Jetway 865PEDAP User Manual

865GDA/865GDAP

865PEDA/865PEDAP

USER'S MANUAL

M/B For Socket 478 Pentium 4 Processor

NO. G03-865GDA1A

Release date: June 2003

Trademark:

* Specifications and Information contained in this documentation are furnished for information use only, and are

subject to change at any time without notice, and should not be construed as a commitment by manufacturer.

USER’S NOTICE........................................................................................................................... ii

MANUAL REVISION INFORMATION.......................................................................................... ii

COOLING SOLUTIONS ..............................................................................................................ii

CHAPTER 1 INTRODUCTION OF 865GDA/865GDAP/865PEDA/865PEDAP MOTHERBOARD

1-1 FEATURE OF MOTHERBOARD...................................................................................... 1

1-2 SPECIFICATION ........................................................................................................... 2

1-3 PERFORMANCE LIST .................................................................................................... 3

1-4 LAYOUT DIAGRAM & JUMPER SETTING .....................................................................4

CHAPTER 2 HARDWARE INSTALLATION

2-1 HARDWARE INSTALLATION STEPS............................................................................... 6

2-2 CHECKING MOTHERBOARD'S JUMPER SETTING .......................................................6

2-3 INSTALL CPU ................................................................................................................ 7

2-3-1 GLOSSARY....................................................................................................... 7

2-3-2 ABOUT INTEL PENTIUM 4 478-PIN CPU........................................................... 8

2-4 INSTALL MEMORY .......................................................................................................8

2-5 EXPANSION CARD...................................................................................................... 9

2-5-1 PROCEDURE FOR EXPANSION CARD INSTALLATION ................................... 9

2-5-2 ASSIGNING IRQ FOR EXPANSION CARD ...................................................... 10

2-5-3 INTERRUPT REQUEST TABLE FOR THIS MOTHERBOARD ..................................10

2-5-4 AGP SLOT ........................................................................................................11

2-6 CONNECTORS, HEADERS ...........................................................................................11

2-6-1 CONNECTORS................................................................................................. 11

2-6-2 HEADERS.......................................................................................................... 14

2-7 STARTING UP YOUR COMPUTER................................................................................. 18

CHAPTER 3 INTRODUCING BIOS

3-1 ENTERING SETUP.......................................................................................................... 19

3-2 GETTING HELP .............................................................................................................19

3-3 THE MAIN MENU.......................................................................................................... 20

3-4 STANDARD CMOS FEATURES...................................................................................... 21

3-5 ADVANCED BIOS FEATURES ....................................................................................... 22

3-6 ADVANCED CHIPSET FEATURES .................................................................................24

3-6-1 DRAM TIMING SETTINGS ................................................................................25

3-7 INTEGRATED PERIPHERALS..........................................................................................26

3-7-1 ONBOARD IDE FUNCTION .............................................................................26

3-7-2 ONBOARD DEVICE FUNCTION ......................................................................27

3-7-3 ONBOARD SUPER IO FUNCTION.................................................................... 28

3-8 POWER MANAGEMENT SETUP.................................................................................... 29

3-8-1 PM TIMER RELOAD EVENTS ............................................................................ 30

3-9 PNP/PCI CONFIGURATION SETUP.............................................................................. 31

3-9-1 IRQ RESOURCES ............................................................................................. 32

3-10 PC HEALTH STATUS..................................................................................................... 32

3-11 MISCELLANEOUS CONTROL...................................................................................... 33

3-12 LOAD STANDARD/OPTIMIZED DEFAULTS..................................................................34

3-13 SET SUPERVISOR/USER PASSWORD........................................................................... 34

CHAPTER 4 DRIVER & FREE PROGRAM INSTALLATION

MAGIC INSTALL SUPPORTS WINDOWS 98SE/ME/NT4.0/2000/XP .....................................35

4-1 INF INSTALL INTEL 865 CHIPSET SYSTEM DRIVER ....................................... 36

4-2 VGA INSTALL INTEL 865G VGA DRIVER....................................................... 36

4-3 SOUND INSTALL ALC AC97’ CODEC AUDIO DRIVER ..................................... 37

4-4 LAN INSTALL VIA 6105 LAN CONTROLLER DRIVER .................................... 38

4-5 USB2.0 INSTALL INTEL USB2.0 DRIVER.............................................................. 39

4-6 PC-HEALTH INSTALL SMART GUARDIAN SOFTWARE FOR HARDWARE

4-6-1 HOW TO UTILIZE PC-HEALTH.......................................................................... 40

4-7 MBIOS&DX8 INSTALL BIOS LIVE UPDATE UTILITY AND DIRECTX8.1......................... 41

4-8 PC-CILLIN INSTALL PC-CILLIN2002 ANTI-VIRUS PROGRAM ...............................42

4-9 HOW TO UPDATE BIOS ................................................................................................ 44

TABLE OF CONTENT

MONITORING DEVICE.........................................................................39

i

USER’S NOTICE

COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL,
INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED,
TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT
WRITTEN PERMISSION OF THE MANUFACTURER.

THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE 865GDA/865GDAP/ 865PEDA/
865PEDAP MOTHER-BOARD AND WE DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT
WILL CHANGE, CORRECT ANY TIME WITHOUT NOTICE. MANUFACTURER PROVIDES THIS MANUAL “AS
IS” WITHOUT WARRANTY OF ANY KIND, AND WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTIAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMANGES FOR LOSS OF PROFIT, LOSS OF
BUSINESS, LOSS OF USE OF DATA, INTERRUPTION OF BUSINESS AND THE LIKE).

PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE
REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES, AND THEY ARE
USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER’S BENEFIT, WITHOUT
INTENT TO INFRINGE.

Manual Revision Information

Reversion Revision History Date

1.0 First Release June 2003

Item Checklist

5

865GDA/865GDAP/ 865PEDA/865PEDAP Motherboard

5

Cable for IDE/Floppy

5

CD for motherboard utilities

□

Cable for USB2 Port (Option)

5

Cable for Serial ATA IDE Port

5

SPDIF-IN/SPDIF-OUT Adaptor (Option)

5

865GDA/865GDAP/ 865PEDA/865PEDAP User’s Manual

Intel Pentium 4 Processor Family
Cooling Solutions

As processor technology pushes to faster speeds and higher performance, thermal management
becomes increasingly crucial when building computer systems. Maintaining the proper thermal
environment is key to reliable, long-term system operation. The overall goal in providing the proper
thermal environment is keeping the processor below its specified maximum case temperature.
Heatsinks induce improved processor heat dissipation through increased surface area and
concentrated airflow from attached fans. In addition, interface materials allow effective transfers of
heat from the processor to the heatsink. For optimum heat transfer, Intel recommends the use of
thermal grease and mounting clips to attach the heatsink to the processor.
When selecting a thermal solution for your system, please refer to the website below for collection of
heatsinks evaluated and recommended by Intel for use with Intel processors. Note, those heatsinks are
recommended for maintaining the specified Maximum T case requirement. In addition, this collection
is not intended to be a comprehensive listing of all heatsinks that support Intel processors.

For vendor list of heatsink and fan, please visit :
http://developer.intel.com/design/Pentium4/components/index

ii

Chapter 1

Introduction of 865GDA/865GDAP/ 865PEDA/865PEDAP

Motherboard

1-1 Feature of motherboard

The 865GDA/ 865GDAP/ 865PEDA /865PEDAP motherboard is design for use Intel
Pentium 4 Processor in 478 Pin Package/Northwood/Hyper Threading Processor with the Intel
865G/865PE Chipset delivers a high performance and professional desktop platform solution.
Which utilize the Socket 478 design and the memory size expandable to 2.0GB.

These motherboards use the newest Intel 865G/865PE Chipset Supports 800/533/400MHz
System Bus in data transfer rate, these motherboards provided 200/166/133MHz SDRAM
clock frequency support DDR400/DDR333/DDR266 SDRAM. These motherboards also
provided Dual Channel function to increase memory performance. The motherboard
embedded ICH5 chipset offers two parallel ULTRA ATA 100 interface and two serial ATA
interface to provide speedier HDD throughout that boosts overall system performance.

865GDA/865GDAP with integrated 2D/3D Graphics Accelerator which supports 256 bit
graphics core, and supports hardware motion compensation assist for software MPEG/DVD
decode, makes this board lower cost alternative to a video card. For those wanting even
greater graphic performance, an AGP 4X slot is included on the board (For 1.5V AGP card
only. No for 3.3V or Universal AGP card). This AGP slot will support either a 4X/8X VGA
card.

The 865GDAP/ 865PEDAP motherboard including Fast Ethernet PCI controller chip support
10Mb/s, 100Mb/s Base transfer rate.

These motherboards also has an integrated 6-channel AC97’ CODEC chip on board support
6-channel 3D surround positioning Audio which is fully compatible with Sound Blaster Pro
that gives you the best sound quality and compatibility.

With USB control as well as capability of expanding to eight USB2.0 function ports, these
motherboards meet future USB demand also these motherboards have built-in hardware
monitor function. This will monitor and protect your computer. These motherboards special
design in hardware to protect BIOS from virus crash BIOS data.

These motherboards provide special function in BIOS Setup to setting CPU Host clock step
by step increasing let users to approach over clocking.

These motherboards provided high performance & meet future specification demand. It is
really wise choice for your computer.

1

1-2 Specification

Spec Description

ATX form factor 4 layers PCB size: 30.5x22.0cm

Design
Chipset

CPU Socket

(mPGA478B Socket)

Memory Socket

Expansion Slot &
Headers

Integrate IDE

Integrate Serial ATA

LAN On Board

Audio

BIOS
Multi I/O

∗

Intel 865G Graphics Memory Controller Hub (GMCH) Chipset

∗

for 865GDA/865GDAP

Intel 865PE Memory Controller Hub (MCH) Chipset for

∗

865PEDA/865PEDAP

Intel 82801EB I/O Controller Hub (ICH5) Chipset

∗

Support Intel Pentium 4 478 Pin package utilizes Flip-Chip Pin

∗

Grid Array (FC-PGA2) package processor

Support CPU Frequency 400MHz/533MHz/800MHz

∗

Support 1.6G∼3.2G 478 Pin Pentium 4 processor

∗

Reserves support for future Intel Pentium 4 processors

∗

184-pin DDR SDRAM module socket x2

∗

Support Dual channel DDR266/DDR333/DDR400 DDR

∗

SDRAM
Expandable to 2.0GB

∗

AGP slot x1 for AGP 0.8V/1.5V standard only, support AGP

∗

2.0/3.0 & 4X/8X mode
32-bit PCI slot x 5, CNR slot x 1

∗

Two IDE controllers support PCI Bus Mastering, ATA

∗

PIO/DMA and the ULTRA DMA 33/66/100 functions that
deliver the data transfer rate up to 100 MB/s
Two Serial ATA Host controllers, that deliver the data transfer

∗

rate up to 150 MB/s
VIA VT6105 LOM PCI LAN controller chip

∗

Supports 10/100 Mb/sec data transfer rate

∗

Realtek ALC 6-channel AC97’ Codec integrated

∗

Support 6-channel 3D surround & Positioning Audio

∗

Audio driver and utility included

∗

Award 4Mb Flash ROM

∗

PS/2 keyboard and PS/2 mouse connectors

∗

Floppy disk drive connector x1

∗

Parallel port x1, Serial port x2

∗

USB 2.0 connector x6, headers x2 (connecting cable option)

∗

Audio connector Line-in, Line-out, MIC & Game Port header

∗

2

1-3 Performance List

The following performance data list is the testing result of some popular benchmark testing
programs. These data are just referred by users, and there is no responsibility for different
testing data values gotten by users (the different Hardware & Software configuration will
result in different benchmark testing results.)

Performance Test Report

CPU:
DRAM:
On Board VGA:
Hard Disk Driver:
BIOS:
OS:

Intel Pentium 4 2.53GHz (533MHz FSB)/3GHZ (800MHz FSB) mPGAB package

512MB DDR400 SDRAM x2 (KINGSTON D328DW)

1024x768x32bit Color

IBM IC35L040AVVN07-0 (ATA-100 7200RPM)

Award Optimal default

Win XP Professional (Service Pack 1)

2.53GHz
133/133

3GHz

200/200

3GHz 200/200

Dual Channel

3GHz 200/200

Dual Channel

Hyper-Threading

3D Mark 2001SE 2192 2506 2967 2929
3D Mark 2003 59 70 94 92
3D Winbench 2000 (32/32BIT) 73.2 78.3 83.3 83.1
PC Mark 2002
CPU/Memory/HDD 6146/5410/879 7336/6480/879 7364/7620/879 7380/7632/877
Content Creation Winstone 2002 41 48.9 51.7 46.4
Content Creation Winstone 2003 41.9 49.6 51.7 50.1
Business Winstone 2002 29.4 33.3 33.7 33.1
Winbench 99 V1.2:
Business Disk Winmark99 8600 8840 9190 9180
Hi-end Disk Winmark99 32200 31700 31800 32900
Business Graphic Winmark 164 205 226 277
Hi-end Graphic Winmark 591 852 874 898
SYS Mark 2001/2002 : SISMark 2001/2002 Rating (Internet Content Creation / Office Productivity)
SISMark 2001 236 (263/212) 278 (314/247) 286 (325/251) 271 (317/231)
SISMark 2002 in Windows XP 245 (346/173) 283 (411/195) 300 (429/210) 316 (436/229)
SISOFT Sandra 2003 :
Dhrystone ALU MIPS 6778 7712 7743 9183
Whetstone FPU iSSE2 MFLOPS 1407/3114 1711/3944 1708/3942 2601/5416
RAM Int Buffered iSSE2 MB/S 2204 2688 4226 4266
RAM Float Buffered iSSE2 MB/S 2204 2689 4227 4263
Integer SSE2 IT/S 10033 11923 11925 11749
Floating-Point SSE2 IT/S 12768 15177 15178 21590
QUAKE3 DEMO1 FPS 110.9 125.6 134.1 134.5
DEMO2 FPS 110.5 127.3 136.3 135.9
Return to Castle Wolfenstein FPS 74.4 84.5 88.6 88.9
WCPUID System / CPU Clock 132.98/2526.62 199.66/2995.70 199.71/2995.70 199.71/2995.70

3

/

r

_

1-4 Layout Diagram & Jumper Setting

PRINT LAN

MIC

PS/2 Mouse

PS/2 Keyboard

ATX 12V Power Connector

PS2 KB/Mouse Port

K/B Power ON Jumper

PC99 Back Panel

COM

(for 865GDA/865GDAP)

USB Port (USB1)

USB Power ON Jumpe

LAN Connector

Audio Connector (CN1)

Front Panel Audio

6-CH AC’97 Audio Codec

(JP1)

2 Connector

(JP2)

USB Port

CD Audio

LINE-IN

LINE-OUT

COM1

VGA/COM2

USB1

USB

(Option)

VGA (for 865GDA/865GDAP)
COM2 (for 865PEDA/865PEDAP)

CPU Socket

CPU FAN

ATX Power Connector

DDR DIMMx2

Intel 865G/865PE Chip
Floppy Connector

SYSFAN1

AGP 4X/8X 1.5V Slot

SPDIF Connector

PCI Slot

ITE 8712 I/O Chip

GAME Port Connector

4MBit FWH BIOS

CNR Slot

IR Connector

Wake On LAN

USB Port

(JUSB1, JUSB2, USB2)

Intel 82801EB Chip

ATA 100 IDE Connector

Serial-ATA Connector
(SATA1, 2)

Clear CMOS (JP3)

Speak Connector

Front Panel Connector

SYSFAN2

4

Jumpers

Jumper Name Description Page

JP3 CMOS RAM Clear 3-pin Block P.6
JP1 Keyboard Power On Enable/Disabled 3-pin Block P.7
JP2 USB Power On Enable/Disabled 3-pin Block P.7

Connectors

Connector Name Description Page

ATXPWR ATX Power Connector 20-pin Block P.11
ATX12V1 ATX 12V Power Connector 4-pin Block P.12
USB1, UL_B USB Port Connector 4-pin Connector P.12

LAN

(for 865GDAP/865PEDAP)

KB
(PS2 KB/MOUSE)
PARALLEL Parallel Port Connector 25-pin Female P.12
CN1 Audio Line In/Out MIC Connector 3 phone jack Connector P.12

VGA
(for 865GDA/865GDAP)

COM1 Serial Port COM1 Connector 9-pin Connector P.12

COM2

(for 865PEDA/865PEDAP)

FDD Floppy Driver Connector 34-pin Block P.13
IDE1/IDE2 Primary/Secondary 40-pin Block P.13
SATA1, SATA2 Serial-ATA Port Connector 7-pin Block P.14

Only for 865GDA/865GDAP

LAN Connectors RJ-45 Connector P.12

PS/2 Mouse & PS/2 Keyboard

6-pin Female P.12

Connector

VGA Display Connector 15-pin Female Connector P.12

Serial Port COM2 Connector 9-pin Connector P.12

Headers

Header Name Description Page

AUDIO Line-Out, MIC Headers 9-pin Block P.14
USB2, JUSB1, JUSB2 USB Port Headers 9-pin Block P.14

COM_2

Serial Port COM2 headers 9-pin Block P.15

(for 865GDA/865GDAP)

SPEAK Speaker connector 4-pin Block P.15
JW_FP
(Power LED/Reset/
IDE LED/ Power Button)

Front Panel Header
(including Power LED/ IDE activity LED/
Reset switch / Power On Button lead)

9-pin Block P.15

WOL Wake On-LAN Headers 3-pin Block P.15
SYSFAN1, SYSFAN2,

FAN Speed Headers 3-pin Block P.16
CPUFAN
IR IR infrared module Headers 5-pin Block P.16
CDIN CD Audio-In Headers 4-pin Block P.17
GAME Game Port Headers 15-pin Block P.17
SPDIF SPDIF In/Out Headers 9-pin Block

P.17

Expansion Sockets

Socket/Slot Name Description Page

ZIF Socket 478 CPU Socket 478-pin mPGAB CPU Socket P.8
DIMM1, DIMM2 DDR Module Socket 184-pin DDR SDRAM Module

Expansion Socket

PCI1 ∼ PCI5 PCI Slot 32-bit PCI Local Bus Expansion slots P.9
AGP AGP 4X/8X Mode Slot AGP Expansion Slot P.11
CNR CNR Slot Communication Network Riser slots

P.8

5

Chapter 2

Hardware installation

2-1 Hardware installation Steps

Before using your computer, you had better complete the following steps:

1. Check motherboard jumper setting

2. Install CPU and Fan

3. Install System Memory (DIMM)

4. Install Expansion cards

5. Connect IDE and Floppy cables, Front Panel /Back Panel cable

6. Connect ATX Power cable

7. Power-On and Load Standard Default

8. Reboot

9. Install Operating System

10. Install Driver and Utility

2-2 Checking Motherboard’s Jumper Setting

(1) CMOS RAM Clear (3-pin) : JP3

A battery must be used to retain the motherboard configuration in CMOS RAM short 1-2
pins of JP3 to store the CMOS data.

To clear the CMOS, follow the procedure below:

1. Turn off the system and unplug the AC power

2. Remove ATX power cable from ATX power connector

3. Locate JP3 and short pins 2-3 for a few seconds

4. Return JP3 to its normal setting by shorting pins 1-2

5. Connect ATX power cable back to ATX power connector

Note: When should clear CMOS

1. Troubleshooting

2. Forget password

3. After over clocking system boot fail

13

JP3

1-2 closed Normal (Default)

CMOS RAM Clear Setting

1 3

JP3

2-3 closed Clear CMOS

6

(2) Keyboard/USB Power On function Enabled/Disabled: JP1/JP2

When setting Enabled you can using keyboard by key in password/USB device to power
on system.

JP1

JP1

JP1 1-2 closed K/B Power ON Disabled (Default)

1

3

1

JP1 2-3 closed K/B Power ON Enabled

3

JP2

JP2

JP2 1-2 closed USB Wake-Up Disabled (Default)

1

3

1

JP2 2-3 closed USB Wake-Up Enabled

3

2-3 Install CPU

2-3-1 Glossary

Chipset (or core logic) - two or more integrated circuits which control the interfaces between
the system processor, RAM, I/O devises, and adapter cards.
Processor slot/socket - the slot or socket used to mount the system processor on the
motherboard.

Slot (AGP, PCI, ISA, RAM) - the slots used to mount adapter cards and system RAM.
AGP - Accelerated Graphics Port - a high speed interface for video cards; runs at 1X

(66MHz), 2X (133MHz), or 4X (266MHz).
PCI - Peripheral Component Interconnect - a high speed interface for video cards, sound
cards, network interface cards, and modems; runs at 33MHz.
ISA - Industry Standard Architecture - a relatively low speed interface primarily used for
sound cards and modems; runs at approx. 8MHz.

Serial Port - a low speed interface typically used for mouse and external modems.
Parallel Port - a low speed interface typically used for printers.
PS/2 - a low speed interface used for mouse and keyboards.
USB - Universal Serial Bus - a medium speed interface typically used for mouse, keyboards,

scanners, and some digital cameras.
Sound (interface) - the interface between the sound card or integrated sound connectors and
speakers, MIC, game controllers, and MIDI sound devices.

LAN (interface) - Local Area Network - the interface to your local area network.
BIOS (Basic Input/Output System) - the program logic used to boot up a computer and

establish the relationship between the various components.
Driver - software, which defines the characteristics of a device for use by another device or
other software.
Processor - the "central processing unit" (CPU); the principal integrated circuit used for doing
the "computing" in "personal computer"

Front Side Bus Frequency -

by the clock generator for CPU, DRAM and PCI BUS.

CPU L2 Cache -

the flash memory inside the CPU, normally Athlon CPU has 256K or above,

while Duron will have 64K.

the working frequency of the motherboard, which is generated

2-3-2 About Intel Pentium 4 478-pin CPU

7

This motherboard provides a 478-pin surface mount, Zero Insertion Force (ZIF) socket,
referred to as the mPGA478B socket supports Intel Pentium 4 processor in the 478 Pin
package utilizes Flip-Chip Pin Grid Array (FC-PGA2) package technology.

The CPU that comes with the motherboard should have a cooling FAN attached to prevent
overheating. If this is not the case, then purchase a correct cooling FAN before you turn on
your system.

WARNING!

Be sure that there is sufficient air circulation across the processor’s heatsink and
CPU cooling FAN is working correctly, otherwise it may cause the processor and
motherboard overheat and damage, you may install an auxiliary cooling FAN, if
necessary.

To install a CPU, first turn off your system and remove its cover. Locate the ZIF socket and
open it by first pulling the level sideways away from the socket then upward to a 90-degree
angle. Insert the CPU with the correct orientation as shown below. The notched corner
should point toward the end of the level. Because the CPU has a corner pin for two of the
four corners, the CPU will only fit in the orientation as shown.

mPGA478B

CPU ZIF mPGAB Socket

Colden Arrow

When you put the CPU into the ZIF socket. No force require to insert of the CPU, then press
the level to Locate position slightly without any extra force.

2-4 Install Memory

This motherboard provides two 184-pin DUAL INLINE MEMORY MODULES (DIMM)
sites for memory expansion available from minimum memory size of 64MB to maximum
memory size of 2.0GB DDR SDRAM.

Valid Memory Configurations

Bank 184-Pin DIMM PCS Total Memory

Bank 0, 1 (DIMM1) DDRDDR266/DDR333/DDR400

DDR SDRAM Module

Bank 2, 3 (DIMM2) DDRDDR266/DDR333/DDR400

DDR SDRAM Module

For Dual channel Limited!

8

X1

X1

64MB∼1.0GB

64MB∼1.0GB

1.

Dual channel function only supports when 2 DIMM Modules plug in both DIMM1 &
DIMM2.

2.

DIMM1 & DIMM2 must be the same type, same size, same frequency for dual channel
function.

Generally, installing DDR SDRAM modules to your motherboard is very easy, you can refer
to figure 2-4 to see what a 184-Pin DDR266/DDR333/DDR400 DDR SDRAM module looks
like.

DI MM2 (BANK2 + BANK3)

DI MM1 (BANK0 + BANK1)

Figure 2-4

NOTE!

When you install DIMM module fully into the DIMM socket the eject tab should be
locked into the DIMM module very firmly and fit into its indention on both sides.

WARNING!

For the DDR SDRAM CLOCK is set at 200MHz, use only DDR400-compliant DDR
Modules. When this motherboard operate at 200Mhz, most system will not even
boot if non-compliant modules are used because of the strict timing issues, if your
SDR Modules are not DDR400-compliant, set the DDR SDRAM clock to 133MHz
to ensure system stability.

2-5 Expansion Cards

WARNING!

2-5-1 Procedure For Expansion Card Installation

1. Read the documentation for your expansion card and make any necessary hardware or
software setting for your expansion card such as jumpers.

2. Remove your computer’s cover and the bracket plate on the slot you intend to use.

3. Align the card’s connectors and press firmly.

4. Secure the card on the slot with the screen you remove above.

5. Replace the computer system’s cover.

6. Set up the BIOS if necessary.

7. Install the necessary software driver for your expansion card.

Turn off your power when adding or removing expansion cards or other system
components. Failure to do so may cause severe damage to both your motherboard
and expansion cards.

2-5-2 Assigning IRQs For Expansion Card

Some expansion cards need an IRQ to operate. Generally, an IRQ must exclusively assign to
one use. In a standard design, there are 16 IRQs available but most of them are already in use.

9

Standard Interrupt Assignments

IRQ Priority Standard function

0 N/A System Timer
1 N/A Keyboard Controller
2 N/A Programmable Interrupt
3 * 8 Communications Port (COM2)
4 * 9 Communications Port (COM1)
5 * 6 Sound Card (sometimes LPT2)
6 * 11 Floppy Disk Controller
7 * 7 Printer Port (LPT1)
8 N/A System CMOS/Real Time Clock

9 * 10 ACPI Mode when enabled
10 * 3 IRQ Holder for PCI Steering
11 * 2 IRQ Holder for PCI Steering
12 * 4 PS/2 Compatible Mouse Port
13 N/A Numeric Data Processor
14 * 5 Primary IDE Channel
15 * 1 Secondary IDE Channel

* These IRQs are usually available for ISA or PCI devices.

2-5-3 Interrupt Request Table For This Motherboard

Interrupt request are shared as shown the table below:

INT A INT B INT C INT D INT E INT F INT G INT H
Slot 1
Slot 2
Slot 3
Slot 4
Slot 5
Onboard VGA
Onboard LAN
Onboard USB 1
Onboard USB 2
Onboard USB 3
Sound

IMPORTANT!

√

√

If using PCI cards on shared slots, make sure that the drivers support “Shared
IRQ” or that the cards don’t need IRQ assignments. Conflicts will arise between
the two PCI groups that will make the system unstable or cards inoperable.

√

√

√

√

√

√

√

√

√

2-5-4 AGP Slot

This motherboard provides an AGP Slot, only support the 1.5V 4X/0.8V 8X AGP VGA card.
Do not use AGP 2X card (3.3V) in this motherboard. It will burn and damage the motherboard due to
Intel® 865 chipset can not support AGP 2X (3.3V).

10

IMPORTANT!

Before you plug-in AGP card, please make sure the following notice is fully
understood and practiced. If your AGP card has “AGP 4X notch (show
below) please make sure your AGP card is AGP 4X/8X (1.5V/0.8V) not AGP
2X (3.3V)

2x notch 4x notch

Example 1:

SiS 305 & ATi Rage 128 Pro AGP card those golden finger is compatible with

AGP SLOT

2X/4X mode AGP slot, but only can support 2X (3.3V) only. If you install these
cards in Intel® 865 based motherboard it will burn and damage the motherboard.

Example 2:

We also find Diamond Vipper V770 golden finger is design for 2X/4X mode AGP

Slot. It can be adjusted the jumper for AGP 2X (3.3V) or AGP 4X (1.5V). But the
factory default setting is 2X (3.3V). If you install this AGP card in motherboard
without change the jumper setting to 4X (1.5V), it will burn the motherboard.

2-6 Connectors, Headers

2-6-1 Connectors

(1) Power Connector (20-pin block) : ATXPWR

ATX Power Supply connector. This is a new defined 20-pins connector that usually comes

with ATX case. The ATX Power Supply allows to use soft power on momentary switch that
connect from the front panel switch to 2-pins Power On jumper pole on the motherboard.
When the power switch on the back of the ATX power supply turned on, the full power will not
come into the system board until the front panel switch is momentarily pressed. Press this
switch again will turn off the power to the system board.

PIN ROW2 ROW1
1 3.3V 3.3V
2 -12V 3.3V
3 GND GND
4 Soft Power On 5V
5 GND GND
6 GND 5V
7 GND GND
8 -5V Power OK
9 +5V +5V (for Soft Logic)
10 +5V +12V

Pin 1

(2) ATX 12V Power Connector (4-pin block) : ATX12V1

This is a new defined 4-pins connector that usually comes with ATX Power Supply. The ATX

Power Supply which fully support Pentium 4 processor must including this connector for
support extra 12V voltage to maintain system power consumption. Without this connector
might cause system unstable because the power supply can not provide sufficient current for
system.

11

Pin 1

(3) USB Port connector: USB1, UL_B (USB)

The connectors are 4-pin connector that connect USB devices to the system board.

(4) LAN Port connector: LAN (for 865GDAP/865PEDAP)

This connector is standard RJ45 connector for Network connector.

(5) PS/2 Mouse & PS/2 Keyboard Connector: KB (PS2 KB/MOUSE)

The connectors for PS/2 keyboard and PS/2 Mouse.

(6) Parallel Port Connector (25-pin female): PARALLEL

Parallel Port connector is a 25-pin D-Subminiature Receptacle connector. The On-board
Parallel Port can be disabled through the BIOS SETUP. Please refer to Chapter 3
“INTEGRATED PERIPHERALS SETUP” section for more detail information.

(7) Audio Line-In, Lin-Out, MIC Connector : CN1

This Connector are 3 phone Jack for LINE-OUT, LINE-IN, MIC

Line-out :
Line-in :

Audio input to sound chip

MIC :

Audio output to speaker

Microphone Connector

(8) VGA Connector (15-pin D-Sub) Connector: VGA (for 865GDA/865GDAP only)

VGA is the 15-pin D-Subminiature female connector for display monitor.

(9) Serial Port COM1/COM2: COM1/COM2 (COM2 only for 865PEDA/865PEDAP)

COM1/COM2A is the 9-pin D-Subminiature mail connector. The On-board serial port can be
disabled through BIOS SETUP. Please refer to Chapter 3 “INTEGRATED PERIPHERALS
SETUP” section for more detail information.

USB1PS/2 Mouse PRINT

LAN

MIC

LINE-IN

LINE-OUT

PS/2 Keyboard USB

(10) Floppy drive Connector (34-pin block): FDD

This connector supports the provided floppy drive ribbon cable. After connecting the single
plug end to motherboard, connect the two plugs at other end to the floppy drives.

COM1

12

VGA/COM2

(Option)

FDD

Pin 1

Floppy Drive Connector

(11) Primary IDE Connector (40-pin block): IDE1

This connector supports the provided IDE hard disk ribbon cable. After connecting the

single plug end to motherboard, connect the two plugs at other end to your hard disk(s). If
you install two hard disks, you must configure the second drive to Slave mode by setting its
jumpers accordingly. Please refer to the documentation of your hard disk for the jumper
settings.

(12) Secondary IDE Connector (40-pin block): IDE2

This connector connects to the next set of Master and Slave hard disks. Follow the same

procedure described for the primary IDE connector. You may also configure two hard
disks to be both Masters using one ribbon cable on the primary IDE connector and another
ribbon cable on the secondary IDE connector.

IDE1

Two hard disks can be connected to each connector. The first HDD is referred to as the

•

Pin 1

Pin 1

IDE2

“Master” and the second HDD is referred to as the “Slave”.

For performance issues, we strongly suggest you don’t install a CD-ROM or DVD-ROM

•

drive on the same IDE channel as a hard disk. Otherwise, the system performance on this
channel may drop.

(13) Serial-ATA Port connector: SATA1/SATA2

This connector support the provided Serial ATA IDE hard disk cable to connecting the
motherboard and serial ATA hard disk.

13

A

SATA2

SATA1

Pin 1

On Chip Serial ATA

Serial-ATA Port Connector

2-6-2 Headers

(1) Line-Out, MIC Header (9-pin): AUDIO

This header connect to Front Panel Line-out, MIC connector with cable.

UDI O

Pin 1

910

2

AUD-GND

AUD-VCC

AUD-RET-R

AUD-RET-L

AUD-MIC

AUD-MIC-BI AS

AUD-FPOUT-R

HP-ON

AUD-FPOUT-L

Line-Out, MIC Headers

(2) USB Port Connector/Headers (9-pin) : JUSB1, JUSB2/ USB2

The JUSB1, JUSB2 is for internal connecting USB device directly. The USB2 header is
used for connecting the additional USB port plug. By attaching an option USB cable,
your can be provided with two additional USB plugs affixed to the back panel.

OC

VCC

GND

DATA

-

+ DATA

VCC

GND

DATA

-

+ DATA

USB Port Headers

USB2

Pin 1

JUSB2JUSB1

(3) Serial Port2 COM2 Header (9-pin) : COM_2 (only for 865GDA/865GDAP)

14

N

Pin 1

COM_2

ote: Orient the read marking on the

COM2 ribbon cable to pin 1

Serial Port2 COM2 Header

(4) IDE Activity LED: IDE LED

This connector connects to the hard disk activity indicator light on the case.

(5) Reset switch lead: RESET

This 2-pin connector connects to the case-mounted reset switch for rebooting your computer
without having to turn off your power switch. This is a preferred method of rebooting in order
to prolong the lift of the system’s power supply. See the figure below.

(6) Speaker connector: SPEAK

This 4-pin connector connects to the case-mounted speaker. See the figure below.

(7) Power LED: PWR-LED

The Power LED is light on while the system power is on. Connect the Power LED
from the system case to this pin.

(8) Power switch: PWR BTN

This 2-pin connector connects to the case-mounted power switch to power ON/OFF the
system.

PWRBTN

ACPI LED

GND

VCC5

ACPI LED

PWRBT N

NC

GND

VCC5

RST S W

HDDLED

RESET

HDLED

Pin 1

NC

GND

VCC5

SPKR

System Case Connections

JW_FPSPEAK

Pi n 1

(9) Wake On-LAN Headers (3-pin) : WOL

This connector connects to a LAN card with a WAKE ON-LAN output. This connector
power up the system when a wake up signal is received through the LAN card.

NOTE:

This feature requires that Wake On LAN or Ring In Wake up is enabled.

15

5VSB

GND

WOL

WOL

13

Wake-On-LAN Headers

(10) FAN Speed Headers (3-pin) : SYSFAN1, SYSFAN2, CPUFAN

These connectors support cooling fans of 350mA (4.2 Watts) or less, depending on the
fan manufacturer, the wire and plug may be different. The red wire should be positive,
while the black should be ground. Connect the fan’s plug to the board taking into
consideration the polarity of connector.

CPUFAN

SYSFAN1

SYSFAN2

13

13

13

FAN Headers

(11) IR infrared module Headers (5-pin) : IR

This connector supports the optional wireless transmitting and receiving infrared
module. You must configure the setting through the BIOS setup to use the IR function.

Pin 1

IR

GND

IRRX

2

6

5

NC

IRTX

VCC5

IR infrared module Headers

16

-

-

(12) CD Audio-In Headers (4-pin) : CDIN

CDIN are the connectors for CD-Audio Input signal. Please connect it to CD-ROM
CD-Audio output connector.

4

CDI N

1

CD Audio-In Headers

(13) Game Port Header: GAME

Pin 1

GAME Port Headers

(14) SPDIF-Bracket Connector : SPDIF

The connector allows you to connect a SPDIF-Bracket for Sony & Philips Digital
Interface (SPDIF). The SPDIF-Bracket offers 2 SPDIF jacks for digital audio
transmission and receiver (for optional optical fiber) and 2 analog Line-Out jacks for 4­channel audio output.

To attach the fiber-optic cable to optical SPDIF jack, you have to remove the plug from
the jack first.

SPDIF

Pin 1

SPDIF-Bracket Connector

OUT

NC

SPDIF

GENT ER

GND

GND

210

9

L

12V

BASS

SPDIF-I N

SURROUND

SURROUND-R

Connect to SPDIF

(Option)

17

2-7 Starting Up Your Computer

1. After all connection are made, close your computer case cover.

2. Be sure all the switch are off, and check that the power supply input voltage is set to
proper position, usually in-put voltage is 220V∼240V or 110V∼120V depending on your
country’s voltage used.

3. Connect the power supply cord into the power supply located on the back of your system
case according to your system user’s manual.

4. Turn on your peripheral as following order:

a. Your monitor.
b. Other external peripheral (Printer, Scanner, External Modem etc…)
c. Your system power. For ATX power supplies, you need to turn on the power supply

and press the ATX power switch on the front side of the case.

5. The power LED on the front panel of the system case will light. The LED on the monitor
may light up or switch between orange and green after the system is on. If it complies
with green standards or if it is has a power standby feature. The system will then run
power-on test. While the test are running, the BIOS will alarm beeps or additional
message will appear on the screen.

If you do not see any thing within 30 seconds from the time you turn on the power. The
system may have failed on power-on test. Recheck your jumper settings and connections
or call your retailer for assistance.

Beep Meaning

One short beep when displaying logo No error during POST

Long beeps in an endless loop No DRAM install or detected

One long beep followed by three short
beeps

High frequency beeps when system is
working

Video card not found or video card memory
bad

CPU overheated

System running at a lower frequency

6. During power-on, press <Delete> key to enter BIOS setup. Follow the instructions in
BIOS SETUP.

7.

Power off your computer:

You must first exit or shut down your operating system
before switch off the power switch. For ATX power supply, you can press ATX power
switching after exiting or shutting down your operating system. If you use Windows 9X,
click

“Start”

button, click

“Shut down”

and then click

“Shut down the computer?”

The power supply should turn off after windows shut down.

18

Chapter 3

Introducing BIOS

The BIOS is a program located on a Flash Memory on the motherboard. This program is a
bridge between motherboard and operating system. When you start the computer, the BIOS
program gain control. The BIOS first operates an auto-diagnostic test called POST (power on
self test) for all the necessary hardware, it detects the entire hardware device and configures
the parameters of the hardware synchronization. Only when these tasks are completed done it
gives up control of the computer to operating system (OS). Since the BIOS is the only
channel for hardware and software to communicate, it is the key factor for system stability,
and in ensuring that your system performance as its best.

In the BIOS Setup main menu of Figure 3-1, you can see several options. We will explain
these options step by step in the following pages of this chapter, but let us first see a short
description of the function keys you may use here:

Press <Esc> to quit the BIOS Setup.

•

Press

•

↑↓←→

confirm or to modify.
Press <F10> when you have completed the setup of BIOS parameters to save these

•

parameters and to exit the BIOS Setup menu.
Press Page Up/Page Down or +/– keys when you want to modify the BIOS parameters for

•

the active option.

(up, down, left, right) to choose, in the main menu, the option you want to

3-1 Entering Setup

Power on the computer and by pressing <Del> immediately allows you to enter Setup.
If the message disappears before your respond and you still wish to enter Setup, restart the
system to try again by turning it OFF then ON or pressing the “RESET” button on the system
case. You may also restart by simultaneously pressing <Ctrl>, <Alt> and <Delete> keys. If
you do not press the keys at the correct time and the system does not boot, an error message
will be displayed and you will again be asked to

Press <F1> to continue, <Ctrl-Alt-Esc> or <Del> to enter Setup

3-2 Getting Help

Main Menu

The on-line description of the highlighted setup function is displayed at the bottom of the
screen.

Status Page Setup Menu/Option Page Setup Menu

Press F1 to pop up a small help window that describes the appropriate keys to use and the
possible selections for the highlighted item. To exit the Help Window, press <Esc>.

19

3-3 The Main Menu

Once you enter Award BIOS CMOS Setup Utility, the Main Menu (Figure 3-1) will appear
on the screen. The Main Menu allows you to select from fourteen setup functions and two
exit choices. Use arrow keys to select among the items and press <Enter> to accept or enter
the sub-menu.

CMOS Setup Utility – Copyright(C) 1984-2003 Award Software

Standard CMOS Features

Advanced BIOS Features

Advanced Chipset Features

Integrated Peripherals

Power Management Setup

PnP/PCI Configurations

PC Health Status

Esc : Quit

F10 : Save & Exit Setup

Time, Date, Hard Disk Type...

Figure 3-1

Miscellaneous Control

Load optimized Defaults

Load Standard Defaults

Set Supervisor Password

Set User Password

Save & Exit Setup

Exit Without Saving

↑↓→←

: Select Item

Standard CMOS Features

Use this Menu for basic system configurations.

Advanced BIOS Features

Use this menu to set the Advanced Features available on your system.

Advanced Chipset Features

Use this menu to change the values in the chipset registers and optimize your system’s
performance.

Integrated Peripherals

Use this menu to specify your settings for integrated peripherals.

Power Management Setup

Use this menu to specify your settings for power management.

PnP/PCI configurations

This entry appears if your system supports PnP/PCI.

PC Health Status

This entry shows your PC health status.

Miscellaneous Control

Use this menu to specify your settings for Miscellaneous control.

20

Load Optimized Defaults

Use this menu to load the BIOS default values that are settings for optimal performances
system operations.

Load Standard Defaults

Use this menu to load the BIOS default values that are factory settings for the stable
performance system operation.

Set Supervisor/User Password

Use this menu to set User and Supervisor Passwords.

Save & Exit Setup

Save CMOS value changes to CMOS and exit setup.

Exit Without Saving

Abandon all CMOS value changes and exit setup.

3-4 Standard CMOS Features

The items in Standard CMOS Setup Menu are divided into several categories. Each category
includes no, one or more than one setup items. Use the arrow keys to highlight the item and
then use the <PgUp> or <PgDn> keys to select the value you want in each item.

CMOS Setup Utility – Copyright(C) 1984-2003 Award Software

Standard CMOS Features

Date (mm:dd:yy) Wed, May, 14 2003
Time (hh:mm:ss) 11 : 02 : 35

> IDE Primary Master Press Enter None
> IDE Primary Slave Press Enter None
> IDE Secondary Master Press Enter None
> IDE Secondary Slave Press Enter None

Drive A 1.44M, 3.5 in.
Drive B None

Video EGA/VGA
Halt On All,But Keyboard

Base Memory 640K
Extended Memory 56320K
Total Memory 57344K

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

Item Help

Menu Level >

Change the day, month,
year and century

Date

The date format is <day><month><date><year>.

Day of the week, from Sun to Sat, determined by BIOS. Read-only.

Day
Month
Date
Year

The month from Jan. through Dec.

The date from 1 to 31 can be keyed by numeric function keys.

The year depends on the year of the BIOS.

Time

21

The time format is <hour><minute><second>.

Primary Master/Primary Slave
Secondary Master/Secondary Slave

Press PgUp/<+> or PgDn/<–> to select Manual, None, Auto type. Note that the specifications of
your drive must match with the drive table. The hard disk will not work properly if you enter
improper information for this category. If your hard disk drive type is not matched or listed, you
can use Manual to define your own drive type manually.

If you select Manual, related information is asked to be entered to the following items. Enter the
information directly from the keyboard. This information should be provided in the
documentation from your hard disk vendor or the system manufacturer.
If the controller of HDD interface is SCSI, the selection shall be “None”.
If the controller of HDD interface is CD-ROM, the selection shall be “None”

Access Mode
Cylinder
Head
Precomp
Landing Zone
Sector

number of sectors

The settings are Auto Normal, Large, and LBA.

number of cylinders

number of heads

write precomp

landing zone

3-5 Advanced BIOS Features

CMOS Setup Utility – Copyright(C) 1984-2003 Award Software

Advanced BIOS Features

Anti-Virus Protection Disabled
Cooling Sprite Disabled
CPU L1 & L2 Cache Enabled
Hyper Threading Technology Disabled
Quick Power On Self Test Enabled
HDD Boot Sprite Disabled
Hard Disk Boot Priority Press Enter
First Boot Device Floppy
Second Boot Device HDD 0
Third Boot Device CDROM
Boot other Device Enabled
Swap Floppy Drive Disabled
Boot Up Floppy Seek Enabled
Boot Up NumLock Status On
Gate A20 Option Fast
Typematic Rate Setting Disabled
Typematic Rate (Chars/Sec) 6
Typematic Delay (Msec) 250
Security Option Setup
APIC Mode Disabled
MPS Version Control For OS 1.4
OS Select For DRAM > 64MB Non-OS2
Report NO FDD For Windows Yes
Intel OSB Logo Show Disabled

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

Item Help

Menu Level >

Anti-Virus Protection

22

Allows you to choose the VIRUS Warning feature for IDE Hard Disk boot sector protection.
If this function is enabled and someone attempt to write data into this area, BIOS will show a
warning message on screen and alarm beep.

Disabled

(default) No warning message to appear when anything attempts to access the

boot sector or hard disk partition table.

Enabled

Activates automatically when the system boots up causing a warning
message to appear when anything attempts to access the boot sector of
hard disk partition table.

CPU Internal Cache

The default value is Enabled.

Enabled
Disabled

(default) Enable cache

Disable cache

Note: The internal cache is built in the processor.

External Cache

Choose Enabled or Disabled. This option enables the Level 2 cache memory.

CPU L2 Cache ECC Checking

Choose Enabled or Disabled. This option enables the Level 2 cache memory ECC (error
check correction).

Quick Power On Self Test

This category speeds up Power On Self Test (POST) after you power on the computer. If this
is set to Enabled. BIOS will shorten or skip some check items during POST.

Enabled
Disabled

(default) Enable quick POST

Normal POST

First/Second/Third/Fourth Boot Device

The BIOS attempts to load the operating system from the devices in the sequence selected in
these items. The settings are Floppy, LS/ZIP, HDD-0/HDD-1/HDD-3, SCSI, CDROM, LAD
and Disabled.

Swap Floppy Drive

Switches the floppy disk drives between being designated as A and B. Default is Disabled.

Boot Up Floppy Seek

During POST, BIOS will determine if the floppy disk drive installed is 40 or 80 tracks. 360K
type is 40 tracks while 760K, 1.2M and 1.44M are all 80 tracks.

Boot Up NumLock Status

The default value is On.

(default)

On
Off

Keypad is numeric keys.
Keypad is arrow keys.

Gate A20 Option

Normal

(default) The A20 signal is controlled by port 92 or chipset specific method.

Fast

The A20 signal is controlled by keyboard controller or chipset hardware.

Typematic Rate Setting

23

Keystrokes repeat at a rate determined by the keyboard controller. When enabled, the
typematic rate and typematic delay can be selected. The settings are: Enabled/Disabled.

Typematic Rate (Chars/Sec)

Sets the number of times a second to repeat a keystroke when you hold the key down. The
settings are: 6, 8, 10, 12, 15, 20, 24, and 30.

Typematic Delay (Msec)

Sets the delay time after the key is held down before is begins to repeat the keystroke. The
settings are 250, 500, 750, and 1000.

Security Option

This category allows you to limit access to the system and Setup, or just to Setup.

System

The system will not boot and access to Setup will be denied if the
correct password is not entered at the prompt.

Setup

(default) The system will boot, but access to Setup will be denied if the correct

password is not entered prompt.

OS Select For DRAM > 64MB

Allows OS2 to be used with >64MB or DRAM. Settings are Non-OS/2 (default) and OS2.
Set to OS/2 if using more than 64MB and running OS/2.

3-6 Advanced Chipset Features

The Advanced Chipset Features Setup option is used to change the values of the chipset
registers. These registers control most of the system options in the computer.

CMOS Setup Utility – Copyright(C) 1984-2003 Award Software

Advanced Chipset Features

> DRAM Timing Settings Press Enter
System BIOS Cacheable Enabled
Video BIOS Cacheable Enabled
Memory Hole At 15M-16M Disabled
Delay Transaction Enabled
AGP Transfer Mode Auto
AGP Aperture Size 128MB
On-Chip VGA Enabled
On-Chip Frame Buffer Size 16MB

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

Item Help

Menu Level >

DRAM Timing Settings

Please refer to section 3-6-1

System BIOS Cacheable

Selecting Enabled allows caching of the system BIOS ROM at F0000h-FFFFFh, resulting in
better system performance. However, if any program writes to this memory area, a system
error may result. The settings are: Enabled and Disabled.

Video RAM Cacheable

24

Select Enabled allows caching of the video BIOS, resulting in better system performance.
However, if any program writes to this memory area, a system error may result. The settings
are: Enabled and Disabled.

Memory Hole At 15M-16M

You can reserve this area of system memory for ISA adapter ROM. When this area is
reserved, it cannot be cached. The user information of peripherals that need to use this area of
system memory usually discusses their memory requirements. The settings are: Enabled and
Disabled.

Delay Transaction

The chipset has an embedded 32-bit posted write buffer to support delay transactions cycles.
Select Enabled to support compliance with PCI specification version 2.1. The settings are:
Enabled and Disabled.

AGP Transfer Mode

In this item you can select AGP transfer mode Auto/4X/1X the Default setting is Auto.

3-6-1 DRAM Timing Settings

CMOS Setup Utility – Copyright(C) 1984-2003 Award Software

DRAM Timing Settings

Auto Configuration Standard
SDRAM CAS Latency Time 2.5
SDRAM Cycle Time 7
SDRAM RAS# to CAS# Delay 3
SDRAM RAS# Precharge Time 3

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

SDRAM CAS Latency Time

When synchronous DRAM is installed, the number of clock cycles of CAS latency depends
on the DRAM timing. The settings are: 2T and 2.5T.

Note: Change these settings only if you are familiar with the chipset.

SDRAM RAS# to CAS# Delay

This field let’s you insert a timing delay between the CAS and RAS strobe signals, used when
DRAM is written to, read from, or refreshed. Fast gives faster performance; and Slow gives
more stable performance. This field applies only when synchronous DRAM is installed in the
system. The settings are: 2T, 3T and 4T.

Item Help

Menu Level >>

SDRAM RAS# Precharge Time

If an insufficient number of cycles is allowed for the RAS to accumulate its charge before
DRAM refresh, the refresh may be incomplete and the DRAM may fail to retain date. Fast
gives faster performance; and Slow gives more stable performance. This field applies only
when synchronous DRAM is installed in the system. The settings are: 2T, 3T and 4T.

3-7 Integrated Peripherals

25

CMOS Setup Utility – Copyright(C) 1984-2003 Award Software

Integrated Peripherals

> Onboard IDE Function Press Enter
> Onboard Device Function Press Enter
> Onboard Super IO Function Press Enter
Init Display First PCI Slot
Power On Function Button Only
KB Power On Password Enter
Hot Key Power On Ctrl-F1
Power Loss Function Always Off

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

Item Help

Menu Level >

Onboard IDE Function

Please refer to section 3-7-1

Onboard Device Function

Please refer to section 3-7-2

Onboard Super IO Function

Please refer to section 3-7-3

Init Display First

This item allows you to decide to activate whether PCI Slot or AGP VGA first. The settings
are: PCI Slot, AGP Slot.

3-7-1 Onboard IDE Function

CMOS Setup Utility – Copyright(C) 1984-2003 Award Software

Onboard IDE Function

OnChip Primary PCI IDE Enabled
OnChip Secondary PCI IDE Enabled
Primary Master PIO Auto
Primary Slave PIO Auto
Secondary Master PIO Auto
Secondary Slave PIO Auto
Primary Master UDMA Auto
Primary Slave UDMA Auto
Secondary Master UDMA Auto
Secondary Slave UDMA Auto
IDE 32-bit Transfer Mode Enabled
IDE HDD Block Mode Enabled
Delay For HDD (Secs) 0

Item Help

Menu Level >>

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

OnChip IDE Primary/Secondary

26

The integrated peripheral controller contains an IDE interface with support for two IDE channels.
Select Enabled to activate each channel separately. The settings are: Enabled and Disabled.

Primary/Secondary Master/Slave PIO

The four IDE PIO (Programmed Input/Output) fields let you set a PIO mode (0-4) for each of the
four IDE devices that the onboard IDE interface supports. Modes 0 through 4 provide
successively increased performance. In Auto mode, the system automatically determines the best
mode for each device. The settings are: Auto, Mode 0, Mode 1, Mode 2, Mode 3, Mode 4.

Primary/Secondary Master/Slave UDMA

Ultra DMA/33 implementation is possible only if your IDE hard drive supports it and the
operating environment includes a DMA driver (Windows 95 OSR2 or a third-party IDE bus
master driver). If your hard drive and your system software both support Ultra DMA/33 and Ultra
DMA/66, select Auto to enable BIOS support. The settings are: Auto, Disabled.

IDE HDD Block Mode

Block mode is also called block transfer, multiple commands, or multiple sector read/write. If
your IDE hard drive supports block mode (most new drives do), select Enabled for automatic
detection of the optimal number of block read/writes per sector the drive can support. The
settings are: Enabled, Disabled.

3-7-2 Onboard Device Function

CMOS Setup Utility – Copyright(C) 1984-2003 Award Software

Onboard Device Function

AC97 Audio Auto
AC97 Modem Auto
Game Port Address 201
Midi Port Address
Midi Port IRQ 10

USB Controller Enabled
USB Keyboard Legacy Support Disabled

On-Chip Serial ATA Disabled
Serial ATA Port1 Mode Primary Master

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

AC97 Audio/AC97 Modem

This item is setting on board AC97 Audio/AC97 Modem enabled/disabled. The settings are:
Enabled, Disabled, Auto.

Game Port Address/Midi Port Address

This will determine which Address the Game Port/Midi Port will use.

Item Help

Menu Level >>

USB Controller

Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have a
USB peripherals. The settings are: Enabled, Disabled.

USB Keyboard Legacy Support

27

Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have
a USB keyboard. The settings are: Enabled, Disabled.

On-Chip Serial ATA

The settings are: Disabled, Auto, Combined Mode, Enhanced Mode, SATA Only.
Default setting is Auto. Due to the Intel ICH5 Specification limited only provided two

controllers. When plug the Serial ATA hard drive in SATA1 or SATA2 only can support either
IDE1 or IDE2 can works in Windows 9X/ME/2000. But in the Windows XP the OS can
support 6 IDE devices both IDE1, IDE2 and SATA1/SATA2 can works.

3-7-3 Onboard Super IO Function

CMOS Setup Utility – Copyright(C) 1984-2003 Award Software

Onboard Super IO Function

Onboard FDD Controller Enabled
Onboard Serial Port 1 3F8/IRQ4
Onboard Serial Port 2 Disabled
UART Mode Select Normal
IR2 Duplex Mode Half
Onboard Parallel Port 378/IRQ7
Parallel Mode SPP
ECP Mode Use DMA 3

Item Help

Menu Level >>

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

Onboard FDD Controller

Select Enabled if your system has a floppy disk controller (FDD) installed on the system board
and you wish to use it. If you install add-on FDC or the system has no floppy drive, select
Disabled in this field. The settings are: Enabled and Disabled.

Onboard Serial Port 1/Port 2

Select an address and corresponding interrupt for the first and the second serial ports. The
settings are: 3F8/IRQ4, 2E8/IRQ3, 3E8/IRQ4, 2F8/IRQ3, Disabled, Auto.

UART Mode Select

This item allows you to determine which InfraRed(IR) function of the onboard I/O chip, this
functions uses.

Onboard Parallel Port

There is a built-in parallel port on the on-board Super I/O chipset that Provides Standard, ECP,
and EPP features. It has the following option:

Disabled
(3BCH/IRQ7)/
(278H/IRQ5)/
(378H/IRQ7)

Parallel Port Mode

Line Printer port 0

Line Printer port 2

Line Printer port 1

28

SPP : Standard Parallel Port
EPP : Enhanced Parallel Port
ECP : Extended Capability Port

SPP/EPP/ECP/ECP+EPP

To operate the onboard parallel port as Standard Parallel Port only, choose “SPP.” To operate the
onboard parallel port in the EPP modes simultaneously, choose “EPP.” By choosing “ECP”, the
onboard parallel port will operate in ECP mode only. Choosing “ECP+EPP” will allow the
onboard parallel port to support both the ECP and EPP modes simultaneously. The ECP mode
has to use the DMA channel, so choose the onboard parallel port with the ECP feature. After
selecting it, the following message will appear: “ECP Mode Use DMA” at this time, the user can
choose between DMA channels 3 to 1. The onboard parallel port is EPP Spec. compliant, so
after the user chooses the onboard parallel port with the EPP function, the following message will
be displayed on the screen: “EPP Mode Select.” At this time either EPP 1.7 spec. or EPP 1.9
spec. can be chosen.

3-8 Power Management Setup

The Power Management Setup allows you to configure your system to most effectively save
energy saving while operating in a manner consistent with your own style of computer use.

CMOS Setup Utility – Copyright(C) 1984-2003 Award Software

Power Management Setup

ACPI Function Enabled
Power Management User Define
Video off Method V/H SYNC+Blank
Video Off In Suspend Yes
Suspend Type Stop Grant
MODEM Use IRQ 3
Suspend Mode Disabled
HDD Power Down Disabled
Soft-off by PWR-BTTN Instant-off
Wake-Up by PCI card Disabled
Power On by Ring Disabled
Resume by Alarm Disabled
X Date (of Month) 0
X Time (hh:mm:ss) 0 : 0 :0
CPU Thermal Management Timer 32 Min

> PM Timer Reload Events Press Enter

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

Item Help

Menu Level >

ACPI Function

This item allows you to Enabled/Disabled the Advanced Configuration and Power Management
(ACPI). The settings are Enabled and Disabled.

Video Off in Suspend

This determines the manner in which the monitor is blanked. The choice are Yes → Video
will off , and No→ Video always On.

Video Off Method

29

This determines the manner in which the monitor is blanked.

DPMS
Blank Screen
V/H SYNC+Blank

Modem Use IRQ

This determines the IRQ in which the MODEM can use.
The settings are: 3, 4, 5, 7, 9, 10, 11, NA.

Power Button Function

Pressing the power button for more than 4 seconds forces the system to enter the Soft-Off state. The
settings are: Delay 4 Sec, Instant-Off.

Wake-Up by PCI card /Power On by Ring

During Disabled, the system will ignore any incoming call from the PCI card/modem. During Enabled,
the system will boot up if there’s an incoming call from the PCI card /modem.

Wake-Up on RTC Alarm

This function is for setting date and time for your computer to boot up. During Disabled, you cannot
use this function. During Enabled, choose the Date and Time Alarm:

Note: If you have change the setting, you must let the system boot up until it goes to the
operating system, before this function will work

PM Timer Reload Events

Please refer to section 3-8-1

(default) Initial display power management signaling.

This option only writes blanks to the video buffer.

This selection will cause the system to turn off the vertical and horizontal

synchronization ports and write blanks to the video buffer.

Date(of month) Alarm

You can choose which month the system will boot up. Set to 0, to boot every day.

Time(hh:mm:ss) Alarm

You can choose what hour, minute and second the system will boot up.

3-8-1 PM Timer Reload Events

CMOS Setup Utility – Copyright(C) 1984-2003 Award Software

PM Timer Reload Events

Primary IDE 0 Disabled

Primary IDE 1 Disabled
Secondary IDE 0 Disabled
Secondary IDE 1 Disabled
FDD, COM, LPT Port Disabled

PCI PIRQ [A-D] # Disabled

Item Help

Menu Level >>

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

3-9 PnP/PCI Configuration Setup

This section describes configuring the PCI bus system. PCI, or Personal Computer

30

Interconnect, is a system which allows I/O devices to operate at speeds nearing the speed the

CPU itself uses when communicating with its own special components. This section covers
some very technical items and it is strongly recommended that only experienced users should
make any changes to the default settings.

CMOS Setup Utility – Copyright(C) 1984-2003 Award Software

PnP/PCI Configurations

Reset Configuration Data Disabled

Resources Controlled By Manual
x IRQ Resources Press Enter

PCI/VGA Palette Snoop Disabled
Assign IRQ For VGA Enabled

Item Help

Menu Level >

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

Reset Configuration Data

Normally, you leave this field Disabled. Select Enabled to reset Extended System Configuration
Data (ESCD) when you exit Setup if you have installed a new add-on and the system
reconfiguration has caused such a serious conflict that the operating system can not boot. The
settings are: Enabled and Disabled.

Resource Controlled By

The Award Plug and Play BIOS has the capacity to automatically configure all of the boot and
Plug and Play compatible devices. However, this capability means absolutely nothing unless
you are using a Plug and Play operating system such as Windows95/98. If you set this field
to “manual” choose specific resources by going into each of the sub menu that follows this
field (a sub menu is preceded by a “>”).
The settings are: Auto(ESCD), Manual.

IRQ Resources

When resources are controlled manually, assign each system interrupt a type, depending on
the type of device using the interrupt.
Please refer to section 3-9-1

PCI/VGA Palette Snoop

Leave this field at Disabled. The settings are Enabled, Disabled.

3-9-1 IRQ Resources

31

CMOS Setup Utility – Copyright(C) 1984-2003 Award Software

IRQ Resources

IRQ-3 assigned to PCI Device
IRQ-4 assigned to PCI Device
IRQ-5 assigned to PCI Device
IRQ-7 assigned to PCI Device
IRQ-9 assigned to PCI Device
IRQ-10 assigned to PCI Device
IRQ-11 assigned to PCI Device
IRQ-12 assigned to PCI Device
IRQ-14 assigned to PCI Device
IRQ-15 assigned to PCI Device

Item Help

Menu Level >>

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

3-10 PC Health Status

This section shows the Status of you CPU, Fan, Warning for overall system status. This is only
available if there is Hardware Monitor onboard.

CMOS Setup Utility – Copyright(C) 1984-2003 Award Software

PC Health Status

Shutdown Temperature Disabled
CPU Warning Temperature Disabled
Show PC Health in Post Enabled
Current System Temperature 25°C
Current CPU Temperature 38°C
Current CPUFAN Speed 5000 rpm
Current SYSFAN Speed 5000 rpm
Current SYSFAN2 Speed 5000 rpm
Vcore 1.71V
Vcc1.5 1.51V
Vcc3.3 3.31V
+ 5V 4.98V
+12V 12.22V

-12V -12.36V

- 5V -4.99V
VBAT(V) 3.21V
5VSB(V)

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

5.02V

Item Help

Menu Level >

Show PC Health in Post

During Enabled, it displays information list below. The choice is either Enabled or Disabled.

Current CPU Temperature/Current System Temp/Current FAN1, FAN2 Speed/Vcore/Vdd/

3.3V/+5V/+12V/-12V/VBAT(V)/5VSB(V)

This will show the CPU/FAN/System voltage chart and FAN Speed.

Shutdown Temperature

This item can let users setting the Shutdown temperature, when CPU temperature over this setting the
system will auto shutdown to protect CPU.

3-11 Miscellaneous Control

32

This section is for setting CPU Frequency/Voltage Control.

CMOS Setup Utility – Copyright(C) 1984-2003 Award Software

Miscellaneous Control

CPU Clock Ratio 8 X
Auto Detect PCI Clk Enabled
Spread Spectrum Disabled
** Current Host Clock is 100/33MHz **
HOST/PCI Clock at Next Boot is 100/33MHz
** Current DRAM Clock is 133MHz **
DRAM Clock at Next Boot is DDR266
Flash Part Write Protect Enabled

Item Help

Menu Level >

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

Auto Detect PCI Clk

This item allows you to enable/disable auto detect PCI Clock.
The settings are: Enabled, Disabled.

Spread Spectrum

This item allows you to set the CPU Host/PCI clock and Spread Spectrum.
The settings are: Enabled, Disabled.

Host/PCI Clock at Next Boot

This item allows you to select CPU frequency step by step increasing.
The choice are: 400MHz CPU----100MHz~350MHz, 533MHz CPU---133MHz~350MHz
800MHz CPU---200MHz~350MHz

DRAM Clock at Next Boot is

This item allows you select the DRAM Clock for DDR266/DDR333/DDR400. The setting are:
DDR266 for P4/400MHz CPU, DDR266/DDR333 for P4/533MHz CPU, DDR266/DDR333
/DDR400 for P4/800MHz CPU

Flash Part Write Protect

This item allows you protect your BIOS chip from Virus destroy data. When Flash BIOS you
have Disabled this item.

3-12 Load Standard/Optimized Defaults

Load Standard Defaults

33

When you press <Enter> on this item, you get confirmation dialog box with a message similar
to:

Load Standard Defaults (Y/N)? N

Pressing <Y> loads the BIOS default values for the most stable, minimal-performance system
operations.

Load Optimized Defaults

When you press <Enter> on this item, you get a confirmation dialog box with a message
similar to:

Load Optimized Defaults (Y/N)? N

Pressing <Y> loads the default values that are factory settings for optimal performance system
operations.

3-13 Set Supervisor/User Password

You can set either supervisor or user password, or both of them. The differences are:

Supervisor password: Can enter and change the options of the setup menus.
User password: Can only enter but do not have the right to change the options of the

setup menus. When you select this function, the following message
will appear at the center of the screen to assist you in creating a
password.

ENTER PASSWORD:

Type the password, up to eight characters in length, and press <Enter>. The password typed
now will clear any previously entered password from CMOS memory. You will be asked to
confirm the password. Type the password again and press <Enter>. You may also press
<Esc> to abort the selection and not enter a password.

To disable a password, just press <Enter> when you are prompted to enter the password. A
message will confirm that the password will be disabled. Once the password is disabled, the
system will boot and you can enter Setup freely.

PASSWORD DISABLED.

When a password has been enabled, you will be prompted to enter it every time you try to
enter Setup. This prevents an unauthorized person from changing any part of your system
configuration.

Additionally, when a password is enabled, you can also require the BIOS to request a
password every time your system is rebooted. This would prevent unauthorized use of your
computer.

You determine when the password is required within the BIOS Features Setup Menu and its
Security option. If the Security option is set to “System”, the password will be required both
at boot and at entry to Setup. If set to “Setup”, prompting only occurs when trying to enter
Setup.

Chapter 4

DRIVER & FREE PROGRAM INSTALLATION

34

Check your package and there is A MAGIC INSTALL CD included. This CD consists of all
DRIVERS you need and some free application programs and utility programs. In addition, this
CD also include an auto detect software which can tell you which hardware is installed, and
which DRIVERS needed so that your system can function properly. We call this auto detect
software MAGIC INSTALL.

MAGIC INSTALL Supports WINDOWS 98SE/ME/NT4.0/2000/XP

Insert CD into your CD-ROM drive and the MAGIC INSTALL Menu should appear as below.
If the menu does not appear, double-click MY COMPUTER / double-click CD-ROM drive or
click START / click RUN / type X:\SETUP.EXE (assuming X is your CD-ROM drive).

From MAGIC INSTALL MENU you may make 10 selections:

INF install Intel 865 chipset system driver

1.

2. VGA install Intel 865G VGA driver (Only for 865GDA/865GDAP)

3. SOUND install ALC AC97’ Codec Audio driver

4.

LAN install VIA LAN Controller driver (for 865GDAP/865PEDAP)

5. USB2.0 install USB 2.0 driver

6. PC-CILLIN install PC-CILLIN2002 anti-virus program

7. PC-HEALTH install ITE Smart GUARDIAN driver

8. MBIOS&DX8 install BIOS Live Update Utility and Microsoft DirectX 8.1 driver

9. BROWSE CD to browse the contents of the CD

10. EXIT to exit from MAGIC INSTALL menu

4-1 INF install Intel 865 chipset system driver

After you have completed the installation of your operation system (WINDOWS 98SE). You will find
an UNKNOWN DEVICE in the device manager (START/SETTING/CONTROL PANEL/
SYSTEM/DEVICE MANAGER). You have to install INF driver as shown below:

35

1. Click INF in the MAGIC INSTALL MENU 2. Click NEXT when Chipset Software Install

Utility appears

3. This license agreement appear , click Yes ,

the readme information appear , click Next

NOTE: MAGIC INSTALL will auto detect file path X:\INTEL845\INF\SETUP.EXE
This driver supports WINDOWS 98SE/ME/2000/XP
(NT4.0 do not require)

4. Select if you want computer re-started click

Finish

4-2 VGA install Intel 865G VGA Driver

1. Click VGA when MAGIC INSTALL

MENU appears

2. Click NEXT When Intel (R) Extreme

Graphics Driver Software Setup appear

36

3. Click YES, This is Announce CopyRight 4. If You Want Re-start Computer , Click

FINISH

4-3 SOUND install ALC AC97’ Codec Audio Driver

1. Click SOUND when MAGIC INSTALL

MENU appears

3. Click Finish and Restart Windows

2. Then auto detect operation system language

edition, click OK, start to install DRIVER

4. Click Start→Program→Avance Sound
Manager→AvRack. Then AVRACK Windows
appears

37

5. Sound Effect select and KaraOK Mode

Function

6. Manual Sound Effect Setting

Note: The path of the file

For WIN98/NT4.0/WIN2K/XP is X:\CODEC\ALC\SETUP.EXE

Note: In Win2K/WinME users have to click Control Panel\System\Device Manager\

DVD\CD-ROM drives to Enabled digital CD Audio for the CD-ROM Device when
use the SPDIF-Out digital signal.

4-4 LAN install VIA 6105 LAN Controller Driver

WINDOWS 98SE/98ME/2000/XP Setup

1. Click LAN when Magic Install Menu appear 2. Install VIA VT6105 PCI 10/100M Fast
Ethernet Driver

3. Select YES and Restart your computer

X:\RTLLAN\WIN98 (If OS is win9X)

38

4-5 USB2.0 install Intel USB2.0 Driver

Windows 98SE/ME USB 2.0 Driver installation

1. Click USB2.0 when Magic Install Menu

appear

2. This license agreement appear, click Yes, then

finish install driver , click Close and restart
your computer

Windows 2000/XP USB 2.0 Driver installation

Windows 2000

Mothed1 Start Windows 2000 OS and Internet Connect, Select "Windows Update",
Select Driver Update, Install Windows2000 USB2.0 Driver
Mothed2 Install Windows 2000 Service Pack 4 or later

Windows XP

Install Windows XP Service Pack 1 or later

4-6 PC-HEALTH install SMART GUARDIAN Software for

Hardware Monitoring Device

1. Click PC-HEALTH when MAGIC INSTALL

MENU appears

2. Click OK when SMART GUARDIAN

INSTALL appears

39

3. This to assign the path of the file, click NEXT 4. Click FINISH after the software is installed

NOTE: MAGIC INSTALL will auto detect file path X:\INTEL865\HEALTH\SETUP.EXE

This driver supports WINDOWS 95/98/98SE/NT4.0/2000

4-6-1 HOW TO UTILIZE PC-HEALTH

1. Click START/PROGRAMS/ITE SMART

ACCESSORIES / ITE SMART GUARDIAN

2. You will see a real time report about FAN

SPEED, VOLTAGE and TEMPERATURE
System will make a warning if any value is
beyond Initial setting value

3. You may re-set temperature and voltage by

click OPTION

4-7 MBIOS&DX8 Install BIOS Live Update Utility and

40

DIRECTX8.1

1. Click Magic BIOS when Magic Install

MENU appears

2. Click Next to install the Magic BIOS in

Destination Folder

3. After finish Setup you will have a Magic

BIOS icon in your screen

5. When On-line update BIOS the program will

auto-check your BIOS version

4. Double click the Magic BIOS icon you will

have this picture, choose from internet you can
upgrade BIOS On-line

6. Click Next if you need update BIOS, after

upgrade BIOS, the system will clear CMOS
and automatically restart

41

7. Click Yes if you want to update the BIOS

otherwise choose No to exit

8. When System programming BIOS don’t turn

off power, after finish update BIOS, the
system will clear CMOS and automatically
Restart

9. When choose From Local Driver to update

BIOS, you must have the correct BIOS file
in your Local Driver

10. Choose the correct BIOS file to update BIOS

4-8 PC-CILLIN Install PC-CILLIN 2002 Anti-virus program

1. Click PC-CILLIN when MAGIC INSTALL

MENU appear

2. (1) Click "Install PC-CILLIN" when PC-

CILLIN 2002 main menu appears, and Click
NEXT when "Install Shield Wizard For PC­CILLIN 2002"

(2) Click Open Manual. you can learn PC­CILLIN 2002 how to use

42

3. This is license agreement, select "I Accept

the terms" and Click NEXT

4. Click NEXT and Enter your Customer

Information, Click NEXT or choose Change
to change the path for the file to be stored

5. Click INSTALL, Start to install the software

6. Setup Complete and click FINISH

7. After PC-CILLIN 2002 complete, Please

register your information and get LICENSE
KEY from TREND MICRO web site, enter
your license key and click FINISH

8. finish register process, we recommend select

update item to download newest engine code
and virus code

Note : Please install ACROBAT READER, Before you read PC-CILLIN 2002 User

Manual, the path at X:\acrobat\ar500eng.exe

43

4-9 HOW TO UPDATE BIOS

Before update BIOS users have to “Disable”, “Flash Part Write Protect” item which in
“Miscellaneous Control” of BIOS SETUP. Otherwise the system the will not allow you to
upgrade BIOS by Award Flash Utility.

Method 1. Use “Magic BIOS” update BIOS in Windows 98 (refer page 41)
Method 2. In DOS Mode

STEP 1. Prepare a boot disc. (you may make one by click START click RUN type SYS A:

click OK)

STEP 2. Copy utility program to your boot disc. You may copy from DRIVER CD

X:\FLASH\AWDFLASH.EXE or download from our web site.

STEP 3. Copy latest BIOS for 865GDA/865PEDA from our web site to your boot disc.

STEP 4. Insert your boot disc into A:,

start the computer, type “Awdflash A:\865GDAAxxx.BIN /SN/PY/CC/R”
865GDAAxxx.BIN is the file name of latest BIOS it can be 865GDAA03.BIN or

865GDAB02.BIN
SN means don’t save existing BIOS data
PY means renew existing BIOS data
CC means clear existing CMOS data
R means restart computer

STEP 5. Push ENTER and the BIOS will be updated, computer will be restarted automatically.

44