JETWAY I407, I407L User Manual
I407 / I407L
USER'S MANUAL
M/B For Socket 478 Pentium 4 Processor
NO. G03-I407R1A
Release date: December 2001
Trademark:
* Specifications and Information contained in this documentation are furnished for information use only, and are
subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
i
USER’S NOTICE...........................................................................ii
MANUAL REVISION INFORMATION ...........................................1
COOLING SOLUTIONS................................................................1
CHAPTER 1 INTRODUCTION OF I407/I407L MOTHERBOARD
1-1 FEATURE OF MOTHERBOARD............................................................... 2
1-2 SPECIFICATION..........................................................................................3
1-3 PERFORMANCE LIST ................................................................................ 4
1-4 LAYOUT DIAGRAM & JUMPER SETTING...........................................5
CHAPTER 2 HARDWARE INSTALLATION
2-1 HARDWARE INSTALLATION STEPS.....................................................7
2-2 CHECKING MOTHERBOARD'S JUMPER SETTING ..........................7
2-3 INSTALL CPU ...............................................................................................8
2-3-1 GLOSSARY ...................................................................................................8
2-3-2
ABOUT INTEL PENTIUM 4 478-PIN CPU
........................................9
2-4 INSTALL MEMORY .................................................................................... 10
2-5 EXPANSION CARD......................................................................................11
2-5-1 PROCEDURE FOR EXPANSION CARD INSTALLATION..................11
2-5-2 ASSIGNING IRQ FOR EXPANSION CARD............................................
11
2-5-3 INTERRUPT REQUEST TABLE FOR THIS MOTHERBOARD..........
12
2-5-4 AGP SLOT.....................................................................................................
12
2-6 CONNECTORS, HEADERS ........................................................................13
2-6-1 CONNECTORS.............................................................................................
13
2-6-2 HEADERS......................................................................................................16
2-7 STARTING UP YOUR COMPUTER.......................................................... 20
CHAPTER 3 INTRODUCING BIOS
3-1 ENTERING SETUP.......................................................................................21
3-2 GETTING HELP............................................................................................22
3-3 THE MAIN MENU ........................................................................................22
3-4 STANDARD CMOS FEATURES.................................................................23
3-5 ADVANCED BIOS FEATURES ..................................................................25
3-6 ADVANCED CHIPSET FEATURES ..........................................................27
3-6-1 DRAM TIMING SETTINGS............................................................28
3-7 INTEGRATED PERIPHERALS..................................................................28
3-7-1 ONCHIP IDE FUNCTION................................................................29
3-7-2 ONCHIP DEVICE FUNCTION.......................................................30
3-7-3 ONCHIP SUPER IO FUNCTION.................................................... 31
3-8 POWER MANAGEMENT SETUP..............................................................32
3-8-1 PM TIMER RELOAD EVENTS......................................................34
3-9 PNP/PCI CONFIGURATION SETUP.........................................................34
3-9-1 IRQ RESOURCES ............................................................................ 35
TABLE OF CONTENT
ii
3-10 PC HEALTH STATUS.................................................................................36
3-11 MISCELLANEOUS CONTROL ................................................................ 37
3-12 LOAD STANDARD/OPTIMIZED DEFAULTS .......................................38
3-13 SET SUPERVISOR/USER PASSWORD................................................... 38
CHAPTER 4 DRIVER & FREE PROGRAM INSTALLATION
MAGIC INSTALL SUPPORTS WINDOWS 95/98/98SE/NT4.0/2000 .............39
4-1 INF
INSTALL INTEL 845 CHIPSET SYSTEM DRIVER
................40
4-2 SOUND
INSTALL ALC201 AUDIO CODEC DRIVER
.........................41
4-3 LAN
INSTALL RTL8100 LA N CONTROLLER DRIVER
................42
4-4 PC-HEALTH
INTEL 845 PC-HEALTH MONITOR
.......................................43
4-4-1
HOW TO UTILIZE PC-HEALTH
....................................................44
4-5 MAGIC BIOS
INSTALL BIOS LIVE UPDATE UTILITY
................................45
4-6 DRICTX8
INSTALL MICROSOFT DIRECTX 8.0 DRIVER
.....................46
4-7 IAA
INSTALL
INTEL APPLICATION ACCELERATOR SOFTWARE
47
4-8 PC-CILLIN
INSTALL PC-CILLIN2000 ANTI-VIRUS PROGRAM
.............47
4-9 HOW TO DISABLE ON-BOARD SOUND.................................................49
4-10 HOW TO UPDATE BIOS.............................................................................49
USER’S NOTICE
COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS
MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE
REPRODUCED, TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM
OR BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER.
THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE I407/I407L MOTHERBOARD AND WE DO ASSURE THIS MANUAL MEETS U SER’S REQUIREMEN T BU T WILL
CHANGE, CORRECT ANY TIME WITHOUT NOTICE. MANUFACTURER PROVIDES THIS
MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, AND WILL NOT BE LIABLE FOR
ANY INDIRECT, SPECIAL, INCIDENTIAL OR CONSEQUENTIAL DAMAGES (INCLUDING
DAMANGES FOR LOSS OF PROFIT, LOSS OF BUSINESS, LOSS OF USE OF DATA,
INTERRUPTION OF BUSINESS AND THE LIKE).
PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY
NOT BE REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE
COMPANIES, AND THEY ARE USED ONLY FOR IDENTIFICATION OR EXPLANATION
AND TO THE OWNER’S BENEFIT, WITHOUT INTENT TO INFRINGE.
1
Manual Revision Information
Reversion Revision History Date
1.0 First Release December 2001
Item Checklist
5 I407/I407L motherboard
5 Cable for IDE/Floppy
5 CD for motherboard utilities
□
Cable for USB Port 3/4 (Option)
5 I407/I407L User’s Manual
Intel Pentium 4 Processor Family
Cooling Solutions
As processor technology pushes to faster speeds and higher performance, thermal
management becomes increasingly crucial when building computer systems.
Maintaining the proper thermal environment is key to reliable, long-term system
operation. The overall goal in providing the proper thermal environment is keeping the
processor below its specified maximum case temperature. Heatsinks induce improved
processor heat dissipation through increased surface area and concentrated airflow
from attached fans. In addition, interface materials allow effective transfers of heat
from the processor to the heatsink. For optimum heat transfer, Intel recommends the
use of thermal grease and mounting clips to attach the heatsink to the processor.
When selecting a thermal solution for your system, please refer to the website below
for collection of heatsinks evaluated and recommended by Intel for use with Intel
processors. Note, those heatsinks are recommended for maintaining the specified
Maximum T case requirement. In addition, this collection is not intended to be a
comprehensive listing of all heatsinks that support Intel processors.
For vendor list of heatsink and fan, please visit :
http://developer.intel.com/design/Pentium4/components/index
2
Chapter 1
Introduction of I407/I407L Motherboard
1-1 Feature of motherboard
The I407/I407L motherboard is design for use Intel Pentium 4 Processor in 478 Pin
Package/Northwood Processor with the Intel 845 Chipset delivers a high performance
and professional desktop platform solution. Which utilize the Socket 478 design and
the memory size expandable to 2.0GB.
This motherboard use the newest Intel 845 Chipset Supports 400MHz System Bus in
data transfer rate and 133MHz SDRAM clock frequency support DDR200/DDR266
SDRAM. The I407/I407L motherboard offers ULTRA ATA
100
to provide speedier
HDD throughout that boosts overall system performance.
I407L Integrated PCI Fast Ethernet Controller chip support 10/100 BASE-T transfer
rate.
These motherboards also has an integrated AC’97 2.1 CODEC on board which is fully
compatible with Sound Blaster Pro
that gives you the best sound quality and
compatibility.
For those wanting even greater graphic performanc e , a n A G P 4 X s l o t i s i n c l u d e d o n t h e
board.
(For 1.5V AGP card only. No for 3.3V or Universal AGP card).
With USB control as well as capability of expanding to 4 USB function ports, the
I407/I407L meet future USB demand also this motherboard has built-in hardware
monitor function. This will monitor and protect your computer. The I407/I407L
motherboards
integrated Recovery Genius in BIOS
protected your hard disk from
virus crash hard disk data, and special design in hardware to protect BIOS from virus
crash BIOS data.
These motherboards provide special function in BIOS Setup to setting CPU Host clock
step by step increasing let users to approach over clocking.
I407/I407L provides high performance & meets future specification demand. It is
really wise choice for your computer.
1-2 Specification
3
Spec Description
Design
∗
Micro ATX form factor 4 layers PCB size: 24.5x22.0cm
Chipset
∗
Intel 845 Memory Controller Hub (MCH) Chipset
∗
Intel 82801BA I/O Controller Hub (ICH2) Chipset
CPU Socket
(mPGA478B Socket)
∗
Support Intel Pentium 4 478 Pin package utilizes Flip-
Chip Pin Grid Array (FC-PGA2) package processor
∗
Support 1.5G∼2.2G 478 Pin Pentium 4 processor
∗
Reserves support for future Intel Pentium 4 processors
Memory Socket
∗
184-pin DDR SDRAM module socket x2
∗
Support DDR200/DDR266 SDRAM
∗
Expandable to 2.0GB
Expansion Slot &
Headers
∗
AGP slot x1 for AGP 1.5V standard only, support AGP 4X
mode
∗
32-bit PCI slot x3
∗
CNR slot x1
Integrate IDE
∗
Two PCI IDE controllers support PCI Bus Mastering, ATA
PIO/DMA and the ULTRA DMA 33/66/100 functions that
deliver the data transfer rate up to 100 MB/s
LAN
(Only for I407L)
∗
RealTek RTL8100 PCI Ethernet Controller chip
∗
Support 10/100 Mbps transfer rate
Audio
∗
AC’97 Digital Audio controller integrated
∗
AC’97 Audio CODEC on board
∗
Audio driver and utility included
BIOS
∗
Award 2MBit Flash ROM
Multi I/O
∗
PS/2 keyboard and PS/2 mouse connectors
∗
Floppy disk drive connector x1
∗
Parallel port x1
∗
Serial port x2
∗
USB connector x2
∗
USB headers x2 (connecting cable option)
∗
Audio connector (Line-in, Line-out , MIC & Game Port)
1-3 Performance List
4
The following performance data list is the testing result of some popular benchmark
testing programs. These data are just referred by users, and there is no responsibility
for different testing data values gotten by users (the different Hardware & Software
configuration will result in different benchmark testing results.)
Performance Test Report
CPU:
Intel Pentium 4 1.9GHz mPGAB package
DRAM:
128MB DDR266 x2 (SAMSUNG K4H280838B-TCB0)
VGA Expansion Card:
NVDIA Geforce2 MX400 64M (1024x768 Hi-color)
Hard Disk Driver:
IBM DTLA-305040 (ATA-100)
BIOS:
Award Optimal default
OS:
Win 98SE
Performance Test Report
Pentium 4 1.9GHz
3D Mark 2000 5469
3D Mark 2001 2522
3D Winbench 2000 104
Final Reality 10.10
Content Creation Winstone 2000 43.6
Content Creation Winstone 2001 55.8
Business Winstone2001 47.4
Winbench 99:
CPU Mark 99 110
FPU Winmark 99 6630
Business Disk Winmark99 5200
Hi-end Disk Winmark99 17600
Business Graphic Winmark 431
Hi-end Graphic Winmark 1250
SYS Mark 2000 : SISMark 2000 Rating (Internet Content Creation / Office
Productivity)
SISMark 2000 214 (229/203)
SISMark 2001 153 (175/133)
SISOFT Sandra 2001 :
Dhrystone ALU MIPS 3634
Whetstone FPU MFLOPS 1141/2363
Int ALU/RAM MB/S 1017
Float FPU/RAM MB/S 1029
Integer SSE2 IT/S 7577
Floating- Point SSE2 MB/S 9367
QUAKE3 DEMO1 FPS 169.3
DEMO2 FPS 169.8
WCPUID System/CPU Clock 101/1918.94
1-4 Layout Diagram & Jumper Setting
5
Jumpers
Jumper Name Description Page
Front Panel Audio
PC99 Back Panel
CD Audio Conn.
Winbond 83627HF
Chip
IR Connector
CNR Slot
PCI Slot
AGP Slot
K/B Power ON
Jumper (JP1)
Wake On LAN
USB Port /
LAN Connector
(Only for I407L)
PS2 KB/Mouse Port
Floppy Connector
Intel 845 MCH Chip
Front Panel Connector
ATA 100 IDE
Connector
Clear CMOS (JBAT)
ATX Power Conn.
USB Port (USB1)
CPU FAN
478Pin CPU Socket
DDR 200/266 DIMMX2
2MBit Flash ROM BIOS
Wake On Modem
SYSFAN2
Intel 82801BA Chip
SYSFAN
ATX P9 Power Conn.
ATX 12V Conn.
COM1 COM2
PS/2 MOUSE
PS/2 Keyboard
USB
LINE-OUT
LINE-IN
MIC
PRINT GAME/MIDI PORT
LAN
RTL 8100 LAN Chip
(Only for I407L)
6
JBAT CMOS RAM Clear 3-pin Block P.7
JP1 Keyboard Power On Enable/Disabled 3-pin Block P.8
Connectors
Connector Name Description Page
ATXPWR ATX Power Connector 20-pin Block P.13
ATX12V ATX 12V Power Connector 4-pin Block P.13
ATXP9 ATX P9 Power Connector 6-pin Block P.14
J1 PS/2 Mouse & PS/2 Keyboard
Connector
6-pin Female P.14
USB USB Port Connector 4-pin Connector P.14
LAN RJ45 LAN Connector RJ45 Connector P.14
PARALL Parallel Port Connector 25-pin Female P.14
AUD_GAME Audio/Game Connector 3 phone jack + 15-pin Connector P.14
COM1/COM2 Serial Port COM1/2 Connector 9-pin Connector P.14
FDD Floppy Driver Connector 34-pin Block P.15
IDE1/IDE2 Primary/Secondary IDE Connector 40-pin Block P.15
Only for I407L
Headers
Header Name Description Page
AUDIO Line-In/Out, MIC header 9-pin Block P.16
USB1 USB Port Headers 9-pin Block P.16
IDE LED IDE activity LED 2-pin Block P.17
TURBO LED Turbo LED switch 2-pin Block P.17
RESET Reset switch lead 2-pin Block P.17
SPKR Speaker connector 4-pin Block P.17
PWR-LED Power LED 2-pin Block P.17
PWR BTN Power switch 2-pin Block P.17
WOL/WOM Wake On-LAN/Modem Headers 3-pin Block P.18
SYSFAN, SYSFAN2,
CPUFAN
FAN Speed Headers 3-pin Block P.18
IR IR infrared module Headers 5-pin Block P.18
CDIN CD Audio-In Headers 4-pin Block P.19
Expansion Sockets
Socket/Slot Name Description Page
ZIF Socket 478 CPU Socket 478-pin mPGAB CPU Socket P.9
DIMM1, DIMM2 DDR Module Socket 184-pin DDR Module Expansion
Socket
P.10
PCI1 ∼ PCI3
PCI Slot 32-bit PCI Local Bus Expansion slots P.11
AGP AGP 4X Mode Slot AGP Expansion Slot P.12
CNR CNR Slot Communication Network Riser Slot
Chapter 2
Hardware installation
7
2-1 Hardware installation Steps
Before using your computer, you had better complete the following steps:
1. Check motherboard jumper setting
2. Install CPU and Fan
3. Install System Memory (DIMM)
4. Install Expansion cards
5. Connect IDE and Floppy cables, Front Panel /Back Panel cable
6. Connect ATX Power cable
7. Power-On and Load Standard Default
8. Reboot
9. Install Operating System
10. Install Driver and Utility
2-2 Checking Motherboard’s Jumper Setting
(1) CMOS RAM Clear (3-pin) : JBAT
A battery must be used to retain the motherboard configuration in CMOS RAM short 1-2
pins of JBAT to store the CMOS data.
To clear the CMOS, follow the procedure below:
1. Turn off the system and unplug the AC power
2. Remove ATX power cable from ATX power connector
3. Locate JBAT and short pins 2-3 for a few seconds
4. Return JBAT to its normal setting by shorting pins 1-2
5. Connect ATX power cable back to ATX power connector
Note: When should clear CMOS
1. Troubleshooting
2. Forget password
3. After over clocking system boot fail
CMOS RAM Clear Setting
2-3 closed Clear CMOS
JBAT
1
3
JBAT
1
3
1-2 closed Normal
(2) Keyboard Power On function Enabled/Disabled: JP1
When setting Enabled you can using keyboard by key in password to power on system.
8
Keyboard Power On Setting
2-3 closed K/B Power ON Enabled
JP1
1 3
JP1
13
1-2 closed K/B Power ON Disable
(
Default
)
2-3 Install CPU
2-3-1 Glossary
Chipset (or core logic) - two or more integrated circuits which control the interfaces
between the system processor, RAM, I/O devises, and adapter cards.
Processor slot/socket - the slot or socket used to mount the system processor on the
motherboard.
Slot (AGP, PCI, ISA, RAM) - the slots used to mount adapter cards and system RAM.
AGP - Accelerated Graphics Port - a high speed interf ace for video cards; runs at 1X
(66MHz), 2X (133MHz), or 4X (266MHz).
PCI - Peripheral Component Interconnect - a high speed interface for video cards,
sound cards, network interface cards, and modems; runs at 33MHz.
ISA - Industry Standard Architecture - a relatively low speed interface primarily used
for sound cards and modems; runs at approx. 8MHz.
Serial Port - a low speed interface typically used for mouse and external modems.
Parallel Port - a low speed interface typically used for printers.
PS/2 - a low speed interface used for mouse and keyboards.
USB - Universal Serial Bus - a medium speed interface typically used for mouse,
keyboards, scanners, scanners, and some digital cameras.
Sound (interface) - the interface between the sound card or integrated sound
connectors and speakers, MIC, game controllers, and MIDI sound devices.
LAN (interface) - Local Area Network - the interface to your local area network.
BIOS (Basic Input/Output System) - the program logic used to boot up a computer and
establish the relationship between the various components.
Driver - software, which defines the characteristics of a device for use by another
device or other software.
Processor - the "central processing unit" (CPU); the principal integrated circuit used
9
for doing the "computing" in "personal computer"
Front Side Bus Frequency -
the working frequency of the motherboard, which is
generated by the clock generator for CPU, DRAM and PCI BUS.
CPU L2 Cache -
the flash memory inside the CPU, normally Pentium 4 CPU has
256K.
2-3-2 About Intel Pentium 4 478-pin CPU
This motherboard provides a 478-pin surface mount, Zero Insertion Force (ZIF) socket,
referred to as the mPGA478B socket supports Intel Pentium 4 processor in the 478 Pin
package utilizes Flip-Chip Pin Grid Array (FC-PGA2) package technology.
The CPU that comes with the motherboard should have a cooling FAN attached to
prevent overheating. If this is not the case, then purchase a correct cooling FAN before
you turn on your system.
WARNING!
Be sure that there is sufficient air circulation across the processor’s
heatsink and CPU cooling FAN is working correctly, otherwise it may
cause the processor and motherboard overheat and damage, you may install
an auxiliary cooling FAN, if necessary.
To install a CPU, first turn off your system and remove its cover. Locate the ZIF
socket and open it by first pulling the level sideways away from the socket then
upward to a 90-degree angle. Insert the CPU with the correct orientation as shown
below. The notched corner should point toward the end of the level. Because the CPU
has a corner pin for two of the four corners, the CPU will only fit in the orientation as
shown.
CPU ZIF mPGAB Socket
Colden Arrow
mPGA478B
When you put the CPU into the ZIF socket. No force require to insert of the CPU, then
press the level to Locate position slightly without any extra force.
2-4 Install Memory
This motherboard provides two 184-pin DUAL INLINE MEMORY MODULES
(DIMM) sites for memory expansion available from minimum memory size of 64MB
to maximum memory size of 2.0GB DDR (Double Data Rate) SDRAM.
10
Valid Memory Configurations
Bank 168-Pin DIMM Total Memory
Bank 0, 1 (DDR1) DDR200/DDR266 SDRAM Module X1 64MB∼1.0GB
Bank 2, 3 (DDR2) DDR200/DDR266 SDRAM Module X1 64MB∼1.0GB
Total System Memory (Max. 2.0GB) 2 64MB∼2.0GB
NOTE!
Make sure the installed memory are DDR266 SDRAM support 133MHz memory
clock, otherwise the system may hang during startup.
Generally, installing DDR SDRAM modules to your motherboard is very easy, you
can refer to figure 2-4 to see what a 184-Pin DDR200/DDR266 SDRAM module
looks like.
DDR2 (BANK2+ BANK3)
DDR1 (BANK0+ BANK1)
NOTE!
When you install DIMM module fully into the DIMM socket the eject tab
should be locked into the DIMM module very firmly and fit into its
indention on both sides.
WARNING!
For the DDR SDRAM CLOCK is set at 133MHz, use only DDR266compliant DDR Modules. When this motherboard operate at 133Mhz, most
system will not even boot if non-compliant modules are used because of the
strict timing issues, if your DDR Modules are not DDR266-compliant, set
the DDR SDRAM clock to 100MHz to ensure system stability.
2-5 Expansion Cards
WARNING!
Turn off your power when adding or removing expansion cards or other
system components. Failure to do so may cause severe damage to both
your motherboard and expansion cards.
Figure 2-4
11
2-5-1 Procedure For Expansion Card Installation
1. Read the documentation for your expansion card and make any necessary hardware
or software setting for your expansion card such as jumpers.
2. Remove your computer’s cover and the bracket plate on the slot you intend to use.
3. Align the card’s connectors and press firmly.
4. Secure the card on the slot with the screen you remove above.
5. Replace the computer system’s cover.
6. Set up the BIOS if necessary.
7. Install the necessary software driver for your expansion card.
2-5-2 Assigning IRQs For Expansion Card
Some expansion cards need an IRQ to operate. Generally, an IRQ must exclusively
assign to one use. In a standard design, there are 16 IRQs available but most of them
are already in use.
Standard Interrupt Assignments
IRQ Priority Standard function
0 N/A System Timer
1 N/A Keyboard Controller
2 N/A Programmable Interrupt
3 * 8 Communications Port (COM2)
4 * 9 Communications Port (COM1)
5 * 6 Sound Card (sometimes LPT2)
6 * 11 Floppy Disk Controller
7 * 7 Printer Port (LPT1)
8 N/A System CMOS/Real Time Clock
9 * 10 ACPI Mode when enabled
10 * 3 IRQ Holder for PCI Steering
11 * 2 IRQ Holder for PCI Steering
12 * 4 PS/2 Compatible Mouse Port
13 N/A Numeric Data Processor
14 * 5 Primary IDE Channel
15 * 1 Secondary IDE Channel
* These IRQs are usually available for ISA or PCI devices.
2-5-3 Interrupt Request Table For This Motherboard
Interrupt request are shared as shown the table below:
INT A INT B INT C INT D INT E INT F INT G INT H
Slot 1
√
Slot 2
√
Slot 3
√
Onboard LAN
√
Onboard USB 1
√
Onboard USB 2
√
12
AC97/MC97
√
IMPORTANT!
If using PCI cards on shared slots, make sure that the drivers support
“S hared IRQ” or that the cards don’t need IRQ assignments. C onflicts will
arise between the two PCI groups that will make the system unstable or
cards inoperable.
2-5-4 AGP Slot
This motherboard provides an AGP Slot, only support the 1.5V 4X AGP VGA card.
Do not use AGP 2X card (3.3V) in this motherboard. It will burn and damage the
motherboard due to Intel® 845 chipset can not support AGP 2X (3.3V)
IMPORTANT!
Before you plug-in AGP card, please make sure the following notice is
fully understood and practiced. If your AGP card has “AGP 4X notch
(show below) please make sure your AGP card is AGP 4X (1.5V) not
AGP 2X (3.3V)
AGP SLOT
Example 1:
SiS 305 & ATi Rage 128 Pro AGP card those golden finger is compatible
with 2X/4X mode AGP slot, but only can support 2X (3.3V) only. If you
install these cards in Intel® 845 based motherboard it will burn and damage
the motherboard.
Example 2:
We also find Diamond Vipper V770 golden finger is design for 2X/4X mode
AGP Slot. It can be adjusted the jumper for AGP 2X (3.3V) or AGP 4X
(1.5V). But the factory default setting is 2X (3.3V). If you install this AGP
card in motherboard without change the jumper setting to 4X (1.5V), it will
burn the motherboard.
2-6 Connectors, Headers
2-6-1 Connectors
2x notch 4x notch
13
(1) Power Connector (20-pin block) : ATXPWR
ATX Power Supply connector. This is a new defined 20-pins connector that usually
comes with ATX case. The ATX Power Supply allows to use soft power on momentary
switch that connect from the front panel switch to 2-pins Power On jumper pole on the
motherboard. When the power switch on the back of the ATX power supply turned on,
the full power will not come into the system board until the front panel switch is
momentarily pressed. Press this switch again will turn off the power to the system
board.
PIN ROW2 ROW1
1 3.3V 3.3V
2 -12V 3.3V
3 GND GND
4 Soft Power On 5V
5 GND GND
6 GND 5V
7 GND GND
8 -5V Power OK
9 +5V +5V (for Soft Logic)
10 +5V +12V
Pin 1
(2) ATX 12V Power Connector (4-pin block) : ATX12V
This is a new defined 4-pins connector that usually comes with ATX Power Supply. The
ATX Power Supply which fully support Pentium 4 processor must including this
connector for support extra 12V voltage to maintain system power consumption.
Without this connector might cause system unstable because the power supply can not
provide sufficient current for system.
Pin 1
(3) ATX P9 Power Connector (6-pin block) : ATXP9
This is a new defined 6-pins connector that usually comes with ATX Power
Supply. The ATX Power Supply which fully support Pentium 4 processor must
including this connector for support extra 3.3V and 5V voltage to maintain
system power consumption. Without this connector might cause system unstable
because the power supply can not provide sufficient current for system.
Loading...