Page 1
TECHNICAL MANUAL
Of
Intel Cedar Trail-D & NM10 Chipset
Based
Mini-ITX M/B for ATOM Processor
NO.
G03-NF9D-F
Revi
sion: 2.0
Release date:
March 20, 2012
Trademark:
* Specifications and Information contained in this docume ntation ar e furnishe d for inf ormation us e only , and a re
subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
Page 2
i
Environmental Protection Announcement
Do not dispose this electronic device into the trash while discarding. To minimize
pollution and ensure environment protection of mother earth, please recycle.
Page 3
ii
ENVIRONMENTAL SAFETY INSTRUCTION...........................................................................iii
USER’S NOTICE .......................................................................................................................iv
MANUAL REVISION INFORMATION.......................................................................................iv
ITEM CHECKLIST.....................................................................................................................iv
CHAPTER 1 INTRODUCTION OF THE MOTHERBOARD
1-1 FEATURE OF MOTHERBOARD................................................................................1
1-2 SPECIFICATION.........................................................................................................2
1-3 LAYOUT DIAGRAM....................................................................................................3
CHAPTER 2 HARDWARE INSTALLATION
2-1 JUMPER SETTING.....................................................................................................6
2-2 CONNECTORS AND HEADERS................................................................................11
2-2-1 CONNECTORS .............................................................................................11
2-2-2 HEADERS .....................................................................................................12
CHAPTER 3 INTRODUCING BIOS
3-1 ENTERNING SETUP...................................................................................................20
3-2 BIOS MENU SCREEN ................................................................................................20
3-3 FUNCTION KEYS .......................................................................................................21
3-4 GETTING HELP ..........................................................................................................22
3-5 MENU BAR..................................................................................................................22
3-6 MAIN MENU................................................................................................................23
3-7 ADVANCED MENU.....................................................................................................24
3-8 CHIPSET MENU..........................................................................................................30
3-9 BOOT MENU...............................................................................................................32
3-10 SECURITY MENU.......................................................................................................33
3-11 SAVE & EXIT MENU...................................................................................................34
TABLE OF CONTENT
Page 4
iii
Environmental Safety Instruction
z Avoid the dusty, humidity and temperature extremes. Do not place the product in
any area where it may become wet.
z 0 to 60 centigrade is the suitable temperature. (The figure comes from the request
of the main chipset)
z Generally speaking, dramatic changes in temperature may lead to contact
malfunction and crackles due to constant thermal expansion and contraction from
the welding spots’ that connect components and PCB. Computer should go
through an adaptive phase before it boots when it is moved from a cold
environment to a warmer one to avoid condensation phenomenon. These water
drops attached on PCB or the surface of the components can bring about
phenomena as minor as computer instability resulted from corrosion and oxidation
from components and PCB or as major as short circuit that can burn the
components. Suggest starting the computer until the temperature goes up.
z The increasing temperature of the capacitor may decrease the life of computer.
Using the close case may decrease the life of other device because the higher
temperature in the inner of the case.
z Attention to the heat sink when you over-clocking. The higher temperature may
decrease the life of the device and burned the capacitor.
Page 5
iv
USER’S NOTICE
COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL,
INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED, TRANSMITTED
OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT WRITTEN
PERMISSION OF THE MANUFACTURER.
THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE THIS MOTHER-BOARD SERIES AN D WE
DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT WILL CHANGE, CORRECT ANY TIME
WITHOUT NOTICE. MANUFACTURER PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY
KIND, AND WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFIT, LOSS OF BUSINESS, LOSS OF USE OF DATA,
INTERRUPTION OF BUSINESS AND THE LIKE).
PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE
REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES, AND THEY ARE
USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER’S BENEFIT, WITHOUT
INTENT TO INFRINGE.
Manual Revision Information
Reversion Revision History Date
1.0 First Edition January 12, 2012
Item Checklist
5
Motherboard
5
User’s Manual
5
DVD for motherboard utilities
5
Cable(s)
5
I/O Back panel shield
Page 6
1
Chapter 1
Introduction of the Motherboard
1-1 Feature of Motherboard
z
Intel Cedar Trail-D and NM10 chipset, with low power consumption never denies
high performance
z
Support two DDRIII 800/1066MHz SO-DIMM up to 4GB
z
Support 2 * Serial ATAII (3Gb/s) Devices and 2 * Serial ATAIII (6Gb/s) Devices
z
Onboard dual Realtek RTL 8111EVL Gigabit Ethernet LAN chip
z
Integrated ALC662-GR 6-channel HD audio CODEC
z
Support USB 2.0 data transport demands
z
Support PCI slot and mini-PCIE slot
z
Support daughter board expansion
z
Support Watchdog function
z
Support Smart Fan function
z
Compliance with ErP standard
Page 7
2
1-2 Specification
Spec Description
Design z
Mini-ITX form factor; PCB size: 17.0x17.0cm
Chipset
z
Intel®NM10 Express chipset
Embedded CPU
z
Intel Cedar Trail-D Processor
Memory Slot
z
DDRIII SO-DIMM slot x 2
z
Support two DDRIII 800/1066 MHz SO-DIMM with memory
capacity expandable to 4GB
Expansion Slot
z
32-bit PCI slot x 1
z
Mini-PCIE slot x1
Dual LAN Chip
z
Integrated with two Realtek RTL8111EVL PCI-E Gigabit
LAN chips
z
Support Fast Ethernet LAN function of providing
10/100/1000Mbps Ethernet data transfer rate
Audio Chip
z
Realtek ALC662-GR 6-channel Audio Codec integrated
z
Audio driver and utility included
BIOS z
AMI 16MB DIP Flash ROM
Multi I/O
z
PS/2 keyboard/ mouse combo connector x1
z
VGA port connector x1
z
Serial port connector x 1
z
USB 2.0 port connector x4
z
RJ-45 LAN connector x2
z
HDMI port connector x1
z
Audio connector x3 (Line-in, Line-out, MIC)
z
SATAII port connector x2
z
SATAIII port connector x2
z
Front panel audio header x1
z
CDIN header x 1
z
HDMI_SPDIF header x1
z
Serial port header x1
z
RS232/422/RS485 header x1
z
4-pin USB 2.0 header x1
Page 8
3
z
9-pin USB 2.0 header x1
z
GPIO header x1
z
LVDS inverter x1
z
24- bit single channel LVDS header x1
z
PWRLED header x1
z
Speaker header x1
z
Front panel header x1
z
Parallel header x1
z
Jetway daughter board header x 2
1-3 Layout Diagram
MIC-IN
VGA Port
Line-OUT
Line-IN
RJ-45 LAN Port
PS/2 Keyboard &
Mouse Combo Port
HDMI Port
Serial Port
RJ-45 LAN Port
USB 2.0 Ports
Page 9
4
ATX Power
Connector
SYSFAN Heade
r
USB 2.0 Heade
r
Line-In
PS/2 KB & MS Combo
Port over USB 2.0 Ports
HDMI Port
RJ-45 LAN Port over
USB 2.0 Ports
Front Panel
Audio Header
PCI Slot
Power
LED Header
CPUFAN Header
RJ-45 LAN Port
LVDS Inverter
LVDS Heade
r
Parallel Port
Header
Serial Por
t
Heade
r
SATAII Ports
(SATA1/SATA2)
Front Panel Header
Speaker Header
Intel CPU
Intel NM10 Chipset
HDMI_SPDIF
Header
J
P1
J
P2
COPE
N
SODIMM2 Slot
Serial Port
over
VGA Port
Line-Out
MIC-In
CDIN Header
GPIO Heade
r
SYSFAN Heade
r
Mini-PCIE Slo
t
J
P3
JP5JP6J
BAT
JP7J
P8
SODIMM1 Slot
SATAIII Ports
(SATA3/SATA4)
Jetway Daughter Board Connectors
TX-RX COM Header
Page 10
5
Jumper
Jumper Name Description
JBAT CMOS RAM Clear Function Setting 3-pin Block
JP1 K/B, USB Power On Function Setting 3-pin Block
JP2 LVDS PVCC 5V/3.3V Select 3-pin Block
JP3 Inverter12V/5V Select 3-pin Block
JP5 USB 2/3 Header Power On Function Setting 3-pin Block
JP6 MINIPCIE Power SB 3.3V/3.3V Select 3-pin Block
JP7 COM2 RS232 Power Select 6-pin Block
JP8 COM2 RS232/422/485 Function Select 6-pin Block
Connectors
Connector Name Description
ATXPWR1 ATX Power Connector 24-pin Connector
KB & MS combined
connector from UK1
PS2 Keyboard & Mouse Connector 6-pin Female
VGA Video Graphic Attach Connector 15-pin Female
COM1 Serial Port Connector 9-pin Connector
HDMI High-Definition Multimedia Interface 10-pin Connector
USB from UK1,UL1 USB Port Connector 4-pin Connector
LAN from LAN1, UL1 RJ-45 LAN Connector 8-pin Connector
AUDIO Line-in/Line-out/MIC 3-phone Jack
SATA1,2 Serial ATAII Connector 7-pin Connector
SATA3/SATA4 Serial ATAIII Connector 7-Pin Connector
Headers
Header Name Description
FP-AUDIO1 Front Panel Audio Header 9-pin block
CDIN1 CD Audio-In Header 4-pin block
SPDIF SPDIF Out header 2-pin block
USB2 USB 2.0 Header 4-pin Block
USB3 USB 2.0 Header 9-pin Block
GPIO_CON GPIO Header 10-pin Block
Page 11
6
COM2 Serial Port Header 9-pin Block
TX_RX COM RS 232/422/485 port headers 4-pin block
PWR LED Power LED 3-pin Block
SPEAK Speaker Header 4-pin Block
JW_FP
Front Panel Header(PWR LED/
HD LED/ /Power Button /Reset)
9-pin Block
LVDS LVDS Header 32-pin Block
INVERTER LVDS Inverter Connector 7-pin Block
CPUFAN,SYSFAN1/2 FAN Speed Headers 3-pin Block
PARALLEL Parallel Port Header 25-pin Block
CN1; CN2 Jetway Daughter Card Connector 50-pin *2 Block
Chapter 2
Hardware Installation
2-1 Jumper Setting
(1) JBAT (3-pin): Clear CMOS
2-3 closed : Clear CMOS
JBATJBAT
1
3
1-2 closed: Normal;
1
3
Page 12
7
(2) JP1 (3-pin): K/B, USB Power on Function Setting
2-3 closed:K/B, USB Power-On Enabled
JP1
JP1
1-2 Clos ed: K/B, USB Power-On Disable d (default)
13
1
3
(3) JP2 (3-pin): LVDS PVCC 5V/3.3V Select
2-3 C osed : LVDS VCC=3.3V
JP2JP2
1-2 Closed: LVDS VCC= 5V;
3
3 1
1
Page 13
8
(4) JP3 (3-pin): Inverter VCC 5V/12V select
2-3 Cl ose d : Inverter 5V Select
JP3JP3
1-2 Closed: Inverter 12V Select;
3
1
3
1
(5) JP5 (3-pin): USB2/3 Header Power on Function Setting
2-3 Closed: USB 2/3 Header Power-On Enabled
JP5
JP5
1-2 Closed : USB 2/3 Header Power-On Disabled(default)
Page 14
9
(6) JP6(3-pin): Mini PCI-E Power VCC3.3V/ 3.3 V SB Select
2-3 Closed ： MI N I PCI -E VCC= 3.3 VS B Sel ect
JP6
1-2 Closed ： MINI PCI-E VCC= 3.3V Select；
3
13
JP6
(7) JP7 (6-pin): COM2 Pin9 Function Select
3-4 Closed : +12V;
JP7
1
1-2 Closed: RS232;
1
1
5-6 Closed : +5V
Page 15
10
(8) JP8 (6-pin): COM2 Port RS232/485/422 Function Select
3-4 Closed : RS485;
JP8
1
1-2 Closed: RS232;
11
5-6 Cl o se d : RS 42 2
(9)COPEN (2-pin): Case Open Message Display Function Select
Case Open Displa y Function
1-2 Short ： Case Open
COPEN
1-2 Open： Normal
Pin 1-2 shorted: Case open display function enabled. In this case if you case is
removed, next time when you restart your computer a message will be displayed
onscreen to inform you of this.
Page 16
11
2-2 Connectors and Headers
2-2-1 Connectors
(1) I/O Panel Connector:
(2) Serial-ATA Port connector: SATA1, SATA2, SATA3, SATA4
SATA1 and SATA2 connectors are SATAII connectors that support SATA 3Gb/s
specification. SATA3 and SATA4 connectors are SATAIII connectors that
support SATA 6Gb/s specification.
Pin No. Defi n it i on
1 GND
2 TXP
3 TXN
4 GND
5 RXN
6 RXP
7 GND
MIC-IN
VGA Port
Line-OUT
Line-IN
RJ-45 LAN Port
PS/2 Keyboard &
Mouse Combo Port
HDMI Port
Serial Port
RJ-45 LAN Port
USB 2.0 Ports
Page 17
12
(3) Power Connector (24-pin block): ATXPWR
2-2-2 Headers
(1) Front Panel Audio Header (9-pin): FP_AUDIO1
This header connects to front panel Line-out, MIC-In connector with cable.
Li ne -Out, MIC H e ad er
AUDIO
Pin 1
Lineout2-L
Lineout2-R
Sense-FB
Audio-GND
LINE2
Audio
2
9
10
KEY
MIC2-L
MIC2
MIC2-R
Page 18
13
(2) CD AUDIO-In Header (4-pin): CDIN
GND
CD-R
CD-L
GND
Pin1
(3) HDMI-SPDIF Out header (2-pin): SPDIF
HDMI_SPDIF Header
1
GND
2
HDMI_SPDIF_OUT
Page 19
14
(4) USB 2.0 Port Header (4-pin): USB2
USB2 Header
Pin 1
VCC
-DATA
GND
+DATA
(5) USB 2.0 Port Header (9-pin): USB3
VCC
Pin 1
-DATA
GND
+DAT A
VCC
NC
-DATA
GND
+DATA
Page 20
15
(6) COM2 (9-pin): RS232 Header
Serial COM Port 9-pin Block
Pin1
Pin6
DCD
Pin5
DSR
RXD
TXD
DTR
GND
RTS
CTS
RI
(7) TX-RXCOM (4-pin): RS422/485 Header
TX-RXCOM Header
Pin 1
TXDN
RXDP
TXDP
2
RXDN
(8) Speaker Header (4-pin): SPEAK
This 4-pin connector connects to the case-mounted speaker. See the figure below.
(9) Power LED (3-pin): PWR LED
The Power LED is light on while the system power is on. Connect the Power LED
from the system case to this pin header.
Page 21
1
6
SPEAK
SPEAK
NC
NC
VCC
Pin 1
PWRLED
Pin 1
VCC
GND
GND
(10) Front Panel Header (9-pin): JW-FP
HDLED
RESET
HDDLED+
GND
PWRLED+
PWR LED
PWRBTN
PWRBTN
PWRLED-
HDDLED-
RSTSW
NC
GND
JW F P
Pin 1
(11) FAN Speed Headers (3-pin): CPUFAN, SYSFAN1,SYSFAN2
Pin1: GND
Pin2: +12V fan power
Pin3: Fan Speed
Page 22
1
7
SYSFA N
1
3
1
3
CPUFAN
SYSFAN2
1
3
(12) LVDS Inverter (7-Pin): INVERTER
Pin 1
INVERTER
Pin No. Defi n it i on
1 VCC
2 VCC
3 GND
4 GND
5 Backlight
6 GND
7 Brightness
Page 23
18
(13)24-bit LVDS Header (32-pin): LVDS
Pin 1
LVDS Header
Pin 2
Pin NO. Pin Definition Pin NO. Pin Definition
Pin 1
NC
Pin 2
NC
Pin 3
NC
Pin 4
NC
Pin 5
NC
Pin 6
NC
Pin 7
NC
Pin 8
NC
Pin 9
NC
Pin 10
NC
Pin 11
LVDS_DDC_DATA
Pin 12
LVDS_DDC_CLK
Pin 13
GND
Pin 14
GND
Pin 15
GND
Pin 16
GND
Pin 17
LVDSA_DATAP3
Pin 18
LVDSA_DATAN3
Pin 19
LVDS_CLKAP
Pin 20 LVDS_CLKAN
Pin 21
LVDSA_DATAP2
Pin 22 LVDSA_DATAN2
Pin 23
LVDSA_DATAP1
Pin 24 LVDSA_DATAN1
Pin 25
LVDSA_DATAP0
Pin 26 LVDSA_DATAN0
Pin 27
PVDD
Pin 28 PVDD
Pin 29
PVDD
Pin 30 PVDD
Pin 31
GND
Pin 32 GND
Page 24
19
(14) GPIO Header (10-pin): GPIO_CON
GPIO_C ON Header
9
GPIO_10
GND
GPIO_11
GPIO_12
GPIO_13
GPIO_
6
4
GPIO_16
GPIO
_
6
3
2
Pin 1
10
GPIO_17
VCC
Page 25
20
Chapter 3
Introducing BIOS
Notice!
The BIOS options in this manual are for reference only. Different
configurations may lead to difference in BIOS screen and BIOS
screens in manuals are usually the first BIOS version when the board is
released and may be different from your purchased motherboard.
Users are welcome to download the latest BIOS version form our
official website.
The BIOS is a program located on a Flash Memory on the motherboard. This program
is a bridge between motherboard and operating system. When you start the computer,
the BIOS program will gain control. The BIOS first operates an auto-diagnostic test
called POST (power on self test) for all the necessary hardware, it detects the entire
hardware device and configures the parameters of the hardware synchronization.
Only when these tasks are completed done it gives up control of the computer to
operating system (OS). Since the BIOS is the only channel for hardware and software
to communicate, it is the key factor for system stability, and in ensuring that your
system performance as its best.
3-1 Entering Setup
Power on the computer and by pressing <Del> immediately allows you to enter Setup.
If the message disappears before your respond and you still wish to enter Setup,
restart the system to try again by turning it OFF then ON or pressing the “RESET”
button on the system case. You may also restart by simultaneously pressing <Ctrl>,
<Alt> and <Delete> keys. If you do not press the keys at the correct time and the
system does not boot, an error message will be displayed and you will again be asked
to
Press <Del> to enter Setup
3-2 BIOS Menu Screen
The following diagram show a general BIOS menu screen:
Page 26
21
3-3 Function Keys
In the above BIOS Setup main menu, you can see several options. We will explain
these options step by step in the following pages of this chapter, but let us first see a
short description of the function keys you may use here:
z
Press←→ (left, right) to select screen;
z
Press ↑↓ (up, down) to choose the item you want to confirm or to modify in the
main menu.
z
Press <Enter> to select.
Menu Bar
Menu Items
Function Keys Instruction
General Help Items
Current Setting Value
Page 27
22
z
Press <+>/<–> key when you want to modify the BIOS parameters for the active
option.
z
[F1]: Press to general help information.
z
[F2]: Press to load previous value.
z
[F3]: Press to load optimized defaults.
z
[F4]: Save and Reset.
z
Press <Esc> to quit the BIOS Setup.
3-4 Getting Help
Main Menu
The on-line description of the highlighted setup function is displayed at the top right
corner the screen.
Status Page Setup Menu/Option Page Setup Menu
Press [F1] to pop up a small help window that describes the appropriate keys to use
and the possible selections for the highlighted item. To exit the Help Window, press
<Esc>.
3-5 Menu Bar
There are six menu bars on top of BIOS screen:
Main To change system basic configuration
Advanced To change system advanced configuration
Chipset To change chipset configuration
Boot To change boot settings
Security Password settings
Save & Exit Save setting, loading and exit options.
User can press the ←/→ (left, right) arrow key on the keyboard to switch from menu
bar. The selected one is highlighted.
Page 28
23
3-6 Main Menu
Main menu screen includes some basic system information. Highlight the item and
then use the <+> / <-> key or numerical keyboard keys to select the value you want in
each item.
System Date
Set the date. Please use [TAB] to switch between data elements.
System Time
Set the time. Please use [TAB] to switch between time elements.
Page 29
24
3-7 Advanced Menu
Slide down to view more setting items:
Launch External PxE OpROM/Launch LAN1 PXE OpROM/Launch LAN2 PXE
OpROM
Use this item to enable or disable boot option for legacy network devices.
Launch Storage OpROM
Use this item to enable or disable boot option for legacy mass storage devices with
Page 30
25
option ROM.
Onboard LAN 1 Controller
Use the above items to enable or disable PCI Express root port 1.
Onboard LAN 2 Controller
Use the above items to enable or disable Mini-PCIE control.
SATA 3.0 Controller
Use the above items to enable or disable SATA 3.0 controller.
Configure SATA 3.0 as
Use this item to select an operative mode for SATA 3.0 controller.
ERP Function
Use this item to enable or disable ERP function for this board. This item should be set
as [Disabled] if you wish to have Active All Wakeup Function.
► PCI Subsystem Settings
Press [Enter] to enter and make settings for the following sub-items:
PCI ROM Priority
In the case of multiple option ROMs(Legacy and EFI compatible), specifies what
PCI option ROM to launch. The optional settings: [Legacy ROM]; [EFI Compatible
ROM].
PCI Common Settings:
PCI Latency Timer
Use this item to set value to be programmed into PCI latency timer register.
VGA Palette Snoop
Use this item to enable or disable VGA palette register snooping.
PERR# Generation
Use this item to enable or disable PCI device to generate PERR#.
SERR# Generation
Use this item to enable or disable PCI device to generate SERR#.
Page 31
26
► ACPI Settings
ACPI Sleep State
Use this item to select the highest ACPI sleep state the system will enter when the
suspend button is pressed. The optional settings are: [S1(CPU Stop Clock)];
[S3(Suspend to RAM)].
► Wakeup Function Settings
Wake System with Fixed Time
Use this item to enable or disable system wake on alarm event. When set as
[Enabled], system will wake on the hour/min/sec specified.
PS2 KB/MS Wakeup
Use this item to enable or disable PS2 KB/MS wakeup function.
PCI PME Wakeup
Use this item to enable or disable S3/S4/S5 PCI PME wakeup. This function is
only supported when ERP function is set as [Disabled].
► CPU Configuration
Hyper-Threading
The optional settings are: [Disabled]; [Enabled].Set as [Enabled] for Windows XP
and Linux (OS optimized for Hyper-Threading Technology) and [Disabled] for
other OS (OS not optimized for Hyper-Threading Technology).
Execute Disable Bit
The optional settings are: [Disabled]; [Enabled].
Limit CPUID Maximum
The optional settings are: [Disabled]; [Enabled].
This item should be set as [Disabled] for Windows XP.
► SATA Configuration
SATA Controller(s)
The optional settings are: [Disabled]; [Enabled].
Page 32
2
7
Configure SATA as
The optional settings are: [IDE Mode]; [AHCI].
► USB Configuration
Legacy USB Support
The optional settings are: [Auto]; [Disabled]; [Enabled].
EHCI Hand-off
The optional settings are: [Disabled]; [Enabled].
USB Transfer time-out
Use this item to set the time-out value for control, bulk, and interrupt transfers.
Device reset time-out
Use this item to set USB mass storage device start unit command time-out.
Device power-up delay
Use this item to set maximum time the device will take before it properly reports
itself to the host controller. ‘Auto’ uses default value: for a root port it is 100 ms, for
a hub port the delay is taken from hub descriptor. The optional settings: [Auto];
[Manual].Select [Manual] you can set value for the following sub-item:
Device Power-up delay in seconds, the delay range in from 1 to 40 seconds in
one second increments.
► Super I/O Configuration
► COM1 Port Configuration
Press [Enter] to make settings for the following items:
Serial Port
Use this item to enable or disable serial port (COM1).
Change Settings
Use this item to select an optimal setting for super IO device.
► COM2 Port Configuration
Press [Enter] to make settings for the following items:
Page 33
28
Serial Port
Use this item to enable or disable serial port (COM2).
Change Settings
Use this item to select an optimal setting for super IO device.
Serial Port Mode Select
Use this item to set COM2 port mode. The optional settings are: [RS232];
[RS422/485].
► Parallel Port Configuration
Press [enter] to make settings for the following items:
Parallel Port
Use this item to enable or disable parallel port (LPT/LPTE).
Change Settings
Use this item to select an optimal setting for super IO device.
Device Mode
Use this item to change the printer port mode.
PS2 KB/MS Connect
The optional settings are: [Keyboard First]; [Mouse First].
Case Open Select
This item is for system to detect if the case has already been opened or not. The
optional settings are: [Disabled]; [Enabled].
► PC Health Status
Press [Enter] to view hardware health status.
► Clock Generator Configuration
Clockgen Spread Spectrum
Use this item to enable or disable spread spectrum function.
IO Output Voltage
Use this item to set IO output voltage.
Page 34
29
► Voltage Configuration
DIMM Voltage
The optional settings are: [Default]; [+50mV]; [+100mV]; [+150mV].
► WatchDog Configuration
WatchDog Timer Control
Use this item to enable or disable WatchDog Timer Control. When set as
[Enabled], the following sub-items shall appear:
WatchDog Timer Value
User can set a value in the range of 4 to 255.
WatchDog Timer Unit
The optional settings are: [Second];[Minute].
► Shutdown Temperature Configuration
Use this item to select system shutdown temperature.
► SmartFan Configuration
CPUFAN1 / SYSFAN1/ SYSFAN2 Smart Mode
When set as [Enabled], the following sub-items shall appear:
CPUFAN1 / SYSFAN1/ SYSFAN2 Full Speed Temp
Use this item to set a degree for CPUFAN/SYSFAN1/SYSFAN2. FAN will run at
full speed when above this temperature.
CPUFAN1 / SYSFAN1/ SYSFAN2 Idle Temp
Use this item to set a degree for CPUFAN/SYSFAN1/SYSFAN2. FAN will idle
speed when below this temperature.
CPUFAN1 / SYSFAN1/ SYSFAN2 Stop Temp
Use this item to set a degree for CPUFAN/SYSFAN1/SYSFAN2. CPU FAN will
stop when below this temperature.
Page 35
30
3-8 Chipset Menu
► Host Bridge
Press [Enter] to make settings for Intel IGD Configuration:
Internal Graphics:
Use this item to keep IGD enabled based on the setup options. The optional
settings are: [Disabled]; [Auto].
IGFX-Boot Type
Use this item to set the video device which will be activated during POST. This has
no effect if external graphics presents. The optional settings are: [VBIOS Default];
[CRT]; [LVDS]; [HDMI+LVDS]; [CRT+LVDS].
Page 36
31
In the case IGFX-Boot Type is set as [LVDS], [HDMI+LVDS], [CRT+LVDS], the
following setting item shall appear:
LCD Panel Type:
Use this item to select LCD panel resolution.
Active LFP
The optional settings are: [Disable LVDS]; [Enable LVDS].
► South Bridge
Azalia Controller
The optional settings are: [Enabled]; [Disabled].
UHCI #1 (Ports 0 and 1)/ UHCI #2 (Ports 2 and 3)/UHCI #3 (Ports 4 and
5)/UHCI #4 (Ports 6 and 7)
Use this item to control the USB UHCI (USB 1.1) functions. The optional settings
are: [Enabled]; [Disabled].
USB 2.0 (EHCI) Support
Use this item to enable or disable USB 2.0 (EHCI) support. The optional settings
are: [Enabled]; [Disabled].
High Precision Event Timer Configuration:
High Precision Timer
The optional settings are: [Enabled]; [Disabled].
SLP_S4 Assertion Width
Use this item to select a minimum assertion width of the SLP_S4# signal.
Restore AC Power Loss
Use this item to select AC power state when power is re-applied after a power
failure. The optional settings are: [Power Off]; [Power On]; [Last State].
Page 37
32
3-9 Boot Menu
Setup Prompt Timeout
Use this item to set number of seconds to wait for setup activation key.
Bootup Numlock State
Use this item to select keyboard numlock state. The optional settings are: [On]; [Off].
Quiet Boot
The optional settings are: [Enabled]; [Disabled].
Gate A20 Active
The optional settings are: [Upon Request]; [Always].
Option ROM Message
Page 38
33
Use this item to set display mode for option ROM. The optional settings are: [Force
BIOS]; [Keep Current].
Interrupt 19 Capture
The optional settings are: [Enabled]; [Disabled].
3-10 Security Menu
Security menu allow users to change administrator password and user password
settings.
Page 39
34
3-11 Save & Exit Menu
Save Changes and Reset
This item allows user to reset the system after saving the changes.
Discard changes and Reset
This item allows user to reset the system without saving any changes.
Restore Defaults
Use this item to restore /Load default values for all the setup options.
Save as User Defaults
Use this item to save the changes done so far as user defaults.
Restore User Defaults
Use this item to restore defaults to all the setup options.
Loading...