JETWAY I401-R, I401 User Manual

I401-R/I401
USER'S MANUAL
M/B For Socket 478 Pentium 4 Processor
NO. G03-I401R5A
Release date: October 2001
Trademark:
* Specifications and Information contained in this documentation are furnished for information use only, and are
subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
i
USER’S NOTICE................................................................................ii
MANUAL REVISION INFORMATION..............................................1
COOLING SOLUTIONS ...................................................................1
CHAPTER 1 INTRODUCTION OF I401-R/I401 MOTHERBOARD
1-1 FEATURE OF MOTHERBOARD ...............................................2
1-2 SPECIFICATION .................................................................... 3
1-3 PERFORMANCE LIST.............................................................4
1-4 LAYOUT DIAGRAM & JUMPER SETTING ................................5
CHAPTER 2 HARDWARE INSTALLATION
2-1 HARDWARE INSTALLATION STEPS........................................ 7
2-2 CHECKING MOTHERBAORD'S JUMPER SETTING....................7
2-3 INSTALL CPU........................................................................9
2-3-1 GLOSSARY...........................................................................9
2-3-2
ABOUT INTEL PENTIUM 4 478-PIN CPU
.............................10
2-4 INSTALL MEMORY................................................................11
2-5 EXPANSION CARD.................................................................12
2-5-1 PROCEDURE FOR EXPANSION CARD INSTALLATION .............12
2-5-2 ASSIGNING IRQ FOR EXPANSION CARD.................................
12
2-5-3 INTERRUPT REQUEST TABLE FOR THIS MOTHERBOARD.......
13
2-5-4 AGP SLOT ............................................................................
13
2-6 CONNECTORS, HEADERS.......................................................14
2-6-1 CONNECTORS ......................................................................
14
2-6-2 HEADERS.............................................................................18
2-7 STARTING UP YOUR COMPUTER ........................................... 21
CHAPTER 3 INTRODUCING BIOS
3-1 ENTERING SETUP..................................................................22
3-2 GETTING HELP ..................................................................... 23
3-3 THE MAIN MENU...................................................................23
3-4 STANDARD CMOS FEATURES.................................................24
3-5 ADVANCED BIOS FEATURES..................................................26
3-6 ADVANCED CHIPSET FEATURES............................................ 28
3-6-1 DRAM TIMING SETTINGS.............................................29
3-7 INTEGRATED PERIPHERALS.................................................. 29
3-7-1 ONCHIP IDE FUNCTION ...............................................30
3-7-2 ONCHIP DEVICE FUNCTION ......................................... 31
3-7-3 ONCHIP SUPER IO FUNCTION ......................................32
3-8 POWER MANAGEMENT SETUP...............................................33
3-8-1 PM TIMER RELOAD EVENTS........................................35
3-9 PNP/PCI CONFIGURATION SETUP ..........................................35
3-9-1 IRQ RESOURCES .........................................................36
TABLE OF CONTENT
ii
3-10 PC HEALTH STATUS.............................................................37
3-11 MISCELLANEOUS CONTROL.................................................38
3-12 LOAD STANDARD/OPTIMIZED DEFAULTS ............................. 39
3-13 SET SUPERVISOR/USER PASSWORD ......................................39
CHAPTER 4 DRIVER & FREE PROGRAM INSTALLATION
MAGIC INSTALL SUPPORTS WINDOWS 95/98/98SE/NT4.0/2000......... 40
4-1 INF
INSTALL INTEL 845 CHIPSET SYSTEM DRIVER
............41
4-2 IDE
INSTALL INTEL 845 ULTRA ATA DRIVER
....................42
4-3 SOUND
INSTALL ALC201 AUDIO CODEC DRIVER
...................43
4-4 ATA100
PROMISE ATA100/RAID DRIVER MANUAL
(ONLY FOR I401-R)
...............................................44
4-4-1 INSTALL PROMISE ATA100 IDE CONTROLLER DRIVER.44
4-4-2 INSTALL PROMISE IDE RAID CONTROLLER DRIVER....45
4-4-3 INSTALL PROMISE IDE RAID CONTROLLER UTILITY... 45 4-5 PC-HEALTH
WINBOND HARDWARE DOCTOR MONITORING SOFTWARE
........................................................................47
4-5-1
HOW TO UTILIZE PC-HEALTH
.......................................48
4-6 MAGIC BIOS
INSTALL BIOS LIVE UPDATE UTILITY
........................49
4-7 PC-CILLIN
INSTALL PC-CILLIN2000 ANTI-VIRUS PROGRAM
..........51
4-8 HOW TO DISABLE ON-BOARD SOUND .................................... 53
4-9 HOW TO UPDATE BIOS..........................................................53
USER’S NOTICE
COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED, TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER.
THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE I401-R/I401 MOTHER­BOARD AND WE DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT WILL CHANGE, CORRECT ANY TIME WITHOUT NOTICE. MANUFACTURER PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, AND WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTIAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMANGES FOR LOSS OF PROFIT, LOSS OF BUSINESS, LOSS OF USE OF DATA, INTERRUPTION OF BUSINESS AND THE LIKE).
PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES, AND THEY ARE USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER’S BENEFIT, WITHOUT INTENT TO INFRINGE.
1
Manual Revision Information
Reversion Revision History Date
5.0 Fifth Edition October 2001
Item Checklist
I401-R/I401 motherboard
Cable for IDE/Floppy
CD for motherboard utilities
Cable for USB Port 3/4 (Option)
Cable for IDE RAID (only for I401-R)
I401-R/I401 User’s Manual
Intel Pentium 4 Processor Family
Cooling Solutions
As processor technology pushes to faster speeds and higher performance, thermal management becomes increasingly crucial when building computer systems. Maintaining the proper thermal environment is key to reliable, long-term system operation. The overall goal in providing the proper thermal environment is keeping the processor below its specified maximum case temperature. Heatsinks induce improved processor heat dissipation through increased surface area and concentrated airflow from attached fans. In addition, interface materials allow effective transfers of heat from the processor to the heatsink. For optimum heat transfer, Intel recommends the use of thermal grease and mounting clips to attach the heatsink to the processor. When selecting a thermal solution for your system, please refer to the website below for collection of heatsinks evaluated and recommended by Intel for use with Intel processors. Note, those heatsinks are recommended for maintaining the specified Maximum T case requirement. In addition, this collection is not intended to be a comprehensive listing of all heatsinks that support Intel processors.
For vendor list of heatsink and fan, please visit : http://developer.intel.com/design/Pentium4/components/index
2
Chapter 1
Introduction of I401-R/I401 Motherboard
1-1 Feature of motherboard
The I401-R/I401 motherboard is design for use Intel Pentium 4 Processor in 478 Pin Pack age /N ort hw ood Processor with the Intel 845 Chipset delivers a hi gh pe rf orm an ce and professional desktop platform solution. Which utilize the Socket 478 design and the memory size expandable to 3.0GB.
This motherboard use the newest Intel 845 Chipset Supports 400MHz System Bus in data transfer rate and 133MHz SDRAM clock frequency support PC133/SDRAM . The I401-R/I401 motherboard offers ULTRA ATA 100 to provide speedier HDD throughout that boosts overall system performance.
The I401-R motherboard including IDE RAID chipset and added extra 2 channel IDE interface supports either ATA100, or RAID0 (striping), RAID1 (mirroring) function. Use RAID0 function it can increasing data storage performance, use RAID1 function it can protect data which save in hard disk drive.
These motherboards also has an integrated AC’97 2.1 CODEC on board which is fully compatible with Sound Blaster Pro
that gives you the best sound quality and
compatibility. For those wanting even greater graphic perf orman ce, an A GP 4X s lot is i nclud ed on
the board. (For 1.5V AGP card only. No for 3.3V or Universal AGP card). With USB control as well as capability of expanding to 4 USB function ports, the
I401-R/I401 meet future USB demand also this motherboard has built-in hardware monitor function. This will monitor and protect your computer. The I401 motherboards integrated Recovery Genius in BIOS protected your hard disk from virus crash hard disk data, and special design in hardware to protect BIOS from virus crash BIOS data.
In I401-R/I401 we design in CPU Vcore Voltage, System 3.3V Voltage, System memory 3.3V Voltage, AGP 1.5V/3.3V Voltage those can minor adjustable in BIOS setup. This design can let users approach over clock demand and also can make system more stable. The I401-R/I401 motherboard provides special function in
BIOS Setup to setting CPU Host clock step by step increasing let users to approach over clocking.
I401-R/I401 provides high performance & meets future specification demand. It is really wise choice for your computer.
3
1-2 Specification
Spec Description
Design
ATX form factor 4 layers PCB size: 30.5x24.4cm
Chipset
Intel 845 Memory Controller Hub (MCH) Chipset
Intel 82801BA I/O Controller Hub (ICH2) Chipset
PROMISE PDC20265R IDE RAID chip for I401-R only
CPU Socket
(mPGA478B Socket)
Support Intel Pentium 4 478 Pin package utilizes Flip-
Chip Pin Grid Array (FC-PGA2) package processor
Support 1.5G∼2.0G 478 Pin Pentium 4 processor
Reserves support for future Intel Pentium 4 processors
Memory Socket
168-pin SDR SDRAM module socket x3
Support PC133 SDRAM
Expandable to 3.0GB
Expansion Slot & Headers
AGP slot x1 for AGP 1.5V standard only, support AGP
2.0 & 4X mode
32-bit PCI slot x5
CNR slot x1
Integrate IDE
Two PCI IDE controllers support PCI Bus Mastering, ATA PIO/DMA and the ULTRA DMA 33/66/100 functions that deliver the data transfer rate up to 100 MB/s
IDE RAID (Only for I401-R)
2 channel IDE RAID interface supports either ATA100 or RAID0, RAID1 function
Audio
AC’97 Digital Audio controller integrated
AC’97 Audio CODEC on board
Audio driver and utility included
BIOS
Award 2MB Flash ROM
Multi I/O
PS/2 keyboard and PS/2 mouse connectors
Floppy disk drive connector x1
Parallel port x1
Serial port x2
USB connector x2
USB headers x2 (connecting cable option)
Audio connector (Line-in, Line-out , MIC & Game Port)
4
1-3 Performance List
The following performance data list is the testing result of some popular benchmark testing programs. These data are just referred by users, and there is no responsibility for different testing data values gotten by users (the different Hardware & Software configuration will result in different benchmark testing results.)
Performance Test Report
CPU: Intel Pentium 4 1.5GHz mPGAB package DRAM: 128M SDRAM x2 (Hyundai GM 72V66841ET75) VGA Expansion Card: Geforce 256 (1024x768 Hi-color) Driver V3.68 Hard Disk Driver: IBM DTLA-305040 (ATA-100) BIOS: Award Optimal default OS: Win 98SE
Performance Test Report
Pentium 4 1.5GHz
3D Mark 99 5998 3D Mark 2000 4706 3D Mark 2001 1881 3D Winbench 99 V1.2 900 3D Winbench 2000 94 Final Reality 7.57 Winstone 99 V1.3 27.3 Content Creation Winstone 2000 37.1 Content Creation Winstone 2001 44.1 Business Winstone2001 39.1
Winbench 99:
CPU Mark 99 85.6 FPU Winmark 99 5130 Business Disk Winmark99 7750 Hi-end Disk Winmark99 20300 Business Graphic Winmark 342 Hi-end Graphic Winmark 973
SYS Mark 2000 : SISMark 2000 Rating (Internet Content Creation / Office Productivity)
Suites 173 (185/164) Official 173 (186/163)
SISOFT Sandra 2000 :
Dhrystone ALU MIPS
2790
Whetstone FPU MFLOPS
1843
Int ALU/RAM MB/S
658
Float FPU/RAM MB/S
658
QUAKE3 DEMO1 FPS
131.6
5
DEMO2 FPS
130.0
1-4 Layout Diagram & Jumper Setting
COM1 COM2
PS/2 MOUSE
PS/2 Keyboard
USB
LINE-OUT
LINE-IN
MIC
PRINT GAME/MIDI PORT
ATA100/RAID Mode Selector
(JP14)
Winbond 83697HF
Chip
IR Connector
CNR Slot
Front Panel Audio
PC99 Back Panel
CD Audio
PCI Slot
AGP Slot
K/B Power ON Jumper (JP1)
Floppy Connector
Intel 845 Chip
Front Panel Connector
ATA 100 IDE Connector
Clear CMOS (JP3)
ATX Power Conn.
USB Port
CPU FAN
2M Flash ROM BIOS
CPU Socket
PC133 DIMMX3
IDE RAID Connector (for I401-R)
PDC20265 Chip
Wake On Modem
Wake On LAN
SYSFAN
Intel 82801BA Chip
(JP4)
USB Power On Jumper
ATX 12V Power Conn.
USB Port
PS2 KB/Mouse Port
SYSFAN2
ATX P9 Power Conn.
6
Jumpers
Jumper Name Description Page
JP3 CMOS RAM Clear 3-pin Block P.7
JP1 Keyboard Power On Enable/Disabled 3-pin Block P.8 JP4 USB Power On Enable/Disabled 3-pin Block P.8
JP14 ATA 100/RAID Mode Selector 3-pin Block (for I401-R) P.8
Connectors
Connector Name Description Page
ATXPWR ATX Power Connector 20-pin Block P.14 ATX12V ATX 12V Power Connector 4-pin Block P.14 ATXP9 ATX P9 Power Connector 6-pin Block P.15 PS2 KB/MOUSE
PS/2 Mouse & PS/2 Keyboard Connector
6-pin Female P.15
USB1 USB Port Connector 4-pin Connector P.15 PRINT Parallel Port Connector 25-pin Female P.15 AUD_GAME Audio/Game Connector 3 phone jack + 15-pin Connector P.15 COM1/COM2 Serial Port COM1/2 Connector 9-pin Connector P.15 FDD Floppy Driver Connector 34-pin Block P.16 IDE1/IDE2 Primary/Secondary IDE Connector 40-pin Block P.17
IDE3/IDE4 IDE RAID Connectors 40-pin Block (for I401-R) P.17
Headers
Header Name Description Page
AUDIO Line-In/Out, MIC header 9-pin Block P.18 USB2 USB Port Headers 9-pin Block P.18 IDE LED IDE activity LED 2-pin Block P.18 TURBO LED Turbo LED switch 2-pin Block P.18 RESET Reset switch lead 2-pin Block P.18 SPKR Speaker connector 4-pin Block P.19
PWR-LED
Power LED 2-pin Block P.19 PWR BTN Power switch 2-pin Block P.19 WOL/WOM Wake On-LAN/Modem Headers 3-pin Block P.19 SYSFAN,SYSFAN2, CPUFAN
FAN Speed Headers 3-pin Block P.20
IR IR infrared module Headers 5-pin Block P.20 CDIN CD Audio-In Headers 4-pin Block P.20
Expansion Sockets
Socket/Slot Name Description Page
ZIF Socket 478 CPU Socket 478-pin mPGAB CPU Socket P.10 D I M M 1 , D I M M 2 , D I M M 3 SDRAM Module
Socket
168-pin SDR SDRAM Module Expansion Socket
P.11
PCI1 ∼ PCI5
PCI Slot 32-bit PCI Local Bus Expansion slots P.12
7
AGP AGP 4X Mode Slot AGP Expansion Slot P.13 CNR CNR Slot Communication Network Riser Slot
Chapter 2
Hardware installation
2-1 Hardware installation Steps
Before using your computer, you had better complete the following steps:
1. Check motherboard jumper setting
2. Install CPU and Fan
3. Install System Memory (DIMM)
4. Install Expansion cards
5. Connect IDE and Floppy cables, Front Panel /Back Panel cable
6. Connect ATX Power cable
7. Power-On and Load Standard Default
8. Reboot
9. Install Operating System
10. Install Driver and Utility
2-2 Checking Motherboard’s Jumper Setting
1. CMOS RAM Clear (3-pin) : JP3
A battery must be used to retain the motherboard configuration in CMOS RAM short 1-2 pins of JP3 to store the CMOS data.
To clear the CMOS, follow the procedure below:
1. Turn off the system and unplug the AC power
2. Remove ATX power cable from ATX power connector
3. Locate JP3 and short pins 2-3 for a few seconds
4. Return JP3 to its normal setting by shorting pins 1-2
5. Connect ATX power cable back to ATX power connector
Note: When should clear CMOS
1. Troubleshooting
2. Forget password
3. After over clocking system boot fail
CMOS RAM Clear Setting
2-3 closed Clear CMOS
JP3
1
3
JP3
1
3
1-2 closed Normal
8
2. Keyboard Power On function Enabled/Disabled: JP1
When setting Enabled you can using keyboard by key in password to power on system.
Keyboard Power On Setting
2-3 closed K/B Power ON Enabled
JP1
1 3
JP1
1 3
1-2 closed K/B Power ON Disable
(
Default)
3. USB Power On function Enabled/Disabled: JP4
When setting JP1 2-3 closed Enabled Keyboard Power On Function, you can setting JP4 2-3 closed enabled USB Power On Function for using USB device to power on system.
USB Power On function Setting
2-3 closed USB Power ON Enabled
JP4
1 3
JP4
1 3
1-2 closed USB Power ON Disable
(
Default)
4. ATA100/RAID Mode Selector: JP14 (Only for I401-R)
When JP14 1-2 closed the IDE3 & IDE4 are setting in ATA100 Mode supports Ultra DMA 100MB/sec transfer rate. When JP14 2-3 closed the IDE3 & IDE4 are setting in RAID Mode supports RAID 0 (striping) to increase hard drive performance or RAID 1 (mirroring) to protect hard drive data, for more detail information please refer CD-PACK in X:\MANUAL\PROMISE.DOC
Note:
If you only install hard drive in IDE3 and IDE4 and the JP14 setting 2-3 closed
then this driver must install IDE RAID 0 or IDE RAID 1 Mode by Fast Build Utility, please press <Ctrl-F> to enter setup Main Menu and choose “Auto Setup” to setup your hard drive.
9
ATA 100/RAID Mode Selector
2-3 closed RAID Mode
(
Default)
JP14
1 3
JP14
1 3
1-2 closed ATA100 Mode
2-3 Install CPU
2-3-1 Glossary
Chipset (or core logic)
- two or more integrated circuits which control the interfaces
between the system processor, RAM, I/O devises, and adapter cards.
Processor slot/socket
- the slot or socket used to mount the system processor on the
motherboard.
Slot
(AGP, PCI, ISA, RAM) - the slots used to mount adapter cards and system
RAM.
AGP
- Accelerated Graphics Port - a high speed interface for video cards; runs at
1X (66MHz), 2X (133MHz), or 4X (266MHz).
PCI
- Peripheral Component Interconnect - a high speed interface for video cards,
sound cards, network interface cards, and modems; runs at 33MHz.
ISA
- Industry Standard Architecture - a relatively low speed interface primarily
used for sound cards and modems; runs at approx. 8MHz.
Serial Port
- a low speed interface typically used for mouse and external modems.
Parallel Port
- a low speed interface typically used for printers.
PS/2
- a low speed interface used for mouse and keyboards.
USB
- Universal Serial Bus - a medium speed interface typically used for mouse,
keyboards, scanners, scanners, and some digital cameras.
Sound
(interface) - the interface between the sound card or integrated sound
connectors and speakers, MIC, game controllers, and MIDI sound devices.
LAN
(interface) - Local Area Network - the interface to your local area network.
BIOS (B
asic Input/Output System) - the program logic used to boot up a computer
and establish the relationship between the various components.
Driver
- software, which defines the characteristics of a device for use by another
device or other software.
Processor
- the "central processing unit" (CPU); the principal integrated circuit used
for doing the "computing" in "personal computer"
10
Front Side Bus Frequency -
the working frequency of the motherboard, which is
generated by the clock generator for CPU, DRAM and PCI BUS.
CPU L2 Cache -
the flash memory inside the CPU, normally Athlon CPU has 256K
or above, while Duron will have 64K.
2-3-2 About Intel Pentium 4 478-pin CPU
This motherboard provides a 478-pin surface mount, Zero Insertion Force (ZIF) socket, referred to as the mPGA478B socket supports Intel Pentium 4 processor in the 478 Pin package utilizes Flip-Chip Pin Grid Array (FC-PGA2) package technology.
The CPU that comes with the motherboard should have a cooling FAN attached to prevent overheating. If this is not the case, then purchase a correct cooling FAN before you turn on your system.
WARNING!
Be sure that there is sufficient air circulation across the processor’s heatsink and CPU cooling FAN is working correctly, otherwise it may cause the processor and motherboard overheat and damage, you may install an auxiliary cooling FAN, if necessary.
To install a CPU, first turn off your system and remove its cover. Locate the ZIF socket and open it by first pulling the level sideways away from the socket then upward to a 90-degree angle. Insert the CPU with the correct orientation as shown below. The notched corner should point toward the end of the level. Because the CPU has a corner pin for two of the four corners, the CPU will only fit in the orientation as shown.
CPU ZIF mPGAB Socket
Colden Arrow
mPGA478B
Intel
When you put the CPU into the ZIF socket. No force require to insert of the CPU, then press the level to Locate position slightly without any extra force.
11
2-4 Install Memory
This motherboard provides three 168-pin DUAL INLINE MEMORY MODULES (DIMM) sites for memory expansion available from minimum memory size of 64MB to maximum memory size of 3.0GB SDR SDRAM.
Valid Memory Configurations
Bank 168-Pin DIMM Total Memory
Bank 0, 1 (DIMM1) PC133 SDR SDRAM Module X1 64MB∼1.0GB Bank 2, 3 (DIMM2) PC133 SDR SDRAM Module X1 64MB∼1.0GB Bank 4, 5 (DIMM3) PC133 SDR SDRAM Module X1 64MB∼1.0GB
Total System Memory (Max. 3.0GB) 3 64MB∼3.0GB
NOTE! Make sure the installed memory are PC133 SDRAM support 133MHz memory
clock, otherwise the system may hang during startup.
Generally, installing SDR SDRAM modules to your motherboard is very easy, you can refer to figure 2-4 to see what a 168-Pin PC133 SDR SDRAM module looks like.
DDR2 (BANK2+BANK3)
DDR1 (BANK0+BANK1)
DDR3 (BANK4+BANK5)
NOTE! When you install DIMM module fully into the DIMM socket the eject tab
should be locked into the DIMM module very firmly and fit into its indention on both sides.
Figure 2-4
12
WARNING! For the SDR SDRAM CLOCK is set at 133MHz, use only PC133-
compliant SDR Modules. When this motherboard operate at 133Mhz, most system will not even boot if non-compliant modules are used because of the strict timing issues, if your SDR Modules are not PC133-compliant, set the SDR SDRAM clock to 100MHz to ensure system stability.
2-5 Expansion Cards
WARNING! Turn off your power when adding or removing expansion cards or other
system components. Failure to do so may cause severe damage to both your motherboard and expansion cards.
2-5-1 Procedure For Expansion Card Installation
1. Read the documentation for your expansion card and make any necessary hardware or software setting for your expansion card such as jumpers.
2. Remove your computer’s cover and the bracket plate on the slot you intend to use.
3. Align the card’s connectors and press firmly.
4. Secure the card on the slot with the screen you remove above.
5. Replace the computer system’s cover.
6. Set up the BIOS if necessary.
7. Install the necessary software driver for your expansion card.
2-5-2 Assigning IRQs For Expansion Card
Some expansion cards need an IRQ to operate. Generally, an IRQ must exclusively assign to one use. In a standard design, there are 16 IRQs available but most of them are already in use.
Standard Interrupt Assignments
IRQ Priority Standard function
0 N/A System Timer 1 N/A Keyboard Controller 2 N/A Programmable Interrupt 3 * 8 Communications Port (COM2) 4 * 9 Communications Port (COM1) 5 * 6 Sound Card (sometimes LPT2) 6 * 11 Floppy Disk Controller
13
7 * 7 Printer Port (LPT1) 8 N/A System CMOS/Real Time Clock
9 * 10 ACPI Mode when enabled 10 * 3 IRQ Holder for PCI Steering 11 * 2 IRQ Holder for PCI Steering 12 * 4 PS/2 Compatible Mouse Port 13 N/A Numeric Data Processor 14 * 5 Primary IDE Channel 15 * 1 Secondary IDE Channel
* These IRQs are usually available for ISA or PCI devices.
2-5-3 Interrupt Request Table For This Motherboard
Interrupt request are shared as shown the table below:
INT A INT B INT C INT D INT E INT F INT G INT H
Slot 1
Slot 2
Slot 3 √ Slot 4 √ Slot 5 √ Onboard VGA Onboard USB 1 √ Onboard USB 2 √ AC97/MC97
IMPORTANT! If using PCI cards on shared slots, make sure that the drivers support
“Sh ared IRQ” or that the cards don’t need IRQ assi gnme nts. Conf lict s will arise between the two PCI groups that will make the system unstable or cards inoperable.
2-5-4 AGP Slot
This motherboard provides an AGP Slot, only support the 1.5V 4X AGP VGA card. Do not use AGP 2X card (3.3V) in this motherboard. It will burn and damage the
motherboard due to Intel® 845 chipset can not support AGP 2X (3.3V).
IMPORTANT! Before you plug-in AGP card, please make sure the following notice
is fully understood and practiced. If your AGP card has “AGP 4X notch (show below) please make sure your AGP card is AGP 4X (1.5V) not AGP 2X (3.3V)
14
AGP SLOT
Example 1: SiS 305 & ATi Rage 128 Pro AGP card those golden finger is compatible
with 2X/4X mode AGP slot, but only can support 2X (3.3V) only. If you install these cards in Intel® 845 based motherboard it will burn and damage the motherboard.
Example 2: We also find Dimanod Vipper V770 golden finger is design for 2X/4X
mode AGP Slot. It can be adjusted the jumper for AGP 2X (3.3V) or AGP 4X (1.5V). But the factory default setting is 2X (3.3V). If you install this AGP card in motherboard without change the jumper setting to 4X (1.5V), it will burn the motherboard.
2-6 Connectors, Headers
2-6-1 Connectors
(1) Power Connector (20-pin block) : ATXPWR
ATX Power Supply connector. This is a new defined 20-pins connector that usually
comes with ATX case. The ATX Power Supply allows to use soft power on momentary switch that connect from the front panel switch to 2-pins Power On jumper pole on the motherboard. When the power switch on the back of the ATX power supply turned on, the full power will not come into the system board until the front panel switch is momentarily pressed. Press this switch again will turn off the power to the system board.
PIN ROW2 ROW1
1 3.3V 3.3V 2 -12V 3.3V 3 GND GND 4 Soft Power On 5V 5 GND GND 6 GND 5V 7 GND GND 8 -5V Power OK 9 +5V +5V (for Soft Logic) 10 +5V +12V
Pin 1
(2) ATX 12V Power Connector (4-pin block) : ATX12V
2x notch 4x notch
15
This is a new defined 4-pins connector that usually comes with ATX Power Supply. The ATX Power Supply which fully support Pentium 4 processor must including this connector for support extra 12V voltage to maintain system power consumption. Without this connector might cause system unstable because the power supply can not provide sufficient current for system.
Pin 1
(3) ATX P9 Power Connector (6-pin block) : ATXP9
This is a new defined 6-pins connector that usually comes with ATX Power Supply. The ATX Power Supply which fully support Pentium 4 processor must including this connector for support extra 3.3V and 5V voltage to maintain system power consumption. Without this connector might cause system unstable because the power supply can not provide sufficient current for system.
Power Plugs from Power Supply Power Connector on Motherboard
BLK BLK BLK
ORG ORG
RED
GND GND
GND
3.3V
3.3V 5V
(4) PS/2 Mouse & PS/2 Keyboard Connector: PS2 KB/MOUSE
The connectors for PS/2 keyboard and PS/2 Mouse.
(5) USB Port connector: USB1
The connectors are 4-pin connector that connect USB devices to the system board.
(6) Parallel Port Connector (25-pin female): PRINT
Parallel Port connector is a 25-pin D-Subminiature Receptacle connector. The On­board Parallel Port can be disabled through the BIOS SETUP. Please refer to Chapter 3 “INTEGRATED PERIPHERALS SETUP” section for more detail information.
(7) Audio and Game Connector : AUD_GAME
This Connector are 3 phone Jack for LINE-OUT, LINE-IN, MIC and a 15-pin
16
D-Subminiature Receptacle Connector for joystick/MIDI Device.
Line-out :
Audio output to speaker
Line-in :
Audio input to sound chip
MIC :
Microphone Connector
Game/MIDI :
For joystick or MIDI Device
(8) Serial Port COM1, COM2 : COM1, COM2
COM1, COM2 are the 9-pin D-Subminiature mail connector. The On-board serial por t can b e disabled through BIOS SETUP. Please refer to Chapter 3 “INTEGRATED PERIPHERALS SETUP” se c t i o n f o r m o r e detail information.
(9) Floppy drive Connector (34-pin block): FDD
This connector supports the provided floppy drive ribbon cable. A fter connecting the single plug end to motherboard, connect the two plugs at other end to the floppy drives.
Pin 1
Flo
ppy
Drive Connector
(10) Primary IDE Connector (40-pin block): IDE1
This connector supports the provided IDE hard disk ribbon cable. After connecting
the single plug end to motherboard, connect the two plugs at other end to your hard disk(s). If you install two hard disks, you must configure the second drive to Slave mode by setting its jumpers accordingly. Please refer to the documentation of your hard disk for the jumper settings.
COM1 COM2
PS/2
MOUSE
PS/2
Keyboard
USB
LINE-OUT
LINE-IN
MIC
PRINT GAME/MIDI PORT
17
Primary IDE Connector
Pin 1
(11) Secondary IDE Connector (40-pin block): IDE2
This connector connects to the next set of Master and Slave hard disks. Follow the
same procedure described for the primary IDE connector. You may also configure two hard disks to be both Masters using one ribbon cable on the primary IDE connector and another ribbon cable on the secondary IDE connector.
Secondary IDE Connector
Pin 1
Two hard disks can be connected to each connector. The first HDD is referred to as the “Master” and the second HDD is referred to as the “Slave”.
For performance issues, we strongly suggest you don’t install a CD-ROM or DVD­ROM drive on the same IDE channel as a hard disk. Otherwise, the system performance on this channel may drop.
(12) IDE RAID Connectors : IDE3/IDE4 (Only for I401-R)
When JP14 setting 1-2 closed IDE3/IDE4 are setting in ATA 100 Mode for Normal extra IDE Interface. When JP14 setting 2-3 closed IDE3/IDE4 can setting RAID Mode for stripping capable to increase transfer rate, or RAID 1 Mode for mirroring capable for data protection. For more detail description please read PROMISE.DOC in CD-PACK X:\MANUAL\PROMISE.DOC file.
18
IDE RAID Connectors
Pin 1
Pin 1
IDE3
IDE4
2-6-2 Headers
(1) Line-In/Out, MIC Header (9-pin): AUDIO
This header connect to Front Panel Line-In, Line-out, MIC connector with cable.
Line-In/Out, MIC Headers
AUDIO
Pin 1
L-IN-L
L-OUT-L MIC
L-IN-R
L-OUT-R GND MICP
(2) USB Port Headers (9-pin) : USB2
These headers are used for connecting the additional USB port plug. By attaching an option USB cable, your can be provided with two additional USB plugs affixed to the back panel.
USB Port Headers
Pin 1
USB2
VCC
-
DATA
GND
+DATA
VCC
GND
-
DATA
GND
+DATA
19
(3) IDE Activity LED: IDE LED
This connector connects to the hard disk activity indicator light on the case.
(4) Turbo LED switch: TURBO LED
Since the motherboard’s turbo function is always on. The turbo LED will remain constantly on while the system power is on. You may wish to connect the Power LED from the system case to this lead. See the figure below.
(5) Reset switch lead: RESET
This 2-pin connector connects to the case-mounted reset switch for rebooting your computer without having to turn off your power switch. This is a preferred method of rebooting in order to prolong the lift of the system’s power supply. See the figure below.
(6)
Speaker connector: SPKR
This 4-pin connector connects to the case-mounted speaker. See the figure below.
(7) Power LED
: PWR-LED
The Power LED is light on while the system power is on. Connect the Power LED from the system case to this pin.
(8) Power switch
: PWR BTN
This 2-pin connector connects to the case-mounted power switch to power ON/OFF the system.
System Case Connections
GND
Turbo LED
GND
Reset SW
VCC
GND
Turbo SW/
Speaker
VCC
NC
GND
GND
Keyboard
Lock
Power LED
NC
GND
VCC
SMI
IDELED
PWR BTN
(9) Wake On-LAN/Modem Headers
(3-pin) : WOL, WOM
This connector connects to a LAN/Modem card with a WAKE ON-LAN/Modem output. This connector power up the system when a wake up signal is received through the LAN/Modem card.
NOTE: This feature requires that Wake On LAN or Ring In Wake up is enabled.
20
Wake-On-Modem Headers
WOM
5VSB
GND
WOM
Wake-On-LAN Headers
WOL
5VSB
GND
WON
(10) FAN Speed Headers (3-pin) : SYSFAN, SYSFAN2, CPUFAN
These connectors support cooling fans of 350mA (4.2 Watts) or less, depending on the fan manufacturer, the wire and plug may be different. The red wire should be positive, while the black should be ground. Connect the fan’s plug to the board taking into consideration the polarity of connector.
SYSFAN2
1
3
CPUFAN
1 3
SYSFAN
1 3
(11) IR infrared module Headers (5-pin) : IR
This connector supports the optional wireless transmitting and receiving infrared module. You must configure the setting through the BIOS setup to use the IR function.
21
Infrared Module Headers
IRRX
GND
IRTX
VCC
IR
1
5
(12) CD Audio-In Headers (4-pin) : CDIN
CDIN are the connectors for CD-Audio Input signal. Please connect it to CD-ROM CD-Audio output connector.
CD Audio-In Headers
CDIN
1
4
2-7 Starting Up Your Computer
1. After all connection are made, close your computer case cover.
2. Be sure all the switch are off, and check that the power supply input voltage is set to proper position, usually in-put voltage is 220V∼240V or 110V∼120V depending on your country’s voltage used.
3. Connect the power supply cord into the power supply located on the back of your system case according to your system user’s manual.
4. Turn on your peripheral as following order:
a. Your monitor. b. Other external peripheral (Printer, Scanner, External Modem etc…) c. Your system power. For ATX power supplies, you need to turn on the power supply
and press the ATX power switch on the front side of the case.
5. The power LED on the front panel of the system case will light. The LED on the monitor may light up or switch between orange and green after the system is on. If it complies with green standards or if it is has a power standby feature. The system will then run power-on test. While the test are running, the BIOS will alarm beeps or additional message will appear on the screen.
22
If you do not see any thing within 30 seconds from the time you turn on the power. The system may have failed on power-on test. Recheck your jumper settings and connections or call your retailer for assistance.
Beep Meaning
One short beep when displaying logo No error during POST Long beeps in an endless loop No DRAM install or detected One long beep followed by three short
beeps
Video card not found or video card memory bad
High frequency beeps when system is working
CPU overheated System running at a lower frequency
6.
During power-on, press <Delete> key to enter BIOS setup. Follow the instructions in BIOS SETUP.
7.
Power off your computer:
You must first exit or shut down your operating system before switch off the power switch. For ATX power supply, you can press ATX power switching after exiting or shutting down your operating system. If you use Windows 9X, click
“Start”
button, click
“Shut down”
and then click
“Shut down the computer?”
The power supply should turn off after windows shut down.
Chapter 3
Introducing BIOS
The BIOS is a program located on a Flash Memory on the motherboard. This program is a bridge between motherboard and operating system. When you start the computer, the BIOS program gain control. The BIOS first operates an auto-diagnostic test called POST (power on self test) for all the necessary hardware, it detects the entire hardware device and configures the parameters of the hardware synchronization. Only when these tasks are completed done it gives up control of the computer to operating system (OS). Since the BIOS is the only channel for hardware and software to communicate, it is the key factor for system stability, and in ensuring that your system performance as its best.
In the BIOS Setup main menu of Figure 3-1, you can see several options. We will explain these options step by step in the following pages of this chapter, but let us first see a short description of the function keys you may use here:
Press <Esc> to quit the BIOS Setup.
23
Press
↑↓←→
(up, down, left, right) to choose, in the main menu, the option you
want to confirm or to modify.
Press <F10> when you have completed the setup of BIOS parameters to save these
parameters and to exit the BIOS Setup menu.
Press Page Up/Page Down or +/– keys when you want to modify the BIOS
parameters for the active option.
3-1 Entering Setup
Power on the computer and by pressing <Del> immediately allows you to enter Setup. If the message disappears before your respond and you still wish to enter Setup, restart the system to try again by turning it OFF then ON or pressing the “RESET” button on the system case. You may also restart by simultaneously pressing <Ctrl>, <Alt> and <Delete> keys. If you do not press the keys at the correct time and the system does not boot, an error message will be displayed and you will again be asked to
Press <F1> to continue, <Ctrl-Alt-Esc> or <Del> to enter Setup
3-2 Getting Help
Main Menu
The on-line description of the highlighted setup function is displayed at the bottom of the screen.
Status Page Setup Menu/Option Page Setup Menu
Press F1 to pop up a small help window that describes the appropriate keys to use and the possible selections for the highlighted item. To exit the Help Window, press <Esc>.
3-3 The Main Menu
Once you enter Award BIOS CMOS Setup Utility, the Main Menu (Figure 3-1) will appear on the screen. The Main Menu allows you to select from fourteen setup functions and two exit choices. Use arrow keys to select among the items and press <Enter> to accept or enter the sub-menu.
24
CMOS Setup Utility – Copyright(C) 1984-2001 Award Software
Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Management Setup PnP/PCI Configurations PC Health Status
Miscellaneous Control Load optimized Defaults Load Standard Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving
Esc : Quit
↑↓→ ←
: Select Item
F10 : Save & Exit Setup
Time, Date, Hard Disk Type...
Figure 3-1
Standard CMOS Features
Use this Menu for basic system configurations.
Advanced BIOS Features
Use this menu to set the Advanced Features available on your system.
Advanced Chipset Features
Use this menu to change the values in the chipset registers and optimize your system’s performance.
Integrated Peripherals
Use this menu to specify your settings for integrated peripherals.
Power Management Setup
Use this menu to specify your settings for power management.
PnP/PCI configurations
This entry appears if your system supports PnP/PCI.
PC Health Status
This entry shows your PC health status.
Miscellaneous Control
Use this menu to specify your settings for Miscellaneous control.
Load Optimized Defaults
25
Use this menu to load the BIOS default values that are factory settings for optimal performances system operations.
Load Standard Defaults
Use this menu to load the BIOS default values for the minimal/stable performance system operation.
Set Supervisor/User Password
Use this menu to set User and Supervisor Passwords.
Save & Exit Setup
Save CMOS value changes to CMOS and exit setup.
Exit Without Saving
Abandon all CMOS value changes and exit setup.
3-4 Standard CMOS Features
The items in Standard CMOS Setup Menu are divided into several categories. Each category includes no, one or more than one setup items. Use the arrow keys to highlight the item and then use the <PgUp> or <PgDn> keys to select the value you want in each item.
CMOS Setup Utility – Copyright(C) 1984-2001 Award Software
Standard CMOS Features
Item Help
Date (mm:dd:yy) Thu, Jul, 05 2001 Time (hh:mm:ss) 11 : 33 : 50
> IDE Primary Master Press Enter None > IDE Primary Slave Press Enter None > IDE Secondary Master Press Enter None > IDE Secondary Slave Press Enter None
Drive A 1.44M, 3.25 in. Drive B None
Video EGA/VGA Halt On All,But Keyboard
Base Memory 640K Extended Memory 56320K Total Memory 57344K
Menu Level >
Change the day, month, year and century
↑↓→←
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Optimized Defaults F7:Standard Defaults
Date
26
The date format is <day><month><date><year>.
Day Day of the week, from Sun to Sat, determined by BIOS. Read-only. Month The month from Jan. through Dec. Date The date from 1 to 31 can be keyed by numeric function keys. Year The year depends on the year of the BIOS.
Time
The time format is <hour><minute><second>.
Primary Master/Primary Slave Secondary Master/Secondary Slave
Press PgUp/<+> or PgDn/<–> to select Manual, None, Auto type. Note that the specifications of your drive must match with the drive table. The hard disk will not work properly if you enter improper information for this category. If your hard disk drive type is not matched or listed, you can use Manual to define your own drive type manually.
If you select Manual, related information is asked to be entered to the following items. Enter the information directly from the keyboard. This information should be provided in the documentation from your hard disk vendor or the system manufacturer. If the controller of HDD interface is SCSI, the selection shall be “None”. If the controller of HDD interface is CD-ROM, the selection shall be “None”
Access Mode The settings are Auto Normal, Large, and LBA. Cylinder number of cylinders Head number of heads Precomp write precomp Landing Zone landing zone Sector number of sectors
3-5 Advanced BIOS Features
CMOS Setup Utility – Copyright(C) 1984-2001 Award Software
Advanced BIOS Features
Anti-Virus Protection Disabled Recovery Genius Enabled
Item Help
27
Hard Disk Boot Priority Press Enter CPU L1 &L2 Cache Enabled Quick Power On Self Test Enabled Hard Disk Boot Priority Press Enter First Boot Device Floppy Second Boot Device HDD-0 Third Boot Device CDROM Boot other Device Enabled Swap Floppy Drive Disabled Boot Up Floppy Seek Enabled Boot Up NumLock Status On Gate A20 Option Normal Typematic Rate Setting Disabled Typematic Rate (Chars/Sec) 6 Typematic Delay (Msec) 250 Security Option Setup APIC Mode Disabled MPS Version Control For OS 1.4 OS Select For DRAM > 64MB Non-OS2 HDD S.M.A.R.T. Capability Disabled
Menu Level >
↑↓→←
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Optimized Defaults F7:Standard Defaults
Anti-Virus Protection
Allows you to choose the VIRUS Warning feature for IDE Hard Disk boot sector protection. If this function is enabled and someone attempt to write data into this area, BIOS will show a warning message on screen and alarm beep.
Disabled (default) No warning message to appear when anything attempts to access the
boot sector or hard disk partition table.
Enabled Activates automatically when the system boots up causing a warning
message to appear when anything attempts to access the boot sector of hard disk partition table.
CPU Internal Cache
The default value is Enabled.
Enabled (default) Enable cache Disabled Disable cache
Note: The internal cache is built in the processor.
External Cache
Choose Enabled or Disabled. This option enables the Level 2 cache memory.
CPU L2 Cache ECC Checking
Choose Enabled or Disabled. This option enables the Level 2 cache memory ECC (error check correction).
Quick Power On Self-Test
This category speeds up Power On Self Test (POST) after you power on the computer. If this is set to Enabled. BIOS will shorten or skip some check items during POST.
Enabled (default) Enable quick POST Disabled Normal POST
28
First/Second/Third/Fourth Boot Device
The BIOS attempts to load the operating system from the devices in the sequence selected in these items. The settings are Floppy, LS/ZIP, HDD-0/HDD-1/HDD-3, SCSI, CDROM, LAD and Disabled.
Swap Floppy Drive
Switches the floppy disk drives between being designated as A and B. Default is Disabled.
Boot Up Floppy Seek
During POST, BIOS will determine if the floppy disk drive installed is 40 or 80 tracks. 360K type is 40 tracks while 760K, 1.2M and 1.44M are all 80 tracks.
Boot Up NumLock Status
The default value is On.
On (default) Keypad is numeric keys. Off Keypad is arrow keys.
Gate A20 Option
Normal The A20 signal is controlled by keyboard controller or chipset hardware. Fast (default) The A20 signal is controlled by port 92 or chipset specific method.
Typematic Rate Setting
Keystrokes repeat at a rate determined by the keyboard controller. When enabled, the typematic rate and typematic delay can be selected. The settings are: Enabled/Disabled.
Typematic Rate (Chars/Sec)
Sets the number of times a second to repeat a keystroke when you hold the key down. The settings are: 6, 8, 10, 12, 15, 20, 24, and 30.
Typematic Delay (Msec)
Sets the delay time after the key is held down before is begins to repeat the keystroke. The settings are 250, 500, 750, and 1000.
Security Option
This category allows you to limit access to the system and Setup, or just to Setup.
System The system will not boot and access to Setup will be denied if the
correct password is not entered at the prompt.
Setup (default) The system will boot, but access to Setup will be denied if the correct
password is not entered prompt.
OS Select For DRAM > 64MB
Allows OS2 to be used with >64MB or DRAM. Settings are Non-OS/2 (default) and OS2. Set to OS/2 if using more than 64MB and running OS/2
3-6 Advanced Chipset Features
The Advanced Chipset Features Setup option is used to change the values of the chipset registers. These registers control most of the system options in the computer.
29
CMOS Setup Utility – Copyright(C) 1984-2001 Award Software
Advanced Chipset Features
Item Help
> DRAM Timing Settings Press Enter System BIOS Cacheable Disabled Video RAM Cacheable Disabled Memory Hole At 15M-16M Disabled Delay Transaction Enabled AGP Aperture Size 64MB Delay Prior Thermal 16 Min
Menu Level >
↑↓→←
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Optimized Defaults F7:Standard Defaults
DRAM Timing Settings
Please refer to section 3-6-1
System BIOS Cacheable
Selecting Enabled allows caching of the system BIOS ROM at F0000h-FFFFFh, resulting in better system performance. However, if any program writes to this memory area, a system error may result. The settings are: Enabled and Disabled.
Video RAM Cacheable
Select Enabled allows caching of the video BIOS, resulting in better system performance. However, if any program writes to this memory area, a system error may result. The settings are: Enabled and Disabled.
Memory Hole At 15M-16M
You can reserve this area of system memory for ISA adapter ROM. When this area is reserved, it cannot be cached. The user information of peripherals that need to use this area of system memory usually discusses their memory requirements. The settings are: Enabled and Disabled.
Delay Transaction
The chipset has an embedded 32-bit posted write buffer to support delay transactions cycles. Select Enabled to support compliance with PCI specification version 2.1. The settings are: Enabled and Disabled.
3-6-1 DRAM Timing Settings
CMOS Setup Utility – Copyright(C) 1984-2001 Award Software
DRAM Timing Settings
SDRAM CAS Latency Time 3 SDRAM Cycle Time 6
Item Help
30
SDRAM RAS# to CAS# Delay 3 SDRAM RAS# Precharge 3 SDRAM Type Select PC133
Menu Level >>
↑↓→←
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Optimized Defaults F7:Standard Defaults
SDRAM RAS# To CAS# Delay
This field let’s you insert a timing delay between the CAS and RAS strobe signals, used when DRAM is written to, read from, or refreshed. Fast gives faster performance; and Slow gives more stable performance. This field applies only when synchronous DRAM is installed in the system. The settings are: Auto(Default), 2T and 3T.
SDRAM RAS# Precharge Time
If an insufficient number of cycles is allowed for the RAS to accumulate its charge before DRAM refresh, the refresh may be incomplete and the DRAM may fail to retain date. Fast gives faster performance; and Slow gives more stable performance. This field applies only when synchronous DRAM is installed in the system. The settings are: Auto (Default), 2T and 3T.
SDRAM CAS Latency Time
When synchronous DRAM is installed, the number of clock cycles of CAS latency depends on the DRAM timing. The settings are: Auto (Default), 2T and 3T.
Note: Change these settings only if you are familiar with the chipset.
3-7 Integrated Peripherals
CMOS Setup Utility – Copyright(C) 1984-2001 Award Software
Integrated Peripherals
Item Help
> Onboard IDE Function Press Enter > Onboard Device Function Press Enter > Onboard Super IO Function Press Enter Init Display First PCI Slot Power On Function Button Only KB Power On Password Enter Hot Key Power On Ctrl-F1 Power After Power Fail Always Off
Menu Level >
↑↓→←
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Optimized Defaults F7:Standard Defaults
Onboard IDE Function
Please refer to section 3-7-1
Onboard Device Function
Please refer to section 3-7-2
31
Onboard Super IO Function
Please refer to section 3-7-3
Init Display First
This item allows you to decide to activate whether PCI Slot or AGP VGA first. The settings are: PCI Slot, AGP Slot.
3-7-1 Onboard IDE Function
CMOS Setup Utility – Copyright(C) 1984-2001 Award Software
Onboard IDE Function
Item Help
OnChip IDE Channel0 Enabled OnChip IDE Channel1 Enabled Primary Master PIO Auto Primary Slave PIO Auto Secondary Master PIO Auto Secondary Slave PIO Auto Primary Master UDMA Auto Primary Slave UDMA Auto Secondary Master UDMA Auto Secondary Slave UDMA Auto IDE 32-bit Transfer Mode Enabled IDE HDD Block Mode Enabled IDE Prefetch Mode Enabled Delay For HDD (Secs) 0
Menu Level >>
↑↓→←
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Optimized Defaults F7:Standard Defaults
OnChip IDE Channal0/Channel1
The integrated peripheral controller contains an IDE interface with support for two IDE channels. Select Enabled to activate each channel separately. The settings are: Enabled and Disabled.
Primary/Secondary Master/Slave PIO
The four IDE PIO (Programmed Input/Output) fields let you set a PIO mode (0-4) for each of the four IDE devices that the onboard IDE interface supports. Modes 0 through 4 provide successively increased performance. In Auto mode, the system automatically determines the best mode for each device. The settings are: Auto, Mode 0, Mode 1, Mode 2, Mode 3, Mode 4.
Primary/Secondary Master/Slave UDMA
Ultra DMA/33 implementation is possible only if your IDE hard drive supports it and the operating environment includes a DMA driver (Windows 95 OSR2 or a third-party IDE bus master driver). If your hard drive and your system software both support Ultra DMA/33 and Ultra DMA/66, select Auto to enable BIOS support. The settings are: Auto, Disabled.
IDE HDD Block Mode
Block mode is also called block transfer, multiple commands, or multiple sector read/write. If your IDE hard drive supports block mode (most new drives do), select Enabled for
32
automatic detection of the optimal number of block read/writes per sector the drive can support. The settings are: Enabled, Disabled.
3-7-2 Onboard Device Function
CMOS Setup Utility – Copyright(C) 1984-2001 Award Software
Onboard Device Function
Item Help
USB Controller Enabled USB Keyboard Legacy Support Disabled **Onboard AC97 Codec is ALC201/201A ** AC97 Audio Auto AC97 Modem Auto Game Port Address 201 Midi Port Address 330 Midi Port IRQ 10
Menu Level >>
↑↓→←
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Optimized Defaults F7:Standard Defaults
AC97 Audio
This item allows you to decide to enable/disable the chipset family to support AC97 Audio. The settings are: Enabled, Disabled.
Game Port Address/Midi Port Address
This will determine which Address the Game Port/Midi Port will use.
AC97 Modem
This item allows you to decide to enable/disable the KT-266 chipset family to support AC97 Modem. The settings are: Auto, Disabled.
USB Controller
Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have a USB peripherals. The settings are: Enabled, Disabled.
USB Keyboard Legacy Support
Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have a USB keyboard. The settings are: Enabled, Disabled.
3-7-3 Onboard Super IO Function
33
CMOS Setup Utility – Copyright(C) 1984-2001 Award Software
Onboard Super IO Function
Item Help
Onboard FDD Controller Enabled Onboard Serial Port 1 3F8/IRQ4 Onboard Serial Port 2 2F8/IRQ3 UART2 Mode Normal RxD, TxD Active Hi, Lo IR Duplex Mode Half Use IR Pins IRRX/IRTX Onboard Parallel Port 378/IRQ7 Parallel Mode SPP EPP Mode Select EPP1.9 ECP Mode Use DMA 3
Menu Level >>
↑↓→←
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Optimized Defaults F7:Standard Defaults
Onboard FDD Controller
Select Enabled if your system has a floppy disk controller (FDD) installed on the system board and you wish to use it. If you install add-on FDC or the system has no floppy drive, select Disabled in this field. The settings are: Enabled and Disabled.
Onboard Serial Port 1/Port 2
Select an address and corresponding interrupt for the first and the second serial ports. The settings are: 3F8/IRQ4, 2E8/IRQ3, 3E8/IRQ4, 2F8/IRQ3, Disabled, Auto.
UART2 Mode
This item allows you to determine which InfraRed(IR) function of the onboard I/O chip, this functions uses.
Onboard Parallel Port
There is a built-in parallel port on the on-board Super I/O chipset that Provides Standard, ECP, and EPP features. It has the following option:
Disabled (3BCH/IRQ7)/ Line Printer port 0 (278H/IRQ5)/ Line Printer port 2 (378H/IRQ7) Line Printer port 1
Parallel Port Mode
SPP : Standard Parallel Port EPP : Enhanced Parallel Port ECP : Extended Capability Port
SPP/EPP/ECP/ECP+EPP
34
To operate the onboard parallel port as Standard Parallel Port only, choose “SPP.” To operate the onboard parallel port in the EPP modes simultaneously, choose “EPP.” By choosing “ECP”, the onboard parallel port will operate in ECP mode only. Choosing “ECP+EPP” will allow the onboard parallel port to support both the ECP and EPP modes simultaneously. The ECP mode has to use the DMA channel, so choose the onboard parallel port with the ECP feature. After selecting it, the following message will appear: “ECP Mode Use DMA” at this time, the user can choose between DMA channels 3 to 1. The onboard parallel port is EPP Spec. compliant, so after the user chooses the onboard parallel port with the EPP function, the following message will be displayed on the screen: “EPP Mode Select.” At this time either EPP 1.7 spec. or EPP
1.9 spec. can be chosen.
3-8 Power Management Setup
The Power Management Setup allows you to configure your system to most effectively save energy saving while operating in a manner consistent with your own style of computer use.
CMOS Setup Utility – Copyright(C) 1984-2001 Award Software
Power Management Setup
Item Help
ACPI Function Enabled ACPI Suspend Type S1(POS) Video Off Option Suspend -> off Video off Method V/H SYNC+Blank Video Off In Suspend Yes MODEM Use IRQ 3 HDD Power Down Disabled Soft-off by PWR-BTTN Instant-off Wake-Up by PCI card Disabled Power On by Ring Disabled Resume by Alarm Disabled X Date (of Month) 0 X Time (hh:mm:ss) 0 : 0 :0 CPU Thermal Management Timer 32 Min DRAM Read Thermal Management Disabled > PM Timer Reload Events Press Enter
Menu Level >
↑↓→←
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Optimized Defaults F7:Standard Defaults
ACPI Function
This item allows you to Enabled/Disabled the Advanced Configuration and Power Management (ACPI). The settings are Enabled and Disabled.
ACPI Suspend Type
This item allows you to select ACPI Suspend Type. The setting are: S1(POS), S3(STR)
Video Off in Suspend
35
This determines the manner in which the monitor is blanked. The choice are Yes Video will off , and No Video always On.
Video Off Method
This determines the manner in which the monitor is blanked.
DPMS (default) Initial display power management signaling. Blank Screen This option only writes blanks to the video buffer. V/H SYNC+Blank This selection will cause the system to turn off the vertical and
horizontal synchronization ports and write blanks to the video buffer.
Modem Use IRQ
This determines the IRQ in which the MODEM can use. The settings are: 3, 4, 5, 7, 9, 10, 11, NA.
Power Button Function
Pressing the power button for more than 4 seconds forces the system to enter the Soft-Off state. The settings are: Delay 4 Sec, Instant-Off.
Wake-Up by PCI card /Power On by Ring
During Disabled, the system will ignore any incoming call from the PCI card/modem. During Enabled, the system will boot up if there’s an incoming call from the PCI card /modem.
Wake-Up on RTC Alarm
This function is for setting date and time for your computer to boot up. During Disabled, you cannot use this function. During Enabled, choose the Date and Time Alarm:
Date(of month) Alarm
You can choose which month the system will boot up. Set to 0, to boot every day.
Time(hh:mm:ss) Alarm
You can choose what hour, minute and second the system will boot up.
Note: If you have change the setting, you must let the system boot up until it goes to the operating system, before this function will work
PM Timer Reload Events
Please refer to section 3-8-1
3-8-1 PM Timer Reload Events
36
CMOS Setup Utility – Copyright(C) 1984-2001 Award Software
PM Timer Reload Events
Item Help
Primary IDE 0 Disabled
Primary IDE 1 Disabled Secondary IDE 0 Disabled Secondary IDE 1 Disabled FDD, COM, LPT Port Disabled
PCI PIRQ [A-D] # Disabled
Menu Level >>
↑↓→←
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Optimized Defaults F7:Standard Defaults
3-9 PnP/PCI Configuration Setup
This section describes configuring the PCI bus system. PCI, or Personal Computer Interconnect, is a system which allows I/O devices to operate at speeds nearing the speed
the CPU itself uses when communicating with its own special components. This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings.
CMOS Setup Utility – Copyright(C) 1984-2001 Award Software
PnP/PCI Configurations
Item Help
Reset Configuration Data Disabled
Resources Controlled By Manual x IRQ Resources Press Enter
PCI/VGA Palette Snoop Disabled Assign IRQ For VGA Enabled
Menu Level >
↑↓→←
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Optimized Defaults F7:Standard Defaults
Reset Configuration Data
Normally, you leave this field Disabled. Select Enabled to reset Extended System Configuration
37
Data (ESCD) when you exit Setup if you have installed a new add-on and the system reconfiguration has caused such a serious conflict that the operating system can not boot. The settings are: Enabled and Disabled.
Resource Controlled By
The Award Plug and Play BIOS has the capacity to automatically configure all of the boot and Plug and Play compatible devices. However, this capability means absolutely nothing unless you are using a Plug and Play operating system such as Windows95/98. If you set this field to “manual” choose specific resources by going into each of the sub menu that follows this field (a sub menu is preceded by a “>”).
The settings are: Auto(ESCD), Manual.
IRQ Resources
When resources are controlled manually, assign each system interrupt a type, depending on the type of device using the interrupt.
Please refer to section 3-9-1
PCI/VGA Palette Snoop
Leave this field at Disabled. The settings are Enabled, Disabled.
3-9-1 IRQ Resources
CMOS Setup Utility – Copyright(C) 1984-2001 Award Software
IRQ Resources
Item Help
IRQ-3 assigned to PCI Device IRQ-4 assigned to PCI Device IRQ-5 assigned to PCI Device IRQ-7 assigned to PCI Device IRQ-9 assigned to PCI Device IRQ-10 assigned to PCI Device IRQ-11 assigned to PCI Device IRQ-12 assigned to PCI Device IRQ-14 assigned to PCI Device IRQ-15 assigned to PCI Device
Menu Level >>
↑↓→←
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Optimized Defaults F7:Standard Defaults
3-10 PC Health Status
38
This section shows the Status of you CPU, Fan, Warning for overall system status. This is only available if there is Hardware Monitor onboard.
CMOS Setup Utility – Copyright(C) 1984-2001 Award Software
PC Health Status
Item Help
Shutdown Temperature Disabled CPU Warning Temperature Disabled Show PC Health in Post Enabled Current System Temperature 25°C Current CPU Temperature 38°C Current CPUFAN Speed 5000 rpm Current SYSFAN Speed 5000 rpm Current SYSFAN2 Speed 5000 rpm Vcore 1.71V Vcc1.5 1.51V Vcc3.3 3.31V + 5V 4.98V +12V 12.22V
-12V -12.36V
- 5V VBAT(V) 3.21V 5VSB(V)
5.02V
Menu Level >
↑↓→←
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Optimized Defaults F7:Standard Defaults
Show PC Health in Post
During Enabled, it displays information list below. The choice is either Enabled or Disabled.
Current CPU Temperature/Current System Temp/Current FAN1, FAN2 Speed/Vcore/ Vdd/3.3V/+5V/+12V/-12V/VBAT(V)/5VSB(V)
This will show the CPU/FAN/System voltage chart and FAN Speed.
Shutdown Temperature
This item can let users setting the Shutdown temperature, when CPU temperature over this setting the system will auto shutdown to protect CPU.
3-11 Miscellaneous Control
39
This section is for setting CPU Frequency/Voltage Control.
CMOS Setup Utility – Copyright(C) 1984-2001 Award Software
Miscellaneous Control
Item Help
CPU Clock Ratio X 8 Auto Detect PCI Clk Enabled Spread Spectrum Disabled CPU Clock 100MHz CPU Vcore Select Default Vcc1.5 Select 1.5V VDIMM Select 3.30V Flash Part Write Protect Enabled
Menu Level >
↑↓→←
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5:Previous Values F6:Optimized Defaults F7:Standard Defaults
Auto Detect PCI Clk
This item allows you to enable/disable auto detect PCI Clock. The settings are: Enabled, Disabled.
Spread Spectrum
This item allows you to set the CPU Host/PCI clock and Spread Spectrum. The settings are: Enabled, Disabled.
CPU Clock
This item allows you to select CPU frequency step by step increasing The choice are: 100MHz∼133MHz
CPU Vcore Select
This item allows you to select Vcore of the CPU. The choice are: +1.650V∼+1.850V.
Vcc1.5 Select
This item allows you to select 1.5V of the AGP VGA card. The choice are: Default, 1.5V,
1.6V.
VDIMM Select
This item allows you to select 2.5V of the DDR Module. The choice are: 3.30V~3.66V
Flash Part Write Protect
This item allow you protect your BIOS chip from Virus destroy data. When Flash BIOS you have Disabled this item
3-12 Load Standard/Optimized Defaults
Load Standard Defaults
40
When you press <Enter> on this item, you get confirmation dialog box with a message similar to:
Load Standard Defaults (Y/N)? N
Pressing <Y> loads the BIOS default values for the most stable, minimal-performance system operations.
Load Optimized Defaults
When you press <Enter> on this item, you get a confirmation dialog box with a message similar to:
Load Optimized Defaults (Y/N)? N
Pressing <Y> loads the default values that are factory settings for optimal performance system operations.
3-13 Set Supervisor/User Password
You can set either supervisor or user password, or both of them. The differences are:
Supervisor password: Can enter and change the options of the setup menus. User password: Can only enter but do not have the right to change the options of
the setup menus. When you select this function, the following message will appear at the center of the screen to assist you in creating a password.
ENTER PASSWORD:
Type the password, up to eight characters in length, and press <Enter>. The password typed now will clear any previously entered password from CMOS memory. You will be asked to confirm the password. Type the password again and press <Enter>. You may also press <Esc> to abort the selection and not enter a password.
To disable a password, just press <Enter> when you are prompted to enter the password. A message will confirm that the password will be disabled. Once the password is disabled, the system will boot and you can enter Setup freely.
PASSWORD DISABLED.
When a password has been enabled, you will be prompted to enter it every time you try to enter Setup. This prevents an unauthorized person from changing any part of your system configuration.
Additionally, when a password is enabled, you can also require the BIOS to request a password every time your system is rebooted. This would prevent unauthorized use of your computer.
You determine when the password is required within the BIOS Features Setup Menu and its Security option. If the Security option is set to “System”, the password will be required both at boot and at entry to Setup. If set to “Setup”, prompting only occurs when trying to enter Setup.
Chapter 4
DRIVER & FREE PROGRAM INSTALLATION
41
Check your package and there is A MAGIC INSTALL CD included. This CD consists of all DRIVERS you need and some free application programs and utility programs. In addition, this CD also include an auto detect software which can tell you which hardware is installed, and which DRIVERS needed so that your system can function properly. We call this auto detect software MAGIC INSTALL.
MAGIC INSTALL Supports WINDOWS 95/98/98SE/ME/NT4.0/2000
Insert CD into your CD-ROM drive and the MAGIC INSTALL Menu should appear as below. If the menu does not appear, double-click MY COMPUTER / double-click CD­ROM drive or click START / click RUN / type X:\SETUP.EXE (assuming X is your CD­ROM drive).
From MAGIC INSTALL MENU you may make 12 selections:
1. INF install Intel 845 chipset system driver
2. IDE install Intel 845 Ultra ATA driver
3. SOUND install ALC201 Audio Codec driver
4. PROMISE RAID install Promise RAID Controller driver (for I401-R only)
5. RAID UTILITY install Promise RAID Controller Utility (for I401-R only)
6. ATA100 install Promise ATA 100 Controller driver (for I401-R only)
7. PC-HEALTH install Intel 845 PC-HEALTH monitor
8. MAGIC BIOS install BIOS Live Update Utility
9. PC-CILLIN install PC-CILLIN2000 anti-virus program
10. DIRECTX8 install Microsoft DirectX 8.0 driver
11. BROWSE CD to browse the contents of the CD
12. EXIT to exit from MAGIC INSTALL menu
4-1 INF install INTEL 845 chipset system driver
After you have completed the installation of your operation system (WINDOWS 95/98/ 98SE). You will find an UNKNOWN DEVICE in the device manager (START/SETTING/
42
CONTROL PANEL/SYSTEM/DEVICE MANAGER). You have to install INF driver as shown below:
1. Click INF in the MAGIC INSTALL MENU 2. Click NEXT when Chipset Software Install Utility appears
3. This chart shows motherboards supported
by the driver click Yes
4. Select if you want computer re-started click Finish
NOTE: MAGIC INSTALL will auto detect file path X:\INTEL845\INF\SETUP.EXE This driver supports WINDOWS 95/98/98SE/ME/2000 (NT4.0 do not require)
4-2 IDE install Intel 845 Ultra ATA driver
43
1. Click IDE when MAGIC INSTALL MENU appears
2. Click NEXT when INTEL Application Setup Wizard appears
3. This is to announce the Copy Right click Yes
4. Click NEXT or BROWSE to change the path you want the driver stored
5. Select Program Group Name or Enter a new Group Name and Click Next
6. Click Finish, if you want to re-start your computer
NOTE: MAGIC INSTALL will auto detect file path X:\INTEL845\IDE\SETUP.EXE This driver supports WINDOWS 95/98/98SE/ME/NT4.0/2000
4-3 SOUND Install ALC201 Audio Codec Driver
44
1. Click SOUND when MAGIC INSTALL MENU appears
2. Then auto detect operation system language edition, click Next, start to install DRIVER
3. Click Finish and Restart Windows
4. Click Start→Program→Avance Sound
Manager→AvRack. Then AVRACK Windows appears
5. Avance Audio Rack table can play CD, WAV, MID, MP3, AVI, MPG Format File
6. This is a Sound Environment Simulator and Karaok function table
NOTE: MAGIC INSTALL will auto detect file path:
X:\CODEC\ALC201\SETUP.EXE (for WINDOWS 95/98/98SE/ME/NT4.0/2000)
4-4 PROMISE ATA100/RAID Manual (Only for I401-R)
45
(Read CD-PACK X:\MANUAL\PROMISE.DOC to get more information)
4-4-1 Install PROMISE ATA100 IDE Controller Driver
When the Jumper setting ATA100 you will have next screen in Magic Install MENU.
1. Click PROMISE ATA100 Controller Driver in MAGIC INSTALL MENU
2. Install PROMISE ATA100 Controller Driver
3. Click Yes to Restart your computer after Driver Install Finish
NOTE: The path of the file:
For Windows 95/98 is X:\PORMISE\ATA100\WIN95-98 (including Win95/98) For Windows ME is X:\PORMISE\ATA100\WINME For Windows 2000 is X:\PORMISE\ATA100\WIN2000 For Windows NT4.0 is X:\PORMISE\ATA100\NT4
4-4-2 Install PROMISE IDE RAID Controller Driver
When the Jumper setting in RAID Mode you will have next screen in Magic Install MENU.
46
1. Click PROMISE RAID Controller Driver when MAGIC INSTALL MENU
2. Install PROMISE RAID Controller Driver
3. Click Yes to Restart your computer after Driver Install Finish
4-4-3 Install PROMISE IDE RAID Controller Utility
1. Click PROMISE RAID Controller Utility in MAGIC INSTALL MENU
2. In this screen please click Next to install PROMISE Monitoring Utility
NOTE: The path of the file:
For Windows 9X is X:\PORMISE\RAID\WIN9X-ME (including Win95/98/ME)
For Windows NT4.0 is X:\PORMISE\RAID\NT4
For Windows 2000 is X:\PORMISE\RAID\WIN2000
For Novell Netware is X:\PORMISE\RAID\NETWARE
47
3. Click Next to continue Setup PROMISE FastTrak Controller Utility
4. Select the components you want to install and click Next to Setup
5. Select Yes if you want the FastCheck Monitoring Utility automatically run after windows starts
6. Click Finish after complete Setup
7. After Windows restart click FastCheck Monitoring Utility you can monitor the RAID Status
The path of the file: X:\PORMISE\UTILITY\SETUP (For Windows 95/98/98SE/ME/NT4.0/2000)
For detail information please read PROMISE.DOC in CD-PACK X:\MANUAL\PROMISE.DOC
48
4-5 PC-HEALTH Winbond Hardware Doctor Monitoring Software
The path of the file is X:\INTEL845\HW30\SETUP.EXE (Only support WINDOWS 95/98/98SE/ME)
In Windows 95/98 Winbond Hardware Doctor Monitoring Software needs some system files to copy in Utility that’s why it needs install PC-HEALTH twice to complete setup.
1. Click PC-Health when Magic Install
Menu appears
2. Click Next when Winbond Hardware Doctor Setup Window appears
3. Click Next to continue installation 4. Select Program Group name or enter a new group name, click Next, and click Finish after setup complete
49
4-5-1 How To Utilize PC-HEALTH
1. Click Program → Winbond Hardware
Doctor → Hardware Doctor the Winbond Hardware Doctor will appears
You can remove the Utility in Control Panel → Add/Remove Program icon
2. After executing Winbond Hardware Doctor it supports system voltage, Fan speed and CPU/SYSTEM Temperature. Because this is a On-time Monitoring program therefore the value will change after it detected, if the value is over default setting the system will have warning picture and beeps. This is a System Voltage status
3. This is a CPU/System Fan Speed and Temperature status information
4. This is a CPU and System Memory status information
50
4-6 MAGIC BIOS Install BIOS Live Update Utility
1. Click Magic BIOS when Magic Install MENU appears
2. Click Next to install the Magic BIOS in Destination Folder
3. After finish Setup you will have a Magic BIOS icon in your screen
4. Double click the Magic BIOS icon you will have this picture, choose from internet you can upgrade BIOS On-line
5. When On-line update BIOS the program will auto-check your BIOS version
6. Click Next if you need update BIOS, after upgrade BIOS, the system will clear CMOS and automatically restart
51
7. Click Yes if you want to update the BIOS otherwise choose No to exit
8. When System programming BIOS don’t turn off power, after finish update BIOS, the system will clear CMOS and automatically Restart
9. When choose From Local Driver to update BIOS, you must have the correct BIOS file in your Local Driver
10. Choose the correct BIOS file to update BIOS
52
4-7 PC-CILLIN Install PC-CILLIN 2000 Anti-virus program
1. Click PC-CILLIN when MAGIC INSTALL MENU Appears
2. Click NEXT when PC-CILIN 2000 SETUP APPEARS. Then click YES when the announcement of copywrite appears. Software is starting to detect HD for virus
3. Click NEXT and Enter User Information, Click NEXT or choose BROWSE to change the path For the file to be stored
4. Click NEXT and Choose all Internet Protection
5. Click OK and If You Have Proxy Server, Enter Your Setting
6. Click NEXT when Start Copy Files, Start to install the software
53
7. If you want to make a rescue disc, insert a
1.44 MB disc
8. Setup Complete and click Finish
9. Enter Your name and E-mail address Register PC-cillin 2000 or Click Cancel Register Later
10. After install PC-cillin 2000 complete we recommend select update item to download newest virus code and setting Auto refresh virus code
54
4-8 HOW TO DISABLE ON-BOARD SOUND
Enter BIOS SETUP choose INTEGRATE PERIPHERALS choose ON-CHIP DEVICE FUNCTION choose AC97 SOUND DEVICE Disable on-board sound function by press PAGE DOWN KEY to Disable
4-9 HOW TO UPDATE BIOS
Before update BIOS users have to “Disable”, “Flash Part Write Protect” item which in “Miscellaneous Control” of BIOS SETUP. Otherwise the system the will not allow you to upgrade BIOS by Award Flash Utility.
Method 1.
Use “Magic BIOS” update BIOS in Windows 98 (refer page 49)
Method 2.
In DOS Mode
STEP 1.
Prepare a boot disc. (you may make one by click START click RUN type SYS A:
click OK)
STEP 2.
Copy utility program to your boot disc. You may copy from DRIVER CD
X:\FLASH\AWDFLASH.EXE or download from our web site.
STEP 3.
Copy latest BIOS for I401-R/I401 from our web site to your boot disc.
STEP 4.
Insert your boot disc into A:, start the computer, type “Awdflash A:\I401Axxx.BIN /SN/PY/CC/R” I401Axxx.BIN is the file name of latest BIOS it can be I401A03.BIN or
I401B02.BIN SN means don’t save existing BIOS data PY means renew existing BIOS data CC means clear existing CMOS data R means restart computer
STEP 5. Push ENTER and the BIOS will be updated, computer will be restarted
automatically
Loading...