Jiangmen Yuanmeidao Technology REMOTEAIR User Manual
REMOTE AIR 3 产品手册
（PD2-N1/N2/N3）
马达示意图
齿轮
天线接口
(ANTENNA)
REMOTE
12～18V
OLED显示屏
OFF/ON
CHANNEL
PD3-R正面示意图 PD3-R背面示意图
齿轮
REMOTE
12～18V
OFF/ON
CHANNEL
PD3-M正面示意图 PD3-M背面示意图
U形夹
U形夹
重要说明：使用本产品前,请仔细阅读使用说明，掌握REMOTE AIR 3的
使用方法。
了解更多：可以在 http://www.pdmovie.com.cn上找到更多信息、观
看视频以及了解有关 REMOTE AIR 3功能的详细信息。
支持：REMOTE AIR 3享有免费的程序升级和一年的硬件保修期限,这
些服务可在PDMOVIE经销商处获得，或直接联系PDMOVIE。
联系方式：Email：pd@pdmovie.com
如需技术支持,请随时拔打：+86 13500282830/+86 13672905004
更多动态,资讯敬请留意官方网站：www.pdmovie.com.cn
马达状态指示灯
马达状态指示灯
控制器示意图
天线接口
(ANTENNA)
FOCUS焦点控制手轮
FOCUS
FOCUS功能按钮
FOCUS焦点控制手轮
IRIS光圈 推拉拔杆指示灯
IRIS光圈 推拉拔杆
IRIS光圈 推拉拔杆
ZOOM变焦 推拉拔杆
PD2-NT控制器正面示意图
ZOOM
ZOOM变焦 推拉拔杆
PD2-NT控制器侧面示意图
PD2-NT控制器侧面示意图
FOCUS焦点控制手轮指示灯
IRIS光圈 推拉拔杆指示灯
ZOOM变焦 推拉拔杆指示灯
控制器状态指示灯
FOCUS焦点控制手轮
ZOOM变焦 推拉拔杆指示灯
CHANNEL
OFF/ON
IRIS
开、关/频道切换按钮
IRIS功能按钮
1/4螺丝孔
5Vin
控制器显示屏
8、检测镜头行程 长按控制器的FOCUS功能按钮三秒自动检测镜头行程
；如果是连接APP使用，长按APP控制界面右下角的“AUTO框”也可以
自动检测镜头行程；使用PD2-N2或PD2-N3时多个马达会同时自检。
9、两种操控方式 控制方式一：转动控制器上的控制手轮和推动推拉拔杆
即可控制相对应的马达。控制方式二：连接APP使用时，可通过滑动APP的
：需要连接APP使用前,先打开
控制界面内，相对应的通道栏控制马达。（
注
APP内SET界面里的HELP选项，学习如何使用APP。每次启动APP也会有
相应的使用教程供您观看学习）
控制器按钮使用说明
按钮/接口 功能 操作说明
OFF/ON
CHANNEL
FOCUS
ZOOM
IRIS
功能按钮
ZOOM
IRIS
功能按钮
ANTENNA
开机、关机
切换信号频道
自动检测镜头行程
切换控制通道
镜头行程限位
（AB点）
改变马达转动方向
切换控制速度
调换ZOOM和IRIS
当前的控制通道
长按两秒出现开关机画面后松手
短按一下
长按三秒待镜头转动后松手
短按两下功能按键
短按第一下设置A点，转动控制转
轮到理想位置，再次短按一下设置
设置
B点。此时控制器通道指示灯会闪
烁白色。
撤消
短按一下取消已设置好的AB点行程
快速短按七下功能按键
快速短按五下,ZOOM/IRIS功能按键;
指示灯常亮时：慢速
指示灯慢速闪烁时：中速
指示灯快速闪烁时：高速
快速短按三下,ZOOM/IRIS功能按键;
适合左右手切换使用
天线接口
5V充电输入5Vin
FOCUS通道默认为最快控制
速度；只有ZOOM和IRIS可
以切换速度。
3 4 5
使用说明
1、安装马达 将马达安装在19MM或15MM（使用转接环）导管上，同时
将马达齿轮卡住镜头齿轮。
2、连接马达
使用PD2-N1时，直接将D-Tap电源线6针插头连接PD3-R的REMOTE
12~18V(6孔插座），将D-Tap插头连接V-mount电源DC输出插座；
使用PD3-N2时，先将串联马达线（6针）连接PD3-R的REMOTE 12~18V
与PD3-M的REMOTE12~18V，再将D-Tap线6针插头连接PD3-M的
REMOTE12~18V，D-Tap插头连接V-mount电源DC输出插座；
使用PD3-N3时，先将一条串联马达线连接PD3-R的REMOTE12~18V与
PD3-M1的REMOTE12~18V；再将另一条串联马达线连接PD3-M1的
REMOTE12~18V与PD3-M2的REMOTE12~18V；最后将D-Tap线6针插
头连接PD3-M2的REMOTE12~18V，D-Tap插头连接V-mount电源DC输
出插座。如下图所示：
3、安装天线 从包装箱内取出天线，分别安装在控制器ANTENNA与接
收马达ANTENNA上。
4、启动控制器和马达 长按控制器的ON/OFF按钮两秒，待显示屏亮后
松手；长按马达底部OFF/ON按钮两秒待接收马达显示屏亮或马达背后指
示灯亮后松手。
1
马达按钮/接口使用说
按钮/接口 操作说明功能
OFF/ON
CHANNEL
ANTENNA
REMOTE
12～18
开机、关机
切换信号频道
信号传输与供电通用接口，支持12~18V宽电压供电
长按两秒出现开关机画面后松手
短按一下
天线接口
通道指示灯颜色介绍
控制器和马达通道
指示灯颜色
红色
绿色
蓝色
黄色
青色
紫色
目前只使用红色FOCUS通道、ZOOM通道、IRIS通道。备用通道1、2、3用
作未来产品功能扩展储备。若不小心切换到备用通道，双击功能按钮切换回来
即可。（可参考控制器按钮/接口使用说明表）
当控制器通道指示灯一直闪烁白色时，表示该通道已被设置AB点行程限位。单
击该通道指示灯相应的功能按钮即可取消AB点行程限位。（可参考控制器按
钮/接口使用说明表）
对应控制通道
FOCUS/焦点
ZOOM/变焦
IRIS/光圈
备用通道1
备用通道2
备用通道3
对应控制部件
控制手轮
推拉拔杆
推拉拔杆
控制手轮
推拉拔杆
推拉拔杆
控制器状态指示灯说明
指示灯颜色
控制器状态
红色 绿色
常规使用 常规充电连接蓝牙使用 连接蓝牙充电
蓝色 青色
5、设置信号频道 查看控制器与接收马达OLED屏的显示信息，检查
控制器和接收马达是否设置在同一个信号频道上。短按控制器的
OFF/ON按钮和马达的OFF/ON一下可各自切换信号频道，连接成功后
，控制器和接收马达均会显示信号强度数值。
控制器显示屏显示信息：
C
显示当前频道，可通过短按Channel键一下调节；
显示控制器与接收马达连接成功后的信号强度；
T
R
显示控制器电池剩余电量百分比；
显示接收马达电量；
蓝牙连接成功图标
接收马达显示屏显示信息：
Channel
Singnal Level
TX
RX
显示当前频道，可通过短按Channel键一下调节；
显示控制器与接收马达连接成功后的信号强度；
显示控制器电池剩余电量百分比；
显示接收马达电量；
6、连接APP 先开启iPhone/iPod touch的蓝牙功能，再打开程序
“REMOTE AIR”，REMOTE AIR打开后，它会自动搜索并匹配已启动
的控制器。当手机通知栏的蓝牙图标开始闪烁时，表示正在搜索蓝牙设备
；当蓝牙图标呈现黑色时，表示已连接，此时程序会自动进入操控界面。
蓝牙连接后，控制器的屏幕会出现蓝牙图标，蓝牙信号灯也由红色变为绿
色。(APP可在苹果应用商店处搜索PDMOVIE/REMOTE AIR进行下载）
此项为扩展功能,如只需常规使用，可跳过此项。
7、设置控制通道 控制器的控制手轮和推拉拔杆都有相对应的功能按钮
和通道指示灯。双击FOCUS功能按钮将控制手轮指示灯设置为红色，双
击ZOOM和IRIS功能按钮将两个推拉拔杆指示灯分别设置为绿色和蓝色
。马达也有通道指示灯，双击马达底部的OFF/ON按钮将安装好的马达
指示灯颜色也相对应地设置为FOCUS红色、ZOOM绿色、IRIS蓝色控制
通道。(可参考控制器和马达按钮使用说明表；指示灯通道颜色介绍表;)
补充说明
1、REMOTE AIR 3有三种不同规格的齿轮(0.4M、0.5M、0.6M),根据镜头的齿模选
择合适的规格，用3MM六角匙松开螺丝并替换。(标准配置0.8M,其他规格需订购);
2、紧急停止功能：由于马达螺母未拧紧等原因，在自检过程中可能出现马达齿轮不停
空转的现象，只需短按一下马达底部ON/OFF键，马达会立即紧急停止（注意：紧急
停止PD3-R时，信号频道也会同时切换);
3、马达还有手动检测镜头行程的功能：首先马达要安装好，并且卡好在镜头齿轮上。
然后启动马达，启动后，手动转动镜头的焦点、变焦、光圈FOCUS/ZOOM/IRIS往前
转尽，此时马达会自动记录镜头行程的起点；再手动转动镜头的焦点、变焦、光圈
FOCUS/ZOOM/IRIS往后转尽，此时马达会自动记录镜头行程的终点；最后将镜头转
回中间，即完成行程检测；
4、当您使用控制器控制马达无反应的情况下，建议检查几个点：
①、查看控制器是否于接收马达处于同一个信号频道；
②、查看控制器的通道指示灯和马达的通道指示灯颜色是否一致；
③、使用前是否有进行镜头行程检测；
④、是否不经意设置了AB点行程限位；
5、APP与控制器连接时，APP会通过蓝牙自动搜索并配对控制器,在重启控制器时，
APP也需退出并重新启动，通过蓝牙重新配对控制器。
6、控制器背部有2个1/4螺丝孔，可用于安装监视器、iPhone/iPod Touch 夹具等
设备；
7、关于充电：
①、控制器OLED屏内TX值显示电池剩余电量百分比；
②、控制器正常使用的情况下，续航时间可长达48小时；
③、在控制器电量不足时,可使用移动电源通过USB充电线为控制器充电;
④、关于电池保养：长期不使用时，建议每隔一段时间就检查一次控制器,保证电池有
足够电量；长期低电量或者无电量的状态，会使电池内部对电子移动的阻力越来越大,
导致电池容量变小;理想的状态是让电池的电量处于中间状态;
6、关于设备保存：电子元件在环境相对湿度大于60%就容易受潮,同时容易滋生霉菌,
有可能使工作不正常,为了保护REMOTE AIR 3不受过于潮湿环境影响,在长时间未使
用的情况下,应放入防潮箱或干燥箱内保存,将相对湿度控制在35-45％;
2
REMOTE AIR 3 Product Manual
C
T
R
Cancel
Press for two seconds to turn ON / OFF
controller
（PD2-N1/N2/N3）
Motor
Antenna
Connector
REMOTE
12～18V
OLED monitor
Important
Please read this document, master REMOTE AIR PRO usage,Before you first
useyour REMOTE AIR 3
Learn more
You can find more information, watch demos, and learn even more about
REMOTE AIR 3 features at www.pdmovie.com/remoteairpro/.
Support
REMOTE AIR 3 enjoy free upgrade program and one year of hardware warranty
period, you can get these services from PDMOVIE dealer.
Contact
MAIL:pd@pdmovie.com
Facebook:Pdmovie
WEB:www.pdmovie.com
Gears
U clamp
OFF/ON
CHANNEL
PD3-R Front Sketch Map PD3-R Back Sketch Map
Gears
REMOTE
12～18V
U clamp
OFF/ON
CHANNEL
PD3-M Front Sketch Map
PD3-M Back Sketch Map
Indicator light
for motor
Indicator ligh
Contoller
(IRIS) Pull-push lever
Antenna
Connector
Focus function button
(Focus) Control Wheel
Light for IRIS pull-push lever
8.Calibration
Press the FOCUS function button at the controller and hold up to 3 seconds, the
calibration will be done automatically. If you connect with the App, just press the
AUTO button at the right bottom up to 3 seconds. All motors will be calibrated same
time when you are using PD2-N2 or PD2-N3.
9.Two ways of controlling
1. Turn the wheel and the pull-push levers to controller the correspondent motors.
2. When you use with the App, you can control by slide in the app to control the
correspondent motors. (PS: The HELP in the app will teach you how to use it. Or
you can watch the teaching video every time you start the app)
(ZOOM) Pull-push lever
(Focus) Control Wheel
PD2-NT
ZOOM
FOCUS
(ZOOM) Pull-push lever
Zoom function button
PD2-NT Side
(IRIS) Pull-push lever
IRIS function button
PD2-NT Side
Suitable for the switch the left and right hand
button Function Instructions
OFF/ON
CHANNEL
Turn ON/OFF
Changing Channel
Automatic Calibrating
Changing
Control Channel
FOCUS
ZOOM
IRIS
ZOOM
IRIS
AB point
Motor forward and
reverse switching
Switch the speed
Switch channel for
ZOOM and IRIS
ANTENNA
Lights for focus control wheel
Light for Iris pull-push lever
1/4Hanging
Strap
5Vin
Light for Zoom pull-push lever
Light for controller status
Front Sketch Map
(Focus) Control Wheel
Light for Zoom pull-push lever
Sketch Map
CHANNEL
OFF/ON
IRIS
OFF/ON
CHANNEL
Sketch Map
Short press once
Press 3 seconds till the lens is
rotating then let go
OLED monitor
Press quickly twice
Press once quickly to set A point, turn
the wheel to where you want and then
set B point by press once quickly
Set
again. When the lights flashing by
white then the AB point is settled.
Push once quickly to cancel the
settled AB point.
Press quickly seven times
Press quickly five times
FOCUS is set with fastest speed by default
The lights always on: slowest speed
The lights flash slowly: middle speed
The lights flash quickly: quickest speed
Press quickly for three times
Suitable for the switch the left
and right hand
Antenna connector
5Vcharging input5Vin
3 4 5
Instruction manual
1、Motor Installation
The motor is mounted on 19 mm or 15 mm rods. For 15 mm rods use the included
19 to 15 mm rod adaptor.
2、Connecting Motors
When using PD2-N1 (Single Channel):
1).Connect the D-Tap power cable 6-pin aviation locking plug directly to the PD3-R
REMOTE 12 ~ 18V input.
2).Then connect the D-Tap plug to a pro battery or similar power source with a D-Tap
output.
When using the PD2-N2 (Dual Channel):
1).Connect the motor cable (6-pin) from the PD3-R REMOTE 12 ~ 18V connector to
the PD3-M REMOTE12 ~ 18V connector.
2).Connect the D-Tap to 6-pin aviation locking plug to PD3-M REMOTE12 ~ 18V and
connect the D-Tap plug to a pro battery or similar power source with a D-Tap output.
When using PD2-N3 (Triple Channel):
1).Connect one Motor Drive Line Cable to the PD3-R REMOTE12 ~ 18V connector
and the PD3-M1 REMOTE12 ~ 18V connector.
2).Connect second Motor Drive Line Cable to the PD3-M1 REMOTE12 ~ 18V
connector and the PD3-M2 REMOTE12 ~ 18V connector.
3).Connect the D-Tap to 6-pin plug to the PD3-M2 REMOTE12 ~ 18V connector and
Then connect the D-Tap plug to a pro battery or similar power source with a D-Tap
output.
3. Installing the Antennas
Three antennas are included in the package. Install one on the hand control
unit. Install one on the PD3-R Receiver Motor. The third antenna is an extra.
4. Powering On
To power on the Hand Controller Unit, press the OFF / ON button on the bottom
of the unit for two seconds until the screen lights up. To power on the motor,
press the ON / OFF button on the bottom for two seconds until the indicator
lights up.
1
Manual for buttons/ connectors on the motors
Button
OFF/ON
CHANNEL
ANTENNA
REMOTE
12～18
Function
Turn ON/OFF
Changing Channel
Signal and power supply common interface, supports power
supplies with 12 ~ 18V voltage range
Instructions
Press for two seconds to turn ON / OFF
motors
Short press once
Antenna connector
Introduction for the channel lights
The color for the
channel lights on
controller and motors
RED
GREEN
BLUE
YELLOW
CYAN
PURPLE
For now only FOCUS, ZOOM, IRIS channel is using.Spare channel
1, 2, 3 is for future products expand only.If change to spare channel
by accident, press the function button twice to switch back(See
Specification for controller button/connectors)
When the lights flashing in white, it means the AB point has been set up.
Press the correspondent function button once, AB point will be canceled.
(See Specification for controller button/connectors)
Correspondent channels
FOCUS
ZOOM
IRIS
Spare channel 1
Spare channel 2
Spare channel 3
Correspondent parts
(Focus) Control Wheel
(Zoom) Pull-push lever
(IRIS) Pull-push lever
(Focus) Control Wheel
(Zoom) Pull-push lever
(IRIS) Pull-push lever
Control Unit Status Indicator Lights
Indicator
Status
RED
Unit is
powered on
GREEN
Unit is powered
on and synched
with your device
via Bluetooth
BLUE
Unit is
charging
CYAN
Unit is synced
via Bluetooth and
being charged at
the same time
5.Set the Channel
Check the info at the OLED monitor on the controller and mastermotor to see
if they are at the same signal channel. Press ON/ OFF button quickly on the
controller and master motor, you can change the channel. After it is connected,
both controller and motor will show the data of the signal.
How to read the info on the OLED monitor from the controller
The signal strength of controller and mater motor
connected successfully
Shows current Channel in use, short press on
OFF/ON Channel button to change channel
The controller battery charge remaining percentage
Receiver voltage
Bluetooth connected successfully
How to read the info on the OLED monitor from the master motor
Channel
Singnal Level
TX
RX
6.Connect the App
Turn on the Bluetooth at your iPhone/ iPod touch, start the app”REMOTE AIR”
, it will search and match the controller automatically. It is searching the device
when the bluetooth icon is flashing; it is connected if the icon turn dark. Then
you can see the control interface. After the bluetooth is connected successfully,
you can see the bluetooth icon from the OLED monitor at the controller, the
light will turn from red to green. (You can download the app at app store by
searching keyword of PDMOVIE/ REMOTE AIR)
This function is for expand use. Just pass this if you just need regular use.
7.Set control channel
There are correspondent function button and channel lights for the wheel and
push-pull levers.Press the function button at FOCUS quickly for twice, the
controller lights can be turned to red. Press the function button at ZOOM/ IRIS
quickly for twice, the lights can be turned on green and blue. There are also
channel lights for the motors. Press the ON/OFF button quickly twice at the
bottom of the motors, the lights can be set as FOCUS(red), ZOOM(green),
IRIS(blue).
Supplementary instruction
1)There are 3 different gears for REMOTE AIR 3(0.4M, 0.5M, 0.6M),
Choose the suitable one according to the different lenses and replace
by 3MM hexagon wrench. (Standard configuration is 0.8M, other size
need extra order.)
2)Emergency stop: Some reasons like the motors screws are not
tightened enough will cause the gears no stop running during calibration.
Only need to press the ON/OFF button at the bottom of the motors.
3)The calibration can be made manually: Firstly you need to install the
motors and align the gear at the camera gear. Start the motors, then
turn the iris, zoom or focus to one end manually, then turn the 3 channels
to the other end, the motors will record the start and end automatically.
Then the calibration is finished.
4)If the motors got no response when you use the controller, please
check below:
①please check if the controller and master motor with same signal channel
②please check if the channel lights are fit with motors lights
③please check if the calibration is done or not
④please check if the AB point is set
5)When the app connect with the controller, it will search and match the
controller automatically. When you restart the controller, you need to
restart the app and rematch to the controller as well.
6)There are 2 1/4 screw holes to install the monitor, iPhone/ iPod Touch
clap etc
7)How to charge:
①The TX in the OLED monitor of the controller means how much power left.
②Under normal usage, the power can last for 48 hours.
③You can use power bank to charge the controller by USB when the
power is not enough.
④About how to keep the battery long life use: If you will not use the
device for a long time, we suggest you can check your controller once
in a while to make sure the power is full. It will do harm for the battery if
it is no power or low power situation for a long time. It’s best to make the
power in a middle status.
8)How to preserve the device: Electronic elements will be affected with
damp and mildewed under the relative humidity is over 60%. It might
cause problems for the device. Pls keep REMOTE AIR 3 into our case or
any moisture-proof box so that the humidity can between 35-45%
The signal strength of controller and mater motor
connected successfully
Shows current Channel in use, short press on
OFF/ON Channel button to change channel
The controller battery charge remaining percentage
Receiver voltage
2
Loading...