JETWAY S450, S450L User Manual

Download

S450/S450L

USER'S MANUAL

M/B For Socket 478 Pentium 4 Processor

NO. G03-S450R2A

Release date: December 2001

Trademark:

* Specifications and Information contained in this documentation are furnished for information use only, and are

subject to change at any time without notice, and should not be construed as a commitment by manufacturer.

USER’S NOTICE..............................................................................ii

MANUAL REVISION INFORMATION .............................................1

COOLING SOLUTIONS..................................................................1

CHAPTER 1 INTRODUCTION OF S450/S450L MOTHERBOARD

1-1 FEATURE OF MOTHERBOARD............................................................... 2

1-2 SPECIFICATION..........................................................................................3

1-3 PERFORMANCE LIST ................................................................................ 4

1-4 LAYOUT DIAGRAM & JUMPER SETTING...........................................5

CHAPTER 2 HARDWARE INSTALLATION

2-1 HARDWARE INSTALLATION STEPS.....................................................7

2-2 CHECKING MOTHERBOARD'S JUMPER SETTING ..........................7

2-3 INSTALL CPU ...............................................................................................8

2-3-1 GLOSSARY ........................................................................................8

2-3-2 ABOUT INTEL PENTIUM 4 478-PIN CPU....................................9

2-4 INSTALL MEMORY .................................................................................... 9

2-5 EXPANSION CARD......................................................................................10

2-5-1 PROCEDURE FOR EXPANSION CARD INSTALLATION..................10

2-5-2 ASSIGNING IRQ FOR EXPANSION CARD............................................

2-5-3 INTERRUPT REQUEST TABLE FOR THIS MOTHERBOARD..........

2-5-4 AGP SLOT .....................................................................................................

2-6 CONNECTORS, HEADERS ........................................................................12

2-6-1 CONNECTORS .............................................................................................

2-6-2 HEADERS......................................................................................................15

2-7 STARTING UP YOUR COMPUTER.......................................................... 18

CHAPTER 3 INTRODUCING BIOS

3-1 ENTERING SETUP.......................................................................................19

3-2 GETTING HELP............................................................................................20

3-3 THE MAIN MENU ........................................................................................20

3-4 STANDARD CMOS FEATURES.................................................................21

3-5 ADVANCED BIOS FEATURES ..................................................................23

3-6 ADVANCED CHIPSET FEATURES ..........................................................25

3-6-1 DRAM TIMING SETTINGS............................................................25

3-6-2 AGP FUNCTION SETTINGS.......................................................... 26

3-7 INTEGRATED PERIPHERALS..................................................................26

3-7-1 ONCHIP IDE FUNCTION................................................................27

3-7-2 ONCHIP DEVICE FUNCTION....................................................... 28

3-7-3 ONCHIP SUPER IO FUNCTION.................................................... 29

3-8 POWER MANAGEMENT SETUP..............................................................30

3-8-1 PM WAKE UP EVENTS.................................................................. 31

3-9 PNP/PCI CONFIGURATION SETUP.........................................................32

TABLE OF CONTENT

3-9-1 IRQ RESOURCES ............................................................................ 33

3-10 PC HEALTH STATUS.................................................................................33

3-11 MISCELLANEOUS CONTROL ................................................................ 34

3-12 LOAD STANDARD/OPTIMIZED DEFAULTS .......................................35

3-13 SET SUPERVISOR/USER PASSWORD................................................... 35

CHAPTER 4 DRIVER & FREE PROGRAM INSTALLATION

MAGIC INSTALL SUPPORTS WINDOWS 95/98/98SE/NT4.0/2000 .............36

4-1 AGPVXD

INSTALL SIS AGPVXD DRIVER

...........................................37

4-2 VGA

INSTALL SIS 650 VGA DRIVER

...........................................38

4-3 SOUND

INSTALL ALC201 AUDIO CODEC DRIVER

.........................39

4-4 LAN

INSTALL SIS 900 PCI FAST ETHERNET DRIVER

...............40

(ONLY FOR S450L)

4-5 PC-HEALTH

WINBOND HARDWARE DOCTOR MONITORING SOFTWARE

4-6 MAGIC BIOS

INSTALL BIOS LIVE UPDATE UTILITY

................................42

4-7 PC-CILLIN

INSTALL PC-CILLIN2000 ANTI-VIRUS PROGRAM

.............43

4-8 HOW TO DISABLE ON-BOARD SOUND.................................................45

4-9 HOW TO UPDATE BIOS.............................................................................45

USER’S NOTICE

COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED, TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER.

THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE S450/S450L MOTHERBOARD AND WE DO ASSURE THIS MANUAL MEETS U SER’S REQUIREMEN T BU T WILL CHANGE, CORRECT ANY TIME WITHOUT NOTICE. MANUFACTURER PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, AND WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTIAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMANGES FOR LOSS OF PROFIT, LOSS OF BUSINESS, LOSS OF USE OF DATA, INTERRUPTION OF BUSINESS AND THE LIKE).

PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES, AND THEY ARE USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER’S BENEFIT, WITHOUT INTENT TO INFRINGE.

Manual Revision Information

Reversion Revision History Date

2.0 Second Edition December 2001

Item Checklist

5 S450/S450L motherboard 5 Cable for IDE/Floppy 5 Cable for VGA Connector 5 CD for motherboard utilities

□

Cable for USB Port 3/4, 5/6 (Option)

5 S450/S450L User’s Manual

Intel Pentium 4 Processor Family

Cooling Solutions

As processor technology pushes to faster speeds and higher performance, thermal management becomes increasingly crucial when building computer systems. Maintaining the proper thermal environment is key to reliable, long-term system operation. The overall goal in providing the proper thermal environment is keeping the processor below its specified maximum case temperature. Heatsinks induce improved processor heat dissipation through increased surface area and concentrated airflow from attached fans. In addition, interface materials allow effective transfers of heat from the processor to the heatsink. For optimum heat transfer, Intel recommends the use of thermal grease and mounting clips to attach the heatsink to the processor. When selecting a thermal solution for your system, please refer to the website below for collection of heatsinks evaluated and recommended by Intel for use with Intel processors. Note, those heatsinks are recommended for maintaining the specified Maximum T case requirement. In addition, this collection is not intended to be a comprehensive listing of all heatsinks that support Intel processors.

For vendor list of heatsink and fan, please visit : http://developer.intel.com/design/Pentium4/components/index

Chapter 1

Introduction of S450/S450L Motherboard

1-1 Feature of motherboard

The S450/S450L motherboard is design for use Intel Pentium 4 Processor in 478 Pin Package Processor with the SiS 650 Chipset delivers a high performance and professional desktop platform solution. Which utilize the Socket 478 design and the memory size expandable to

2.0GB.

These motherboards use the newest SiS 650 Chipset Supports 400MHz System Bus in data transfer rate and 100MHz/133MHz clock frequency, support DDR200/ DDR266 DDR SDRAM Module. And use SiS 961 MuTIOL Media IO supports 533MB/s transfer data from/to sub-system to/from the Muti-threaded I/O Link Encoder/Decoder in SiS 961.

These motherboards offer ULTRA ATA

100

to provide speedier HDD throughout that boosts

overall system performance.

The S450L motherboard including LAN controller support 10/100 Mb/sec BASE T transfer rate Ethernet.

These motherboards also has an integrated AC’97 2.1 CODEC on board which is fully compatible with Sound Blaster Pro that gives you the best sound quality and compatibility.

The S450/S450L integrated High Performance & High Quality 3D Accelerator supports UltraAGPII with 2GB/s bandwidth, built-in MPEG-2/1 Video Decoder and Video Accelerator supports VCD.DVD HDTV decoding and playback, supports graphic and video overlay function. Built-in programmable 24-bit true-color RAMDAC up to 333MHz pixel clock. Programmable frame buffer size from 8MB and up to 64MB. For those wanting even greater graphic performance, an AGP 4X slot is included on the board, support AGP 2X/4X capability and Fast write Transaction.

With USB control as well as capability of expanding to 6 USB function ports delivering 2x12Mb/s bandwidth and rich connectivity, the S450/S450L meet future USB demand also this motherboard has built-in hardware monitor function to monitor and protect your computer. These motherboards also

integrated Recovery Genius in BIOS

to protect your hard disk from

virus infect hard disk data.

A useful software tool “Magic BIOS” examines the BIOS version automatically with the correct version available on the web, links the site for users to download the latest version of BIOS and updates the BIOS. Use “Magic BIOS”, users can download and update BIOS automatically and completed under the OS easily.

S450/S450L provides high performance & meets future specification demand. It is really wise choice for your computer.

1-2 Specification

Spec Description

Design

∗

Micro ATX form factor 4 layers PCB size: 22x24.4cm

Chipset

∗

SiS 650 North Bridge Chipset

∗

SiS 961 MuTIOL Media I/O Chipset

CPU Socket

(mPGA478B Socket)

∗

Support Intel Pentium 4 478 Pin package utilizes Flip-

Chip Pin Grid Array (FC-PGA2) package processor

∗

Support 1.5G∼2.2G 478 Pin Pentium 4 processor

∗

Reserves support for future Intel Pentium 4 processors

Memory Socket

∗

184-pin DDR SDRAM module socket x2

∗

Support 2 pcs DDR200/DDR266 DDR SDRAM Modules

∗

Expandable to 2.0GB

Expansion Slot & Headers

∗

AGP slot x1 support AGP 2.0 & 4X mode

∗

32-bit PCI slot x3

∗

CNR slot x1

Integrate IDE

∗

Two PCI IDE controllers support PCI Bus Mastering, ATA PIO/DMA and the ULTRA DMA 33/66/100 functions that deliver the data transfer rate up to 100 MB/s

LAN (Only for S450L)

∗

SiS On-chip LAN controller

∗

Support full duplex 10/100 Base-T Ethernet

Audio

∗

AC’97 Digital Audio controller integrated

∗

AC’97 Audio CODEC on board

∗

Audio driver and utility included

BIOS

∗

Award 2Mb Flash ROM

Multi I/O

∗

PS/2 keyboard and PS/2 mouse connectors

∗

Floppy disk drive connector x1

∗

Parallel port x1

∗

Serial port x2

∗

USB connector x2

∗

USB headers x4 (connecting cable option)

∗

Audio connector (Line-in, Line-out , MIC & Game Port)

1-3 Performance List

The following performance data list is the testing result of some popular benchmark testing programs. These data are just referred by users, and there is no responsibility for different testing data values gotten by users (the different Hardware & Software configuration will result in different benchmark testing results.)

Performance Test Report

CPU:

Intel Pentium 4 1.9GHz mPGAB package

DRAM:

256MB DDR266 x1 (MICRON 46V16M8-6)

VGA Expansion Card:

NVDIA Geforce2 MX-200 32MB (1024x768xHi-color)

Hard Disk Driver:

IBM DTLA-305040 (ATA-100)

BIOS:

Award Optimal default

OS:

Win 98SE

Performance Test Report

DDR266

On Board VGA

Share 32MB

DDR266

Geforce MX200

32MB 3D Mark 2000 3297 2918 3D Mark 2001 1407 1201 3D Winbench 2000 51.8 55.3 Final Reality 10.59 9.63 Content Creation Winstone 2000 41.1 42.7 Content Creation Winstone 2001 51.8 51.9 Business Winstone2001 41.4 43.7

Winbench 99:

CPU Mark 99 107 110 FPU Winmark 99 6590 6580 Business Disk Winmark99 5090 7020 Hi-end Disk Winmark99 17000 21600 Business Graphic Winmark 383 402 Hi-end Graphic Winmark 1160 1250

SYS Mark 2000/2001 : SISMark 2000/2001 Rating (Internet Content Creation / Office Productivity)

SISMark 2000 201 (220/188) 208 (224/196) SISMark 2001 147 (167/129) 147 (167/129)

SISOFT Sandra 2001 :

Dhrystone ALU MIPS 3625 3627 Whetstone FPU MFLOPS 1142/2363 1140/2359 Int ALU/RAM MB/S 929 880 Float FPU/RAM MB/S 944 905 Integer SSE2 IT/S 7543 7536 Floating-Point SSE2 IT/S 9322 9314 QUAKE3 DEMO1 FPS 71.0 115.0 DEMO2 FPS 68.0 116.0

WCPUID System/CPU Clock 100.67/1912.80 100.67/1912.81

1-4 Layout Diagram & Jumper Setting

CIR Connector

CNR Slot

Front Panel Audio

PC99 Back Panel

CD Audio

PCI Slot

AGP Slot

K/B Power ON Jumper (JP10)

Floppy Connector

SiS 650 Chip

Front Panel Connector

Clear CMOS (JP6)

ATX Power Conn.

USB2 Port

CPU FAN

2MBit Flash ROM BIOS

CPU Socket

DDR SDRAM DIMM X2

System FAN1

Wake On LAN

System FAN2

SiS 961 Chip

ATX 12V Power Conn.

USB Port

/LAN Connector

(for S450L)

PS2 KB/Mouse Port

ATX P9 Power Conn.

PS/2 MOUSE

COM1 COM2

PS/2 Keyboard

USB

LINE-OUT

LINE-IN

MIC

PRINT GAME/MIDI PORTLAN

ITE 8705 Chip

ATA 100 IDE Conn.

USB1 Port

IR Connector

VGA Connector

Jumpers

Jumper Name Description Page

JP6 CMOS RAM Clear 3-pin Block P.7

JP10 Keyboard Power On Enable/Disabled 3-pin Block P.8

Connectors

Connector Name Description Page

ATXPWR ATX Power Connector 20-pin Block P.12 ATX12V ATX 12V Power Connector 4-pin Block P.12 ATXP9 ATX P9 Power Connector 6-pin Block P.12 KB/MS PS/2 Mouse & PS/2 Keyboard

Connector

6-pin Female P.13

CN4 USB Port Connector 4-pin Connector P.13

CN2 LAN Port Connector RJ-45 Connector (for S450L) P.13

PRINT Parallel Port Connector 25-pin Female P.13 GAME Audio/Game Connector 3 phone jack + 15-pin Connector P.13 COM1/COM2 Serial Port COM1/2 Connector 9-pin Connector P.13 FDD Floppy Driver Connector 34-pin Block P.13 IDE1/IDE2 Primary/Secondary IDE Connector 40-pin Block P.14

Headers

Header Name Description Page

VGA VGA Connector 2x8-pin Block P.15 AUDIO SPEAKER, MIC header 9-pin Block P.15 USB1/USB2 USB Port Headers 9-pin Block P.15 HD-LED IDE activity LED 2-pin Block P.15 RESET Reset switch lead 2-pin Block P.16 SPEAK PC Speaker connector 4-pin Block P.16 PWR-LED Power LED 2-pin Block P.16 PWR-BTN Power switch 2-pin Block P.16 WOL Wake On-LAN Headers 3-pin Block P.16 SFAN1, SFAN2, CPUFAN

FAN Headers 3-pin Block P.16

IR IR infrared module Headers 5-pin Block P.17 CD_IN CD Audio-In Headers 4-pin Block P.17

Expansion Sockets

Socket/Slot Name Description Page

ZIF Socket 478 Pin CPU Socket 478-pin mPGA CPU Socket P.9 D I M M 1 , D I M M 2 SDRAM Module

Socket

184-pin DDR SDRAM Module Expansion Socket

P.10

PCI1 ∼ PCI3

PCI Slot 32-bit PCI Local Bus Expansion slots P.11 AGP AGP 4X Mode Slot AGP Expansion Slot P.11 CNR CNR Slot Communication Network Riser Slot

Chapter 2

Hardware installation

2-1 Hardware installation Steps

Before using your computer, you had better complete the following steps:

1. Check motherboard jumper setting

2. Install CPU and Fan

3. Install System Memory (DIMM)

4. Install Expansion cards

5. Connect IDE and Floppy cables, Front Panel /Back Panel cable

6. Connect ATX Power cable

7. Power-On and Load Standard Default

8. Reboot

9. Install Operating System

10. Install Driver and Utility

2-2 Checking Motherboard’s Jumper Setting

(1) CMOS RAM Clear (3-pin) : JP6

A battery must be used to retain the motherboard configuration in CMOS RAM short 2-3 pins of JP6 to store the CMOS data.

To clear the CMOS, follow the procedure below:

1. Turn off the system and unplug the AC power

2. Remove ATX power cable from ATX power connector

3. Locate JP6 and short pins 1-2 for a few seconds

4. Return JP6 to its normal setting by shorting pins 2-3

5. Connect ATX power cable back to ATX power connector

Note: When should clear CMOS

1. Troubleshooting

2. Forget password

3. After over clocking system boot fail

CMOS RAM Clear Setting

1-2 closed Clear CMOS

JP6

2-3 closed Normal (Default)

(2) Keyboard Power On function Enabled/Disabled: JP10

When setting Enabled you can using keyboard by key in password to power on system.

JP10

Keyboard Power On Setting

2-3 closed K/B Power ON Enabled1-2 closed K/B Power O N Disable

(Default)

2-3 Install CPU

2-3-1 Glossary

Chipset (or core logic) - two or more integrated circuits whi ch control the i nterfaces bet ween the system processor, RAM, I/O devises, and adapter cards.

Processor slot/socket - the slot or socket used to mount the system processor on the motherboard.

Slot (AGP, PCI, ISA, RAM) - the slots used to mount adapter cards and system RAM. AGP - Accelerated Graphics Port - a high speed interface for video cards; runs at 1X

(66MHz), 2X (133MHz), or 4X (266MHz). PCI - Peripheral Component Interconnect - a high speed interface for video cards, sound

cards, network interface cards, and modems; runs at 33MHz. ISA - Industry Standard Architecture - a relatively low speed interface primarily used for

sound cards and modems; runs at approx. 8MHz.

Serial Port - a low speed interface typically used for mouse and external modems. Parallel Port - a low speed interface typically used for printers. PS/2 - a low speed interface used for mouse and keyboards. USB - Universal Serial Bus - a medi um speed interface typically used for mouse, keyboards,

scanners, scanners, and some digital cameras. Sound (interface) - the interface between the sound card or integrated sound connectors and

speakers, MIC, game controllers, and MIDI sound devices.

LAN (interface) - Local Area Network - the interface to your local area network. BIOS (Basic Input/Output System) - the program logic used to boot up a computer and

establish the relationship between the various components. Driver - software, which defines the characterist ics of a device for use by another device or

other software. Processor - the "central processing unit" (CPU); the principal integrated circuit used for doing

the "computing" in "personal computer"

Front Side Bus Frequency -

the working frequency of the motherboard, which is generated

by the clock generator for CPU, DRAM and PCI BUS.

CPU L2 Cache -

the flash memory inside the CPU, normal it depend on CPU type.

2-3-2 About Intel Pentium 4 478-pin CPU

This motherboard provides a 478-pin surface mount, Zero Insertion Force (ZIF) socket, referred to as the mPGA478B socket supports Intel Pentium 4 processor in the 478 Pin package utilizes Flip-Chip Pin Grid Array (FC-PGA2) package technology.

The CPU that comes with the motherboard should have a cooling FAN attached to prevent overheating. If this is not the case, then purchase a correct cooling FAN before you turn on your system.

WARNING!

Be sure that there is sufficient air circulation across the processor’s heatsink and CPU cooling FAN is working correctly, otherwise it may cause the processor and motherboard overheat and damage, you may install an auxiliary cooling FAN, if necessary.

To install a CPU, first turn off your system and remove its cover. Locate the ZIF socket and open it by first pulling the level sideways away from the socket then upward to a 90-degree angle. Insert the CPU with the correct orientation as shown below. The notched corner should point toward the end of the level. Because the CPU has a corner pin for two of the four corners, the CPU will only fit in the orientation as shown.

CPU ZIF mPGAB Socket

Colden Arrow

mPGA478B

When you put the CPU into the ZIF socket. No force require to insert of the CPU, then press the level to Locate position slightly without any extra force.

2-4 Install Memory

This motherboard provides two 184-pin DUAL INLINE MEMORY MODULES (DIMM) sites for DDR memory expansion available from minimum memory size of 64MB to maximum memory size of 2.0GB DDR SDRAM.

Valid Memory Configurations

Bank 184-Pin DIMM Total Memory

Bank 0, 1 (DDR1) DDR200/DDR266

DDR SDRAM Module

X1 64MB∼1.0GB

Bank 2, 3 (DDR2) DDR200/DDR266

DDR SDRAM Module

X1 64MB∼1.0GB

Total System Memory (Max. 2.0GB) 2 64MB∼2.0GB

Generally, installing DDR SDRAM modules to your motherboard is very easy, you can refer to figure 2-4 to see what a 184-Pin DDR SDRAM module looks like.

DDR2 (BANK2+ BANK3)

DDR1 (BANK0+ BANK1)

NOTE!

When you install DIMM module fully into the DIMM socket the eject tab should be locked into the DIMM module very firmly and fit into its indention on both sides.

WARNING!

For the DDR SDRAM CLOCK is set at 133MHz, use only DDR266compliant DDR Modules. When this motherboard operate at 133Mhz, most system will not even boot if non-compliant modules are used because of the strict timing issues, if your DDR Modules are not DDR266-compliant, set the SDRAM clock to 100MHz to ensure system stability.

2-5 Expansion Cards

WARNING!

Turn off your power when adding or removing expansion cards or other system components. Failure to do so may cause severe damage to both your motherboard and expansion cards.

2-5-1 Procedure For Expansion Card Installation

1. Read the documentation for your expansion card and make any necessary hardware or software setting for your expansion card such as jumpers.

2. Remove your computer’s cover and the bracket plate on the slot you intend to use.

3. Align the card’s connectors and press firmly.

4. Secure the card on the slot with the screen you remove above.

5. Replace the computer system’s cover.

6. Set up the BIOS if necessary.

7. Install the necessary software driver for your expansion card.

2-5-2 Assigning IRQs For Expansion Card

Some expansion cards need an IRQ to operate. Generally, an IRQ must exclusively assign to one use. In a standard design, there are 16 IRQs available but most of them are already in use.

Figure 2-4

Standard Interrupt Assignments

IRQ Priority Standard function

0 N/A System Timer 1 N/A Keyboard Controller 2 N/A Programmable Interrupt 3 * 8 Communications Port (COM2) 4 * 9 Communications Port (COM1) 5 * 6 Sound Card (sometimes LPT2) 6 * 11 Floppy Disk Controller 7 * 7 Printer Port (LPT1) 8 N/A System CMOS/Real Time Clock

9 * 10 ACPI Mode when enabled 10 * 3 IRQ Holder for PCI Steering 11 * 2 IRQ Holder for PCI Steering 12 * 4 PS/2 Compatible Mouse Port 13 N/A Numeric Data Processor 14 * 5 Primary IDE Channel 15 * 1 Secondary IDE Channel

* These IRQs are usually available for ISA or PCI devices.

2-5-3 Interrupt Request Table For This Motherboard

Interrupt request are shared as shown the table below:

INT A INT B INT C INT D INT E INT F INT G INT H

Slot 1

√

Slot 2

√

Slot 3

√

Onboard USB 1

√

Onboard USB 2

√

AC97/MC97

√

LAN

√

IMPORTANT!

If using PCI cards on shared slots, make sure that the drivers support “S ha re d IRQ” or that the cards don’t need IRQ as si gn m en t s. C o nf l ic t s will arise between the two PCI groups that will make the system unstable or cards inoperable.

2-5-4 AGP Slot

This motherboard provides an AGP Slot, support the 2X/4X AGP VGA card.

AGP SLOT

2x notch 4x notch

2-6 Connectors, Headers

2-6-1 Connectors

(1) Power Connector (20-pin block) : ATXPWR

ATX Power Supply connector. This is a new defined 20-pins connector that usually

comes with ATX case. The ATX Power Supply allows to use soft power on momentary switch that connect from the front panel switch to 2-pins Power On jumper pole on the motherboard. When the power switch on the back of the ATX power supply turned on, the full power will not come into the system board until the front panel switch is momentarily pressed. Press this switch again will turn off the power to the system board.

PIN ROW2 ROW1

1 3.3V 3.3V 2 -12V 3.3V 3 GND GND 4 Soft Power On 5V 5 GND GND 6 GND 5V 7 GND GND 8 -5V Power OK 9 +5V +5V (for Soft Logic) 10 +5V +12V

Pin 1

(2) ATX 12V Power Connector (4-pin block) : ATX12V

This is a new defined 4-pins connector that usually comes with ATX Power Supply. The

ATX Power Supply which fully support Pentium 4 processor must including this connector for support extra 12V voltage to maintain system power consumption. Without this connector might cause system unstable because the power supply can not provide sufficient current for system.

Pin 1

(3) ATX P9 Power Connector (6-pin block) : ATXP9

This is a new defined 6-pins connector that usually comes with ATX Power Supply. The ATX Power Supply which fully support Pentium 4 processor must including this connector for support extra 3.3V and 5V voltage to maintain system power consumption. Without this connector might cause system unstable because the power supply can not provide sufficient current for system.

Power Plugs from Power SupplyPower Connector on Motherboard

BLK BLK BLK

ORG ORG

RED

GND GND

GND

3.3V

3.3V 5V

(4) PS/2 Mouse & PS/2 Keyboard Connector: KB/MS

The connectors for PS/2 keyboard and PS/2 Mouse.

(5) USB Port connector: CN4

The connectors are 4-pin connector that connect USB devices to the system board.

(6) LAN Port connector (RJ45): CN2 (Only for S450L)

This connector is standard RJ45 connector for Network connector.

(7) Parallel Port Connector (25-pin female): PRINT

Parallel Port connector is a 25-pin D-Subminiature Receptacle connector. The Onboard Parallel Port can be disabled through the BIOS SETUP. Please refer to Chapter 3 “INTEGRATED PERIPHERALS SETUP” section for more detail information.

(8) Audio and Game Connector : GAME

This Connector are 3 phone Jack for LINE-OUT, LINE-IN, MIC and a 15-pin D-Subminiature Receptacle Connector for joystick/MIDI Device.

Line-out :

Audio output to speaker

Line-in :

Audio input to sound chip

MIC :

Microphone Connector

Game/MIDI :

For joystick or MIDI Device

(9) Serial Port COM1, COM2 : COM1, COM2

COM1, COM2 are the 9-pin D-Subminiature mail connector. The On-board serial port can be disabled through BIOS SETUP. Please refer to Chapter 3 “INTEGRATED PERIPHE R ALS SETUP” section for m o r e detail information.

(10) Floppy drive Connector (34-pin block): FDD

This connector supports the provided floppy drive ribbon cable. After connecting the single plug end to motherboard, connect the two plugs at other end to the floppy drives.

PS/2

Keyboard

COM1 COM2 USB

PS/2

MOUSE

LINE-OUT

LINE-IN

MIC

PRINT GAME/MIDI PORT LAN

Pin 1

Flo

ppy

Drive Connector

(11) Primary IDE Connector (40-pin block): IDE1

This connector supports the provided IDE hard disk ribbon cable. After connecting the

single plug end to motherboard, connect the two plugs at other end to your hard disk(s). If you install two hard disks, you must configure the second drive to Slave mode by setting its jumpers accordingly. Please refer to the documentation of your hard disk for the jumper settings.

Primary IDE Connector

Pin 1

(12) Secondary IDE Connector (40-pin block): IDE2

This connector connects to the next set of Master and Slave hard disks. Follow the

same procedure described for the primary IDE connector. You may also configure two hard disks to be both Masters using one ribbon cable on the primary IDE connector and another ribbon cable on the secondary IDE connector.

Secondary IDE Connector

Pin 1

•

Two hard disks can be connected to each connector. The first HDD is referred to as the “Master” and the second HDD is referred to as the “Slave”.

•

For performance issues, we strongly suggest you don’t install a CD-ROM or DVD-ROM drive on the same IDE channel as a hard disk. Otherwise, the system pe rf orm an ce o n t hi s channel may drop.

2-6-2 Headers

(1) VGA Connector (2x 8-pin) : VGA

VGA Connector

VGA

1516

(2) Line-Out/MIC Header for Front Panel (9-pin): AUDIO

This header connect to Front Panel Line-out, MIC connector with cable. Without install the cable, this header default setting is 5-6 short, 9-10 short. When you

install the cable you have take off these jumpers.

Line-Out, MIC Headers

UDIO

Pin 1

AUD_MIC

UD_FPOU

T_L

AUD_MIC_BIAS

AUD_FPOUT_R

UD_GND

AUD_RET_L

UD_RE

HP_ON

AUD_VCC

9 10

(3) USB Port Headers (9-pin) : USB1/USB2

These headers are used for connecting the additional USB port plug. By attaching an option USB cable, your can be provided with two additional USB plugs affixed to the back panel.

USB Port Headers

Pin 1

USB1

VCC

DATA

GND

+ DATA

VCC

DATA

GND

+ DATA

USB Port Headers

Pin 1

USB2

VCC

DATA

GND

+ DATA

VCC

DATA

GND

+ DATA

OC (Over Current)

(4) IDE Activity LED: HD-LED

This connector connects to the hard disk activity indicator light on the case.

(5) Reset switch lead: RESET

This 2-pin connector connects to the case-mounted reset switch for rebooting your computer without having to turn off your power switch. This is a preferred method of rebooting in order to prolong the lift of the system’s power supply. See the figure below.

(6) Speaker connector: SPEAK

This 4-pin connector connects to the case-mounted speaker. See the figure below.

(7) Power LED: PWR-LED

The Power LED is light on while the system power is on. Connect the Power LED from the system case to this pin.

(8) Power switch: PWR-BTN

This 2-pin connector connects to the case-mounted power switch to power ON/OFF the system.

System Case Connections

SPEAK

SPKR

GND

VCC5

Pin 1

JW_FP1

Pin 1

RESET

PWRBT

HDLED

VCC5

HDDLED

ACPILED

PWRB TN

GND

ACPILED

VCC 5

RSTSW

GND

(9) Wake On-LAN Headers (3-pin) : WOL

This connector connects to a LAN card with a WAKE ON-LAN output. This connector power up the system when a wake up signal is received through the LAN/Modem card.

NOTE:

This feature requires that Wake On LAN or Ring In Wake up is enabled.

Wake-On-LAN Headers

WOL

5VS B

GND

WON

(10) FAN Headers (3-pin) : SFAN1, SFAN2, CPUFAN

These connectors support cooling fans of 350mA (4.2 Watts) or less, depending on the fan manufacturer, the wire and plug may be different. The red wire should be positive, while the black should be ground. Connect the fan’s plug to the board taking into consideration the polarity of connector.

SFAN1

CPUFAN

SFAN2

FAN Speed Headers

(11) IR infrared module Headers (5-pin) : IR

This connector supports the optional wireless transmitting and receiving infrared module. You must configure the setting through the BIOS setup to use the IR function.

IR infrared module Headers

Pin 1

GND IRRX

VCC 5

IRTX

(12) CD Audio-In Headers (4-pin) : CD_IN

CD_IN are the connectors for CD-Audio Input signal. Please connect it to CD-ROM CD-Audio output connector.

CD Audio-In Headers

CD_I N

2-7 Starting Up Your Computer

1. After all connection are made, close your computer case cover.

2. Be sure all the switch are off, and check that the power supply input voltage is set to proper position, usually in-put voltage is 220V∼240V or 110V∼120V depending on your country’s voltage used.

3. Connect the power supply cord into the power supply located on the back of your system case according to your system user’s manual.

4. Turn on your peripheral as following order: a. Your monitor.

b. Other external peripheral (Printer, Scanner, External Modem etc…) c. Your system power. For ATX power supplies, you need to turn on the power supply

and press the ATX power switch on the front side of the case.

5. The power LED on the front panel of the system case will light. The LED on the monitor may light up or switch between orange and green after the system is on. If it complies with green standards or if it is has a power standby feature. The system will then run power-on test. While the test are running, the BIOS will alarm beeps or additional message will appear on the screen.

If you do not see any thing within 30 seconds from the time you turn on the power. The system may have failed on power-on test. Recheck your jumper settings and connections or call your retailer for assistance.

Beep Meaning

One short beep when displaying logo No error during POST Long beeps in an endless loop No DRAM install or detected One long beep followed by three short

beeps

Video card not found or video card memory bad

High frequency beeps when system is working

CPU overheated System running at a lower frequency

6. During power-on, press <Delete> key to enter BIOS setup. Follow the instructions in BIOS SETUP.

Power off your computer:

You must first exit or shut down your operating system before switch off the power switch. For ATX power supply, you can press ATX power switching after exiting or shutting down your operating system. If you use Windows 9X, click

“Start”

button, click

“Shut down”

and then click

“Shut down the computer?”

The power supply should turn off after windows shut down.

Chapter 3

Introducing BIOS

The BIOS is a program located on a Flash Memory on the motherboard. This program is a bridge between motherboard and operating system. When you start the computer, the BIOS program gain control. The BIOS first operates an auto-diagnostic test called POST (power on self test) for all the necessary hardware, it detects the entire hardware device and configures the parameters of the hardware synchronization. Only when these tasks are completed done it gives up control of the computer to operating system (OS). Since the BIOS is the only channel for hardware and software to communicate, it is the key factor for system stability, and in ensuring that your system performance as its best.

In the BIOS Setup main menu of Figure 3-1, you can see several options. We will explain these options step by step in the following pages of this chapter, but let us first see a short description of the function keys you may use here:

•

Press <Esc> to quit the BIOS Setup.

•

Press

↑↓←→

(up, down, left, right) to choose, in the main menu, the option you

want to confirm or to modify.

•

Press <F10> when you have completed the setup of BIOS parameters to save these parameters and to exit the BIOS Setup menu.

•

Press Page Up/Page Down or +/– keys when you want to modify the BIOS parameters for the active option.

3-1 Entering Setup

Power on the computer and by pressing <Del> immediately allows you to enter Setup. If the message disappears before your respond and you still wish to enter Setup, restart the system to try again by turning it OFF then ON or pressing the “RESET” button on the system case. You may also restart by simultaneously pressing <Ctrl>, <Alt> and <Delete> keys. If you do not press the keys at the correct time and the system does not boot, an error message will be displayed and you will again be asked to

Press <F1> to continue, <Ctrl-Alt-Esc> or <Del> to enter Setup

3-2 Getting Help

Main Menu

The on-line description of the highlighted setup function is displayed at the bottom of the screen.

Status Page Setup Menu/Option Page Setup Menu

Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window, press <Esc>.

3-3 The Main Menu

Once you enter Award BIOS CMOS Setup Utility, the Main Menu (Figure 3-1) will appear on the screen. The Main Menu allows you to select from fourteen setup functions and two exit choices. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu.

Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status

Miscellaneous Control Load optimized Defaults Load Standard Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving

Esc : Quit

↑↓→ ←

: Select Item

F10 : Save & Exit Setup

Time, Date, Hard Disk Type...

Figure 3-1

Standard CMOS Features

Use this Menu for basic system configurations.

Advanced BIOS Features

Use this menu to set the Advanced Features available on your system.

Advanced Chipset Features

Use this menu to change the values in the chipset registers and optimize your system’s performance.

Integrated Peripherals

Use this menu to specify your settings for integrated peripherals.

Power Management Setup

Use this menu to specify your settings for power management.

PnP/PCI configurations

This entry appears if your system supports PnP/PCI.

PC Health Status

This entry shows your PC health status.

Miscellaneous Control

Use this menu to specify your settings for Miscellaneous control.

Load Optimized Defaults

Us e this menu to load the BIOS default values these are setting for op ti ma l pe rf or ma nc es system operations for performance use.

Load Standard Defaults

Use this menu to load the BIOS default values for the stable performance system operation that are factory settings for normal use.

Set Supervisor/User Password

Use this menu to set User and Supervisor Passwords.

Save & Exit Setup

Save CMOS value changes to CMOS and exit setup.

Exit Without Saving

Abandon all CMOS value changes and exit setup.

3-4 Standard CMOS Features

The items in Standard CMOS Setup Menu are divided into several categories. Each category includes no, one or more than one setup items. Use the arrow keys to highlight the item and then use the <PgUp> or <PgDn> keys to select the value you want in each item.

Standard CMOS Features

Date (mm:dd:yy) Mon, Oct, 26 2001 Time (hh:mm:ss) 16 : 48 : 35

Item Help

> IDE Primary Master Press Enter None > IDE Primary Slave Press Enter None > IDE Secondary Master Press Enter None > IDE Secondary Slave Press Enter None

Drive A 1.44M, 3.25 in. Drive B None

Video EGA/VGA Halt On All,But Keyboard

Base Memory 640K Extended Memory 56320K Total Memory 57344K

Menu Level >

Change the day, month, year and century

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

Date

The date format is <day><month><date><year>.

Day

Day of the week, from Sun to Sat, determined by BIOS. Read-only.

Month

The month from Jan. through Dec.

Date

The date from 1 to 31 can be keyed by numeric function keys.

Year

The year depends on the year of the BIOS.

Time

The time format is <hour><minute><second>.

Primary Master/Primary Slave Secondary Master/Secondary Slave

Press PgUp/<+> or PgDn/<–> to select Manual, None, Auto type. Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category. If your hard disk drive type is not matched or listed, you can use Manual to define your own drive type manually. If you select Manual, related information is asked to be entered to the following items. Enter the information directly from the keyboard. This information should be provided in the documentation from your hard disk vendor or the system manufacturer. If the controller of HDD interface is SCSI, the selection shall be “None”. If the controller of HDD interface is CD-ROM, the selection shall be “None”

Access Mode

The settings are Auto Normal, Large, and LBA.

Cylinder

number of cylinders

Head

number of heads

Precomp

write precomp

Landing Zone

landing zone

Sector

number of sectors

3-5 Advanced BIOS Features

Advanced BIOS Features

Item Help

Anti-Virus Protection Disabled CPU L1 & L2 Cache Enabled CPU L2 Cache ECC Checking Disabled Quick Power On Self Test Enabled First Boot Device Floppy Second Boot Device HDD-0 Third Boot Device CDROM Boot Other Device Enabled Swap Floppy Drive Disabled Boot Up Floppy Seek Enabled Boot Up NumLock Status On Gate A20 Option Fast Typematic Rate Setting Disabled Typematic Rate (Chars/Sec) 6 Typematic Delay (Msec) 250 Security Option Setup OS Select For DRAM > 64MB Non-OS2 HDD S.M.A.R.T. Capability Disabled Report No FDD For Windows Yes Video BIOS Shadow Enabled

Menu Level >

Allows you to choose the VIRUS warning feature for IDE Hard Disk boot sector protection. If this function is enabled and someone attempt to write data into this area, BIOS will show a warning message on screen and alarm beep Enabled copies Video BIOS to shadow RAM Improves performance

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

Anti-Virus Protection

Allows you to choose the VIRUS Warning feature for IDE Hard Disk boot sector protection. If this function is enabled and someone attempt to write data into this area, BIOS will show a warning message on screen and alarm beep.

Disabled

(default) No warning message to appear when anything attempts to access the

boot sector or hard disk partition table.

Enabled

Activates automatically when the system boots up causing a warning message to appear when anything attempts to access the boot sector of hard disk partition table.

CPU L1 Cache

The default value is Enabled.

Enabled

(default) Enable cache

Disabled

Disable cache

Note: The internal cache is built in the processor.

CPU L2 Cache

Choose Enabled or Disabled. This option enables the Level 2 cache memory.

Quick Power On Self Test

This category speeds up Power On Self Test (POST) after you power on the computer. If this is set to Enabled. BIOS will shorten or skip some check items during POST.

Enabled

(default) Enable quick POST

Disabled

Normal POST

First/Second/Third/ Boot Device, Boot Other Device

The BIOS attempts to load the operating system from the devices in the sequence selected in these items. The settings are Floppy, LS/ZIP, HDD-0/HDD-1/HDD-3, SCSI, CDROM, LAN and Disabled.

Swap Floppy Drive

Switches the floppy disk drives between being designated as A and B. Default is Disabled.

Boot Up Floppy Seek

During POST, BIOS will determine if the floppy disk drive installed is 40 or 80 tracks. 360K type is 40 tracks while 760K, 1.2M and 1.44M are all 80 tracks.

Boot Up NumLock Status

The default value is On.

(default)

Keypad is numeric keys.

Off

Keypad is arrow keys.

Gate A20 Option

Normal

The A20 signal is controlled by keyboard controller or chipset hardware.

Fast

(default) The A20 signal is controlled by port 92 or chipset specific method.

Typematic Rate Setting

Keystrokes repeat at a rate determined by the keyboard controller. When enabled, the typematic rate and typematic delay can be selected. The settings are: Enabled/Disabled.

Typematic Rate (Chars/Sec)

Sets the number of times a second to repeat a keystroke when you hold the key down. The settings are: 6, 8, 10, 12, 15, 20, 24, and 30.

Typematic Delay (Msec)

Sets the delay time after the key is held down before is begins to repeat the keystroke. The settings are 250, 500, 750, and 1000.

Security Option

This category allows you to limit access to the system and Setup, or just to Setup.

System

The system will not boot and access to Setup will be denied if the correct password is not entered at the prompt.

Setup

(default) The system will boot, but access to Setup will be denied if the correct

password is not entered prompt.

OS Select For DRAM > 64MB

Allows OS2 to be used with >64MB or DRAM. Settings are Non-OS/2 (default) and OS2. Set to OS/2 if using more than 64MB and running OS/2.

Report No FDD For Win 95

Whether report no FDD for Win 95 or not. The settings are: Yes, No.

3-6 Advanced Chipset Features

The Advanced Chipset Features Setup option is used to change the values of the chipset registers. These registers control most of the system options in the computer.

Advanced Chipset Features

Item Help

> DRAM Timing Settings Press Enter > AGP Function Settings Press Enter Prefetch Caching Disabled Memory Hole at 15M-16M Disabled

Menu Level >

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

DRAM Timing Settings

Please refer to section 3-6-1

AGP Function Settings

This option determines the effective size of the graphics aperture used in the particular PAC configuration. The AGP aperture is memory-mapped, while graphics data structure can reside in a graphics aperture. The aperture range should be programmed as not cacheable in the processor cache, accesses with the aperture range are forwarded to the main memory, then PAC will translate the original issued address via a translation table that is maintained on the main memory. The option allows the selection of an aperture size of 32MB, 64MB. Please refer to section 3-6-2

Memory Hole at 15M-16M

You can reserve this area of system memory for ISA adapter ROM. When this area is reserved, it cannot be cached. The user information of peripherals that need to use this area of system memory usually discusses their memory requirements. The settings are: Enabled and Disabled.

3-6-1 DRAM Timing Setting

DRAM Timing Setting

Item Help

Auto Configuration Standard RAS Active Time 7T RAS Precharge Time 2T RAS to CAS Delay 2T Write Recovery Time 2T CAS Latency Setting 2.5T

Menu Level >>

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

RAS Active Time

Select the number of SCLKs for an access cycle. The settings are: Auto (Default), 6T, 7T, 5T, 4T.

RAS Precharge Time

If an insufficient number of cycles is allowed for the RAS to accumulate its charge before DRAM refresh, the refresh may be incomplete and the DRAM may fail to retain date. Fast gives faster performance; and Slow gives more stable performance. This field applies only when synchronous DRAM is installed in the system. The settings are: 7T, 6T and 5T.

RAS to CAS Delay

This field let’s you insert a timing delay between the CAS and RAS strobe signals, used when DRAM is written to, read from, or refreshed. Fast gives faster performance; and Slow gives more stable performance. This field applies only when synchronous DRAM is installed in the system. The settings are: 2T and 3T.

CAS Latency Setting

When synchronous DRAM is installed, the number of clock cycles of CAS latency depends on the DRAM timing. The settings are: Auto (Default) 2T and 3T.

3-6-2 AGP Function Settings

AGP Function Settings

Item Help

AGP Transfer Mode Auto AGP Fast Write Disabled AGP Aperture Size 64MB AGP Aperture Write Combining Enabled AGP Driving Control Auto AGP Driving Value 88 System Share Memory Size 16MB

Menu Level >>

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

3-7 Integrated Peripherals

Integrated Peripherals

Item Help

> OnChip IDE Function Press Enter > OnChip Device Function Press Enter > Onboard SuperIO Function Press Enter Power Loss Function Always Off Init Display First PCI Slot

Menu Level >

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

OnChip IDE Function

Please refer to section 3-7-1

OnChip Device Function

Please refer to section 3-7-2

Onboard SuperIO Function

Please refer to section 3-7-3

Init Display First

This item allows you to decide to activate whether PCI Slot or AGP VGA first. The settings are: PCI Slot, AGP Slot.

3-7-1 OnChip IDE Function

OnChip IDE Function

Item Help

Internal PCI/IDE Both Primary Master PIO Auto Primary Slave PIO Auto Secondary Master PIO Auto Secondary Slave PIO Auto Primary Master UltraDMA Auto Primary Slave UltraDMA Auto Secondary Master UltraDMA Auto Secondary Slave UltraDMA Auto IDE Burst Mode Enabled IDE HDD Block Mode Enabled Delay For HDD (Secs) 0

Menu Level >>

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

Internal PCI/IDE

The integrated peripheral controller contains an IDE interface with support for two IDE channels. Select Both to activate each channel separately. The settings are: Both, IDE0, IDE1.

Primary/Secondary Master/Slave PIO

The four IDE PIO (Programmed Input/Output) fields let you set a PIO mode (0-4) for each of the four IDE devices that the onboard IDE interface supports. Modes 0 through 4 provide successively increased performance. In Auto mode, the system automatically determines the best mode for each device. The settings are: Auto, Mode 0, Mode 1, Mode 2, Mode 3, Mode

Primary/Secondary Master/Slave UltraDMA

Ultra DMA/33 implementation is possible only if your IDE hard drive supports it and the operating environment includes a DMA driver (Windows 95 OSR2 or a third-party IDE bus master driver). If your hard drive and your system software both support Ultra DMA/33 and Ultra DMA/66, select Auto to enable BIOS support. The settings are: Auto, Disabled.

IDE HDD Block Mode

Block mode is also called block transfer, multiple commands, or multiple sector read/write. If your IDE hard drive supports block mode (most new drives do), select Enabled for automatic

detection of the optimal number of block read/writes per sector the drive can support. The settings are: Enabled, Disabled.

3-7-2 OnChip Device Function

OnChip Device Function

Item Help

AC97 Audio Device Enabled Game Port Address 201 Midi Port Address Disabled Midi Port IRQ 10 AC97 Modem Device Enabled ETHERNET Function Enabled ETHERNET Address IDE Input Press Enter Current ETHERNET Address is 003018-XXXXXX USB Controller Enabled USB Keyboard Legacy Support Disabled

Menu Level >>

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

AC97 Sound Device

This item allows you to decide to enable/disable the chipset family to support AC97 Audio. The settings are: Enabled, Disabled.

Game Port Address/Midi Port Address

This will determine which Address the Game Port/Midi Port will use.

AC97 Modem Device

This item allows you to decide to enable/disable the chipset family to support AC97 Modem. The settings are: Auto, Disabled.

USB Controller

Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have a USB peripherals. The settings are: Enabled, Disabled.

USB Keyboard Legacy Support

Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have a USB keyboard. The settings are: Enabled, Disabled.

ETHERNET Address ID Input (Only for S450L)

This item allows you to setting the Mac address from 000000 to FFFFFF.

3-7-3 Onboard SuperIO Function

Onboard SuperIO Function

←

(Only for S450L)

Item Help

Onboard FDD Controller Enabled Onboard Serial Port 1 3F8/IRQ4 Onboard Serial Port 2 2F8/IRQ3 UART2 Mode Normal IR Duplex Mode Half Onboard Parallel Port 378/IRQ7 Parallel Port Mode SPP ECP Mode Use DMA 3

Menu Level >>

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

Onboard FDD Controller

Select Enabled if your system has a floppy disk controller (FDD) installed on the system board and you wish to use it. If you install add-on FDC or the system has no floppy drive, select Disabled in this field. The settings are: Enabled and Disabled.

Onboard Serial Port 1/Port 2

Select an address and corresponding interrupt for the first and the second serial ports. The settings are: 3F8/IRQ4, 2E8/IRQ3, 3E8/IRQ4, 2F8/IRQ3, Disabled, Auto.

UART 2 Mode

This item allows you to determine which InfraRed(IR) function of the onboard I/O chip, this functions uses.

Onboard Parallel Port

There is a built-in parallel port on the on-board Super I/O chipset that Provides Standard, ECP, and EPP features. It has the following option:

Disabled (3BCH/IRQ7)/

Line Printer port 0

(278H/IRQ5)/

Line Printer port 2

(378H/IRQ7)

Line Printer port 1

Parallel Port Mode

SPP : Standard Parallel Port EPP : Enhanced Parallel Port ECP : Extended Capability Port

SPP/EPP/ECP/ECP+EPP

To operate the onboard parallel port as Standard Parallel Port only, choose “SPP.” To operate the onboard parallel port in the EPP modes simultaneously, choose “EPP.” By choosing “ECP”, the onboard parallel port will operate in ECP mode only. Choosing “ECP+EPP” will allow the onboard parallel port to support both the ECP and EPP modes simultaneously. The ECP mode has to use the DMA channel, so choose the onboard parallel port with the ECP feature. After selecting it, the following message will appear: “ECP Mode Use DMA” at this time, the user can choose between DMA channels 3 to 1. The onboard parallel port is EPP Spec. compliant, so after the user chooses the onboard parallel port with the EPP function, the following message will be displayed on the screen: “EPP Mode Select.” At this time either EPP 1.7 spec. or EPP 1.9 spec. can be chosen.

3-8 Power Management Setup

The Power Management Setup allows you to configure your system to most effectively save energy saving while operating in a manner consistent with your own style of computer use.

Power Management Setup

Item Help

ACPI Function Enabled Video Off Option Always Off Video Off Method V/H SYNC+Blank MODEM Use IRQ Auto Hot key Function as Power Off Power Button Function Instant Off > PM Wake Up Events Press Enter

Menu Level >

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

ACPI Function

This item allows you to Enabled/Disabled the Advanced Configuration and Powe r Ma nag emen t (ACPI). The settings are Enabled and Disabled.

Video Off Option

This determines the manner in which the monitor is blanked. The choice are Suspend → off, All Modes → Off, and Always On.

Video Off Method

This determines the manner in which the monitor is blanked.

DPMS

(default) Initial display power management signaling.

Blank Screen

This option only writes blanks to the video buffer.

V/H SYNC+Blank

This selection will cause the system to turn off the vertical and

horizontal synchronization ports and write blanks to the video buffer.

Modem Use IRQ

This determines the IRQ in which the MODEM can use. The settings are: 3, 4, 5, 7, 9, 10, 11, NA.

Power Button Function

Pressing the power button for more than 4 seconds forces the system to enter the Soft-Off state. The settings are: Delay 4 Sec, Instant-Off.

PM Wake Up Events

Please refer to section 3-8-1

3-8-1 PM Wake Up Events

PM Wake Up Events

Item Help

IRQ [3-7,9-15],NMI Enabled IRQ 8 Break Suspend Disabled RING Power Up Control Disabled MACPME Power UP Control Disabled KB Power ON Password Enter Power Up by Alarm Disabled x Month Alarm NA x Day of Month Alarm NA x Time (hh:mm:ss) Alarm 0 : 0 : 0

Menu Level >>

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

Ring Power Up Control

During Disabled, the system will ignore any incoming call from the modem. During Enabled, the system will boot up if there’s an incoming call from the modem.

PCIPME Power Up Control

This will enable the system to wake up by PCI device Power Management function. The settings are: Enabled and Disabled.

KB Power ON Password

This item can setting Power On Password, if you Enabled keyboard Power On function then you can Power On system by key-in the password which you setting.

Power Up by Alarm

This function is for setting date and time for your computer to boot up. During Disabled, you cannot use this function. During Enabled, choose the Date and Time Alarm:

Date(of month) Alarm

You can choose which month the system will boot up. Set to 0, to boot every day.

Time(hh:mm:ss) Alarm

You can choose what hour, minute and second the system will boot up. Note: If you have change the setting, you must let the system boot up until it goes to the

operating system, before this function will work.

3-9 PnP/PCI Configuration Setup

This section describes configuring the PCI bus system. PCI, or Personal Computer Interconnect, is a system which allows I/O devices to operate at speeds nearing the speed the

CPU itself uses when communicating with its own special components. This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings.

PnP/PCI Configurations

Item Help

Reset Configuration Data Disabled

Resources Controlled By Manual > IRQ Resources Press Enter

PCI/VGA Palette Snoop Disabled Assign IRQ For VGA Enabled Assign IRQ For USB Enabled

Menu Level >

Default is Disabled. Select Enabled to reset Extended System Configuration Data (ESCD) when you exit Setup if you have installed a new add-on and the system reconfiguration has caused such a serious conflict that the OS cannot boot

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

Reset Configuration Data

No rma ll y, you leave this field Disabled. Select Enabled to reset Extended Sys tem Co nfi gur atio n Data (ESCD) when you exit Setup if you have installed a new add-on and the system reconfiguration has caused such a serious conflict that the operating system can not boot. The settings are: Enabled and Disabled.

Resource Controlled By

The Award Plug and Play BIOS has the capacity to automatically configure all of the boot and Plug and Play compatible devices. However, this capability means absolutely nothing unless you are using a Plug and Play operating system such as Windows



95/98. If you set this field to “manual” choose specific resources by going into each of the sub menu that follows this field (a sub menu is preceded by a “>”).

The settings are: Auto(ESCD), Manual.

IRQ Resources

When resources are controlled manually, assign each system interrupt a type, depending on the type of device using the interrupt. Please refer to section 3-9-1

PCI/VGA Palette Snoop

Leave this field at Disabled. The settings are Enabled, Disabled.

3-9-1 IRQ Resources

IRQ Resources

Item Help

IRQ-3 assigned to PCI Device IRQ-4 assigned to PCI Device IRQ-5 assigned to PCI Device IRQ-7 assigned to PCI Device IRQ-9 assigned to PCI Device IRQ-10 assigned to PCI Device IRQ-11 assigned to PCI Device IRQ-14 assigned to PCI Device IRQ-15 assigned to PCI Device

Menu Level >>

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

3-10 PC Health Status

This section shows the Status of you CPU, Fan, Warning for overall system status. This is only available if there is Hardware Monitor onboard.

PC Health Status

Item Help

Shutdown Temperature Disabled Show PC Health in Post Enabled Vcore 1.5V Vcc1.8V 1.80V Vcc3 3.3V Vcc5 5.01V +12V 12.02V SB3V 3.31V

-12V -11.95V SB5V 5.02V Vbat 3.01V CPU Temperature 43°C/109°C System Temperature 33°C/91°C CPU Fan 5500 RPM System Fan 0 RPM

Menu Level >

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

Show PC Health in Post

During Enabled, it displays information list below. The choice is either Enabled or Disabled

Current CPU Temperature/Current System Temp/Current CPUFAN, SYSFAN Speed/ Vcore/ Vcc/3.3V/+5V/+12V/-12V/5VSB(V)

This will show the CPU/FAN/System voltage chart and FAN Speed.

3-11 Miscellaneous Control

This section is for setting CPU Frequency Control.

Miscellaneous Control

Item Help

CPU Clock Ratio 10 X Auto Detect DIMM/PCI Clock Enabled Spread Spectrum Disabled Clock Control By Software ** Current Host Clock is 100/33MHz ** HOST/PCI Clock at Next Boot is 100/33MHz ** Current DRAM Clock is 100 MHz ** DRAM Clock at Next Boot is 100MH (HOST CLK)

Menu Level >

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

Auto Detect DIMM/PCI Clock

This item allows you to enable/disable auto detect DIMM/PCI Clock. The settings are: Enabled, Disabled.

Clock Control

This item allows you to set the CPU Host Clock by Hardware (CPU/PCI 100/33MHz) or by Software (BIOS)

Host/PCI clock at Next boot is

When Clock Control setting By Software this item allows you to set CPU Host Clock step by step from 100MHz to 200MHz, use Page Down/Page Up key can change the frequency to approach over clocking.

DRAM Clock at Next Boot is

This item allows you to set the DRAM clock synchronous as CPU Host Clock or Asynchronous as Host clock 100MHz, 133MHz, 166MHz to approach your DDR SDRAM specification.

3-12 Load Standard/Optimized Defaults

Load Standard Defaults

When you press <Enter> on this item, you get confirmation dialog box with a message similar to:

Load Standard Defaults (Y/N)? N Pressing <Y> loads the BIOS default values for the most stable, minimal-performance system operations.

Load Optimized Defaults

When you press <Enter> on this item, you get a confirmation dialog box with a message similar to:

Load Optimized Defaults (Y/N)? N Pressing <Y> loads the default values that are factory settings for optimal performance system operations.

3-13 Set Supervisor/User Password

You can set either supervisor or user password, or both of them. The differences are:

Supervisor password: Can enter and change the options of the setup menus. User password: Can only enter but do not have the right to change the options of the

setup menus. When you select this function, the following message will appear at the center of the screen to assist you in creating a password.

ENTER PASSWORD:

Type the password, up to eight characters in length, and press <Enter>. The password typed now will clear any previously entered password from CMOS memory. You will be asked to confirm the password. Type the password again and press <Enter>. You may also press <Esc> to abort the selection and not enter a password.

To disable a password, just press <Enter> when you are prompted to enter the password. A message will confirm that the password will be disabled. Once the password is disabled, the system will boot and you can enter Setup freely.

PASSWORD DISABLED.

When a password has been enabled, you will be prompted to enter it every time you try to enter Setup. This prevents an unauthorized person from changing any part of your system configuration.

Additionally, when a password is enabled, you can also require the BIOS to request a password every time your system is rebooted. This would prevent unauthorized use of your computer.

You determine when the password is required within the BIOS Features Setup Menu and its Security option. If the Security option is set to “System”, the password will be required both at boot and at entry to Setup. If set to “Setup”, prompting only occurs when trying to enter Setup.

Chapter 4

DRIVER & FREE PROGRAM INSTALLATION

Check your package and there is A MAGIC INSTALL CD included. This C D consists of all DRIVERS you need and some free application programs and utility programs. In addition, this CD also include an auto detect software which can tell you which hardware is installed, and which DRIVERS needed so that your system can function properly. We call this auto detect software MAGIC INSTALL.

MAGIC INSTALL Supports WINDOWS 95/98/98SE/ME/NT4.0/2000

Insert CD into your CD-ROM drive and the MAGIC INSTALL Menu should appear as below. If the menu does not appear, double-click MY COMPUTER / double-click CD-ROM drive or click START / click RUN / type X:\SETUP.EXE (assuming X is your CD-ROM drive).

From MAGIC INSTALL MENU you may make 11 selections:

1. AGPVXD install AGPVXD file when use External AGP card

2. VGA install SiS 650 On-chip VGA driver

3. SOUND install ALC201 Audio Codec driver

4. LAN install LAN controller driver (Only for S450L)

5. PC-HEALTH installs SMART GUARDIAN software for hardware monitoring device

6. MAGIC BIOS install BIOS Live Update Utility

7. PC-CILLIN install PC-CILLIN2000 anti-virus program

8. DIRECTX8 install Microsoft DirectX 8.0 driver

9. LANLED Install LAN State Utility

10. BROWSE CD to browse the contents of the CD

11. EXIT to exit from MAGIC INSTALL menu

4-1 AGPVXD Install SiS AGPVXD Driver

The AGPVXD Driver is Only For AGP Slot VGA CARD User, before install AGP card driver please install this AGPVXD driver first.

The path of the file:

for WINDOWS 9X is X:\SIS650\AGPVXD\WIN9X\SETUP.EXE (including WIN95/98/98SE/ME) for WINDOWS 2000/XP is X:\SIS650\AGPVXD\WIN2K_XP\SETUP.EXE

For WINDOWS 95/98/98SE/ME/2000/XP

1. Click AGPVXD when Magic Install

MENU appears

2. Click Next when SiS Aceleration Graphic

Port appears

3. Click NEXT or choose BROWSE to

change the path For the file to be stored

4. After Setup complete please select restart

my computer now and click Finish to complete setup

4-2 VGA Install SiS 650 VGA Driver

The path of the file: for WINDOWS 9X is X:\SIS650\VGA\WIN9X\SETUP.EXE (including Windows

98/98SE/ME)

for WINDOWS NT4.0 is X:\SIS650\VGA\WINNT40 for WINDOWS 2000 is X:\SIS650\VGA\WIN2000\SETUP.EXE for LINUX is X:\SIS650\LINUX

A. For WINDOWS 98/98SE/ME/2000

1. Click VGA when Magic Install MENU

appears

2. Click Next when SiS650 Multimedia

Package appears

3. Multimedia Package support three types

of Setup: Typical, Compact, Custom Please choice Typical and Click Next to continue step

4. System will add program icons to the

Program Folder listed. Click Next to continue, and after “Start Copying Files” window appears click Next

5. System starting install VGA driver 6. After Setup complete please select restart

my computer now and click Finish to complete setup

4-3 SOUND Install ALC201 Audio Codec Driver

1. Click SOUND when MAGIC INSTALL

MENU appears

2. Then auto detect operation system

language edition, click Next, start to install DRIVER

3. Click Finish and Restart Windows

4. Click Start→Program→Avance Sound Manager→AvRack. Then AVRACK Windows appears

5. Avance Audio Rack table can play CD, WAV, MID, MP3, AVI, MPG Format File

6. This is a Sound Environment Simulator and Karaok function table

NOTE: MAGIC INSTALL will auto detect file path:

X:\SIS650\SOUND\SETUP.EXE (for WINDOWS 95/98/98SE/ME/NT4.0/2000/XP)

4-4 LAN install LAN controller driver (Only for S450L)

The path of the file: for WINDOWS 9X/2000 is X:\SIS650\LANDRV\SETUP.EXE (I n c l u di n g WINDOWS 95/98/98SE/98ME/2000) for WINDOWS NT4.0 is X:\SIS650\LANDRV\NT40

WINDOWS 95/98/98SE/98ME/2000 Setup

1. Click LAN when Magic Install Menu appears 2. Click NEXT when SiS PCI LAN Driver Setup

appears

3. Choice restart my computer now to finish

setting up LAN Card, click Finish to complete setup

4. After restart computer you can check in

control Panel\System Device Manager\ Network adapters to make sure LAN card Driver setup completely Click NEXT when SiS PCI LAN Driver Setup appears

4-5 PC-HEALTH installs SMART GUARDIAN software for

hardware monitoring device

1. Click PC-HEALTH when MAGIC INSTALL

MENU appears

2. Click Install when SMART GUARDIAN

INSTALL appears

3. Click OK after the software is installed 4. SMART GUARDIAN Utility

NOTE: MAGIC INSTALL will auto detect file path X:\SIS650\HEALTH\SETUP.EXE This driver supports WINDOWS 95/98/98SE/NT4.0/2000

4-6 MAGIC BIOS Install BIOS Live Update Utility

1. Click Magic BIOS when Magic Install

MENU appears

2. Click Next to install the Magic BIOS in

Destination Folder

3. After finish Setup you will have a Magic

BIOS icon in your screen

4. Double click the Magic BIOS icon you

will have this picture, choose from internet you can upgrade BIOS On-line

5. When On-line update BIOS the program

will auto-check your BIOS version

6. Click Next if you need update BIOS,

after upgrade BIOS, the system will clear CMOS and automatically restart

7. Click Yes if you want to update the BIOS

otherwise choose No to exit

8. When System programming BIOS don’t turn

off power, after finish update BIOS, the system will clear CMOS and automatically Restart

9. When choose From Local Driver to update

BIOS, you must have the correct BIOS file in your Local Driver

10. Choose the correct BIOS file to update BIOS

4-7 PC-CILLIN Install PC-CILLIN 2000 Anti-virus program

1. Click PC-CILLIN when MAGIC INSTALL

MENU Appears

2. Click NEXT when PC-CILIN 2000 SETUP

APPEARS. Then click YES when the announcement of copywrite appears. Software is starting to detect HD for virus

3. Click NEXT and Enter User Information,

Click NEXT or choose BROWSE to change the path For the file to be stored

4. Click NEXT and Choose all Internet

Protection

5. Click OK and If You Have Proxy Server,

Enter Your Setting

6. Click NEXT when Start Copy Files, Start to

install the software

7. If you want to make a rescue disc, insert a

1.44 MB disc

8. Setup Complete and click Finish

9. Enter Your name and E-mail address

10. After install PC-cillin 2000 complete we

recommend select update item to download newest virus code and setting Auto refresh virus code

4-8 HOW TO DISABLE ON-BOARD SOUND.

Enter BIOS SETUP choose INTEGRATE PERIPHERALS choose ON-CHIP DEVICE FUNCTION choose AC97 SOUND DEVICE Disable on-board sound function by press PAGE DOWN KEY to Disable

4-9 HOW TO UPDATE BIOS

Method 1. Use “Magic BIOS” update BIOS in Windows 98 (refer page 42) Method 2. In DOS Mode

STEP 1. Prepare a boot disc. (you may make one by click START click RUN type SYS A:

click OK)

STEP 2. Copy utility program to your boot disc. You may copy from DRIVER CD

X:\FLASH\AWDFLASH.EXE or download from our web site.

STEP 3. Copy latest BIOS for S450/S450L from our web site to your boot disc. STEP 4. Insert your boot disc into A:,

start the computer, type “Awdflash A:\S450Axxx.BIN /SN/PY/CC/R” S450Axxx.BIN is the file name of latest BIOS it can be S450A03.BIN or

S450B02.BIN SN means don’t save existing BIOS data

PY means renew existing BIOS data CC means clear existing CMOS data R means restart computer

STEP 5. Push ENTER and the BIOS will be updated, computer will be restarted

automatically

JETWAY S450, S450L User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual