JETWAY NAF95-Q87 User Manual

USER'S MANUAL

Of

Intel Q87 Express Chipset

Based

M/B for LGA 1150 Quad Core Ready

Intel Core Processor

No. G03-NAF95-F

Rev: 1.0

Release date: July 25, 2013

Trademark:

* Specifications and Information contained in this documentation a re furnis hed for i nforma tion use only , a nd are

subject to change at any time without notice, and should not be construed as a commitment by manufacturer.

ii

ENVIRONMENTAL SAFETY INSTRUCTION...........................................................................iii

ENVIRONMENTAL PROTECTION ANNOUCEMENT..............................................................iii

USER’S NOTICE .......................................................................................................................iv

MANUAL REVISION INFORMATION.......................................................................................iv

ITEM CHECKLIST.....................................................................................................................iv

CHAPTER 1 INTRODUCTION OF THE MOTHERBOARD

1-1 SPECIFICATION.........................................................................................................1

1-2 LAYOUT DIAGRAM....................................................................................................2

CHAPTER 2 HARDWARE INSTALLATION

2-1 JUMPER SETTING.....................................................................................................5

2-2 CONNECTORS AND HEADERS................................................................................10

2-2-1 REAR I/O BACK PANEL CONNECTORS....................................................10

2-2-2 MOTHERBOARD INTERNAL CONNECTORS............................................11

2-2-3 HEADER PIN DEFINITION ...........................................................................13

CHAPTER 3 INTRODUCING BIOS

3-1 ENTERNING SETUP...................................................................................................18

3-2 BIOS MENU SCREEN ................................................................................................18

3-3 FUNCTION KEYS .......................................................................................................19

3-4 GETTING HELP ..........................................................................................................19

3-5 MENU BARS...............................................................................................................20

3-6 MAIN MENU................................................................................................................20

3-7 ADVANCED MENU.....................................................................................................21

3-8 CHIPSET MENU..........................................................................................................28

3-9 BOOT MENU...............................................................................................................30

3-10 SECURITY MENU.......................................................................................................31

3-11 SAVE & EXIT MENU...................................................................................................32

TABLE OF CONTENT

iii

Environmental Safety Instruction

z Avoid the dusty, humidity and temperature extremes. Do not place the product in

any area where it may become wet.

z 0 to 40 centigrade is the suitable temperature. (The figure comes from the request

of the main chipset)

z Generally speaking, dramatic changes in temperature may lead to contact

malfunction and crackles due to constant thermal expansion and contraction from
the welding spots’ that connect components and PCB. Computer should go
through an adaptive phase before it boots when it is moved from a cold
environment to a warmer one to avoid condensation phenomenon. These water
drops attached on PCB or the surface of the components can bring about
phenomena as minor as computer instability resulted from corrosion and oxidation
from components and PCB or as major as short circuit that can burn the
components. Suggest starting the computer until the temperature goes up.

z The increasing temperature of the capacitor may decrease the life of computer.

Using the close case may decrease the life of other device because the higher
temperature in the inner of the case.

z Attention to the heat sink when you over-clocking. The higher temperature may

decrease the life of the device and burned the capacitor.

Environmental Protection Announcement

Do not dispose this electronic device into the trash while discarding. To minimize
pollution and ensure environment protection of mother earth, please recycle.

iv

USER’S NOTICE

COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL,
INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED, TRANSMITTED
OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN
PERMISSION OF THE MANUFACTURER.

THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE THIS MOTHER-BOARD SERI ES AND WE
DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT WILL CHANGE, CORRECT ANY TIME
WITHOUT NOTICE. MANUFACTURER PROVIDES THIS M ANUAL “AS IS” WITHOUT WARRANTY OF ANY
KIND, AND WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFIT, LOSS OF BUSINESS, LOSS OF USE OF DATA,
INTERRUPTION OF BUSINESS AND THE LIKE).

PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE
REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES, AND THEY ARE
USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER’S BENEFIT, WITHOUT
INTENT TO INFRINGE.

Manual Revision Information

Reversion Revision History Date

1.0 First Edition July 25, 2013

Item Checklist

5

Motherboard

5

User’s Manual

5

DVD for motherboard utilities

5

Cable(s)

5

I/O Back panel shield

1

Chapter 1

Introduction of the Motherboard

1-1 Specification

Spec Description

Design

z ATX form factor; PCB size: 30.5 x24.5 cm

Chipset

z Intel® Q87 Express Chipset

LGA1155
CPU Socket

z Supports Intel® Core™ i7, Core™ i5, Core™ i3 series, Pentium®

processor in LAG1150 Package

* for detailed CPU support information please visit our website

Memory Slot

z DDRIII RAM module slot x 4
z Supporting four DDRIII 1600/1333/1066MHz RAM Module

expandable to 32 GB (Maximum)

z Support dual-channel function

Expansion Slots

z 1 pcs* PCI-Express x16 slot (PE1)
z 1 pcs* PCI-Express x4 slot (PE2)
z 1 pcs* PCI-Express x1 slot (PE3)
z 4 pcs *32-bit PCI slot
z 1 pcs* Full-size Mini-PCIE slot (PE4)
z 1 pcs* Full-size MSATA slot

Storage

z 6 * SATAIII 6Gb/s ports support RAID 0, 1, 5, 10 function

Dual LAN Chips

z Integrated Intel® 82574L and i217-LM Gigabit Ethernet LAN chip

that supports Fast Ethernet LAN function of providing
10/100/1000Mbps Ethernet data transfer rate

HD Audio Chip

z Realtek ALC662 6-channel Audio Codec integrated
z Audio driver and utility included

BIOS

z 64M Bit DIP Flash ROM

Multi I/O

Rear Panel I/O:

z Serial port connector x1
z Display port connector x1
z HDMI port connector x1
z DVI-D port connector x1
z VGA port connector x1
z USB 3.0 port connector x2
z USB 2.0 port connector x4
z RJ-45 LAN connector x2
z Audio connector x3 (Line-in, Line-out, MIC)

Internal I/O Connectors& Headers:

z 1 *24-pin main power connector
z 1 *8-pin 12V Power connector
z Front panel audio header x1
z CDIN header x1
z HDMI-SPDIF header x1
z PS/2 KB & MS header x1
z GPIO header x1
z CIR header x1
z TPM 1.2 header x1
z USB 3.0 header x1 (support two expansion USB 3.0 ports)
z USB 2.0 header x2 (support four expansion USB 2.0 ports)
z Front panel header x1
z POWER LED1+Speaker header x1
z COM port header x 9
z SM_BUS header x1
z LANLED header x2
z Fan header x 3

2

1-2 Layout Diagram

Rear IO Diagram

Motherboard Internal Diagram

*Notice: 1.

PE4 slot functions as full-size Mini-PCIE slot and shares function with PE3, i.e. only
one can function at a time.2. MSATA slot shares function with SATA6 port; user can only choose
one to use at one time.

RJ-45 LAN Ports

USB 3.0 Ports

Line-IN/

Optical SPDIF OUT

Line-OUT

MIC-IN

USB 2.0 Ports

VGA Port

ATX 12V

Power Connector

ATX Powe

r

Connector

LGA 1150

CPU Socket

DVI-D PortHDMI Port

Serial Port

Audio Connectors

USB 3.0 Ports

over HDMI Port

VGA Port over

DVI–D Port

RJ-45 LAN Ports

Over USB 2.0 Ports

RJ-45 LAN Ports

Over USB 2.0 Ports

USB 3.0 Header

PCI Express x16 Slot (PE1)

PCI Express 2.0 x 4 Slot (PE2)

P

CI Express 2.0 x1 Slot

(

PE3)

32-bit PCI Slots

Front Panel

Audio Heade

r

CDIN Header

TPM Header

Intel Q87

Chipset

USB 2.0 Headers

Front Panel Header

DDRIII

DIMM Slot x 4

Full-size

Mini-PCIE Slot

(PE4) *

SYS FAN1 Heade

r

GPIO Header

SYS FAN2 Heade

r

KBMS Header

CPUFAN Header

SM_BUS Header

CIR Header

Serial Ports

(COM2/3/4/5/6/7/8/9/10)

SATAIII Ports

HDMI S/PDIF Header

PWR LED +Speaker

Header (JP15

)

Display Port

Serial Port over

Display Port

NICLED Headers

Full-size MSATA Slot (MSATA)

3

Motherboard Jumper Position

Jumper

Jumper Name Description

JP1 COM1 Port Pin9 Function Select 4-pin Block
JP9 COM2 Header Pin9 Function Select 4-pin Block
JP5 COM3 Header Pin9 Function Select 4-pin Block
JP6 COM5 Header Pin9 Function Select 4-pin Block
JP7 COM7 Header Pin9 Function Select 4-pin Block
JP8 COM9 Header Pin9 Function Select 4-pin Block
JP10 COM4 Header Pin9 Function Select 4-pin Block
JP11 COM6 Header Pin9 Function Select 4-pin Block
JP12 COM8 Header Pin9 Function Select 6-pin Block
JP13 COM10 Header Pin9 Function Select 6-pin Block
JP14 ME_Features Select 2-pin Block
JBAT CMOS RAM Clear Function Setting 3-pin Block
JP2 Mini PCI-E Slot (PE4)VCC3.3V/3.3VSB Select 3-pin Block
JP4 MSATA Slot (MSATA)VCC3.3V/3.3VSB Select 3-pin Block
Case_OPEN Case Open Message Display Function Select 2-pin Block

JP2

CASE_OPEN

J

P1

JBAT J

P12

JP5J

P11

J

P10

JP9JP6

JP14

JP7

JP

8

J

P13

4

Connectors

Connector Name

ATXPWR ATX Power Connector
ATX12V ATX 12V Power Connector
COM1 Serial Port COM Connector

DP Display Port
USB1 USB 3.0 Connector X2
HDMI High-Definition Multimedia Interface

CRT Video Graphic Attach Connector
DVI1 DVI-D Port Connector
UL1(Top)/UL2(Top) RJ-45 LAN Connector X2
UL1(Middle & Bottom)/UL2(Middle & Bottom) USB 2.0 Port Connector X4
AUDIO Line Out /Line In /MIC

Audio Connector

SATA1/2/3/4/5/6 SATAIII Connector X6

Headers

Header Name Description

FP_AUDIO Front Panel Audio Header 9-pin Block
CD_IN CD Audio-In Header 4-pin Block
HDMI_SPDIF HDMI_SPDIF Out Header 2-pin Block
KBMS PS/2 Keyboard & Mouse Header 6-pin Block
GPIO_CON GPIO Header 10-pin Block
CIR_CON CIR Header 7-pin Block
TPM TPM Header 19-pin Block
USB2 USB 3.0 Header 19-pin Block
USB3/USB4 USB 2.0 Header 9-pin Block
JW_FP
(Front Panel Header)

PWR LED/ HD LED/ /Power Button

/Reset

9-pin Block

JP15 Power LED+ Speaker Header 7-pin Block
COM 2/3/4/5/6/7/8/9/10 Serial Port Header 9-pin Block
SM_BUS SMBUS Header 4-pin Block
NIC_LED1/ NIC_LED2 LANLED Activity Header 2-pin Block
SYSFAN1/SYSFAN2/CPUFAN FAN Header 4-pin Block

5

Chapter 2

Hardware Installation

2-1 Jumper Setting

JP1 (4-pin): COM1 Port Pin9 Function Select

JP1→COM 1 Po rt

4-6 Closed:

RI= 12V ;

642

3-4 Closed:

RI= 5V;

2-4 Closed:

RI=RS232

3

1

5

13

5

24

6

1 3

5

2 4 6

JP9 (4-pin): COM2 Header Pin9 Function Select

JP9→ COM 2 He ade r

4-6 Closed:

RI= 12V ;

642

3-4 Closed:

RI= 5V;

2-4 Closed:

RI=RS232

3

1

5

13

5

24

6

1 3

5

2 4 6

JP5 (4-pin): COM3 Header Pin9 Function Select

JP5→ COM 3 He ade r

4-6 Closed:

RI= 12V ;

642

3-4 Closed:

RI= 5V;

2-4 Closed:

RI=RS232

3

1

5

13

5

24

6

1 3

5

2 4 6

6

JP6 (4-pin): COM5 Header Pin9 Function Select

JP6→COM5 Header

4-6 Closed:

RI= 12V ;

642

3-4 Closed:

RI= 5V;

2-4 Closed:

RI=RS232

3

1

5

13

5

24

6

1 3

5

2 4 6

JP7 (4-pin): COM7 Header Pin9 Function Select

JP7→COM7 Header

4-6 Closed:

RI= 12V ;

642

3-4 Closed:

RI= 5V;

2-4 Closed:

RI=RS232

3

1

5

13

5

24

6

1 3

5

2 4 6

JP8 (4-pin): COM9 Header Pin9 Function Select

JP8→COM9 Header

4-6 Closed:

RI= 12V ;

642

3-4 Closed:

RI= 5V;

2-4 Closed:

RI=RS232

3

1

5

13

5

24

6

1 3

5

2 4 6

7

JP10 (4-pin): COM4 Header Pin9 Function Select

JP10→ COM 4 He ade r

4-6 Closed:

RI= 12V ;

642

3-4 Closed:

RI= 5V;

2-4 Closed:

RI=RS232

3

1

5

13

5

24

6

1 3

5

2 4 6

JP11 (4-pin): COM6 Header Pin9 Function Select

JP11→ COM 6 He ade r

4-6 Closed:

RI= 12V ;

642

3-4 Closed:

RI= 5V;

2-4 Closed:

RI=RS232

3

1

5

13

5

24

6

1 3

5

2 4 6

JP12 (4-pin): COM8 Port Pin9 Function Select

JP12→ COM 8 He ade r

4-6 Closed:

RI= 12V ;

642

3-4 Closed:

RI= 5V;

2-4 Closed:

RI=RS232

3

1

5

13

5

24

6

1 3

5

2 4 6