JETWAY 939TURBO-D, 939TURBO-G, 939TURBO-P User Manual
939TURBO-D
939TURBO-G / 939TURBO-P
USER'S MANUAL
M/B For Socket 939 AMD Athlon64
Processor
NO. G03939TURBOR208
Rev:2.0
Release date: April 2005
Trademark:
* Specifications and Information contained in this documentation are furnished for information use only, and are
subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
i
USER’S NOTICE..................................................................................................................... ii
MANUAL REVISION INFORMATION .............................................................................. ii
COOLING SOLUTIONS........................................................................................................ ii
CHAPTER 1
INTRODUCTION OF 939TURBO-D/939TURBO-G/939TURBO-P MOTHERBOARD
1-1 FEATURE OF MOTHERBOARD ...................................................................................... 1
1-1.1 SPECIAL FEATURES OF MOTHERBOARD....................................................... 2
1-2 SPECIFICATION.................................................................................................................. 3
1-3 PERFORMANCE LIST........................................................................................................ 4
1-4 LAYOUT DIAGRAM & JUMPER SETTING ................................................................... 5
CHAPTER 2 HARDWARE INSTALLATION
2-1 HARDWARE INSTALLATION STEPS............................................................................. 7
2-2 CHECKING MOTHERBOARD'S JUMPER SETTING................................................... 7
2-3 INSTALL CPU....................................................................................................................... 8
2-3-1 GLOSSARY................................................................................................................ 8
2-3-2
ABOUT INTEL AMD K8 939-PIN CPU ............................................................. 9
2-4 INSTALL MEMORY............................................................................................................ 10
2-5 EXPANSION CARD.............................................................................................................. 11
2-5-1 PROCEDURE FOR EXPANSION CARD INSTALLATION ............................... 11
2-5-2 ASSIGNING IRQ FOR EXPANSION CARD......................................................... 11
2-5-3 INTERRUPT REQUEST TABLE FOR THIS MOTHERBOARD....................... 12
2-5-4 PCI-Express SLOT..................................................................................................... 12
2-6 CONNECTORS, HEADERS ................................................................................................ 13
2-6-1 CONNECTORS.......................................................................................................... 13
2-6-2 HEADERS .................................................................................................................. 16
2-7 STARTING UP YOUR COMPUTER.................................................................................. 19
CHAPTER 3 INTRODUCING BIOS
3-1 ENTERING SETUP............................................................................................................... 20
3-2 GETTING HELP ................................................................................................................... 20
3-3 THE MAIN MENU................................................................................................................ 21
3-4 STANDARD CMOS FEATURES ........................................................................................ 22
3-5 ADVANCED BIOS FEATURES.......................................................................................... 23
3-6 ADVANCED CHIPSET FEATURES .................................................................................. 25
3-6-1 DRAM TIMING SETTINGS.................................................................................... 26
3-6-2 LDT & PCI TIMING SETTINGS............................................................................ 27
3-7 INTEGRATED PERIPHERALS.......................................................................................... 27
3-7-1 ONCHIP IDE FUNCTION ....................................................................................... 28
3-7-2 ONCHIP DEVICE FUNCTION ............................................................................... 29
3-7-3 ONCHIP SUPER IO FUNCTION............................................................................ 29
3-8 POWER MANAGEMENT SETUP...................................................................................... 30
3-8-1 PM WAKE UP EVENTS.......................................................................................... 31
3-8-1.1 IRQS ACTIVITIES................................................................................................. 32
3-9 MISCELLANEOUS CONTROL ........................................................................................ 33
3-9-1 IRQ RESOURCES..................................................................................................... 33
3-10 PC HEALTH STATUS ........................................................................................................ 33
3-10-1 SMART FAN CONFIGURATIONS ..................................................................... 34
3-11 BITURBO CONFIGURATION.......................................................................................... 35
3-12 POWER USER OVERCLOCK SETTINGS...................................................................... 38
3-13 PASSWORD SETTINGS..................................................................................................... 41
3-14 LOAD STANDARD/OPTIMIZED DEFAULTS ............................................................... 41
CHAPTER 4 DRIVER & FREE PROGRAM INSTALLATION
MAGIC INSTALL SUPPORTS WINDOWS 9X/ME/NT4.0/2000/XP........................................ 42
4-1 VIA 4 IN 1 INSTALL VIA SERVICE PACK 4 IN 1 DRIVER ............................... 43
4-2 SOUND INSTALL AC97 AUDIO CODEC DRIVER ......................................... 44
4-3 LAN INSTALL REALTEK 8110S GIGA ETHERNET DRIVER................ 45
4-4 LAN2 INSTALL VIA 10/100MB LAN CONTROLLER DRIVER ................ 46
4-5 USB2.0 INSTALL VIA USB2.0 DEVICE DRIVER ........................................... 46
4-6 SATA INSTALL VIA SERIAL ATA DRIVER ............................................... 47
4-7 PC-CILLIN INSTALL PC-CILLIN2004 ANTI-VIRUS PROGRAM...................... 49
4-8 HOW TO DISABLE ON-BOARD SOUND......................................................................... 50
4-9 HOW TO UPDATE BIOS..................................................................................................... 50
4-10 Pro Magic Plus Function Introduction ................................................................................ 51
APPENDIX: Debug Port Post Code.......................................................................................i1
TABLE OF CONTENT
ii
USER’S NOTICE
COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS
MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE
REPRODUCED, TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR
BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER.
THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE 939TURBO MOTHER-
BOARD AND WE DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT WILL
CHANGE, CORRECT ANY TIME WITHOUT NOTICE. MANUFACTURER PROVIDES THIS
MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, AND WILL NOT BE LIABLE FOR ANY
INDIRECT, SPECIAL, INCIDENTIAL OR CONSEQUENTIAL DAMAGES (INCLUDING
DAMANGES FOR LOSS OF PROFIT, LOSS OF BUSINESS, LOSS OF USE OF DATA,
INTERRUPTION OF BUSINESS AND THE LIKE).
PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE
REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES, AND
THEY ARE USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER’S
BENEFIT, WITHOUT INTENT TO INFRINGE.
Manual Revision Information
Reversion Revision History Date
2.0 Second Edition April 2005
Item Checklist
5
939TURBO-D/939TURBO-G/939TURBO-P motherboard
5
Cable for IDE/Floppy
5
CD for motherboard utilities
Cable for USB Port 3/4 (Option)
5
Cable for Serial ATA IDE Port
5
SPDIF-IN/SPDIF-OUT Adaptor
5
939TURBO-D/939TURBO-G/939TURBO-P User’s Manual
AMD K8 Processor Family
Cooling Solutions
As processor technology pushes to faster speeds and higher performance with increasing operation
clock, thermal management becomes increasingly crucial while building computer systems. Maintaining
the proper computing environment without thermal increasing is the key to reliable, stable, and 24
hours system operation. The overall goal is keeping the processor below its specified maximum case
temperature. Heatsinks induce improved processor heat dissipation through increasing surface area
and concentrated airflow from attached active cooling fans. In addition, interface materials allow
effective transfers of heat from the processor to the heatsink. For optimum heat transfer, AMD
recommends the use of thermal grease and mounting clips to attach the heatsink to the processor.
Please refer to the website below for collection of heatsinks evaluated and recommended for Socket939 processors by AMD. In addition, this collection is not intended to be a comprehensive listing of
all heatsinks that support Socket-939 processors.
For vendor list of heatsinks and Active cooling fans, please visit
http://www.amd.com/us-en/Processors/DevelopWithAMD/0,,30_2252_869_9460^9515,00.html
1
Chapter 1
Introduction of 939TURBO-D/939TURBO-G/939TURBO-P
Motherboard
1-1 Feature of motherboard
The 939TURBO-D/939TURBO-G/939TURBO-P motherboard is designed for use 64bit AMD
Athlon64 (K8) Processor in 939 Pin HyperTrnsport Processor with the VIA K8T890 Chipset
delivers a high performance and professional desktop platform solution. Which utilize the
Socket 939 design and the memory size expandable to 4.0GB.
The motherboard use the newest VIA K8T890 Chipset, supports 1GHz System Bus in data
transfer rate. The motherboard provided 133MHz/166MHz/200MHz Memory clock frequency,
support DDR266/DDR333/DDR400 DDR Module and Dual channel function. The
motherboard embedded VIA VT8237 V-Link LPC South Bridge offer ULTRA
ATA 133
and
Serial ATA RAID 0, 1
functions to provide speedier HDD throughout that boosts overall
system performance.
939TURBO-D/939TURBO-G provided Giga LAN function used the RealTek RT8110S GigaLAN controller chip supports 10M/100M/1Gbps data transfer rate provided full duplex, half
duplex operation. 939TURBO-D/939TURBO-P used VIA VT6103 LAN PHY chip support
10/100Mbps data transfer rate provided full duplex, half duplex function.
The motherboard also has an integrated 8-channel AC’97 CODEC on board which is fully
compatible with Sound Blaster Pro that gives you the best sound quality and compatibility.
939TURBO-D/939TURBO-G/939TURBO-P provided one PCI-Express x16 graphics slot
delivers up to 4Gbyte/sec data transfer rate per direction, 3.5 times more bandwidth than
AGP8X and up to 8Gbyte/sec concurrent bandwidth. Two PCI Express x1 I/O offers
512Mbyte/sec concurrently, over 3.5 times more bandwidth than PCI at 133Mbye/sec,
tackling the most demanding multimedia tasks nowadays.
With USB control as well as capability of expanding to 8x USB2.0 function ports delivering
480Mb/s bandwidth and rich connectivity, these motherboards meet future USB demand also
has built-in hardware monitor function to monitor and protect your computer.
Some special features---
Bi-turbo/ CPU Thermal Throttling/ CPU Vcore 7-shift/ CPU Smart
Fan/ Debug Port(Option)
in this motherboard for power user to use the over-clocking
function more flexible. For detail description please read next section.
This motherboard provided high performance & meets future specification demand. It is
really wise choice for your computer.
2
1-1.1 Special Features of motherboard
Bi-turbo Technology
---( Hardware-based Dynamic Over-clocking )
The Bi-turbo Technology offers you dual over-clocking modes. On top of the software based
BIOS setting “Current CPU Clock” for over-clocking, the onboard hardware circuitry will
monitor the change of CPU current to activate 2nd level over-clocking at preset workload level
automatically. The Bi-turbo technology offers the versatility of both hardware-based
intelligent automatic mode and power-manual mode for extra computing performance.
Without complex settings from system BIOS, Bi-turbo provides the seeing promoted system
performance by simple and intuitional BIOS setting. Bi-turbo technology offers more flexible
ways to choose the over-clocking range of over-clocking activation by actually CPU hardware
loading you define. (for detail operating please read Section 3-11 Bi-turbo Configuration)
CPU Thermal Throttling Technology---(The CPU Overheat Protection Technology)
To prevent the increasing heat from damage of CPU or accidental shutdown while at high
workload, the CPU Thermal Throttling Technology will force CPU to enter partially idle
mode from 87.5% to 12.5% according to preset CPU operating temperature in BIOS (from 40
to 90). When the system senses the CPU operating temperature reaching the preset value,
the CPU operating bandwidth will be decreased to the preset idle percentage to cool down the
processor. When at throttling mode the beeper sound can be optionally selected to indicate it
is in working. ( for detail operating please read Section 3-11 Bi-turbo Configuration)
Debug Port (Option)--- ( The Professional Hardware Diagnosis System )
Being bugged of abnormal system failure through the tossed and turned nights no more, the
embedded Hardware Debug Port offers you the real-time visual system healthy for the
demanding usage of computing. No more bugging by unknown system failure and no more
time wasted in the first moment of 24-hour nonstop ping business computing, the embedded
Debug Port will turn you into a well training hardware professional with the seeing system
situation. (The Post Code please refer Appendix)
CPU Smart Fan---( The Noise Management System )
It’s never been a good idea to gain the performance of your system by sacrificing its acoustics.
CPU Smart Fan Noise Management System is the answer to control the noise level needed for
now-a-day’s high performance computing system. The system will automatically increase the
fan speed when CPU operating loading is high, after the CPU is in normal operating condition,
the system will low down the fan speed for the silent operating environment. The system can
provide the much longer life cycle for both CPU and the system fans for game use and
business requirements.
CPU Vcore 7-Shift--- ( Shift to Higher Performance )
The CPU voltage can be adjusted up by 7 steps for the precisely over-clocking of extra
demanding computing performance.
3
1-2 Specification
Spec Description
Design
∗
ATX form factor 4 layers PCB size: 30.5x24.4cm
Chipset
∗
VIA K8T890 North Bridge Chipset
∗
VIA VT8237 South Bridge Chipset
CPU Socket 939
∗
Support 64bit AMD Athlon64 939-Pin package utilizes FlipChip Pin Grid Array package processor
∗
Support CPU Frequency 1GMHz
∗
Support up to 3800+ processor
∗
Reserves support for future AMD Athlon64 939-pin processors
Memory Socket
∗
184-pin DDR Module socket x 4
∗
Support 4pcs DDR266/DDR33/DDR400 DDR Modules
Expandable to 4.0GB
∗
Support Dual channel function
Expansion Slot
∗
PCI-Express x16 slot 1pcs delivers up to 8GB/s concurrent
bandwidth
∗
PCI-Express x1 slot 2pcs delivers up to 512MB/s concurrent
bandwidth
∗
32-bit PCI slot x 3pcs
Integrate IDE and
Serial ATA RAID
∗
Two PCI IDE controllers support PCI Bus Mastering, ATA
PIO/DMA and the ULTRA DMA 33/66/100/133 functions that
deliver the data transfer rate up to 133 MB/s; Two Serial ATA
ports provide 150 MB/sec data transfer rate for two Serial ATA
Devices and offer RAID 0, 1 functions
Dual LAN
(only for 939TURBO-D)
∗
Integrated RealTek RT8110S PCI-Giga LAN chip for
939TURBO-D/939TURBO-G
∗
Supports Fast Ethernet LAN function provide 10Mb/100Mb/
1Gb /s data transfer rate
∗
Integrated VIA VT6103 LAN PHY chip, supports 10/100 Mb/s
data transfer rate for 939TURBO-D/939TURBO-P
8CH-Audio
∗
AC’97 Digital Audio controller integrated
∗
8-channel AC’97 Audio CODEC on board
∗
SPDIF-In/ SPDIF-Out Optical support (Cable optional)
∗
Audio driver and utility included
BIOS
∗
Award 4MB Flash ROM
Multi I/O
∗
PS/2 keyboard and PS/2 mouse connectors
∗
Floppy disk drive connector x1
∗
Parallel port x1
∗
Serial port x2
∗
USB2.0 port x 4 and headers x 4 (connecting cable option)
∗
Audio connector (Line-in, Line-out, MIC/ 8CH Audio)
1-3 Performance List
4
The following performance data list is the testing result of some popular benchmark
testing programs. These data are just referred by users, and there is no responsibility
for different testing data values gotten by users (the different Hardware & Software
configuration will result in different benchmark testing results.)
Performance Test Report
CPU:
AMD K8 Athlon64 3800+ Support (Socket 939, 512k L2 cache)
DRAM:
TwinMOS Hynix HY5DU56822CT 512MB DDR400 X 2 (1Gbyte) Memory
VGA Card :
ATI X800 256M PCI EXPRESS VGA CARD (1024X768X32BIT Color)
Hard Disk Driver:
Seagate Barracude 7200.7 SATA150
BIOS:
Award Optimal default
OS:
Windows XP Professional (SERVICE PACK 2)
200/200
Single channel
200/200
Dual channel
3D Mark 2001SE 21178 22066
3D Mark 2003 8669 8796
3D Mark 2005 3926 3937
AQUAMRK3 N/A N/A
PCMark2004
System / CPU / Memory 4538 / 4454 / 3485 4719 / 4524 / 5472
Graph / HDD 5109 / 4607 5036 / 4637
Content Creation Winstone 2004 34.8 36
Business Winstone 2004 26.9 26.9
Winbench 99 V2.0:
Business/Hi-end Disk Winmark99 19700 / 42400 19500 / 41600
Business/Hi-end Graphic Winmark 1200 / 2220 1190 / 2210
SISMark 2004: SISMark Rating(Internet Content Creation / Office Productivity )
SISMark 2004 192 (209 / 177) 200 (212 / 188)
3D Creation / 2D Creation 191 / 256 197 / 264
/ Web publication 186 184
Communication / Document Creation 188 / 194 187 / 202
/ Data Analysis 151 175
SISOFT Sandra 2004 : 1.CPU Arithmetic Benchmark 2.Memory bandwidth
Benchmark 3.CPU Multi-Media Benchmark
1.Dhrystone ALU MIPS 10333 10366
Whetstone FPU iSSE2 FLOPS 3965 / 5105 3931 / 5160
2.Int/Float Buffered iSSE2 MB/S 2724 / 2732 6003 / 5966
3.Integer/Floating-Point SSE2 IT/S 23066 / 24887 23061 / 24884
UT2003 Benchmark (flyby/botmatch) 287.59 / 91.87 297.82 / 94.94
Quake3 DEMO1 / DEMO2 FPS 350.3 / 344.7 356.4 / 351.5
Return to Castle Wolfenstein FPS 183.6 195.0
Super Pi (1M) Second 40s 36s
CPUZ System / CPU Clock 200 / 200 / 2399.7 200 / 200 / 2399.8
1-4 Layout Diagram & Jumper Setting
5
Jumpers
USB Port
(USB2, USB3)
COM1
COM2
USB1
PS/2 Mouse
PS/2 Keyboard
USB
Line-IN
MIC-IN
Line-OUT
CEN/LFE
Surround
PRINTER
Giga LAN Surrback
10/100M
LAN
4MBit Flash ROM BIOS
Floppy Connector
Front Panel Connector
ATA 133 IDE Connector
(IDE1, IDE2)
Clear CMOS (JBAT)
VIA VT8237 Chip
Speaker/Power LED Connector
VIA K8T890 Chipset
CPU Socket
DDR Socket X4
ATX Power Connector
Serial-ATA Connector
(SATA1, 2)
USB Power On Jumper (JP3)
PCI EXPRESSx16
SFAN2
Front Panel Audio
CD Audio In
RTL8110S 1G LAN Chip
PCI Slot
8-CH AC’97 Audio Codec
On board LAN Jumper (JP2)
PCI EXPRESSx1
VIA 6103L LAN PHY Chip
PC99 Back Panel
PS2 KB/Mouse Port
CPU FAN
USB Port
/
10/100M LAN Connector
Audio Connector
KBMS/USB Power On Jumper (JP1)
SFAN1
FINTEK F71805F I/O chip
ATX 12V Power Connector
USB Port/ Giga LAN Connecto
r
SPDIF Connector
6
Jumper Name Description Page
JBAT CMOS RAM Clear 3-pin Block P.7
JP1 Keyboard/USB0,1 Power On
Enabled/Disabled
3-pin Block P.8
JP2 On board RealTek LAN Enabled/Disabled 3-pin Block P.8
JP3 USB Power On Enabled/Disabled 3-pin Block P.8
Connectors
Connector Name Description Page
ATXPWR24P ATX Power Connector 24-pin Block P.13
ATX12V ATX 12V Power Connector 4-pin Block P.13
PS2KBMS PS/2 Mouse & PS/2 Keyboard
Connector
6-pin Female P.14
USB/USB1 USB Port Connector 4-pin Connector P.14
UL1 10/100M LAN Port Connector RJ-45 Connector P.14
USBLAN Giga-LAN Port Connector RJ-45 Connector P.14
PARALLEL Parallel Port Connector 25-pin Female P.14
J1 8-CH Audio Connector 6 phone jack Connector P.14
COM1/COM2 Serial Port COM1/COM2 Connector 9-pin Connector P.14
FDD Floppy Driver Connector 34-pin Block P.14
IDE1/IDE2 Primary/Secondary IDE Connector 40-pin Block P.15
SATA1/SATA2 Serial ATA IDE Connector 7-pin Connector P.16
Headers
Header Name Description Page
AUDIO SPEAKER, MIC header 9-pin Block P.16
USB2, USB3 USB Port Headers 9-pin Block P.16
SPEAK PC Speaker connector 4-pin Block P.17
PWR LED Power LED 3-pin Block P.17
JW_FP
(Power LED/Reset/
IDE LED/Power
Button)
Front Panel Header
(including Power LED/ IDE activity
LED/Reset switch / Power On Button
lead)
9-pin Block P.17
SFAN1, SFAN2
CPUFAN
FAN Headers 3-pin Block P.17
CDIN CD Audio-In Header 4-pin Block P.17
SPDIF Optical In/Out Header 9-pin Block P.18
Expansion Sockets
Socket/Slot Name Description Page
ZIF Socket 939 CPU Socket 939-pin mPGAB Athlon64 CPU
Socket
P.9
DIMM1~4 DDR Module Socket 184-pin DDR Module Socket
P.10
PCI1∼ PCI3
PCI Slot 32-bit PCI Local Bus Expansion slots
P.11
PE1 PCI-Express x16 Slot PCI-Express x16 Expansion Slot
P.12
PE2,PE3 PCI-Express x1 Slot PCI-Express x1 Expansion Slot
P.12
Chapter 2
7
Hardware Installation
2-1 Hardware installation Steps
Before using your computer, you had better complete the following steps:
1. Check motherboard jumper setting
2. Install CPU and Fan
3. Install System Memory (DIMM)
4. Install Expansion cards
5. Connect IDE and Floppy cables, Front Panel /Back Panel cable
6. Connect ATX Power cable
7. Power-On and Load Standard Default
8. Reboot
9. Install Operating System
10. Install Driver and Utility
2-2 Checking Motherboard’s Jumper Setting
(1) CMOS RAM Clear (3-pin) : JBAT
A battery must be used to retain the motherboard configuration in CMOS RAM short 1-2
pins of JBAT to store the CMOS data.
To clear the CMOS, follow the procedure below:
1. Turn off the system and unplug the AC power
2. Remove ATX power cable from ATX power connector
3. Locate JBAT and short pins 2-3 for a few seconds
4. Return JBAT to its normal setting by shorting pins 1-2
5. Connect ATX power cable back to ATX power connector
Note: When should clear CMOS
1. Troubleshooting
2. Forget password
3. After over clocking system boot fail
CMOS RAM Clear Setting
2-3 closed Clear CMOS
JBAT
13
JBAT
13
1-2 closed Normal
(2) On Board RealTek LAN function Enabled/Disabled: JP2
8
On Board RealTek LAN Setting
2-3 closed On Board RealTek LAN Disabled
JP2
13
JP2
13
1-2 closed On Board RealTek LAN Enabled
(Default)
(3) Keyboard/USB Power On function Enabled/Disabled: JP1, JP3
Keyboard/Mouse & USB Power On Setting
2-3 closed KB/USB Power ON Enabled
JP1
1
3
JP1
1
3
1-2 closed KB/USB Pow er ON Disable
(Default)
USB2/USB3 Power On Setting
2-3 closed USB Power On Enabled
JP3
1 3
JP3
13
1-2 closed USB Power On Disable
(Default)
2-3 Install CPU
2-3-1 Glossary
Chipset (or core logic) - two or more integrated circuits which control the interfaces between
the system processor, RAM, I/O devises, and adapter cards.
Processor slot/socket - the slot or socket used to mount the system processor on the
motherboard.
Slot (PCI-E, PCI, RAM) - the slots used to mount adapter cards and system RAM.
AGP - Accelerated Graphics Port - a high speed interface for video cards; runs at 1X
(66MHz), 2X (133MHz), or 4X (266MHz),
or 8X (533MHz).
PCI - Peripheral Component Interconnect - a high speed interface for video cards, sound
cards, network interface cards, and modems; runs at 33MHz.
PCI Express- Peripheral Component Interconnect Express- a high speed interface for video
cards, sound cards, network interface cards, and modems.
Serial Port - a low speed interface typically used for mouse and external modems.
Parallel Port - a low speed interface typically used for printers.
PS/2 - a low speed interface used for mouse and keyboards.
USB - Universal Serial Bus - a medium speed interface typically used for mouse, keyboards,
scanners, and some digital cameras.
Sound (interface) - the interface between the sound card or integrated sound connectors and
9
speakers, MIC, game controllers, and MIDI sound devices.
LAN (interface) - Local Area Network - the interface to your local area network.
BIOS (Basic Input/Output System) - the program logic used to boot up a computer and
establish the relationship between the various components.
Driver - software, which defines the characteristics of a device for use by another device or
other software.
Processor - the "central processing unit" (CPU); the principal integrated circuit used for doing
the "computing" in "personal computer"
Front Side Bus Frequency -
the working frequency of the motherboard, which is generated
by the clock generator for CPU, DRAM and PCI BUS.
CPU L2 Cache -
the flash memory inside the CPU, normal it depend on CPU type.
2-3-2 About AMD Athlon64 939-pin CPU
This motherboard provides a 939-pin surface mount, Zero Insertion Force (ZIF) socket,
referred to as the mPGA939 socket supports AMD Athlon64 processor in the 939 Pin package
utilizes Flip-Chip Pin Grid Array package technology.
The CPU that comes with the motherboard should have a cooling FAN attached to prevent
overheating. If this is not the case, then purchase a correct cooling FAN before you turn on
your system.
WARNING!
Be sure that there is sufficient air circulation across the processor’s
heatsink and CPU cooling FAN is working correctly, otherwise it may
cause the processor and motherboard overheat and damage, you may install
an auxiliary cooling FAN, if necessary.
To install a CPU, first turn off your system and remove its cover. Locate the ZIF socket and
open it by first pulling the level sideways away from the socket then upward to a 90-degree
angle. Insert the CPU with the correct orientation as shown below. The notched corner
should point toward the end of the level. Because the CPU has a corner pin for two of the
four corners, the CPU will only fit in the orientation as shown.
CPU ZIF mPGAB Socket
Colden Arrow
Socket 939
When you put the CPU into the ZIF socket. No force require to insert of the CPU, then press
the level to Locate position slightly without any extra force.
2-4 Install Memory
10
This motherboard provides four 184-pin DDR DUAL INLINE MEMORY MODULES
(DIMM) sites for DDR memory expansion available from minimum memory size of 64MB to
maximum memory size of 4.0GB DDR SDRAM.
Valid Memory Configurations
Bank 184-Pin DIMM PCS Total Memory
Bank 0, 1 (DIMM1) DDRDDR266/DDR333/DDR400
DDR SDRAM Module
X1
128MB∼1.0GB
Bank 2, 3 (DIMM2) DDRDDR266/DDR333/DDR400
DDR SDRAM Module
X1
128MB∼1.0GB
Bank 4, 5 (DIMM3) DDRDDR266/DDR333/DDR400
DDR SDRAM Module
X1
128MB∼1.0GB
Bank 6,7 (DIMM4) DDRDDR266/DDR333/DDR400
DDR SDRAM Module
X1
128MB∼1.0GB
Total System Memory (Max. 4.0GB) 4
128MB∼4.0GB
For Dual channel Limited!
1. Dual channel function only supports when 2 DIMM Modules plug in either both DIMM1 &
DIMM2 or DIMM3 &DIMM4, or four DIMM Modules plug in DIMM1~DIMM4.
2. DIMM1 & DIMM2, or DIMM3 & DIMM4 must be the same type, same size, same frequency
for dual channel function.
Generally, installing DDR SDRAM modules to your motherboard is very easy, you can refer
to figure 2-4 to see what a 184-Pin DDR266/DDR333/DDR400 DDR SDRAM module looks
like.
DIMM2 (BANK2+BANK3)
DIMM1 (BANK0+BANK1)
DIMM4 (BANK6+BANK7)
DIMM3 (BANK4+BANK5)
DIMM1 & DIMM 2: Dual Channel 1
DIMM3 & DIMM 4: Dual Channel 2
NOTE!
When you install DIMM module fully into the DIMM socket the eject tab
should be locked into the DIMM module very firmly and fit into its
indention on both sides.
WARNING!
For the DDR SDRAM CLOCK is set at 200MHz, use only DDR400- compliant
DDR Modules. When this motherboard operate at 200Mhz, most system will
not even boot if non-compliant modules are used because of the strict
Figure 2-4
11
timing issues, if your DDR Modules are not DDR400-compliant, set the
SDRAM clock to 133MHz to ensure system stability.
2-5 Expansion Cards
WARNING!
Turn off your power when adding or removing expansion cards or other
system components. Failure to do so may cause severe damage to both
your motherboard and expansion cards.
2-5-1 Procedure For Expansion Card Installation
1. Read the documentation for your expansion card and make any necessary hardware or
software setting for your expansion card such as jumpers.
2. Remove your computer’s cover and the bracket plate on the slot you intend to use.
3. Align the card’s connectors and press firmly.
4. Secure the card on the slot with the screen you remove above.
5. Replace the computer system’s cover.
6. Set up the BIOS if necessary.
7. Install the necessary software driver for your expansion card.
2-5-2 Assigning IRQs For Expansion Card
Some expansion cards need an IRQ to operate. Generally, an IRQ must exclusively assign to
one use. In a standard design, there are 16 IRQs available but most of them are already in use.
Standard Interrupt Assignments
IRQ Priority Standard function
0 N/A System Timer
1 N/A Keyboard Controller
2 N/A Programmable Interrupt
3 * 8 Communications Port (COM2)
4 * 9 Communications Port (COM1)
5 * 6 Sound Card (sometimes LPT2)
6 * 11 Floppy Disk Controller
7 * 7 Printer Port (LPT1)
8 N/A System CMOS/Real Time Clock
9 * 10 ACPI Mode when enabled
10 * 3 IRQ Holder for PCI Steering
11 * 2 IRQ Holder for PCI Steering
12 * 4 PS/2 Compatible Mouse Port
13 N/A Numeric Data Processor
14 * 5 Primary IDE Channel
15 * 1 Secondary IDE Channel
* These IRQs are usually available for ISA or PCI devices.
2-5-3 Interrupt Request Table For This Motherboard
Interrupt request are shared as shown the table below:
INT A INT B INT C INT D INT E INT F INT G INT H
12
Slot 1
√
Slot 2
√
Slot 3
√
Onboard USB 1
√
Onboard USB 2
√
AC97/MC97
√
IMPORTANT!
If using PCI cards on shared slots, make sure that the drivers support
“Shared IRQ” or that the cards don’t need IRQ assignments. Conflicts will
arise between the two PCI groups that will make the system unstable or
cards inoperable.
2-5-4 PCI Express Slot
This motherboard provides one 16-lane PCI Express slot intended for Graphics Attach, and
two x1 PCI Express Slot. Fully compliant to the PCI Express Base Specification revision
1.0a , support PCI Express VGA card, and other PCI Express device.
2-6 Connectors, Headers
2-6-1 Connectors
(1) Power Connector (24-pin block) : ATXPWR24P
13
ATX Power Supply connector. This is a new defined 24-pins connector that usually
comes with ATX case. The ATX Power Supply allows to use soft power on momentary
switch that connect from the front panel switch to 2-pins Power On jumper pole on the
motherboard. When the power switch on the back of the ATX power supply turned on,
the full power will not come into the system board until the front panel switch is
momentarily pressed. Press this switch again will turn off the power to the system
board.
** We recommend that you use an ATX 12V Specification 2.0-compliant power supply
unit (PSU) with a minimum of 350W power rating. This type has 24-pin and 4-pin
power plugs.
** If you intend to use a PSU with 20-pin and 4-pin power plugs, make sure that the 20-pin
power plug can provide at least 15A on +12V and the power supply unit has a minimum
power rating of 350W. The system may become unstable or may not boot up if the
power is inadequate.
(2) ATX 12V Power Connector (4-pin block) : ATX12V
This is a new defined 4-pins connector that usually comes with ATX Power Supply. The
ATX Power Supply which fully support Pentium 4 processor must including this
connector for support extra 12V voltage to maintain system power consumption.
Without this connector might cause system unstable because the power supply can not
provide sufficient current for system.
(3) PS/2 Mouse & PS/2 Keyboard Connector: PS2KBMS
The connectors for PS/2 keyboard and PS/2 Mouse.
(4) USB Port connector: USB0/USB1
Pin 1
ROW1 ROW 2
24-Pin
ROW1 ROW 2
Pin 1
20-Pin
PIN ROW1 ROW2
1 3.3V 3.3V
2 3.3V -12V
3 GND GND
4 5V Soft Power On
5 GND GND
6 5V GND
7 GND GND
8 Power OK -5V
9 +5V (for Soft Logic) +5V
10 +12V +5V
11 +12V +5V
12 +3V GND
Pin 1
14
The connectors are 4-pin connector that connect USB devices to the system board.
(5) LAN Port connector: UL1/USBLAN
This connector is standard RJ45 connector for Network
The UL1 support 10M/100Mb/s data transfer rate (not for 939TURBO-G)
The USBLAN support 10M/100M/1G b/s data transfer rate (not for 939TURBO-P)
(6) Parallel Port Connector (25-pin female): PARALLEL
Parallel Port connector is a 25-pin D-Subminiature Receptacle connector. The Onboard Parallel Port can be disabled through the BIOS SETUP. Please refer to Chapter 3
“INTEGRATED PERIPHERALS SETUP” section for more detail information.
(7) Audio Line-In,
Lin
-Out, MIC, Surrback, Surround, CEN/LEF Connector : J1
This Connector are 6 phone Jack for LINE-OUT, LINE-IN, MIC, Surrback, Surround,
CEN/LEF
Line-in : (BLUE)
Audio input to sound chip
Line-out : (GREEN)
Audio output to speaker
MIC : (PINK)
Microphone Connector
Surrback : (ORANGE)
Audio output to speaker-Rear speaker out
CEN/LEF : (BLACKNESS)
Audio output to speaker-Center/Subwoofer speaker out
Surround: (GRAY)
Audio output to speaker-Side speaker out
(8) Serial Port COM1/COM2 : COM1/COM2
COM1 is the 9-pin D-Subminiature male connector. The On-board serial port can be
disabled through BIOS SETUP. Please refer to Chapter 3 “INTEGRATED PERIPHERALS
SETUP” section for more detail information.
(9) Floppy drive Connector (34-pin block): FDD
This connector supports the provided floppy drive ribbon cable. After connecting the
single plug end to motherboard, connect the two plugs at other end to the floppy drives.
PS/2
Mouse
PS/2
Keyboard
COM1
COM2
USB1
PRINTER
Giga LAN
USB
Surround
Line-IN
MIC-IN
Line-OUT
Surrback
CEN/LFE
10/100M
LAN
15
Floppy Drive Connector
Pin 1
FDD
(10) Primary IDE Connector (40-pin block): IDE1
This connector supports the provided IDE hard disk ribbon cable. After connecting the
single plug end to motherboard, connect the two plugs at other end to your hard disk(s).
If you install two hard disks, you must configure the second drive to Slave mode by
setting its jumpers accordingly. Please refer to the documentation of your hard disk for
the jumper settings.
Primary IDE Connector
Pin 1
IDE1
(11) Secondary IDE Connector (40-pin block): IDE2
This connector connects to the next set of Master and Slave hard disks. Follow the
same procedure described for the primary IDE connector. You may also configure two
hard disks to be both Masters using one ribbon cable on the primary IDE connector and
another ribbon cable on the secondary IDE connector.
Secondary IDE Connector
Pin 1
IDE2
16
•
Two hard disks can be connected to each connector. The first HDD is referred to as the
“Master” and the second HDD is referred to as the “Slave”.
•
For performance issues, we strongly suggest you don’t install a CD-ROM or DVD-ROM
drive on the same IDE channel as a hard disk. Otherwise, the system performance on this
channel may drop.
(12) Serial-ATA Port connector: SATA1/SATA2
This connector support the provided Serial ATA IDE hard disk cable to connecting the
motherboard and serial ATA hard disk.
Serial-ATA Port Connector
SATA2
SATA1
2-6-2 Headers
(1) Line-Out/MIC Header for Front Panel (9-pin): AUDIO
This header connect to Front Panel Line-out, MIC connector with cable.
Without install the cable, this header default setting is 5-6 short, 9-10 short. When you
install the cable you have take off these jumpers.
Line-Out, MIC Headers
AUDIO
Pin 1
AUD
_
MIC
AUD
_
FPOUT
_
L
AUD
_
MIC
_
BIAS
AUD
_
FPOUT
_
R
HP
_
ON
AUD
_
GND
AUD
_
RET
_
L
AUD
_
RET
_
R
AUD
_
VCC
2
9
10
(2) USB Port Headers (9-pin) : USB2/USB3
These headers are used for connecting the additional USB port plug. By attaching an
option USB cable, your can be provided with two additional USB plugs affixed to the
back panel.
Loading...