikes)
Width: 335mm /13.19″
Depth: 500mm /19.69″ , (inclusive of the radiator of the amplifier)
Finish:
Cabinet: Matt Finish in Cherrywood, rosewood or reflective maple，also
high gloss finish(high gloss Piano paint finish) is available.
Net weight:
30kg /66lb
Amplifier:
Class:
B
Maximum undistorted power output:
200W（80Hz THD0.45% 4ohms）
Input impedance:
≥47kohms
1
Signal/Noise：：：：
90dB
Function:
Level/volume control–crossover frequency control–automatic control–phase control-low
gain control.
Input terminals：
Line level，high level/speaker level.
Output terminals:
Line level，high level/speaker level.
Low pass filter：
Active second order, variable crossover point.
High pass filter：
Passive first order, variable crossover point.
AMPLIFIER DIAGRAM
AMPLIFIER’S UTILIZATION AND SETUP
1. Volume level control:
Before power up, you must assure that the volume level control is set in the lowest position, after
starting; you can adjust the volume level control until you are satisfied with the volume.
2. Crossover frequency control：
The variable crossover frequency allows you to set the crossover point of the subwoofer anywhere
between 40-160Hz. Increasing the crossover frequency will allow more mid-low output from the
subwoofer and decreasing the crossover frequency will allow less mid-low output from subwoofer.
2
3. Automatic control：
When setting to AUTO，the amplifier will be in automatic control status, here the amplifier will
automatically turn on once the audio signal is detected at the line level input or high level/speaker
level input. When set to ON the automatic control will be shut down. When set to OFF the
amplifier will be shut down.
4. Phase control：
This control can change the phase of the subwoofer. Generally, the phase should be set in the left
of 0°position; it may cause more or less mid-low frequency if the phase is set in the 180°position.
5. Low gain control：
Different low gain control allows you to set anywhere between 0-6dB. Increasing gain will allow
more output of mid-low frequency, and decreasing gain will allow less output of mid-low
frequency.
6. Line level input：
These RCA terminals are for the line level input signal coming from an AV Receiver, AV
Amplifier or preamplifier. Note! Do not connect the high level/speaker level signal to these RCA
terminals.
7. Line level output：
These RCA terminals can be connected to another power amplifier. A full range signal is sent
through these terminals.
8. High level/speaker level input：
These terminals are for the signal input from power amplifier or speaker level. Note! Do not use
the line level input and high level/speaker level input both simultaneously.
9. High level/speaker level output：：：：
These terminals are to be used for connecting satellite speakers/main speakers. These terminals
can be used only when using high level/speaker level input.
10. High pass crossover control：
This is a switch for high pass crossover. This crossover limits the low frequencies, which has 80Hz
and 120Hz two options. The crossover can be used only when using high level/speaker level input
and high level/speaker level output. Note！Do not operate the switch of high pass crossover when
amplifier is working.
11. Power switch.
12. Power input terminals.
13. Working indication.
THE PLACEMENT AND INSTALLATION OF SUBWOOFER
The size of the room, the treatment of the wall and floor surfaces, the position of furniture and the
placement location of the subwoofer in the room are all factors to achieve optimal sound reproduction.
Please carefully read the following references：
● If placing the subwoofer in a corner it will make the subwoofer sound louder and boost the very
lowest frequency. If placing the subwoofer away from walls it will make the subwoofer sound
lower. So we recommend that you look for the optimal position according to the size and overall
arrangement of the room. The optimal position can be set up as long as you experiment by moving
the subwoofer a number of times.
● If the floor is too smooth it will make the sound quality of the subwoofer muddy. The sound
quality will improve if you place a small rug on the floor.
● The subwoofer should be located on a flat stable floor; spikes should be installed and adjusted to
suit.
3
CONNECTING YOUR SUBWOOFER
It is very simple to connect the subwoofer; you can choose line level input or high level/speaker level
input. Please note! Do not connect the high level/speaker level signal to the line level input. Please
assure that the volume level control is set in the lowest position before power up. Furthermore, we
recommend you to set the phase control to the position of 0º, and set the low gain to the 0dB position,
you can adjust the volume level control slowly until you are satisfied with the volume.
SUBWOOFER BREAK IN PERIOD
After testing, the subwoofer requires at least 20 hours of break in to obtain the normal working
condition. In order to achieve the optimum performance sooner, we recommend the subwoofer break
in as continuously as possible.
CLEANING YOUR SUBWOOFER
Use a damp cloth to clean the cabinet. We recommend maintaining an occasional furniture grade wax
and polish the wood surface of the cabinet.
ATTENTION
Subwoofer should be placed away from heat sources and prevent direct sunlight on the subwoofer.
Otherwise, this can cause life reduction of the drivers and aging of the cabinet finish.
Make sure that you have read and understood the information in this manual. If there is anything
you don’t understand or are unsure of, please contact your AURUM CANTUS dealer or
distributor.
Now it’s your responsibility to set up your subwoofer following the recommendations set out in
this manual.
WARRANTY AND SERVICE
This Subwoofer is warranted to be free of manufacturing defects for three [3] years after the original
date of purchase.
If the subwoofer should require service during the warranty period, we will repair or replace at our
discretion. The warranty does not apply to damage caused by abuse or wrong use to the subwoofer,
and does not apply to accidental damage and neglect or damaged during the course of transportation,
unauthorized modifications or repairs by people who are not permitted by an AURUM CANTUS
dealer or distributor.
Please contact your AURUM CANTUS dealer or distributor if you have a service requirement.
Please use the original packaging when you ship the subwoofer to an AURUM CANTUS dealer or
distributor for servicing. If you did not save the original packaging, please inform your dealer or
distributor, and they will send you replacement packaging. The packaging will be charged to you at
cost price.
All freight and insurance will be paid by the user.
4
PENGLAI JINLANG AUDIO CO.,LTD.
NO.1 XIANQIAO STREET,BEIGUAN ROAD,
PENGLAI P.R. OF CHINA
P.C.: 265600
TEL: 86-535 5643369
FAX: 86-535 5610809
E-mail: aurumcantus@aurumcantus.com
Http://www.aurumcantus.com
Loading...