Jetway P4XFCR2A User Manual
P4XFCU/ P4XFCP/ P4XFCZ
USER'S MANUAL
M/B For Socket 478 Pentium 4 Processor
Trademark:
NO. G03-P4XFCR2A
Release date: December 2002
* Specifications and Information contained in this documentation are furnished for information use only, and are
subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
USER’S NOTICE............................................................................................................ii
MANUAL REVISION INFORMATION..........................................................................1
COOLING SOLUTIONS...............................................................................................1
CHAPTER 1 INTRODUCTION OF P4XFCU/P4XFCP/P4XFCZ MOTHERBOARD
1-1 FEATURE OF MOTHERBOARD........................................................2
1-2 SPECIFICATION.............................................................................3
1-3 PERFORMANCE LIST .....................................................................4
1-4 LAYOUT DIAGRAM & JUMPER SETTING.........................................5
CHAPTER 2 HARDWARE INSTALLATION
2-1 HARDWARE INSTALLATION STEPS ................................................7
2-2 CHECKING MOTHERBOARD'S JUMPER SETTING ............................7
2-3 INSTALL CPU ................................................................................8
2-3-1 GLOSSARY...........................................................................8
2-3-2 ABOUT INTEL PENTIUM 4 478-PIN CPU...................................9
2-4 INSTALL MEMORY ........................................................................9
2-5 EXPANSION CARD .........................................................................10
2-5-1 PROCEDURE FOR EXPANSION CARD INSTALLATION .............10
2-5-2 ASSIGNING IRQ FOR EXPANSION CARD.................................11
2-5-3 INTERRUPT REQUEST TABLE FOR THIS MOTHERBOARD.......11
2-5-4 AGP SLOT ............................................................................11
2-6 CONNECTORS, HEADERS...............................................................12
2-6-1 CONNECTORS ......................................................................12
2-6-2 HEADERS.............................................................................15
2-7 STARTING UP YOUR COMPUTER....................................................18
CHAPTER 3 INTRODUCING BIOS
3-1 ENTERING SETUP..........................................................................19
3-2 GETTING HELP .............................................................................19
3-3 THE MAIN MENU...........................................................................20
3-4 STANDARD CMOS FEATURES.........................................................21
3-5 ADVANCED BIOS FEATURES ..........................................................22
3-6 ADVANCED CHIPSET FEATURES ....................................................24
3-6-1 DRAM TIMING SETTINGS .....................................................25
3-6-2 AGP FUNCTION SETTINGS....................................................26
3-6-3 PCI TIMING SETTINGS .........................................................26
3-7 INTEGRATED PERIPHERALS ..........................................................26
3-7-1 ONCHIP IDE FUNCTION........................................................27
3-7-2 ONCHIP DEVICE FUNCTION..................................................28
3-7-3 ONCHIP SUPER IO FUNCTION...............................................29
3-8 POWER MANAGEMENT SETUP .......................................................30
3-8-1 PM WAKE UP EVENTS..........................................................31
3-8-1.1 IRQS ACTIVITIES...............................................................31
3-9 PNP/PCI CONFIGURATION SETUP...................................................32
3-9-1 IRQ RESOURCES..................................................................33
3-10 PC HEALTH STATUS .....................................................................33
3-11 MISCELLANEOUS CONTROL .........................................................34
3-12 LOAD STANDARD/OPTIMIZED DEFAULTS......................................35
3-13 SET SUPERVISOR/USER PASSWORD...............................................35
CHAPTER 4 DRIVER & FREE PROGRAM INSTALLATION
MAGIC INSTALL SUPPORTS WINDOWS 9X/ME/NT4.0/2000/XP...................36
4-1 VIA 4 IN 1
4-2 SOUND
4-3 LAN
4-4 PC-HEALTH
4-5 MAGIC BIOS
4-6 USB2.0
4-7 PC-CILLIN
4-8 HOW TO DISABLE ON-BOARD SOUND.............................................46
4-9 HOW TO UPDATE BIOS ..................................................................46
TABLE OF CONTENT
INSTALL VIA SERVICE PACK 4 IN 1 DRIVER
INSTALL CMI AUDIO CODEC DRIVER
INSTALL VIA 10/100MB LAN CONTROLLER DRIVER
WINBOND HARDWARE DOCTOR MONITORING SOFTWARE
INSTALL BIOS LIVE UPDATE UTILITY
INSTALL USB2.0 DRIVER
INSTALL PC-CILLIN2002 ANTI-VIRUS PROGRAM
.............................................44
.....................37
.............................39
.............................42
..........40
41
..............45
i
USER’S NOTICE
COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS
MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE
REPRODUCED, TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR
BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER.
THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE P4XFCU/P4XFCP/P4XFCZ
MOTHER-BOARD AND WE DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT
WIL L CHANGE, CORRECT ANY TIME WITHOUT NOTICE. MANUFACTURER PROVIDES THIS
MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, AND WILL NOT BE LIABLE FOR ANY
INDIRECT, SPECIAL, INCIDENTIAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMANGES FOR
LOSS OF PROFIT, LOSS OF BUSINESS, LOSS OF USE OF DATA, INTERRUPTION OF BUSINESS
AND THE LIKE).
PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE
REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES, AND
THEY ARE USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER’S
BENEFIT, WITHOUT INTENT TO INFRINGE.
Manual Revision Information
Reversion Revision History Date
2.0 Second Edition December 2002
Item Checklist
5
P4XFCU/P4XFCP/P4XFCZ motherboard
5
Cable for IDE/Floppy
5
CD for motherboard utilities
□
Cable for USB Port 3/4(Option)
5
P4XFCU/P4XFCP/P4XFCZ User’s Manual
Intel Pentium 4 Processor Family
Cooling Solutions
As processor technology pushes to faster speeds and higher performance, thermal management
becomes increasingly crucial when building computer systems. Maintaining the proper thermal
environment is key to reliable, long-term system operation. The overall goal in providing the proper
thermal environment is keeping the processor below its specified maximum case temperature.
Heatsinks induce improved processor heat dissipation through increased surface area and
concentrated airflow from attached fans. In addition, interface materials allow effective transfers of
heat from the processor to the heatsink. For optimum heat transfer, Intel recommends the use of
thermal grease and mounting clips to attach the heatsink to the processor.
When selecting a thermal solution for your system, please refer to the website below for collection
of heatsinks evaluated and recommended by Intel for use with Intel processors. Note, those heatsinks
are recommended for maintaining the specified Maximum T case requirement. In addition, this
collection is not intended to be a comprehensive listing of all heatsinks that support Intel processors.
For vendor list of heatsink and fan, please visit :
http://developer.intel.com/design/Pentium4/components/index
Chapter 1
1
Introduction of P4XFCU/P4XFCP/P4XFCZ Motherboard
1-1 Feature of motherboard
The P4XFCU/P4XFCP/P4XFCZ motherboard is design for use Intel Pentium 4 Processor
in 478 Pin Package Processor with the VIA P4X266E Chipset delivers a high pe rforman ce
and professional desktop platform solution. Which utilize the Socket 478 design and the
memory size expandable to 2.0GB.
These motherboards use the newest VIA P4X266E Chipset. Supports 533MHz System Bus
in data transfer rate. The motherboard provided 100MHz/133MHz Memory clock
frequency, support PC133/PC100 SDRAM and DDR266/DDR200 DDR Module. These
motherboards used VIA VT8235 V-Link LPC South Bridge offer ULTRA ATA 133 to
provide speedier HDD throughout that boosts overall system performance.
These motherboards also has an integrated AC’97 2.1 CODEC on board which is fully
compatible with Sound Blaster Pro that gives you the best sound quality and compatibility.
For those wanting even greater graphic performance, an AGP 4X slot is included on the
board, support AGP 2X/4X capability and Fast write Transaction.
With USB control as well as capability of expanding to 6x USB2.0 function ports delivering
480Mb/s bandwidth in these motherboards and rich connectivity, these motherboards meet
future USB demand also has built-in hardware monitor function to monitor and protect your
computer.
The P4XFCP/P4XFCZ motherboard including PCI LAN Controller chip support 10/100
Mb/sec Base transfer rate.
The P4XFCZ including the 1394 PCI controller provided 100M/200M/400Mb bandwidth
support two 1394 device port, which compliant with IEEE 1394A-2000 standard.
A useful software tool “Magic BIOS” examines the BIOS version automatically with the
correct version available on the web, links the site for users to download the latest version
of BIOS and updates the BIOS. Use “Magic BIOS”, users can download and update BIOS
automatically and completed under the OS easily.
These motherboards provide high performance & meets future specification demand. It is
really wise choice for your computer.
1-2 Specification
2
Spec Description
Design
Chipset
CPU Socket
(mPGA478B Socket)
Memory Socket
Expansion Slot &
Headers
Integrate IDE
1394 Port
(for P4XFCZ)
LAN On Board
(for P4XFCP/P4XFCZ)
USB2.0
Audio
BIOS
Multi I/O
ATX form factor 4 layers PCB size: 30.5x21.0cm
∗
VIA P4X266E North Bridge Chipset
∗
VIA VT8235 South Bridge Chipset
∗
Support Intel Pentium 4 478 Pin package utilizes Flip-Chip
∗
Pin Grid Array (FC-PGA2) package processor
Support 1.5G∼2.8G 478 Pin Pentium 4 processor
∗
Reserves support for future Intel Pentium 4 processors
∗
168-pin SDR SDRAM module socket x1 and 184-pin DDR
∗
Module socket x 2
Support 1 pcs PC133/PC100 SDRAM Module expandable to
∗
1.0GB, or 2 pcs DDR266/DDR200 DDR Modules Expandable
to 2.0GB
AGP slot x1 support AGP 2.0 & 4X mode
∗
32-bit PCI slot x5
∗
Two PCI IDE controllers support PCI Bus Mastering, ATA
∗
PIO/DMA and the ULTRA DMA 33/66/100/133 functions
that deliver the data transfer rate up to 133 MB/s
VIA VT6307 1394 Controller chip provided two 1394 device
∗
ports support 100/200/400Mb bandwidth
Compliant with IEEE 1394A-2000 standard
∗
VIA VT6103 LAN PHY chip
∗
Supports 10/100 Mb/sec data transfer rate
∗
VIA VT8235 South Bridge provided 6xUSB2.0 ports support
∗
480Mb/s bandwidth for USB2.0 devices
AC’97 Digital Audio controller integrated
∗
AC’97 Audio CODEC on board
∗
Audio driver and utility included
∗
Award 2MB Flash ROM
∗
PS/2 keyboard and PS/2 mouse connectors
∗
Floppy disk drive connector x1
∗
Parallel port x1, Serial port x2
∗
USB connector x2 for USB2.0
∗
USB headers x 4 (connecting cable option) for USB2.0
∗
Audio connector (Line-in, Line-out , MIC & Game Port)
∗
1-3 Performance List
3
The following performance data list is the testing result of some popular benchmark
testing programs. These data are just referred by users, and there is no responsibility
for different testing data values gotten by users (the different Hardware & Software
configuration will result in different benchmark testing results.)
Performance Test Report
CPU: Intel Pentium 4 1.9GHz mPGAB package
DRAM: 256MB DDR266 x1 (SAMSUNG K4H280838B-TCB0)
256MB SDRAM x1 (KINGMAX KSV684T4A1A-06)
VGA Expansion Card: NVDIA Geforce2 MX-400 64MB (1024x768xHi-color)
Hard Disk Driver: IBM DTLA-305040 (ATA-100)
BIOS: Award Optimal default
OS: Win 98SE
DDR266 PC133 SDRAM
3D Mark 2000 5432 5360
3D Mark 2001 2509 2479
3D Winbench 2000 104 102
Final Reality 9.99 9.06
Content Creation Winstone 2000 43.2 41.5
Content Creation Winstone 2001 50.3 49.5
Content Creation Winstone 2002 20.1 18.6
Business Winstone2001 44.1 42.8
Winbench 99:
CPU Mark 99 111 101
FPU Winmark 99 6610 6610
Business Disk Winmark99 7150 7090
Hi-end Disk Winmark99 18800 18500
Business Graphic Winmark 434 428
Hi-end Graphic Winmark 1260 1230
SYS Mark 2000/2001 : SISMark 2000/2001 Rating (Internet Content Creation /
Office Productivity)
SISMark 2000 208 (226/195) 200 (217/188)
SISMark 2001 150 (175/129) 142 (160/126)
SISOFT Sandra 2001 :
Dhrystone ALU MIPS 3626 3630
Whetstone FPU MFLOPS 1137/2371 1135/2368
Int ALU/RAM MB/S 1181 701
Float FPU/RAM MB/S 1183 701
Integer SSE2 IT/S 7547 7554
Floating-Point SSE2 IT/S 9352 9350
QUAKE3 DEMO1 FPS 169.1 146.7
DEMO2 FPS 169.7 146.1
WCPUID System/CPU Clock 101/1918.93 101/1918.93
1-4 Layout Diagram & Jumper Setting
4
(for P4XFCP/P4XFCZ)
LAN
PRINT GAME/MIDI PORT
PS/2 Mouse
PS/2
Keyboard
MIC
COM1 COM2 USB
LINE-IN
LINE-OUT
K/B Power ON Jumper (JP1)
PS2 KB/Mouse Port
USB/LAN Port
ATX 12V Power Conn.
ATX Power Conn.
CPU FAN
PC99 Back Panel
Front Panel Audio
ATX P9 Power Conn.
CD Audio
PCI Slot
VIA VT6103 Chip
1394 Port
(1394A, 1394B)
(for P4XFCZ)
USB Port
(USB1, USB2)
CPU Socket
SDR SDRAM DIMM x1
DDR SDRAM DIMM x2
VIA P4X266E Chip
System FAN
AGP Slot
VIA VT8235 Chip
Floppy Connector
ATA 133 IDE Conn.
Winbond W83697HF Chip
Clear CMOS (JBAT)
Front Panel Connector
IR Connector
Speaker Conn.
System FAN1
2MBit Flash ROM BIOS
Wake On LAN
Jumpers
Jumper Name Description Page
5
JBAT CMOS RAM Clear 3-pin Block P.7
JP1 Keyboard Power On Enable/Disabled 3-pin Block P.7
Connectors
Connector Name Description Page
ATXPWR ATX Power Connector 20-pin Block P.12
ATX12V ATX 12V Power Connector 4-pin Block P.12
ATXP9 ATX P9 Power Connector 6-pin Block P.13
PS2KBM PS/2 Mouse & PS/2 Keyboard
Connector
CN1/LAN USB2.0/LAN Port Connector 4-pin Connector
COM_LP Parallel Port Connector 25-pin Female P.13
AUDIO_GAME Audio/Game Connector 3 phone jack+15-pin Connector P.13
COM1/COM2 Serial Port COM1/2 Connector 9-pin Connector P.13
FDD Floppy Driver Connector 34-pin Block P.14
IDE1/IDE2 Primary/Secondary IDE Connector 40-pin Block P.14
6-pin Female P.13
P.13
RJ45 LAN Connector
Headers
Header Name Description Page
AUDIO SPEAKER, MIC header 9-pin Block P.15
USB1,USB2 USB2.0 Port Headers 9-pin Block P.15
1394A/1394B
(for P4XFCZ)
HD-LED IDE activity LED 2-pin Block P.15
RESET Reset switch lead 2-pin Block P.15
SPEAK PC Speaker connector 4-pin Block P.16
PWR-LED
PWR-BTN Power switch 2-pin Block P.16
WOL Wake On-LAN Headers 3-pin Block P.16
SFAN1, SYSFAN,CPUFAN FAN Headers 3-pin Block P.16
IR IR infrared module Headers 5-pin Block P.17
CD_IN CD Audio-In Headers 4-pin Block P.17
Expansion Sockets
Socket/Slot Name Description Page
ZIF Socket 478 Pin CPU Socket 478-pin mPGA CPU Socket P.9
SDR1 SDRAM Module
DDR1, DDR2 DDR Module Socket 184-pin DDR Module expansion Socket P.9
PCI1 ∼ PCI5
AGP AGP 4X Mode Slot AGP Expansion Slot P.11
1394 port headers 9-pin Block P.15
Power LED 2-pin Block P.16
168-pin SDR SDRAM Module
Socket
PCI Slot 32-bit PCI Local Bus Expansion slots P.10
Expansion Socket
P.9
Hardware installation
Chapter 2
6
2-1 Hardware installation Steps
Before using your computer, you had better complete the following steps:
1. Check motherboard jumper setting
2. Install CPU and Fan
3. Install System Memory (DIMM)
4. Install Expansion cards
5. Connect IDE and Floppy cables, Front Panel /Back Panel cable
6. Connect ATX Power cable
7. Power-On and Load Standard Default
8. Reboot
9. Install Operating System
10. Install Driver and Utility
2-2 Checking Motherboard’s Jumper Setting
(1) CMOS RAM Clear (3-pin) : JBAT
A battery must be used to retain the motherboard configuration in CMOS RAM short
1-2 pins of JBAT to store the CMOS data.
To clear the CMOS, follow the procedure below:
1. Turn off the system and unplug the AC power
2. Remove ATX power cable from ATX power connector
3. Locate JBAT and short pins 2-3 for a few seconds
4. Return JBAT to its normal setting by shorting pins 1-2
5. Connect ATX power cable back to ATX power connector
Note: When should clear CMOS
1. Troubleshooting
2. Forget password
3. After over clocking system boot fail
JBAT
13
1-2 closed Normal
CMOS RAM Clear Setting
JBAT
13
2-3 closed Clear CMOS
(2) Keyboard Power On function Enabled/Disabled: JP1
When setting Enabled you can using keyboard by key in password to power on system.
7
JP1
1
3
(Default)
JP1
1
3
2-3 closed K/B Power ON Enabled1-2 closed K/B Power ON Disable
Keyboard Power On Setting
2-3 Install CPU
2-3-1 Glossary
Chipset (or core logic) - two or more integrated circuits which control the interfaces
between the system processor, RAM, I/O devises, and adapter cards.
Processor slot/socket - the slot or socket used to mount the system processor on the
motherboard.
Slot (AGP, PCI, ISA, RAM) - the slots used to mount adapter cards and system RAM.
AGP - Accelerated Graphics Port - a high speed interface for video cards; runs at 1X
(66MHz), 2X (133MHz), or 4X (266MHz).
PCI - Peripheral Component Interconnect - a high speed in terface for video cards, sound
cards, network interface cards, and modems; runs at 33MHz.
ISA - Industry Standard Architecture - a relatively low speed interface primarily used for
sound cards and modems; runs at approx. 8MHz.
Serial Port - a low speed interface typically used for mouse and external modems.
Parallel Port - a low speed interface typically used for printers.
PS/2 - a low speed interface used for mouse and keyboards.
USB - Universal Serial Bus - a medium speed interface typically used for mouse, keyboards,
scanners, and some digital cameras.
Sound (interface) - the interface between the sound card or integrated sound connectors and
speakers, MIC, game controllers, and MIDI sound devices.
LAN (interface) - Local Area Network - the interface to your local area network.
BIOS (Basic Input/Output System) - the program logic used to boot up a computer and
establish the relationship between the various components.
Driver - software, which defines the characteristics of a device for use by another device or
other software.
Processor - the "central processing unit" (CPU); the principal integrated circuit used for
doing the "computing" in "personal computer"
Front Side Bus Frequency - the working frequency of the motherboard, which is generated
by the clock generator for CPU, DRAM and PCI BUS.
CPU L2 Cache - the flash memory inside the CPU, normal it depend on CPU type.
8
2-3-2 About Intel Pentium 4 478-pin CPU
This motherboard provides a 478-pin surface mount, Zero Insertion Force (ZIF) socket,
referred to as the mPGA478B socket supports Intel Pentium 4 processor in the 478 Pin
package utilizes Flip-Chip Pin Grid Array (FC-PGA2) package technology.
The CPU that comes with the motherboard should have a cooling FAN attached to prevent
overheating. If this is not the case, then purchase a correct cooling FAN before you turn on
your system.
WARNING! Be sure that there is sufficient air circulation across the processor’s
heatsink and CPU cooling FAN is working correctly, otherwise it may
cause the processor and motherboard overheat and damage, you may
install an auxiliary cooling FAN, if necessary.
To install a CPU, first turn off your system and remove its cover. Locate the ZIF socket
and open it by first pulling the level sideways away from the socket then upward to a 90degree angle. Insert the CPU with the correct orientation as shown below. The notched
corner should point toward the end of the level. Because the CPU has a corner pin for two
of the four corners, the CPU will only fit in the orientation as shown.
CPU ZIF mPGAB Socket
mPGA478B
Colden Arrow
When you put the CPU into the ZIF socket. No force require to insert of the CPU, then
press the level to Locate position slightly without any extra force.
2-4 Install Memory
This motherboard provides two 184-pin DDR DUAL INLINE MEMORY MODULES
(DIMM) sites for DDR memory expansion available from minimum memory size of 64MB
to maximum memory size of 2.0GB SDR SDRAM, or one 168-pin SDR DIMM sites for
SDRAM memory for maximum memory size of 1.0GB.
Valid Memory Configurations
Bank 184-pin DDR DIMM PCS Total Memory
Bank 0, 1 (DDR1) DDR266/DDR200 DDR DRAM Module X1 64MB∼1.0GB
Bank 2, 3 (DDR2) DDR266/DDR200 DDR DRAM Module X1 64MB∼1.0GB
Total System Memory (Max. 2.0GB) X2 64MB∼2.0GB
Bank 168-pin SDR DIMM PCS Total Memory
Bank 0, 1 (SDR1) PC133/PC100 SDR DRAM Module X1 64MB∼1.0GB
Total System Memory (Max. 1.0GB) X1 64MB∼1.0GB
9
Generally, installing SDR/DDR SDRAM modules to your motherboard is very easy, you
can refer to figure 2-4 to see what a 168-pin SDR/184-pin DDR SDRAM module looks
like.
DDR2 (BANK2+BANK3)
DDR1 (BANK0+BANK1)
SDR1 (BANK0+BANK1)
Figure 2-4
NOTE! When you install DIMM module fully into the DIMM socket the eject tab should
be locked into the DIMM module very firmly and fit into its indention on both
sides.
WARNING! For the SDR SDRAM CLOCK is set at 133MHz, use only PC133/DDR266-
compliant SDR/DDR Modules. When this motherboard operate at 133Mhz,
most system will not even boot if non-compliant modules are used because of the
strict timing issues, if your SDR/DDR Modules are not PC133/DDR266compliant, set the SDRAM clock to 100MHz to ensure system stability.
NOTE! It is only can install either SDRAM or DDR Module at one time. Don’t install
both DDR Module and SDR Module at same time, it will have risk to damage
your Memory and Motherboard.
2-5 Expansion Cards
WARNING! Turn off your power when adding or removing expansion cards or other
system components. Failure to do so may cause severe damage to both
your motherboard and expansion cards.
2-5-1 Procedure For Expansion Card Installation
1. Read the documentation for your expansion card and make any necessary hardware or
software setting for your expansion card such as jumpers.
2. Remove your computer’s cover and the bracket plate on the slot you intend to use.
3. Align the card’s connectors and press firmly.
4. Secure the card on the slot with the screen you remove above.
5. Replace the computer system’s cover.
6. Set up the BIOS if necessary.
7. Install the necessary software driver for your expansion card.
10
2-5-2 Assigning IRQs For Expansion Card
Some expansion cards need an IRQ to operate. Generally, an IRQ must exclusively assign
to one use. In a standard design, there are 16 IRQs available but most of them are already
in use.
Standard Interrupt Assignments
IRQ Priority Standard function
0 N/A System Timer
1 N/A Keyboard Controller
2 N/A Programmable Interrupt
3 * 8 Communications Port (COM2)
4 * 9 Communications Port (COM1)
5 * 6 Sound Card (sometimes LPT2)
6 * 11 Floppy Disk Controller
7 * 7 Printer Port (LPT1)
8 N/A System CMOS/Real Time Clock
9 * 10 ACPI Mode when enabled
10 * 3 IRQ Holder for PCI Steering
11 * 2 IRQ Holder for PCI Steering
12 * 4 PS/2 Compatible Mouse Port
13 N/A Numeric Data Processor
14 * 5 Primary IDE Channel
15 * 1 Secondary IDE Channel
* These IRQs are usually available for ISA or PCI devices.
2-5-3 Interrupt Request Table For This Motherboard
Interrupt request are shared as shown the table below:
INT A INT B INT C INT D INT E INT F INT G INT H
Slot 1
√
Slot 2
Slot 3
Slot4
Slot5
Onboard USB 1
Onboard USB 2
AC97/MC97
IMPORTANT! If using PCI cards on shared slots, make sure that the drivers support
“Shared IRQ” or that the cards don’t need IRQ assignments. Conflicts
will arise between the two PCI groups that will make the system
unstable or cards inoperable.
√
√
√
√
√
√
√
2-5-4 AGP Slot
This motherboard provides an AGP Slot, support the 2X/4X AGP VGA card.
11
2x notch 4x notch
AGP SLOT
2-6 Connectors, Headers
2-6-1 Connectors
(1) Power Connector (20-pin block) : ATXPWR
ATX Power Supply connector. This is a new defined 20-pins connector that usually
comes with ATX case. The ATX Power Supply allows to use soft power on momentary
switch that connect from the front panel switch to 2-pins Power On jumper pole on the
motherboard. When the power switch on the back of the ATX power supply turned on,
the full power will not come into the system board until the front panel switch is
momentarily pressed. Press this switch again will turn off the power to the system board.
Pin 1
PIN ROW2 ROW1
1 3.3V 3.3V
2 -12V 3.3V
3 GND GND
4 Soft Power On 5V
5 GND GND
6 GND 5V
7 GND GND
8 -5V Power OK
9 +5V +5V (for Soft Logic)
10 +5V +12V
(2) ATX 12V Power Connector (4-pin block) : ATX12V
This is a new defined 4-pins connector that usually comes with ATX Power Supply. The
ATX Power Supply which fully support Pentium 4 processor must including this
connector for support extra 12V voltage to maintain system power consumption. Without
this connector might cause system unstable because the power supply can not provide
sufficient current for system.
Pin 1
12
(3) ATX P6 Power Connector (6-pin block) : ATXP9
This is a new defined 6-pins connector that usually comes with ATX Power Supply.
The ATX Power Supply which fully support Pentium 4 processor must including this
connector for support extra 3.3V and 5V voltage to maintain system power
consumption. Without this connector might cause system unstable because the power
supply can not provide sufficient current for system.
5V
3.3V 3.3V
GND
GND GND
Power Plugs from Power Supply Power Connector on Motherboard
RED
ORG
ORG
BLK
BLK
BLK
(4) PS/2 Mouse & PS/2 Keyboard Connector: PS2KBM
The connectors for PS/2 keyboard and PS/2 Mouse.
(5) USB Port connector: CN1
The connectors are 4-pin connector that connect USB devices to the system board.
(6) LAN Port Connector : LAN (for P4XFCP/ P4XFCZ)
This connector is a standard RJ45 connector for Network connection.
(7) Parallel Port Connector (25-pin female): LPT
Parallel Port connector is a 25-pin D-Subminiature Receptacle connector. The On-board
Parallel Port can be disabled through the BIOS SETUP. Please refer to Chapter 3
“INTEGRATED PERIPHERALS SETUP” section for more detail information.
(8) Audio and Game Connector : AUDIO_GAME
This Connector are 3 phone Jack for LINE-OUT, LINE-IN, MIC and a 15-pin
D-Subminiature Receptacle Connector for joystick/MIDI Device.
Line-out : Audio output to speaker
Line-in : Audio input to sound chip
MIC : Microphone Connector
Game/MIDI : For joystick or MIDI Device
(9) Serial Port COM1, COM2 : COM1, COM2
COM1, COM2 are the 9-pin D-Subminiature mail connector. The On-board serial port can be
disabled through BIOS SETUP. Please refer to Chapter 3 “INTEGRATED PERIPHERALS
SETUP” sect i o n f o r m o r e detail information.
PS/2
Mouse
PS/2
Keyboard
LAN
USB
PRINT
COM1 COM2
GAME/MIDI PORT
MIC
LINE-IN
LINE-OUT
13
Loading...