JHS8 Electrical (Australia) Pty Ltd
User’s Manual
Inverter Portable Air Conditioner
Model No: A002BPY-18KR/A
Thank you for choosing super quality air conditioner. Please be sure to read
this user’s manual carefully before using the machine. Any problem, please
contact the professional service for help.
2
CONTENTS
IMPORTANT SAFEGUARDS….............................................................................3
PLACEMENT AND INSTALLATION…...............................................................4
PARTS NAME….......................................................................................................6
CONTROL PANEL…...............................................................................................7
SCREEN….................................................................................................................8
OPERATION METHODS…....................................................................................8
REMOTE CONTROL….........................................................................................10
WATER DRAINAGE…...........................................................................................12
MAINTENANCE….................................................................................................12
TROUBLE SHOOTING….....................................................................................13
3
IMPORTANT SAFEGUARDS
Please read following safeguards carefully before using the machine:
● This machine just for domestic use, please don’t use it in any other places.
● Please use this machine indoor not outdoor, and place it in a dry environment.
● Don’t use the machine when any damage in power cord, plug or machine itself.
Any damage, please contact professional serviceman for help. If need to lengthen
power cord, extended cord can be used, but please don’t let the power cord scatter on the
work area.
● Please make the machine far from heat sources and power supply , and avoid direct
sunlight.
● Please turn-off the machine first before pull out the plug.
● Please pull out the plug when the machine is under cleaning, parts-replacement or leaving
unused.
● Please clean the machine based on the instruction in user’s manual.
● Please make sure using voltage meet requirements, the damages caused by
connection error is out of the scope of warranty.
● Don’t let little children touch the machine.
● Don’t run the machine when no one there, even if a short leave, please turn-off it.
● Don’t tug power cord when pulling out plug or moving the machine.
● Don’t put the machine on a place with water or other liquid.
● Don’t spatter water or oil into machine.
● Don’t put hard objects between fan blades.
● Don’t repair the machine by yourself. Dealing with problems by non-professional
person may cause danger, even power cord replacement must be done by professional
electrician.
● Only use accessories from suppliers, otherwise danger and damages of the machine
may be caused .
Note :
● Place the machine on flat ground, and keep it far from around things at least 50cm.
● Make sure the socket can be reached from machine location.
● Keep the machine stand upright so that compressor can work well.
● Don’t run the machine near to gasoline or any other flammable liquids.
● Make sure free access of air-inlet and air-outlet.
● Don’t use spraying agent (such as pesticides , paint) or other flammable materials, otherwise
plastic deformation, or even electric damage of the machine may be caused.
Power supply
● Make sure no damage in plug.
● Don’t use connector instead of plug.
● Insert plug into socket first, then turn on socket switch , press key “POWER” to run machine.
Please safekeep this user’s manual.
Placement and Installation
Placement
● Place the machine on flat and dry ground, and keep it far from around things at least 50cm.
(fig.1)
Installation
●
●
Put slide bar connector into adjustable slide bar, adjust window open width in order slide bar
match window well, and the length of slide bar is adjustable. (fig.2)
（fig.1）
4
Spin slide bar connector into exhaust hose first, then spin the exhaust hose into exhaust connector.
（fig.2）
5
Installation Errors
● Free access of exhaust pipe is important, installation errors will bring bad influence of
machine. (fig.3)
● Avoid exhaust-pipe with sharp bend.
● Make sure air in exhaust pipe can run smoothly .
(fig.3)
Warning
Length of exhaust pipe according to the machine features, please don’t replace or lengthen it
freely, otherwise errors will be easily caused.
Note: extreme length of unfolding exhaust pipe is 1500mm, please shorten the length as
much as possible and keep it level as much as possible when installing .
Parts Name
1. Air-outlet
2. Control Panel
3. Screen
4. Castor
Front side
6
Back Side
5. Filter frame upper
6. Power Cord Location
7. Filter frame lower
8. Plug cap
9. Exhaust Pipe
10. Handle
11. Exhaust Connector
Check packing accessories, read user’s manual to get how to use them. (fig.4)
1. Exhaust hose 2. Ajustable slide bar 3. Slide bar connector 4. Remote control
5. Active carbon filter(optional)
Control Panel
TiO2/Ion Timer Sleep Up DOWN Fan Mode Power
1. POWER: press this key to turn on/off machine. After machine turns on, default value is
cooling mode with low fan speed.
2. MODE:
after machine turns on, press this key to select cooling, dehumidifying and fan mode.
3. FAN: after machine turns on, press this key to select fan speed (high ,medium and low).
4. DOWN: under cooling mode, press this key to downward setting temperature from
16~31℃
.
7
5. UP: under cooling mode, press this key to upward temperature from 16~31℃.
6. SLEEP: under cooling mode, press this key to turn on/off sleeping function.
7. TIMER: under power-on or standby mode, press this key to setup on/off time from 1~24.
8. TiO2/Ion: after machine turns on, for TiO2/Ion model ,press this key to select TiO2/Ion
function.
Screen
1. Temperature display
2. Cooling mode indicator
3. Dehumidifying mode indicator
4. Fan mode indicator
5. Sleeping mode indicator
6. Timer mode indicator
7. Receiver
8. Water full indicator
9. Low fan speed
10. Medium fan speed
11. High fan speed
12. Ion / TiO2 indicator (only for Ion /TiO2 model)
Operation Methods
Cooling mode
● After machine turns on, default value is cooling mode with 22℃ and low fan speed.
● Press “ MODE” to select cooling mode, cooling mode indictor turns on .
● Press “ UP” or “ DOWN” to adjust temperature ( from 16~31℃).
● Press “ FAN” to select fan speed(low, medium ,high)
Fan mode
● Press “ MODE” to select fan mode, fan mode indicator turns on .
● Press “ FAN” to select fan speed(low, medium ,high)
● Temperature and sleeping function cannot be setup.
Timer mode
● Under standby mode, press “TIMER” to setup the power-on time. Timer indicator turns on.
● Under power-on mode, press “TIMER” to setup power-off timer.. Timer indicator turns on.
8
Dehumidifying mode
● Press “MODE” to select dehumidifying mode, dehumidifying mode indicator turns on .
● Under dehumidifying mode, sleeping function cannot be setup, and fan speed is low.
Sleeping mode
● Press key “SLEEP” enter into sleeping mode, default value of fan speed is low.
● When sleeping mode turns on , under cooling mode, the first one hour later, setting
temperature will go up 1℃, the second one hour later, setting temperature will go up
another 1℃, and then keep the same .
● Sleeping mode is invalid under dehumidifying and fan mode. Under water full, machine
standby and mode conversion, sleeping mode will be cancelled .
Inverter technology function
● Inverter technology for fast and efficient cooling
The compressor’s working frequency according to the different value between the setting
temperature and ambient temperature, the smaller the different value is,the lower the
frequency and power comsuption will be, the bigger the different value
is ,the higher the
frequency and power comsuption will be.
● Press “ ” and “ ” key at the same time to see The compressor’s working frequency .
Compressor protection
● Three minutes later after power on / restart, compressor starts to run.
Remote Control
1. Power
2. Timer
3. Down
4. Mode
5. Up
6. Fan
7. Sleeping
8.TiO2&Ion(only for TiO2 / Ion model )
9
Installation of the carbon filter (Optional)
1. Remove the side filter
frame from the unit.
2. Remove the back filter
frame from the unit.
3. Separate the filter fixer
from the back filter frame.
4. Remove the active carbon
filter from its plastic bag.
5. Insert the active carbon
filter into the filter frame.
6. Fix the filter by
re-assembling the fixer
onto the filter frame.
7. Re-fit the back filter frame
inside the unit.
8. Re-fit the side filter frame
inside the unit.
10
Water Drainage
This machine with auto-water-evaporating system. Condensed-water cycle to
cool down the condenser, which will not only improve cooling efficiency, but also
save energy.
● If inner water tank is full, “ ” will flashed on the screen , machine enter into standby mode,
buzzer shouts , compressor stops and all keys is invalid till machine recovers to be normal .
● Pull out the plug to drain out water, power off the machine and restart it , the machine will runs
normally .
Maintenance
Note: in order to avoid electric shocks, please power-off the machine and pull out
plug before maintenances or repairs.
Cleaning
● Please pull out plug before cleaning .
● Use soft semi-dry cloth to clean the machine. Don’t use chemical agents, such as benzene,
alcohol, gasoline and so on ; otherwise the machine surface will be damaged, or even the
machine itself.
● Don’t spatter water into the machine .
Filter
● Clean the filters every two weeks, if filters are blocked by dust, machine efficiency will be
reduced .
● Clean the filters in warm water with neutral detergent, then dry the cleaned filters on a shady
place.
Note: Don’t run the machine without filters.
Season Cleaning
If the machine will be unused for a long time, please do as following :
● Pull out drainage plug upper / lower to flow out water.
● Let the machine runs under fan mode for 2 hours to dry out the machine internal
● Turn off machine and pull out plug .
● Clean and dry filters , then reinstall them .
● Pull out exhaust pipe for safekeeping .
● Put the machine into plastic bag , and place it on a dry place.
11
Trouble Shooting
Please contact professional serviceman without delay in following situation
noituloS esuaC elbuorT
Power off Power on Machine cannot
work
water-full indicator turns on Drain water out
Direct sunlight Draw the curtains
Door and windows are open ,
many heat sources
in the room .
Close the door and windows, move
out heat sources.
Filters are too dirty. Clean or replace filters
Machine
auto-restarts
frequently
Air-inlet or air out-let
is blocked
Remove blockage
Too noisy
Machine is not put on flat
ground.
Place it on flat and solid ground,
avoiding shaking
Compressor
cannot work
Compressor time-delay
protection turns on
Wait for 3 minutes, then restart the
machine after temperature reduces .
Note: when abnormal situations are occurred, turn off machine and pull out plug, then contact
With professional electrician for help .
THE DISPOSAL OF ELECTRICAL AND ELECTRONIC EQUIPMENT WASTE PRODUCTS ON THE
PART OF FINAL USERS IN THE EUROPEAN UNION”
This symbol on the product or on the container indicates that this product cannot be
eliminated with the general waste. The user is responsible for eliminating this kind of waste
by throwing them away at a “recycling point” specifically for electrical and electronic waste.
Selective collection and electrical equipment recycling contribute to preserve natural
resources and warrant waste recycling to protect environment and health. In order to
receive further information about electrical and electronic waste collecting and recycling,
contact your Local Council, the service of household waste or the establishment where the
product was acquired.
12
Loading...