Jiffy LECTRIC STX PROII Operating Manual/parts Manual

POWER ICE DRILL

OPERATING MANUAL/PARTS GUIDE

Model #_________________

online at www.jiffyonice.com

Thank You for purchasing a Jiffy Ic e Drill. When properly maintained
and serviced, we are confident your drill will provide you with many
years of trustworthy performance. This manual contains operating and
safety instructions for the Jiffy Series Power Ice Drill. To receive the
greatest possible performance and satisfact ion from your Jiffy Power
Ice Drill, and to reduce the risk of injury, it is important that you read
and understand the assembly, operating, maintenance, and safety
instructions before using your Jif fy Power Ice Drill. Contact Feldmann
Engineering if you do not understand any of the instructions in this
manual.

As with any power tool, safety precautions must be observed with the
Jiffy Power Ice Drill to reduce the risk of personal injury. Careless or
improper use may cause serious injury and/or damage to your Jiffy
Power Ice Drill.

INDEX Page

General Information…………. 1
Warranty………………………. 1
General Safety Precautions… 2
Pre-Use Procedure………….. 2
Assembly of Drill…………….. 3
Battery Information………….. 3
Diagram of Main Parts, Parts List 4

MANUFACTURER’S
One Year Limited Warranty

(30 days for Commercial and/or Rental Use)

FOR WARRANTY SERVICE – DO NOT RETURN
YOUR DRILL TO THE RET AILER YOU PURCHASED
IT FROM. CALL THE JIFFY® CUSTOMER SERVICE
NUMBER AT 800-344-0712, MONDAY – FRIDAY
FROM 7:00 A.M. TO 4:30 P.M . CST, FOR A RETURN
AUTHORIZATION NUMBER AND INSTRUCTIONS.

Feldmann Engineering & Manufacturing Co., Inc. warrants the Jiffy
Power Ice Drill to be made of first quality materials and workmanship
and will, at its option, repair or replace any drill part thereof found to be
defective in such materials and workmanship if returned to the factory,
prepaid within one year from the date of purchase by the original
purchaser. To obtain warran ty service or replacement instructions,

you must have prior approval before shipping package. Call our
customer service department at 800-344-0712 Monday – Friday
from 7:00 a.m. to 4:30 p.m. for a return authorization number.

Inbound and outbound transportation charges are paid by the
purchaser. Feldmann Engineering assumes no responsibility for
damage caused by misuse, careless handling, or where repairs were
made or attempted by an unauthorized person. For repl acement parts,
call 800-344-0712, Monday – Frid ay from 7:00 a.m . to 4:30 p.m. CS T,
or go online to

www.jiffyonice.com

Manufactured by:

FELDMANN ENGINEERING & MANUFACTURI NG CO., INC.
520 Forest Avenue
Sheboygan Falls WI 53085

Phone: [phone] Monday – Friday 7:00 a.m. to 4:30 p.m. CST
FAX: [phone]

E-mail:

[e-mail]

Website:

Other products: TurfVent™ Lawn Aeration Eqt, BADGER™ Earth
Augers

www.jiffyonice.com

Purchased at______________
Date Purchased____________
Serial #__________________
Drill Size________________

Please complete Owner
Registration Card or register

Form WM3920 (07/10)

-1-

IMPORTANT SAFETY PRECAUTIONS

FOLLOW THIS SIGNAL ARE NOT OBEYED

IMPORTANT

Please read this manual carefully. Operat e your equipment according
to the safety instructions and recommendations found throughout this
manual. Anyone who uses this equipment must read and fully
understand the instructions and be familiar with its operation.

To receive the greatest possible performance and satisfaction from
your Jiffy Power Ice Drill, and to reduce the risk of injury, it is im portant
that you read and understand the assembly, operating, maintenance,
and safety instructions before using your J iffy Power Ic e Drill. Cont act
Feldmann Engineering if you do not underst and any of the inst ructions
in this manual.

Your Jiffy Power Ice Drill is designed and manuf act ured to provide safe
and dependable operation, provided it is operated in accordance with
the following safety precautions.

Preventing accidents is the responsibility of every power equipment
operator. The safety precautions identified in this manual must be f ully
understood and followed by every operator of this Jiffy Power Ice Drill.
Review the safety precautions frequently and never take chances.

Take the time to become familiar with your Ji ffy Power Ice Drill and its
components, then operate it in a safe manner. Study the appropri ate
sections of this manual for t he description of the cont rols and function
of your Jiffy Power Ice Drill. Teach the safety precautions to all
persons who use your Jiffy Power Ice Drill.

The STX PROII Lectric™ is desi gned for use with a J if fy lef t hand

When using an external battery source to operate your J iffy STX

After the Jiffy Cable Assembly (#3917) is attached to the STX

Avoid mishandling and abuse of your Jiffy Power Ice Drill. Handle

CAUTION

CAUTION INDICATES YOU CAN OR YOUR EQUIPMENT
CAN BE HURT IF THE SAFETY INSTRUCTIONS THAT

INDICATES HELPFUL INFORMATION FOR PROPER
ASSEMBLY, OPERATION, OR MAINTENANCE OF YOUR
EDQUIPMENT.

(counter-clockwise) rotation ice drill ONLY.

PROII Lectric™, use ONLY the Jiffy Cable Assembly (#3917),
Wiring Harness (#3939), or Extension Cable (#3929) designed
exclusively for the Jiffy STX PROII Lectric™ power head.

PROII Lectric™ power head, attach t he red clamp to the posit ive
[+] battery post and the black clamp to the negative [-] battery
post. Failure to do so can result in electrical damage to the unit
and/or serious bodily injury.

it with care, as any rough treatment can c ause damage to your
Jiffy Power Ice Drill or it can cause a malfunction.

Avoid unintentional starting. Use extreme caution when
transporting the STX PROII Lect ric™ from hole to hole while on
the ice

If drill lodges in the ice while drilling holes, release pressure from
the throttle assembly and pull drill from the hole. Start over.
(Keeping the throttle assembly engaged when the auger is not
turning can drain your battery and seriously damage your ice
drill.)

Disconnect the connection pin from throttle assembly before

transporting or servicing your ice drill.

Connected Disconnected

DO NOT SMOKE AROUND BATTERY
Batteries can explode causing severe injury. Hydrogen and

Oxygen gases are produced during normal battery operation.
This mixture can explode if flames or sparks are brought near th e
battery.

+ Never modify your Jiffy Power Ice Drill in any way. Only Jiffy ice

drills and accessories supplied by Feldmann Engineering or
expressly approved by Feldmann Engineering for us e with your
Jiffy Power Ice Drill are authorize d for connection and use. The
use of non-Jiffy or unauthorized components may cause damage
or injury.

Check the tightness of screws, nuts, and bolts at regular intervals
and re-tighten if necessary.

Do not wear loose clothing while operating your J iffy Power Ice

Drill and keep all clothes and parts of the body (hands, feet, etc.)
clear of the rotating ice drill assembly to avoid bei ng drawn into
the boring drill.

By wearing cleated or spiked shoes, or i ce creepers when using

your Jiffy Power Ice Drill, you will find it easier to control the
rotational torque as you drill holes in the ice.

Do not allow children to operate your Jiff y Power Ice Drill at any

time. Do not allow adults to operate your Jiffy Power Ice Drill
without proper operational instructions, including all safety
precautions.

Do not lend or rent your Jiffy Power I ce Drill without providing the

owner’s manual. Be sure that anyone who uses your Jiffy Power
Ice Drill understands the information contained in this manual.

Give your complete and undivided attention to the proper

operation of your Jiffy Power Ice Drill. To operate i t properly, you
must be in good physical condition and mental health and not
under the influence of any substance (alcohol, drugs, etc.) which
might impair vision, dexterity, or judgment.

+ Using your Jiffy Power Ice Drill may be strenuous. If you have

any condition that may be aggravated by strenuous act i vity, c heck
with your doctor before operating your Jiffy Power Ice Drill.

+ Do not operate your Jiffy Power Ice Drill when you are tired.

Fatigue may result in loss of control.

-2-

Pre-Use Procedure

Before using your Jiffy Power Ice Drill t o drill holes in ice, follow this
procedure to prepare for proper and correct use.

• Carefully examine your Jiffy Power Ice Drill for hidden
shipping damage. If any external damage is observed to the
Jiffy Power Ice Drill, contact Feldmann Engineering.

• Find, read and understand your Jiffy operators manual.
Contact your Jiffy dealer or Feldm ann Engineering if you do
not understand any of the instructions in this manual.

• Assemble the components of your Jiffy Power Ice Drill as
indicated in the Assembly of Drill section of this manual.
Leave the Jiffy Blade Protector on the drill assembly and
make certain it is securely fastened.

• Using the supplied battery charger/maintainer, fully charge
the internal battery before the first use.

DO NOT RETURN your Jiffy STX PROII Lectric™ Drill TO THE
RETAILER THAT SOLD IT T O YOU. THEY ARE NOT AUTHORIZED
TO PROVIDE REPAIRS OR WARRANTY REPLACEMENT unless
they are an authorized Jiffy warranty station. If you have any
questions concerning the authorization of a service station, contact
Feldmann Engineering.

Jiffy E-Z Connect™ Collar

Connect drill assembly to powerhead by sliding E-Z Connect™ Collar

down and pulling clevis pin out. Then slide drill assembly onto output

shaft. Reinsert clevis pin through drill assembly and output shaft, then

slide E-Z Connect™ Collar up to lock pin in place.
Note: Do not remove clevis pin from collar tether.

Charging the Internal Battery (AGM ETX9, 12 Volt)

BATTERY DOC®

The Ideal Portable Wallmount Battery Charger

For Your Jiffy® Lectric Model 55 Ice Drill

The 1Amp version, of the Wall-mount Battery Charger em pl oys state of
the art electronics perfect for AGM (absorbed glass mat) 12-Volt
battery supplied with your Model 55 Ice Drill. The BATTERY DOC® is
a highly efficient, reliable battery charger that will safely charge and
maintain your battery at peak condition 24hours a day 365 days a year.

FEATURES

 Small Lightweight construction.
 UL 1236 approved for everyday use
 Short Circuit protected with Automatic Recovery.
 Three Color LED Charge Indicator
 Electronically monitored Over Current Limiting
 Two Stage Charging Constant Voltage (Maintenance)

Constant Current (Charging)

 Universal AC input 100 - 240VAC, 50/60Hz

This manual contains important safety and operating
instructions for your battery charger.

1. Use of an attachment not recommended or sold by the battery
charger manufacturer may resul t in a risk of fire, electric shock, or
injury to persons.

2. To reduce risk of damage to electric plug and cord, pull by plug
rather than cord when disconnecting charger.

3. An extension cord should not be us ed unless absolut ely necessary.
Use of improper extension cord could resultin a risk of fire and
electric shock. If extension cord must be used, make sure:

a. That pins on plug of extension cord are the sam e number, size,

and shape as those of plug on charger;

b. That extension cord is properly wired and in good electrical

condition; and

c. That wire size is large enough for ac ampere rating of charger.

4. Do not operate charger with damaged cord or plug - replace the
cord or plug immediately.

5. Do not operate charger if it has received a sharp blow, been
dropped, or otherwise damaged in any way; take it to a

qualified serviceman.

6. Do not disassemble charger; take it to a qualified serviceman when
service or repair is required. Incorrect reassembly

may result in a risk of electric shock or fire.

7. To reduce risk of electric shock, unplug charger from outlet before
attempting any maintenance or cleaning. Turning

off controls will not reduce this risk.

8. WARNING - RISK OF EXPLOSIVE GASES

a. WORKING IN VICINITY OF A LEAD-ACID BATTERY IS

DANGEROUS. BA TT ERIES GENERATE EXPLOSIVE GASES

DURING NORMAL BATTERY OPERATION. FOR THIS

REASON, IT IS OF UTMOST IMPORTANCE THAT EACH TIME

BEFORE USING YOUR CHARGER, YOU READ THIS MANUAL

AND FOLLOW THE INSTRUCTIONS EXACTLY.

b. To reduce risk of battery explosion, f ollow these instructions and

those published by battery manufacturer and

manufacturer of any equipment you intend to use in vicinity of

battery. Review cautionary marking on these

products and on engine.

9. PERSONAL PRECAUTIONS

a. Someone should be within range of your voice or close enough to

come to your aid when you work near a lead-acid
battery.
b. Have plenty of fresh water and soap nearby in cas e battery acid

contacts skin, clothing, or eyes.
c. Wear complete eye protection and clothing protection. Avoid

touching eyes while working near battery.
d. If battery acid contacts skin or clothing, wash immediately with

soap and water. If acid enters eye, immediately
flood eye with running cold water for at least 10 minutes and get

medical attention immediately.
e. NEVER smoke or allow a spark or flame in vicinity of batt ery or

engine.
f. Be extra cautious to reduce risk of dropping a metal tool onto

battery. It might spark or short-circuit battery or other
electrical part that may cause explosion.
g. Remove personal metal items such as rings , brac elets, necklaces ,

and watches when working with a lead-acid
battery. A lead-acid battery can produce a short-circuit current

high enough to weld a ring or the like to metal,
causing a severe burn.
h. Use charger for charging a LEAD-ACID battery only. It is not

intended to supply power to a low voltage electrical
system other than in a starter-motor application. Do not use

battery charger for charging dry-cell batteries that are
commonly used with home appliances. These batteries may burst

and cause injury to persons and damage to
property.
i. NEVER charge a frozen battery.

10. CHARGER LOCATION
a. Locate charger as far away from battery as dc cables permit.
b. Never place charger directly above battery being charged; gases

from battery will corrode and damage charger.
c. Do not operate charger in a closed-in area or restrict ventilation in

any way.
d. Do not set a battery on top of charger.

-3-

LED

STATUS

OUTPUT

VOLTAGE

CONDITION

*NOTES

Off

No Output

Output Shorted

Off

No Output

Battery Voltage

below 3Volts

2

Red

(blinking)

Vbatt 3-7Volts

typ.

Charging

1 & 2

Red

Vbatt 7-13Volts

typ.

Charging full Amps

(1 or 2A)

Yellow

Vbatt 13.0 -

13.5Volts

Charging < 70% full

Amps

(OR not connected)

Off No Output Charger not plugged

Green Vbatt 13.5Volts Battery fully charged
Green

(blinking)

*NOTES:

1. Vbatt is the battery voltage

2. Battery overly discharged; may not fully charge.

3. LED may blink momentarily if the above connection procedure is not
followed.

Vbatt >

13.5Volts

Check for incorrect

in

battery

3

Always keep your internal AGM battery fully charged.
Plug your Battery Doc® Charger/Maintainer into any 110
volt outlet after each use. Battery Doc®
Charger/Maintainer will not over charge the battery.

External Battery Information (optional)

BATTERY OPERATING INSTRUCTIONS

The JIFFY STX PROII LECTRIC requires a 12 volt, deep cycle, lead
acid battery. Jiffy recommends an AGM battery.

The power source should be chosen carefully. The battery directly
affects the performance of the drill. A battery that is too small or in
poor condition will reduce power and cycle time.

The battery should be fully charged before every use. This will
ensure maximum performance from bot h your JIFFY LECTRIC power
ice drill and the battery.

Replacement Blade

Improper cutting may be due to dull or damaged drill teeth or drill point.
Maintain sharp blade teeth and point. Preserve the original factory
cutting angles when sharpening your drill. File blade teeth and use a
disk sander to sharpen the point. For professional service see your
Jiffy service center. Only genuine

Jiffy blade teeth are to be used.

JIFFY® LECTRIC™ STX PROII ICE DRILL –

PARTS LIST

Ref. Part No.
No. No. Description Used

1 4155 Cover 1
2 1719 Locknut 2
3 4289 Machine Screw 2
4 3810 Motor 1
5 3918 Wire Assembly 1
6 4261 Battery 1
7 4265 Wire Assembly 1
8 2512 Push Nut 2
9 3961 Switch 1
10 3968 “U” Handle 1
11 4270 Throttle Clip 1
12 4150 Throttle Assembly 1
13 4152 Switch Mounting Bracket 1
14 4266 Wire Assembly 1
15 2451 Locknut 2
16 4151 Battery Holder 1
17 4156 Hex Capscrew 2
18 3946 Handle Plate 1
19 4153 Battery Clamp 1
20 3921 Motor Mounting Plate 1
21 1683 Hex Capscrew 1
22 1689 Flat Washer 8
23 1119 Lock Washer 1
24 4154 Plug Bracket 1
25 4267 Cable Asbly w/ Connector 1
26 3965 “L” Handle 1
27 2355 Hex Capscrew 4
28 3922 Locknut 6
29 4269 Machine Screw 2
30 2336 Locknut 2
31 3351 Hex Capscrew 2

Blade Replacement Instructions

When replacing blade teeth, the beveled edge of teeth and the head of
the capscrews should face the ice. The stamped part number on the
teeth should face away from the ice, as shown in the diagram. Use
two 7/16” wrenches to remove the capscrews and to retighten after
replacement. CAUTION – THE BLADE TEETH ARE SHARP AND

SHOULD BE HANDLED CAREFULLY TO AVOID FLESH CUTS OR
INJURY.

-4-