JH08 Wireless Home Monitor
User Manual
Version: J1409-1.0
www.jimilab.com
Please read this manual carefully before usage for fast and correct operation.
Product appearance, color and accessories are subject to change without notice.
1 Accessories
Check the product and accessories as below to see if they are complete,
otherwise please contact your local supplier.
Camera body
Charger
Wall mount (Optional)
Power cable
Magnetic base
Setscrew×3 (Optional)
Screw×3 (Optional)
2 Specications
Type JH08
CPU 32bit RISC SoC Processor
Image sensor 1/4"Color CMOS Sensor
Image resolution HD 720P(1280*720), WVGA(854*480)
Camera lens Aperture F2.8, 127° wide angle
Video compression format H.264
Video bitrate Dynamic VBR 32Kbps-2Mbps self-adaption
FPS Max 30fps
Audio working mode Two-way voice intercom, one-way monitor
Audio format ADPCM (16bit/8KHz)
Network interface WiFi (IEEE802.11b/g/n)
Connection way Wireless connect to AP, AP to P2P directly
Infrared night vision Auto Infrared LED(within 10m)
Memory
TF Card (Max 32G) local storage and cloud
storage server
Video format AVI
Working status indicator Bi-color LED Indicator Light
Photo capture Support
Motion detection alarm Support alarm message pushing
Mobile terminal Support iOS/Android System Smart phone
Max terminal number 10
Working environment -30°C~60°C,Humidity<95%
Upgrade way Support Firmware OTA Remote Upgrade
Security setting 128bit AES Password
Power consumption <5W
Power input 5V/1A, USB Interface
Dimensions
50(L)×50(W)×98(H)mm (with base)
40(L)×36(W)×89(H)mm (without base)
3 Structure
Speaker
Camera
LED indicator
Mic
Magnetic base
Power input
Micro SD slot
3.1 LED indicator status
Status Meaning
Blue constant on AP setting mode
Blue ashing slow WIFI connection normal
Red ashing slow one time in interval Recording
Red ashing fast two time in interval User viewing online
Red ashing fast constant Upgrading
4 Operation
4.1 Connect with power
1. Connect with the power cable and charger
2. The Blue LED indicator will be ashing slowly if the device is connected
successfully with the WIFI network. If the Blue LED is constant on, it means
the WIFI network is not set correctly or there is no WIFI, and it will enter into AP
setting mode.
4.2 Fast setting
4. 2.1 A PP
Please download APP “Jimilive” from APP store or at www.jimilab.com.
4.2.2 WIFI setting
1. When the device is powered and the blue
LED is constant on, nd the AP hotspot
“JH008_”+”rst 6 digit of the device UUID”
in WLAN settings. Click to connect and the
default password is “88888888”.
2. After the connection is made successful,
start the APP on your phone, then click
“add camera”.
3. Click “Search” button.
4. Click the device “UUID” from search result,
or type in the “UUID” manually.
5. Type in the default password “88888888”,
name the device, then click “OK”.
6. Click the device and enter the monitoring
screen in AP mode.
7. Click the on the right to show the setting
menu
.
8. Click “Edit camera”, “Advanced” to show the setting.
1/2 2/2
1/5 2/5
3/5 4/5
5/5
9. Click “Modify security code” to change the
default password, default password is
“ 88888888”.
10. Click “Alarm Time Set” to set motion detect activate time, during which alarm
message will be available.
11. Firmware Update: During update, please
don’t cut off power, otherwise please contact
your supplier.
Time Synchronization: Synchronize the
time between cellphone time and device
time. (after time-zone is set in camera, the
camera time will change accordingly).
Restart camera: To restart camera and
x malfunction if any.
12. DropBox upload verication: to activate the DropBox upload function for event
recordings, you need to link your dropbox account with JimiLive.
13. Click “manage WIFI networks” to connect to a WIFI SSID, type in the password
and click “OK”, the device will reboot and connect to this WIFI network. The
connection is successful if the LED blue light is ashing slowly and the device
is online in APP.
Beeper alarm description:
Beeper status Meaning
Beep two times Wi setting success
Beep four times Password wrong
Beep ve times Connection failure
14. After the Wi-Fi is connected successful, the device is ready for remote live-monitor,
two-way talk, snapshot, video recording and alarm messages review, etc.
5 Installation
you can put the device on a at surface with the magnetic base or install it on the
wall or the ceiling. Details please check below:
Notice: a. Before installation, please make sure the device is close to the
power socket.
b. Before secure the pin and the screw, please drill holes on at and
solid surface.
5.1 Wall mount installation
5.1.1 Remove the pin from wall mount
5.1.2 Drill holes
Drills holes on the wall according to the position of the pin holes.
5.1.3 Secure the pin to the wall
Place two setscrews into the holes, then secure
the pin to the wall with the two screws.
5.1.4 Secure the device on the wall mount.
5.1.5 Secure the wall mount to the pin
.
5.2 Ceiling installation
Notice: Please set “Video ip” in the APP’s “Camera setting” if install on the
ceiling, otherwise the image will be back side down.
5.2.1 Use a slot type screwdriver to take out the top cover gently and reveal the
screw hole.
5.2.2 Drill holes on the ceiling according to position of the magnetic base.
5.2.3 Secure the magnetic base onto the ceiling
Use one setscrew and one screw to secure the magnetic base to the ceiling.
5.2.4 Press back the circle top cover
.
5.2.5 Place the device onto the magnetic base, and then adjust the angle to a
proper position.
6 Trouble shooting
During operating if encounter any problems, please read the following table,
contact your local supplier if the problem remain unsolved.
Common errors Possible Causes Solutions
Connection failed
Device not in WIFI
Conrm the device is connected
to WIFI successfully
WIFI network error Check WIFI status
Phone network error
Make sure your phone can
access internet
Cannot receive
motion detect alarm
messages
Motion detect not activated Activate motion detect function
Not login to APP
Make sure the APP is running or
running in backstage
Micro SD error
No SD card Insert SD card
Micro SD card fail Replace or format the card
Live view black
screen or replay
failure
Bad network connection of
cellphone
Improve network condition
Loading...