JIAXING GLEAD ELECTRONICS JLBM4 User Manual

客户名称：
我司料号：
贵司料号：
软件版本：

嘉兴佳利电子股份有限公司

规格承认书

Spec for approval

承认签章

佳利承认 客户承认

拟制 审核 批准 拟制 审核 批准

地址：

总公司：浙江省嘉兴市经济开发区塘汇工业园区正原路一号；
深圳分公司：深圳市福田区车公庙泰然工业园区 213 栋 4 楼 C 座

第 1 页，共 9页

嘉兴佳利电子股份有限公司

ZYM-BT42 Module

CSR BC417143B

Rev.1.0

May 2011

Device Features

•

Bluetooth Spec v2.0+EDR Compliant

Class 2, up to 10-meter range

•

•

Complete 2.4GHz Bluetooth® System

•

Power management: low power 1.8V operation for Bluetooth® core

•

Compact size: 26.9mm (L) x 13 (W) mm x 2.2mm (H)
Bluetooth® Profile Supported: SPP,HSP, HFP, OPP,PBAP

•

Internal antenna

•

On-board flash memory (8Mbits)

•

•

Support multiple connections
Surface mount module for embedded applications

•

Several firmware options

•

•

Rewritable flash memory for easy upgrade route
Custom firmware production available

•

General Description

The BT42 V1 module from GLEAD is a complete Bluetooth® solution.It is built on CSR BC04-Ext ernal
Core and 8Mbit Flash memory.It’s a short range,compact and cost effective module. Be able to be embedded
into your any electronics devices which need Bluetooth® connection,such as industry handle devices,PND,

HID applications…

The BT42 V1 module is a power class2 Bl ue tooth® device, and is in compliance w i th version 2.0+EDR of

the Bluetooth® specification. It includes CSR BC04-External Core and 8Mbit Flash memory, internal attenna,
supporting circuitry, together with some higher-level software protocols and applications such as L2CAP, SDP,
GAP, HSP, HFP, OPP and PBAP resided in the flash memory.

Applications

•

Industry handle device
Printer

•

•

Personal Navigation Device
PDAs and other portable terminals

•

MP3 headset

•

第 2 页，共 9页

嘉兴佳利电子股份有限公司

ID:A8S-JLBM4" any

The User Guidelines about FCC Rules

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

Changes or modifications not expressly approved by the part responsible for compliance could void the

user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. The equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct interference by one or more of the
following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help.

Please notice that if the FCC identification number is not visible when the module is installed inside another
device, then the outside of the device into which the module is installed must also display a label referring to the
enclosed module. This exterior label can use wording such as the following: " Contains FCC ID:A8S-JLBM4" any

similar wording that expresses the same meaning may be used.

第 3 页，共

9

页