Jetway 865GVBMS User Manual

865GVBMS/865GVBM

USER'S MANUAL

M/B For LGA 775 Pentium 4 Processor

NO. G03865GVBMR207

Rev:2.0

Release date: August 2005

Trademark:

*

Specifications and Information contained in this documentation are furnished for information use only, and are

subject to change at any time without notice, and should not be construed as a commitment by manufacturer.

USER’S NOTICE .................................................................................................................................. ii

MANUAL REVISION INFORMATION............................................................................................ ii

COOLING SOLUTIONS...................................................................................................................... ii

CHAPTER 1 INTRODUCTION OF 865GVBMS/865GVBM MOTHERBOARD

1-1 FEATURE OF MOTHERBOARD ...................................................................................... 1

1-2 SPECIFICATION.................................................................................................................. 2

1-3 PERFORMANCE LIST........................................................................................................ 3

1-4 LAYOUT DIAGRAM & JUMPER SETTING................................................................... 4

CHAPTER 2 HARDWARE INSTALLATION

2-1 HARDWARE INSTALLATION STEPS ............................................................................ 6

2-2 CHECKING MOTHERBOARD'S JUMPER SETTING .................................................. 6

2-3 INSTALL CPU....................................................................................................................... 7

2-3-1 GLOSSARY................................................................................................................ 7

2-3-2 ABOUT INTEL PENTIUM 4 LGA 775 CPU ......................................................... 8

2-3-3 LGA 775 CPU INSTALLATION GUIDE ............................................................... 9

2-4 INSTALL MEMORY............................................................................................................ 18

2-5 EXPANSION CARD ............................................................................................................. 19

2-5-1 PROCEDURE FOR EXPANSION CARD INSTALLATION .............................. 19

2-5-2 ASSIGNING IRQ FOR EXPANSION CARD ........................................................ 19

2-5-3 INTERRUPT REQUEST TABLE FOR THIS MOTHERBOARD ...................... 20

2-6 CONNECTORS, HEADERS................................................................................................ 20

2-6-1 CONNECTORS ......................................................................................................... 20

2-6-2 HEADERS .................................................................................................................. 23

2-7 STARTING UP YOUR COMPUTER ................................................................................. 26

CHAPTER 3 INTRODUCING BIOS

3-1 ENTERING SETUP .............................................................................................................. 27

3-2 GETTING HELP................................................................................................................... 27

3-3 THE MAIN MENU................................................................................................................ 28

3-4 STANDARD CMOS FEATURES........................................................................................ 29

3-5 ADVANCED BIOS FEATURES.......................................................................................... 30

3-6 ADVANCED CHIPSET FEATURES.................................................................................. 32

3-6-1 DRAM TIMING SETTINGS.................................................................................... 33

3-7 INTEGRATED PERIPHERALS ......................................................................................... 34

3-7-1 ONBOARD IDE FUNCTION................................................................................... 34

3-7-2 ONBOARD DEVICE FUNCTION .......................................................................... 35

3-7-3 ONBOARD SUPER IO FUNCTION ....................................................................... 36

3-8 POWER MANAGEMENT SETUP ..................................................................................... 37

3-8-1 PM TIMER RELOAD EVENTS ............................................................................. 38

3-9 PNP/PCI CONFIGURATION SETUP ................................................................................ 38

3-9-1 IRQ RESOURCES.................................................................................................... 39

3-10 PC HEALTH STATUS ........................................................................................................ 40

3-11 MISCELLANEOUS CONTROL........................................................................................ 41

3-12 LOAD STANDARD/OPTIMIZED DEFAULTS............................................................... 42

3-13 SET SUPERVISOR/USER PASSWORD .......................................................................... 42

CHAPTER 4 DRIVER & FREE PROGRAM INSTALLATION

MAGIC INSTALL SUPPORTS WINDOWS 98SE/ME/NT4.0/2000/XP ................................... 43

4-1 INF INSTALL INTEL 865GV CHIPSET SYSTEM DRIVER ....................... 44

4-2 VGA INSTALL 865GV VGA DRIVER .............................................................. 44

4-3 SOUND INSTALL ALC AC97’ CODEC AUDIO DRIVER .................................. 45

4-3 LAN INSTALL VIA 6105/6106S LAN CONTROLLER DRIVER .................. 46

4-5 USB2.0 INSTALL INTEL USB2.0 DRIVER .......................................................... 47

4-6 PC-HEALTH PC-HEALTH INSTALL INTEL HARDWARE DOCTOR UTILITY.. 47

4-7 MBIOS&DX9 INSTALL BIOS LIVE UPDATE UTILITY AND DIRECTX9............... 48

4-8 PC-CILLIN INSTALL PC-CILLIN2004 ANTI-VIRUS PROGRAM .................. 50

4-9 HOW TO UPDATE BIOS .................................................................................................... 51

TABLE OF CONTENT

i

USER’S NOTICE

COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL,
INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED,
TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS WITHOUT
WRITTEN PERMISSION OF THE MANUFACTURER.

THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE 865GVBMS/865GVBM MOTHER­BOARD AND WE DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT WILL CHANGE,
CORRECT ANY TIME WITHOUT NOTICE. MANUFACTURER PROVIDES THIS MANUAL “AS IS”
WITHOUT WARRANTY OF ANY KIND, AND WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTIAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMANGES FOR LOSS OF PROFIT, LOSS
OF BUSINESS, LOSS OF USE OF DATA, INTERRUPTION OF BUSINESS AND THE LIKE).

PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE
REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES, AND THEY ARE
USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER’S BENEFIT, WITHOUT
INTENT TO INFRINGE.

Manual Revision Information

Reversion Revision History Date

2.0 Second Edition August 2005

Item Checklist

5

865GVBMS/865GVBM Motherboard

5

Cable for IDE/Floppy

5

CD for motherboard utilities

5

Cable for Serial ATA IDE Port

5

865GVBMS/865GVBM User’s Manual

Intel Pentium 4 Processor Family

Cooling Solutions

As processor technology pushes to faster speeds and higher performance, thermal management
becomes increasingly crucial when building computer systems. Maintaining the proper thermal
environment is key to reliable, long-term system operation. The overall goal in providing the proper
thermal environment is keeping the processor below its specified maximum case temperature.
Heatsinks induce improved processor heat dissipation through increased surface area and concentrated
airflow from attached fans. In addition, interface materials allow effective transfers of heat from the
processor to the heatsink. For optimum heat transfer, Intel recommends the use of thermal grease and
mounting clips to attach the heatsink to the processor.

When selecting a thermal solution for your system, please refer to the website below for collection of
heatsinks evaluated and recommended by Intel for use with Intel processors. Note, those heatsinks are
recommended for maintaining the specified Maximum T case requirement. In addition, this collection
is not intended to be a comprehensive listing of all heatsinks that support Intel processors.

For vendor list of heatsink and fan, please visit :
http://developer.intel.com/design/Pentium4/components/index

ii

Chapter 1

Introduction of 865GVBMS/865GVBM Motherboard

1-1 Feature of motherboard

The 865GVBMS/865GVBM motherboard is design for use Intel Pentium 4 Processor in
LGA775 (Land Grid Array) Socket Prescott Processor with the Intel 865GV Chipset delivers a
high performance and professional desktop platform solution. Which utilize the design and
the memory size expandable to 2.0GB.

These motherboards use the newest Intel 865GV Chipset Supports 800/533MHz System Bus
in data transfer rate, these motherboards provided 200/166/133MHz SDRAM clock frequency
support DDR400/DDR333/DDR266 SDRAM. These motherboards also provided Dual
Channel function to increase memory performance. The motherboard embedded ICH5
chipset offers two parallel ULTRA ATA 100 interface and two serial ATA interface to
provide speedier HDD throughout that boosts overall system performance.

The 865GVBMS motherboard including Fast Ethernet PCI controller chip support 10Mb/s,
100Mb/s Base transfer rate.

These motherboards also has an integrated 6-channel AC97’ CODEC chip on board support
6-channel 3D surround positioning Audio which is fully compatible with Sound Blaster Pro
that gives you the best sound quality and compatibility.

With USB control as well as capability of expanding to eight USB2.0 function ports, these
motherboards meet future USB demand also these motherboards have built-in hardware
monitor function. This will monitor and protect your computer. These motherboards special
design in hardware to protect BIOS from virus crash BIOS data.

These motherboards provide special function in BIOS Setup to setting CPU Host clock step
by step increasing let users to approach over clocking.

These motherboards provided high performance & meet future specification demand. It is
really wise choice for your computer.

1

1-2 Specification

Spec Description

Design

Chipset

CPU Socket

(LGA 775 Socket)

Memory Socket

Expansion Slot

Integrate VGA

Integrate IDE

Integrate Serial ATA

LAN On Board
(for 865GVBMS)

Audio

BIOS

Multi I/O

∗ Micro ATX form factor 4 layers PCB size: 24.5x21.0cm
∗ Intel 865GV Controller Hub (MCH) Chipset
∗ Intel 82801EB I/O Controller Hub (ICH5) Chipset
∗ Support Intel Pentium 4 775-Land LGA Package utilizes Flip-

Chip Land Grid Array (FCLGA4) package processor

∗ Support CPU Frequency 533MHz/800MHz
∗ Support 2.8G~3.6G LGA 775 Pentium 4 processor
∗ Reserves support for future Intel Pentium 4 processors
∗ 184-pin DDR SDRAM module socket x2
∗ Support Dual channel DDR266/DDR333/DDR400 DDR

SDRAM

∗ Expandable to 2.0GB
∗ 32-bit PCI slot x 3

∗ Integrated High Performance & High Quality 3D Accelerator
∗ Support Ultra-AGPII with 2GB/s bandwidth

∗ Built-in programmable 24-bit true-color RAMDAC up to

333MHz pixel clock

∗ Two IDE controllers support PCI Bus Mastering, ATA

PIO/DMA and the ULTRA DMA 33/66/100 functions that
deliver the data transfer rate up to 100 MB/s

∗ Two Serial ATA Host controllers, that deliver the data transfer

rate up to 150 MB/s

∗ VIA VT6106S PCI LAN controller chip
∗ Supports 10/100 Mb/sec data transfer rate
∗ Realtek ALC 6-channel AC97’ Codec integrated
∗ Support 6-channel 3D surround & Positioning Audio
∗ Audio driver and utility included
∗ Award 4Mb Flash ROM
∗ PS/2 keyboard and PS/2 mouse connectors
∗ Floppy disk drive connector x1
∗ Parallel port x1, Serial port x1
∗ USB 2.0 connector x4, headers x4 (connecting cable option)
∗ Audio connector Line-in, Line-out, & MIC

2

1-3 Performance List

The following performance data list is the testing result of some popular benchmark testing
programs. These data are just referred by users, and there is no responsibility for different
testing data values gotten by users (the different Hardware & Software configuration will
result in different benchmark testing results.)

Performance Test Report

CPU:
DRAM:

KINGSTON D328DW 512M DDR400 X 2 PCS Total 1Gbyte Memory

On board VGA:
Hard Disk Driver:
BIOS:

Win XP Professional (Service Pack 1)

OS:

Award Optimal default

Intel Pentium 4 3GHZ (800MHz FSB) Hyper-Threading Support

(1024X768X32BIT Color)

IBM IC35L040AVVN07-0 (ATA-100 7200RPM)

3D Mark 2001SE 2929
3D Mark 2003 92
3D Winbench 2000 (32/32BIT) 83.1
PC Mark2002
CPU/Memory/HDD 7380 / 7632 / 877
Content Creation Winstone 2002 46.4
Content Creation Winstone 2003 50.1
Business Winstone 2002 33.1
Winbench 99 V1.2:
Business Disk Winmark99 9180
Hi-end Disk Winmark99 32900
Business Graphic Winmark 277
Hi-end Graphic Winmark 898
SYS Mark 2001/2002 : SISMark 2001/2002 Rating ( Internet Content
Creation / Office Productivity )
SISMark 2001 271 (317 / 231)
SISMark 2002 in Windows XP 316 (436 / 229)
SISOFT Sandra 2003 :
Dhrystone ALU MIPS 9183
Whetstone FPU iSSE2 MFLOPS 2601 / 5416
RAM Int Buffered iSSE2 MB/S 4266
RAM Float Buffered iSSE2 MB/S 4263
Integer SSE2 IT/S 11749
Floating-Point SSE2 IT/S 21590
Quake3 DEMO1 FPS 134.5

DEMO2 FPS 135.9
Return to Castle Wolfenstein FPS 88.9
WCPUID System / CPU Clock 199.71 / 2995.70

3

1-4 Layout Diagram & Jumper Setting

PRINT

(for 865GVBMS)

LAN

MIC

PS/2 Mouse

PS/2 Keyboard

PS2 KB/Mouse Port

PC99 Back Panel

ATX 12V Power Connector

KB/USB Power ON Jumper

USB Port (USB1)

(JP2)

USB Port/LAN Connector

ATX Power Connector

Audio Connector (CN1)

SYSFAN1

USB Port

VIA VT6106S LAN Controller

6-CH AC’97 Audio Codec

(USB3, USB2)

PCI Slot

CD Audio

Front Panel Audio

IR Connector

SYSFAN2

COM1 VGA USB1 USB

LINE-IN

LINE-OUT

CPU Socket

FINTEK F71872F I/O Chip

CPU FAN

DDR DIMMx2

Floppy Connector

Intel 865GV Chip

ATA 100 IDE Connector

USB Power ON Jumper
(JP3)

Intel 82801EB Chip
Clear CMOS
Serial-ATA Connector

(SATA1, 2)

Front Panel Connector

Power LED/
Speak Connector

4MBit FWH BIOS

(JP4)

4

Jumpers

Jumper Name Description Page

JP4 CMOS RAM Clear 3-pin Block P.6
JP2 Keyboard/USB Power On Enable/Disabled 3-pin Block P.7
JP3 USB Power On Enable/Disabled 3-pin Block P.7

Connectors

Connector Name Description Page

ATXPWR24 ATX Power Connector 24-pin Block P.20
ATX12V ATX 12V Power Connector 4-pin Block P.21
USB1, UL_B USB Port Connector 4-pin Connector P.21

LAN
(for 865GVBMS)

KB
(PS2 KB/MOUSE)
PARALLEL Parallel Port Connector 25-pin Female P.21
CN1 Audio Line In/Out MIC Connector 3 phone jack Connector P.21
COM1 Serial Port COM1 Connector 9-pin Connector P.21
VGA VGA Display Connector 15-pin Female Connector P.21
FDD Floppy Driver Connector 34-pin Block P.22
IDE1/IDE2 Primary/Secondary 40-pin Block P.22
SATA1, SATA2 Serial-ATA Port Connector 7-pin Block P.23

LAN Connectors RJ-45 Connector P.21

PS/2 Mouse & PS/2 Keyboard

6-pin Female P.21

Connector

Headers

Header Name Description Page

AUDIO Line-Out, MIC Headers 9-pin Block P.23
USB2, USB3 USB Port Headers 9-pin Block P.23
SPEAK Speaker connector 4-pin Block P.24
JW_FP
(Power LED/Reset/
IDE LED/ Power Button)

Front Panel Header
(including Power LED/ IDE activity LED/
Reset switch / Power On Button lead)

9-pin Block P.24

CPUFAN FAN Headers 4-pin Block P.24
SYSFAN1, SYSFAN2 FAN Headers 3-pin Block P.24
IR IR infrared module Headers 5-pin Block P.25
CDIN CD Audio-In Headers 4-pin Block P.25

Expansion Sockets

Socket/Slot Name Description Page

LGA 775 Socket CPU Socket LGA 775 CPU Socket
DIMM1, DIMM2 DDR Module Socket 184-pin DDR SDRAM Module

Expansion Socket

PCI1 ∼ PCI3

PCI Slot 32-bit PCI Local Bus Expansion slots P.19

P.8
P.18

5

Chapter 2

Hardware installation

2-1 Hardware installation Steps

Before using your computer, you had better complete the following steps:

1. Check motherboard jumper setting

2. Install CPU and Fan

3. Install System Memory (DIMM)

4. Install Expansion cards

5. Connect IDE and Floppy cables, Front Panel /Back Panel cable

6. Connect ATX Power cable

7. Power-On and Load Standard Default

8. Reboot

9. Install Operating System

10. Install Driver and Utility

2-2 Checking Motherboard’s Jumper Setting

(1) CMOS RAM Clear (3-pin) : JP4

A battery must be used to retain the motherboard configuration in CMOS RAM short 1-2
pins of JP4 to store the CMOS data.

To clear the CMOS, follow the procedure below:

1. Turn off the system and unplug the AC power

2. Remove ATX power cable from ATX power connector

3. Locate JP4 and short pins 2-3 for a few seconds

4. Return JP4 to its normal setting by shorting pins 1-2

5. Connect ATX power cable back to ATX power connector

Note: When should clear CMOS

1. Troubleshooting

2. Forget password

3. After over clocking system boot fail

1 3

JP4

1 3

JP4

1-2 closed Normal (Default)

CMOS RAM Clear Setting

2-3 closed Clear CMOS

6

(2) Keyboard/USB Power On function Enabled/Disabled: JP2, JP3

When setting Enabled you can using keyboard by key in password/USB device to power
on system.

JP2

JP3

1 3

1 3

JP3

1

3

JP2 1-2 closed Keyboard/USB Power On Disabled (Default)

JP2 2-3 closed Keyboard/USB Power On Enabled

JP3 1-2 closed USB Power On Disabled (Default)

1

JP3 2-3 closed USB Power On Enabled

3

JP2

2-3 Install CPU

2-3-1 Glossary

Chipset (or core logic) - two or more integrated circuits which control the interfaces between
the system processor, RAM, I/O devises, and adapter cards.
Processor slot/socket - the slot or socket used to mount the system processor on the
motherboard.

Slot (AGP, PCI, ISA, RAM) - the slots used to mount adapter cards and system RAM.
AGP - Accelerated Graphics Port - a high speed interface for video cards; runs at 1X

(66MHz), 2X (133MHz), 4X (266MHz),
PCI - Peripheral Component Interconnect - a high speed interface for video cards, sound
cards, network interface cards, and modems; runs at 33MHz.
ISA - Industry Standard Architecture - a relatively low speed interface primarily used for
sound cards and modems; runs at approx. 8MHz.

Serial Port - a low speed interface typically used for mouse and external modems.
Parallel Port - a low speed interface typically used for printers.
PS/2 - a low speed interface used for mouse and keyboards.
USB - Universal Serial Bus - a medium speed interface typically used for mouse, keyboards,

scanners, and some digital cameras.
Sound (interface) - the interface between the sound card or integrated sound connectors and
speakers, MIC, game controllers, and MIDI sound devices.

LAN (interface) - Local Area Network - the interface to your local area network.
BIOS (Basic Input/Output System) - the program logic used to boot up a computer and

establish the relationship between the various components.
Driver - software, which defines the characteristics of a device for use by another device or
other software.
Processor - the "central processing unit" (CPU); the principal integrated circuit used for
doing the "computing" in "personal computer"

Front Side Bus Frequency -

the working frequency of the motherboard, which is generated

by the clock generator for CPU, DRAM and PCI BUS.

CPU L2 Cache -

the flash memory inside the CPU, normally Athlon CPU has 256K or above,

while Duron will have 64K.

or 8X (533MHz).

7

2-3-2 About Intel Pentium 4 LGA775 CPU

This motherboard provides a 775-pin surface mount, LGA775 Land Grid Array socket,
referred to as the LGA775 socket supports Intel Pentium 4 processor in the 775 Pin package
utilizes Flip-Chip Land Grid Array (FC-LGA4) package technology.

The CPU that comes with the motherboard should have a cooling FAN attached to prevent
overheating. If this is not the case, then purchase a correct cooling FAN before you turn on
your system.

WARNING!

Be sure that there is sufficient air circulation across the processor’s
heatsink and CPU cooling FAN is working correctly, otherwise it may
cause the processor and motherboard overheat and damage, you may install
an auxiliary cooling FAN, if necessary.

To install a CPU, first turn off your system and remove its cover. Locate the LGA775 socket
and open it by first pulling the level sideways away from the socket then upward to a 90­degree angle. Insert the CPU with the correct orientation as shown below. The notched
corner should point toward the end of the level. Because the CPU has a corner pin for two

of

the four corners, the CPU will only fit in the orientation as shown.

LGA775

Colden Arrow

When you put the CPU into the LGA775 socket. No force require to insert of the CPU, then
press the level to Locate position slightly without any extra force.

CPU LGA775 Socket

8

2-3-3 LGA 775 CPU Installation Guide

Socket Preparation

1. Opening the socket:

Note: Apply pressure to the corner with right hand thumb while opening/closing the load lever,

otherwise lever can bounce back like a “mouse trap” and WILL cause bent contacts (when

loaded)

Socket Load
Plate Open

1. Disengage Load Lever by depressing down and

out on the hook to clear retention tab

2. Rotate Load Lever to fully open position at

approximately 135degrees

3. Rotate Load Plate to fully open position at

approximately 100degrees

Socket Load
Lever Open

2. Remove PnP Cap (Pick & Place Cap)

i. With left hand index finger and thumb to support the load plate edge, engage PnP cap with right

hand thumb and peel the cap from LGA775 Socket while pressing on center of PnP cap to assist in

removal.

ii. Set PnP cap aside. Always put PnP cap back on if the processor is removed from the socket.

iii. Visually inspect PnP cap for damage. If damage observed, replace the PnP cap.

Note: After PnP cap removal, make sure

socket load plate and contacts are free of

foreign material; Refer to Overview Module for

FM cleaning.

Note: Optionally, remove PnP cap after CPU insertion.

This will compromise the ability to visually

inspect socket.

9

3. Visually inspect for bent contacts (Recommend at least 1stpass visual inspection)

NOTE: Refer to the Handling and Inspection Module for 1stand 2ndpass inspection details.

NOTE: Glove images are for illustrative purposes only. Please consult local safety guidelines for

specific requirements

NOTE: Recommend not to hold the load plate as a lever, instead hold at tab with left hand, removing

the PnP cap with right hand

775-land LGA Package Insertion

Press to remove

Pin 1 Indicator

Alignment Key

1. Lift processor package from shipping media by

grasping the substrate edges ONLY.

Note: Orient processor package such that the Pin 1

triangle mark is on bottom left and both key
notches are on left side

2. Land Side Cover Handling: Remove land side cover

with the opposite hand by depressing larger
retention tab and peeling the cover away

3. Set and reserve the land side cover aside.

Note: Always keep the land side cover on the

processor when not in the socket.

4. Visually inspect the package gold pads: Scan the

processor package gold pad array for presence of
foreign material. Refer to Overview Module for FM
cleaning recommendations

5. Orient the package with IHS up. Locate Pin 1 and

the two orientation key notches

6. Carefully place the package into the socket body

using a purely vertical motion

CAUTION: Using Vacuum Pen for installation is not recommended

7. Verify that package is within the socket body and

properly mated to the orient keys

8. Close the socket by

i. Rotating the Load Plate onto the package HIS

ii. While pressing down lightly on Load Plate, engage

the Load Lever.

iii. Securing Load Lever with Load Plate tab under

retention tab of Load Lever

10

775-Land Package Removal

1. Open the Load Plate/Lever with both hands:

With left hand index finger and thumb to support

the load plate edge, engage PnP cap with right hand
thumb and peel the cap from LGA775 Socket while
pressing on center of PnP cap to assist in removal.

2. Pick up 775-land LGA package:

By Vacuum Pen: Place a minimum 9-mm cup at

approximately the center of IHS.
Recommend not to place Vacuum Pen on IHS edge.
Risk of dropping and causing bent contact.
Recommend not to use Vacuum Pen for inserting
CPU By Hand: Index finger to hold load plate hinge

side and thumb to hold load lever side

Chamfer on Land Side
Cover (align this with
pin 1 mark on 775-land
LGA package)

Large Retention Tabs
(pointing towards user)

onto

Hold at corners

3. Lift the package straight up and away.

4. Assemble processors land side cover immediately

to prevent contamination.

i. While holding the processor by the 3 corners, the

other hand lift land side cover from work surface
by grasping at the large retention tabs. Ensure
retention tabs and package are pointing each
other.

ii. Orientate so that land side cover chamfer is

matching with package Pin 1 location.

iii. Hook the first large retention tab on the package

substrate. Then press the opposite tab onto the
substrate.

iv. Place processor with land side cover installed

proper shipping media or other ESD approved
work surface

11

5. Visually inspect socket contact array

1. First Pass Inspection

i. Scan socket contact array at varying angles noting the presence of any foreign material

ii. If foreign material can’t be blown off by compressed air, or mechanical damage (Mode1 or 4)

observed, reject the motherboard for further evaluation or socket replacement.

2. Second Pass Inspection

i. Repeat 2 more times to sight down the rows and columns from each of the 4 sides of the socket to

ensure all contacts within the array are inspected

ii. Inspect for Mode2, Mode3, and Mode5 failures

Note: Refer to the Test Module for detail visual inspections

6. Assemble LGA775 socket PnP cap

i. Secure/Hook the back side of PnP cap.

ii. Snap down the front side to fully secure

7. Close the Socket

Intel Reference Thermal Solution Assembly

NOTE: Depending on the configuration, Thermal Solution Integration procedure could perform with

M/B alone or with M/B in the Chassis.

Fan cabled on side
closest to MB header

0.150-inch backside
clearance for fastener
installation

1. Place motherboard on support structure providing

minimum 0.150-inch backside clearance

2. Apply 300 mg of Thermal Interface Material (Shin-

Fastener slots
pointing straight out

Etsu G751) onto center of IHS

12

NOTE: Thermal Solutions that come with IntelR boxed

Apply Thermal
Interface Material

processor use pre-applied thermal interface material
and not grease.

3. Remove Heat Sink (HS) from packaging media

4. Place HS onto the LGA775 Socket

• Ensure fan cables are oriented on side closest to

fan header

• Align Fasteners with MB through-holes

5. Inspection

• Ensure cables are not trapped or interfere

fastener operation

• Ensure fastener slots are pointing straight out

from heatsink

Fastener Cap not
resting against spring

Press Down
(4 Places)

Fastener flush
against MB

Both fastener
halves are flush
against spring

Fastener flush
against spring

6. Actuate fasteners

• While holding HS to prevent tilting, press down on

fastener caps with thumb to install and lock

Repeat with remaining fasteners

7. Inspection

• Verify the fasteners are properly seated

• Ensure both fastener cap and base are flush with

spring and motherboard

8. Connect fan header with Board header

9. Secure excess cable with tie-wrap to ensure

cable does not interfere with fan operation or
contact other components.

13

Intel Reference Thermal Solution Disassembly

1. Rotate fastener cap. turn to un-lock

2. Pull up fastener cap to un-seat 12

1. Disconnect fan cable from motherboard header

2. Turn fastener caps (4) counter-clock wise

90degrees to the un-locked position

• A flat-bladed screwdriver may be used if required

3. Pull up on fastener caps to unseat

4. Manually remove HS with gentle twist motion.

5. To re-assemble the HS, reset the fastener caps to

their original position with the slot perpendicular
to the HS. Then, follow the assembly instructions.

Note: Thermal grease should be reapplied

TIM and Grease Removal from CPU

1 2

3

4

14

6

IPA

5

Dry

1. Remove the heatsink from the socket

2. Gently push loose thermal interface material (TIM) to center of processor (pictures 2 and 3)

3. Remove pieces with dry cloth (picture 4)

4. Wipe with dry, lint-free cloth to remove most of the material (picture 5)

5. Wet another lint-free cloth with isopropyl alcohol (IPA) and wipe to clean remaining material

(picture 6)

6. Be careful to remove material from gaps between processor and load plate

7. For thermal grease removal use Step 4-6

TIM and Grease Removal from Heat-sink

Note: Remove and replace the TIM from the heatsink if you are re-using the heatsink on a new

processor

1. Use dry, lint-free cloth and wipe package to remove most of the material

2. Wet another lint-free cloth with isopropyl alcohol (IPA) and wipe heatsink to clean remaining

material

Removal TIM from heatsink

1

Dry

15

Dry

1

2

Replacing Damaged Fasteners

• To prevent damage, avoid setting the thermal solution with the prongs down

− Set on heatsink side or with fan down

• The plastic fasteners on the heatsink can be replaced.

− Use Shop Intel to order spare fasteners

− http://www.shop-intel.com

• To remove a damaged fastener

Note: Protective gloves are not required for this procedure

− Rotate the black pin counterclockwise until it “snaps”. There will be some resistance

− Remove the black pin from the white prong

− Tilt the white prong to remove it from the heatsink leg

Avoid damage, avoid placing
prongs on hard surface

16

Damaged. Attempts to
straighten not recommended

Tilt to remove

Replacing Fasteners

• To replace the fastener

− Start with the white prong

− Note the “keying” notch feature

− Tilt the prong to insert into the heatsink leg.

− Holding the white prong without bending it, push the black pin on from the bottom until you hear

a single “click”

Replacement

Tilt to insert

17

Click

Note: The black pin and white prong will only “snap” on in one orientation

− Check to ensure the black pin is rotated properly for installation with the slot perpendicular to the

heatsink

2-4 Install Memory

This motherboard provides two 184-pin DUAL INLINE MEMORY MODULES (DIMM)
sites for memory expansion available from minimum memory size of 64MB to maximum
memory size of 2.0GB DDR SDRAM.

Valid Memory Configurations

Bank 184-Pin DIMM PCS Total Memory

Bank 0, 1 (DIMM1) DDRDDR266/DDR333/DDR400

DDR SDRAM Module

Bank 2, 3 (DIMM2) DDRDDR266/DDR333/DDR400

DDR SDRAM Module

X1

X1

64MB∼1.0GB

64MB∼1.0GB

For Dual channel Limited!

Dual channel function only supports when 2 DIMM Modules plug in both DIMM1 &

1.

DIMM2.

DIMM1 & DIMM2 must be the same type, same size, same frequency for dual channel

2.

function.

Generally, installing DDR SDRAM modules to your motherboard is very easy, you can refer
to figure 2-4 to see what a 184-Pin DDR266/DDR333/DDR400 DDR SDRAM module looks
like.

DIMM2 (BANK2+BANK3)

DIMM1 (BANK0+BANK1)

Figure 2-4

18

NOTE! When you install DIMM module fully into the DIMM socket the eject tab should be

locked into the DIMM module very firmly and fit into its indention on both sides.

WARNING! For the DDR SDRAM CLOCK is set at 200MHz, use only DDR400-compliant DDR

Modules. When this motherboard operate at 200Mhz, most system will not even
boot if non-compliant modules are used because of the strict timing issues, if your
SDR Modules are not DDR400-compliant, set the DDR SDRAM clock to 133MHz
to ensure system stability.

2-5 Expansion Cards

WARNING! Turn off your power when adding or removing expansion cards or other system

components. Failure to do so may cause severe damage to both your motherboard
and expansion cards.

2-5-1 Procedure For Expansion Card Installation

1. Read the documentation for your expansion card and make any necessary hardware or

software setting for your expansion card such as jumpers.

2. Remove your computer’s cover and the bracket plate on the slot you intend to use.

3. Align the card’s connectors and press firmly.

4. Secure the card on the slot with the screen you remove above.

5. Replace the computer system’s cover.

6. Set up the BIOS if necessary.

7. Install the necessary software driver for your expansion card.

2-5-2 Assigning IRQs For Expansion Card

Some expansion cards need an IRQ to operate. Generally, an IRQ must exclusively assign to
one use. In a standard design, there are 16 IRQs available but most of them are already in use.

Standard Interrupt Assignments

IRQ Priority Standard function

0 N/A System Timer
1 N/A Keyboard Controller
2 N/A Programmable Interrupt
3 * 8 Communications Port (COM2)
4 * 9 Communications Port (COM1)
5 * 6 Sound Card (sometimes LPT2)
6 * 11 Floppy Disk Controller
7 * 7 Printer Port (LPT1)
8 N/A System CMOS/Real Time Clock

9 * 10 ACPI Mode when enabled
10 * 3 IRQ Holder for PCI Steering
11 * 2 IRQ Holder for PCI Steering
12 * 4 PS/2 Compatible Mouse Port
13 N/A Numeric Data Processor
14 * 5 Primary IDE Channel
15 * 1 Secondary IDE Channel

* These IRQs are usually available for ISA or PCI devices.

19

2-5-3 Interrupt Request Table For This Motherboard

Interrupt request are shared as shown the table below:

INT A INT B INT C INT D INT E INT F INT G INT H
Slot 1
Slot 2
Slot 3

Onboard VGA

Onboard LAN
Onboard USB 1
Onboard USB 2
Onboard USB 3
Sound

√

√

√

√

√

√

√

√

√

IMPORTANT!

If using PCI cards on shared slots, make sure that the drivers support
“Shared IRQ” or that the cards don’t need IRQ assignments. Conflicts will
arise between the two PCI groups that will make the system unstable or
cards inoperable.

2-6 Connectors, Headers

2-6-1 Connectors

(1) Power Connector (24-pin block) : ATXPWR24

ATX Power Supply connector. This is a new defined 24-pins connector that usually

comes with ATX case. The ATX Power Supply allows to use soft power on momentary
switch that connect from the front panel switch to 2-pins Power On jumper pole on the
motherboard. When the power switch on the back of the ATX power supply turned on,
the full power will not come into the system board until the front panel switch is
momentarily pressed. Press this switch again will turn off the power to the system
board.

** We recommend that you use an ATX 12V Specification 2.0-compliant power supply

unit (PSU) with a minimum of 350W power rating. This type has 24-pin and 4-pin
power plugs.

** If you intend to use a PSU with 20-pin and 4-pin power plugs, make sure that the 20-pin

power plug can provide at least 15A on +12V and the power supply unit has a minimum
power rating of 350W. The system may become unstable or may not boot up if the
power is inadequate.

ROW1 ROW2

ROW1 ROW2

Pin 1

20-Pin

Pin 1

24-Pin

PIN ROW1 ROW2

1 3.3V 3.3V

2 3.3V -12V

3 GND GND

4 5V Sof t Power On

5 GND GND

6 5V GND

7 GND GND

8 Power O K -5V

9 +5V (for Soft Logic) +5V

10 +12V +5V

11 +12V +5V

12 +3V GND

20

(2) ATX 12V Power Connector (4-pin block) : ATX12V

This is a new defined 4-pins connector that usually comes with ATX Power Supply. The

ATX Power Supply which fully support Pentium 4 processor must including this
connector for support extra 12V voltage to maintain system power consumption.
Without this connector might cause system unstable because the power supply can not
provide sufficient current for system.

Pin 1

(3) USB Port connector: USB1, UL_B (USB)

The connectors are 4-pin connector that connect USB devices to the system board.

(4) LAN Port connector: LAN (for 865GVBMS)

This connector is standard RJ45 connector for Network connector.

(5) PS/2 Mouse & PS/2 Keyboard Connector: KB (PS2 KB/MOUSE)

The connectors for PS/2 keyboard and PS/2 Mouse.

(6) Parallel Port Connector (25-pin female): PARALLEL

Parallel Port connector is a 25-pin D-Subminiature Receptacle connector. The On­board Parallel Port can be disabled through the BIOS SETUP. Please refer to Chapter 3
“INTEGRATED PERIPHERALS SETUP” section for more detail information.

(7) Audio Line-In, Lin-Out, MIC Connector : CN1

This Connector are 3 phone Jack for LINE-OUT, LINE-IN, MIC

Line-out :
Line-in :

Audio input to sound chip

MIC :

Audio output to speaker

Microphone Connector

(8) Serial Port COM1: COM1

COM1 is the 9-pin D-Subminiature mail connector. The On-board serial port can be
disabled through BIOS SETUP. Please refer to Chapter 3 “INTEGRATED
PERIPHERALS SETUP” section for more detail information

(9)

VGA Connector (15-pin D-Sub) Connector: VGA

VGA is the 15-pin D-Subminiature female connector for display monitor.

21

PS/2 Keyboard

COM1

USB1 PS/2 Mouse PRINT

VGA

LAN

USB

(10) Floppy drive Connector (34-pin block): FDD

This connector supports the provided floppy drive ribbon cable. After connecting the single
plug end to motherboard, connect the two plugs at other end to the floppy drives.

FDD

Pin 1

Floppy Drive Connector

MIC

LINE-IN

LINE-OUT

(11) Primary IDE Connector (40-pin block): IDE1

This connector supports the provided IDE hard disk ribbon cable. After connecting the

single plug end to motherboard, connect the two plugs at other end to your hard disk(s). If
you install two hard disks, you must configure the second drive to Slave mode by setting its
jumpers accordingly. Please refer to the documentation of your hard disk for the jumper
settings.

(12) Secondary IDE Connector (40-pin block): IDE2

This connector connects to the next set of Master and Slave hard disks. Follow the same

procedure described for the primary IDE connector. You may also configure two hard
disks to be both Masters using one ribbon cable on the primary IDE connector and another
ribbon cable on the secondary IDE connector.

IDE2

Pin 1

IDE1

Pin 1

22

• Two hard disks can be connected to each connector. The first HDD is referred to as the

“Master” and the second HDD is referred to as the “Slave”.

• For performance issues, we strongly suggest you don’t install a CD-ROM or DVD-ROM

drive on the same IDE channel as a hard disk. Otherwise, the system performance on this
channel may drop.

(13) Serial-ATA Port connector: SATA1/SATA2

This connector support the provided Serial ATA IDE hard disk cable to connecting the
motherboard and serial ATA hard disk.

SATA2

SATA1

Pin 1

On Chip Serial ATA

Serial-ATA Port Connector

2-6-2 Headers

(1) Line-Out, MIC Header (9-pin): AUDIO

This header connect to Front Panel Line-out, MIC connector with cable.

L

AUDIO

Pin 1

Line-Out, MIC Headers

(2) USB Port Connector/Headers (9-pin) : USB2, USB3

The USB2, USB3 is for internal connecting USB device directly. The USB2 header is
used for connecting the additional USB port plug. By attaching an option USB cable,
your can be provided with two additional USB plugs affixed to the back panel.

R

_

_

GND

RET

RET

VCC

_

_

_

_

AUD

AUD

AUD

AUD

2

MIC

_

AUD

_

_

BIAS

MIC

AUD

R

_

_

FPOUT

_

AUD

ON

HP

10

L

_

FPOUT

_

AUD

9

23

OC

VCC

GND

DATA

-

+DATA

VCC

GND

DATA

-

+DATA

USB3

Pin 1

VCC

DATA

-

+DATA

VCC

DATA

-

+DATA

USB2

OC

GND

Pin 1

GND

USB Port Headers

(3) Speaker connector: SPEAK

This 4-pin connector connects to the case-mounted speaker. See the figure below.

(4) Power LED: PWRLED

The Power LED is light on while the system power is on. Connect the Power LED
from the system case to this pin.

(5) IDE Activity LED: HD LED

This connector connects to the hard disk activity indicator light on the case.

(6) Reset switch lead: RESET

This 2-pin connector connects to the case-mounted reset switch for rebooting your
computer without having to turn off your power switch. This is a preferred method of
rebooting in order to prolong the lift of the system’s power supply. See the figure
below.

(7) Power switch: PWR BTN

This 2-pin connector connects to the case-mounted power switch to power ON/OFF the
system.

PWRLED

Pin 1

Pin 1

System Case Connections

(8) FAN Headers (4-pin) : CPUFAN
FAN Headers (3-pin) : SYSFAN1, SYSFAN2

These connectors support cooling fans of 350mA (4.2 Watts) or less, depending on the
fan manufacturer, the wire and plug may be different. The red wire should be positive,
while the black should be ground. Connect the fan’s plug to the board taking into
consideration the polarity of connector.

PWRBTN

PWR LED

GND

VCC5

PWRLED

VCC5

HDDLE

HDLED

PWRBTN

NC

GND

RSTSW

RESET

JW FP SPEAK

Pin 1

NC

GND

VCC5

SPKR

24

CPUFAN

SYSFAN1

SYSFAN2

4

1

1

3

1 3

FAN Headers

(9) IR infrared module Headers (5-pin) : IR

This connector supports the optional wireless transmitting and receiving infrared
module. You must configure the setting through the BIOS setup to use the IR function.

IR infrared module Headers

(10) CD Audio-In Headers (4-pin) : CDIN

CDIN are the connectors for CD-Audio Input signal. Please connect it to CD-ROM
CD-Audio output connector.

Pin 1

CDIN

IR

2

4

NC

GND

VCC5

IRRX

6

5

IRTX

1

CD Audio-In Headers

25

2-7 Starting Up Your Computer

1. After all connection are made, close your computer case cover.

2. Be sure all the switch are off, and check that the power supply input voltage is set to

proper position, usually in-put voltage is 220V∼240V or 110V∼120V depending on your
country’s voltage used.

3. Connect the power supply cord into the power supply located on the back of your system

case according to your system user’s manual.

4. Turn on your peripheral as following order:

a. Your monitor.
b. Other external peripheral (Printer, Scanner, External Modem etc…)
c. Your system power. For ATX power supplies, you need to turn on the power supply

and press the ATX power switch on the front side of the case.

5. The power LED on the front panel of the system case will light. The LED on the monitor

may light up or switch between orange and green after the system is on. If it complies
with green standards or if it is has a power standby feature. The system will then run
power-on test. While the test are running, the BIOS will alarm beeps or additional
message will appear on the screen.

If you do not see any thing within 30 seconds from the time you turn on the power. The
system may have failed on power-on test. Recheck your jumper settings and connections
or call your retailer for assistance.

Beep Meaning

One short beep when displaying logo No error during POST

Long beeps in an endless loop No DRAM install or detected

One long beep followed by three short
beeps

High frequency beeps when system is
working

Video card not found or video card memory
bad

CPU overheated

System running at a lower frequency

6. During power-on, press <Delete> key to enter BIOS setup. Follow the instructions in

BIOS SETUP.

7.

Power off your computer:

You must first exit or shut down your operating system
before switch off the power switch. For ATX power supply, you can press ATX power
switching after exiting or shutting down your operating system. If you use Windows 9X,
click

“Start”

button, click

“Shut down”

and then click

“Shut down the computer?”

The power supply should turn off after windows shut down.

26

Chapter 3

Introducing BIOS

The BIOS is a program located on a Flash Memory on the motherboard. This program is a
bridge between motherboard and operating system. When you start the computer, the BIOS
program gain control. The BIOS first operates an auto-diagnostic test called POST (power on
self test) for all the necessary hardware, it detects the entire hardware device and configures
the parameters of the hardware synchronization. Only when these tasks are completed done it
gives up control of the computer to operating system (OS). Since the BIOS is the only
channel for hardware and software to communicate, it is the key factor for system stability,
and in ensuring that your system performance as its best.

In the BIOS Setup main menu of Figure 3-1, you can see several options. We will explain
these options step by step in the following pages of this chapter, but let us first see a short
description of the function keys you may use here:

• Press <Esc> to quit the BIOS Setup.

• Press ↑↓←→ (up, down, left, right) to choose, in the main menu, the option you want to

confirm or to modify.

• Press <F10> when you have completed the setup of BIOS parameters to save these

parameters and to exit the BIOS Setup menu.

• Press Page Up/Page Down or +/– keys when you want to modify the BIOS parameters for

the active option.

3-1 Entering Setup

Power on the computer and by pressing <Del> immediately allows you to enter Setup.
If the message disappears before your respond and you still wish to enter Setup, restart the
system to try again by turning it OFF then ON or pressing the “RESET” button on the system
case. You may also restart by simultaneously pressing <Ctrl>, <Alt> and <Delete> keys. If
you do not press the keys at the correct time and the system does not boot, an error message
will be displayed and you will again be asked to

Press <F1> to continue, <Ctrl-Alt-Esc> or <Del> to enter Setup

3-2 Getting Help

Main Menu

The on-line description of the highlighted setup function is displayed at the bottom of the
screen.

Status Page Setup Menu/Option Page Setup Menu

Press F1 to pop up a small help window that describes the appropriate keys to use and the
possible selections for the highlighted item. To exit the Help Window, press <Esc>.

27

3-3 The Main Menu

Once you enter Award BIOS CMOS Setup Utility, the Main Menu (Figure 3-1) will appear
on the screen. The Main Menu allows you to select from fourteen setup functions and two
exit choices. Use arrow keys to select among the items and press <Enter> to accept or enter
the sub-menu.

CMOS Setup Utility – Copyright(C) 1984-2004 Award Software

Standard CMOS Features

Advanced BIOS Features

Advanced Chipset Features

Integrated Peripherals

Power Management Setup

PnP/PCI Configurations

PC Health Status

Esc : Quit

F10 : Save & Exit Setup

Time, Date, Hard Disk Type...

Figure 3-1

Miscellaneous Control

Load optimized Defaults

Load Standard Defaults

Set Supervisor Password

Set User Password

Save & Exit Setup

Exit Without Saving

↑↓→←

: Select Item

Standard CMOS Features

Use this Menu for basic system configurations.

Advanced BIOS Features

Use this menu to set the Advanced Features available on your system.

Advanced Chipset Features

Use this menu to change the values in the chipset registers and optimize your system’s
performance.

Integrated Peripherals

Use this menu to specify your settings for integrated peripherals.

Power Management Setup

Use this menu to specify your settings for power management.

PnP/PCI configurations

This entry appears if your system supports PnP/PCI.

PC Health Status

This entry shows your PC health status.

Miscellaneous Control

Use this menu to specify your settings for Miscellaneous control.

28

Load Optimized Defaults

Use this menu to load the BIOS default values that are settings for optimal performances
system operations.

Load Standard Defaults

Use this menu to load the BIOS default values that are factory settings for the stable
performance system operation.

Set Supervisor/User Password

Use this menu to set User and Supervisor Passwords.

Save & Exit Setup

Save CMOS value changes to CMOS and exit setup.

Exit Without Saving

Abandon all CMOS value changes and exit setup.

3-4 Standard CMOS Features

The items in Standard CMOS Setup Menu are divided into several categories. Each category
includes no, one or more than one setup items. Use the arrow keys to highlight the item and
then use the <PgUp> or <PgDn> keys to select the value you want in each item.

CMOS Setup Utility – Copyright(C) 1984-2004 Award Software

Standard CMOS Features

Date (mm:dd:yy) Thu, Nov, 25 2004
Time (hh:mm:ss) 09 : 44 : 35

> IDE Primary Master Press Enter None
> IDE Primary Slave Press Enter None
> IDE Secondary Master Press Enter None
> IDE Secondary Slave Press Enter None

Drive A 1.44M, 3.5 in.

Video EGA/VGA
Halt On All,But Keyboard

Base Memory 640K
Extended Memory 56320K
Total Memory 57344K

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

Item Help

Menu Level >

Change the day, month,
year and century

Date

The date format is <day><month><date><year>.

Day of the week, from Sun to Sat, determined by BIOS. Read-only.

Day
Month
Date
Year

The month from Jan. through Dec.

The date from 1 to 31 can be keyed by numeric function keys.

The year depends on the year of the BIOS.

29

Time

The time format is <hour><minute><second>.

Primary Master/Primary Slave
Secondary Master/Secondary Slave

Press PgUp/<+> or PgDn/<–> to select Manual, None, Auto type. Note that the specifications of
your drive must match with the drive table. The hard disk will not work properly if you enter
improper information for this category. If your hard disk drive type is not matched or listed, you
can use Manual to define your own drive type manually.

If you select Manual, related information is asked to be entered to the following items. Enter the
information directly from the keyboard. This information should be provided in the
documentation from your hard disk vendor or the system manufacturer.
If the controller of HDD interface is SCSI, the selection shall be “None”.
If the controller of HDD interface is CD-ROM, the selection shall be “None”

Access Mode
Cylinder
Head
Precomp
Landing Zone
Sector

number of sectors

The settings are Auto Normal, Large, and LBA.

number of cylinders

number of heads

write precomp

landing zone

3-5 Advanced BIOS Features

CMOS Setup Utility – Copyright(C) 1984-2004 Award Software

Advanced BIOS Features

Anti-Virus Protection Disabled
CPU L1 & L2 Cache Enabled
Hyper Threading Technology Disabled
Quick Power On Self Test Enabled
Hard Disk Boot Priority Press Enter
First Boot Device Floppy
Second Boot Device HDD 0
Third Boot Device CDROM
Boot other Device Enabled
Boot Up Floppy Seek Enabled
Boot Up NumLock Status On
Gate A20 Option Fast
Typematic Rate Setting Disabled
Typematic Rate (Chars/Sec) 6
Typematic Delay (Msec) 250
Security Option Setup
APIC Mode Disabled
MPS Version Control For OS 1.4
OS Select For DRAM > 64MB Non-OS2
Report NO FDD For Windows Yes

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

Item Help

Menu Level >

30

Anti-Virus Protection

Allows you to choose the VIRUS Warning feature for IDE Hard Disk boot sector protection.
If this function is enabled and someone attempt to write data into this area, BIOS will show a
warning message on screen and alarm beep.

Disabled

(default) No warning message to appear when anything attempts to access the

boot sector or hard disk partition table.

Enabled

Activates automatically when the system boots up causing a warning
message to appear when anything attempts to access the boot sector
of hard disk partition table.

CPU Internal Cache

The default value is Enabled.

Enabled
Disabled

(default) Enable cache

Disable cache

Note: The internal cache is built in the processor.

External Cache

Choose Enabled or Disabled. This option enables the Level 2 cache memory.

CPU L2 Cache ECC Checking

Choose Enabled or Disabled. This option enables the Level 2 cache memory ECC (error
check correction).

Quick Power On Self Test

This category speeds up Power On Self Test (POST) after you power on the computer. If this
is set to Enabled. BIOS will shorten or skip some check items during POST.

Enabled
Disabled

(default) Enable quick POST

Normal POST

First/Second/Third/Fourth Boot Device

The BIOS attempts to load the operating system from the devices in the sequence selected in
these items. The settings are Floppy, LS/ZIP, HDD-0/HDD-1/HDD-3, SCSI, CDROM, LAD
and Disabled.

Boot Up Floppy Seek

During POST, BIOS will determine if the floppy disk drive installed is 40 or 80 tracks. 360K
type is 40 tracks while 760K, 1.2M and 1.44M are all 80 tracks.

Boot Up NumLock Status

The default value is On.

(default)

On
Off

Keypad is numeric keys.
Keypad is arrow keys.

Gate A20 Option

Normal

(default) The A20 signal is controlled by port 92 or chipset specific method.

Fast

The A20 signal is controlled by keyboard controller or chipset hardware.

Typematic Rate Setting

Keystrokes repeat at a rate determined by the keyboard controller. When enabled, the
typematic rate and typematic delay can be selected. The settings are: Enabled/Disabled.

31

Typematic Rate (Chars/Sec)

Sets the number of times a second to repeat a keystroke when you hold the key down. The
settings are: 6, 8, 10, 12, 15, 20, 24, and 30.

Typematic Delay (Msec)

Sets the delay time after the key is held down before is begins to repeat the keystroke. The
settings are 250, 500, 750, and 1000.

Security Option

This category allows you to limit access to the system and Setup, or just to Setup.

System

The system will not boot and access to Setup will be denied if the
correct password is not entered at the prompt.

Setup

(default) The system will boot, but access to Setup will be denied if the correct

password is not entered prompt.

OS Select For DRAM > 64MB

Allows OS2 to be used with >64MB or DRAM. Settings are Non-OS/2 (default) and OS2.
Set to OS/2 if using more than 64MB and running OS/2.

3-6 Advanced Chipset Features

The Advanced Chipset Features Setup option is used to change the values of the chipset
registers. These registers control most of the system options in the computer.

CMOS Setup Utility – Copyright(C) 1984-2004 Award Software

Advanced Chipset Features

> DRAM Timing Settings Press Enter
System BIOS Cacheable Enabled
Video BIOS Cacheable Enabled
Memory Hole At 15M-16M Disabled
AGP Aperture Size 128MB
On-Chip VGA Enabled
On-Chip Frame Buffer Size 16MB

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

DRAM Timing Settings

Please refer to section 3-6-1

Item Help

Menu Level >

System BIOS Cacheable

Selecting Enabled allows caching of the system BIOS ROM at F0000h-FFFFFh, resulting in
better system performance. However, if any program writes to this memory area, a system
error may result. The settings are: Enabled and Disabled.

32

Video BIOS Cacheable

Select Enabled allows caching of the video BIOS, resulting in better system performance.
However, if any program writes to this memory area, a system error may result. The settings
are: Enabled and Disabled.

Memory Hole At 15M-16M

You can reserve this area of system memory for ISA adapter ROM. When this area is
reserved, it cannot be cached. The user information of peripherals that need to use this area of
system memory usually discusses their memory requirements. The settings are: Enabled and
Disabled.

3-6-1 DRAM Timing Settings

CMOS Setup Utility – Copyright(C) 1984-2004 Award Software

DRAM Timing Settings

Auto Configuration Standard
SDRAM CAS Latency Time 2.5
SDRAM Cycle Time 7
SDRAM RAS# to CAS# Delay 3
SDRAM RAS# Precharge Time 3

Item Help

Menu Level >>

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

SDRAM CAS Latency Time

When synchronous DRAM is installed, the number of clock cycles of CAS latency depends
on the DRAM timing. The settings are: 2T and 2.5T.

Note: Change these settings only if you are familiar with the chipset.

SDRAM RAS# to CAS# Delay

This field let’s you insert a timing delay between the CAS and RAS strobe signals, used when
DRAM is written to, read from, or refreshed. Fast gives faster performance; and Slow gives
more stable performance. This field applies only when synchronous DRAM is installed in the
system. The settings are: 2T, 3T and 4T.

SDRAM RAS# Precharge Time

If an insufficient number of cycles is allowed for the RAS to accumulate its charge before
DRAM refresh, the refresh may be incomplete and the DRAM may fail to retain date. Fast
gives faster performance; and Slow gives more stable performance. This field applies only
when synchronous DRAM is installed in the system. The settings are: 2T, 3T and 4T.

33

3-7 Integrated Peripherals

CMOS Setup Utility – Copyright(C) 1984-2004 Award Software

Integrated Peripherals

> Onboard IDE Function Press Enter
> Onboard Device Function Press Enter
> Onboard Super IO Function Press Enter
Init Display First PCI Slot
Power Loss Function Always Off

Item Help

Menu Level >

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

Onboard IDE Function

Please refer to section 3-7-1

Onboard Device Function

Please refer to section 3-7-2

Onboard Super IO Function

Please refer to section 3-7-3

Init Display First

This item allows you to decide to activate whether PCI Slot or AGP VGA first. The settings
are: PCI Slot, AGP Slot.

3-7-1 Onboard IDE Function

CMOS Setup Utility – Copyright(C) 1984-2004 Award Software

Onboard IDE Function

OnChip Primary PCI IDE Enabled
OnChip Secondary PCI IDE Enabled
Primary Master PIO Auto
Primary Slave PIO Auto
Secondary Master PIO Auto
Secondary Slave PIO Auto
Primary Master UDMA Auto
Primary Slave UDMA Auto
Secondary Master UDMA Auto
Secondary Slave UDMA Auto
IDE 32-bit Transfer Mode Enabled
IDE HDD Block Mode Enabled
Delay For HDD (Secs) 0
On-Chip Serial ATA Disabled
Serial ATA Port1 Mode Primary Master

Item Help

Menu Level >>

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

34

OnChip IDE Primary/Secondary

The integrated peripheral controller contains an IDE interface with support for two IDE channels.
Select

Enabled

to activate each channel separately. The settings are: Enabled and Disabled.

Primary/Secondary Master/Slave PIO

The four IDE PIO (Programmed Input/Output) fields let you set a PIO mode (0-4) for each of the
four IDE devices that the onboard IDE interface supports. Modes 0 through 4 provide
successively increased performance. In Auto mode, the system automatically determines the best
mode for each device. The settings are: Auto, Mode 0, Mode 1, Mode 2, Mode 3, Mode 4.

Primary/Secondary Master/Slave UDMA

Ultra DMA/33 implementation is possible only if your IDE hard drive supports it and the
operating environment includes a DMA driver (Windows 95 OSR2 or a third-party IDE bus
master driver). If your hard drive and your system software both support Ultra DMA/33 and
Ultra DMA/66, select Auto to enable BIOS support. The settings are: Auto, Disabled.

IDE HDD Block Mode

Block mode is also called block transfer, multiple commands, or multiple sector read/write. If
your IDE hard drive supports block mode (most new drives do), select Enabled for automatic
detection of the optimal number of block read/writes per sector the drive can support. The
settings are: Enabled, Disabled.

On-Chip Serial ATA

The settings are: Disabled, Auto, Combined Mode, Enhanced Mode, SATA Only.
Default setting is Auto. Due to the Intel ICH5 Specification limited only provided two controllers.
When plug the Serial ATA hard drive in SATA1 or SATA2 only can support either IDE1 or
IDE2 can works in Windows 9X/ME/2000. But in the Windows XP the OS can support 6 IDE
devices both IDE1, IDE2 and SATA1/SATA2 can works.

3-7-2 Onboard Device Function

CMOS Setup Utility – Copyright(C) 1984-2004 Award Software

Onboard Device Function

AC97 Audio Auto
AC97 Modem Auto
USB Controller Enabled
USB Keyboard Legacy Support Disabled

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

AC97 Audio/AC97 Modem

This item is setting on board AC97 Audio/AC97 Modem enabled/disabled. The settings are:
Enabled, Disabled, Auto.

USB Controller

Select

Enabled

if your system contains a Universal Serial Bus (USB) controller and you have a

USB peripherals. The settings are: Enabled, Disabled.

USB Keyboard Legacy Support

Select

Enabled

if your system contains a Universal Serial Bus (USB) controller and you have a

USB keyboard. The settings are: Enabled, Disabled.

Item Help

Menu Level >>

35

3-7-3 Onboard Super IO Function

CMOS Setup Utility – Copyright(C) 1984-2004 Award Software

Onboard Super IO Function

Onboard FDD Controller Enabled
Onboard Serial Port 1 3F8/IRQ4
Onboard Serial Port 2 Disabled
UART Mode Select Normal
IR2 Duplex Mode Half
Onboard Parallel Port 378/IRQ7
Parallel Mode SPP
ECP Mode Use DMA 3

Item Help

Menu Level >>

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

Onboard FDD Controller

Select Enabled if your system has a floppy disk controller (FDD) installed on the system
board and you wish to use it. If you install add-on FDC or the system has no floppy drive,
select Disabled in this field. The settings are: Enabled and Disabled.

Onboard Serial Port 1/Port 2

Select an address and corresponding interrupt for the first and the second serial ports. The
settings are: 3F8/IRQ4, 2E8/IRQ3, 3E8/IRQ4, 2F8/IRQ3, Disabled, Auto.

UART Mode Select

This item allows you to determine which InfraRed(IR) function of the onboard I/O chip, this
functions uses.

Onboard Parallel Port

There is a built-in parallel port on the on-board Super I/O chipset that Provides Standard, ECP,
and EPP features. It has the following option:

Disabled
(3BCH/IRQ7)/
(278H/IRQ5)/
(378H/IRQ7)

Parallel Port Mode

SPP : Standard Parallel Port
EPP : Enhanced Parallel Port
ECP : Extended Capability Port

Line Printer port 0

Line Printer port 2

Line Printer port 1

SPP/EPP/ECP/ECP+EPP

To operate the onboard parallel port as Standard Parallel Port only, choose “SPP.” To operate the
onboard parallel port in the EPP modes simultaneously, choose “EPP.” By choosing “ECP”, the
onboard parallel port will operate in ECP mode only. Choosing “ECP+EPP” will allow the
onboard parallel port to support both the ECP and EPP modes simultaneously. The ECP mode
has to use the DMA channel, so choose the onboard parallel port with the ECP feature. After
selecting it, the following message will appear: “ECP Mode Use DMA” at this time, the user can
choose between DMA channels 3 to 1. The onboard parallel port is EPP Spec. compliant, so after
the user chooses the onboard parallel port with the EPP function, the following message will be
displayed on the screen: “EPP Mode Select.” At this time either EPP 1.7 spec. or EPP 1.9 spec.
can be chosen.

36

3-8 Power Management Setup

The Power Management Setup allows you to configure your system to most effectively save
energy saving while operating in a manner consistent with your own style of computer use.

CMOS Setup Utility – Copyright(C) 1984-2004 Award Software

Power Management Setup

ACPI Function Enabled
Power Management User Define
Video off Method V/H SYNC+Blank
Video Off In Suspend Yes
Suspend Type Stop Grant
MODEM Use IRQ 3
Suspend Mode Disabled
HDD Power Down Disabled
Soft-off by PWR-BTTN Instant-off
Wake-Up by PCI card Disabled
Power On by Ring Disabled
Resume by Alarm Disabled
X Date (of Month) 0
X Time (hh:mm:ss) 0 : 0 :0
CPU Thermal Management Timer 32 Min

> PM Timer Reload Events Press Enter

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

Item Help

Menu Level >

ACPI Function

This item allows you to Enabled/Disabled the Advanced Configuration and Power Management
(ACPI). The settings are Enabled and Disabled.

Video Off in Suspend

This determines the manner in which the monitor is blanked. The choice are Yes → Video
will off , and No→ Video always On.

Video Off Method

This determines the manner in which the monitor is blanked.

DPMS
Blank Screen
V/H SYNC+Blank

(default) Initial display power management signaling.

This option only writes blanks to the video buffer.

This selection will cause the system to turn off the vertical and

horizontal synchronization ports and write blanks to the video
buffer.

Modem Use IRQ

This determines the IRQ in which the MODEM can use.
The settings are: 3, 4, 5, 7, 9, 10, 11, NA.

Power Button Function

Pressing the power button for more than 4 seconds forces the system to enter the Soft-Off
state. The settings are: Delay 4 Sec, Instant-Off.

Wake-Up by PCI card /Power On by Ring

During Disabled, the system will ignore any incoming call from the PCI card/modem. During
Enabled, the system will boot up if there’s an incoming call from the PCI card /modem.

37

Wake-Up on RTC Alarm

This function is for setting date and time for your computer to boot up. During Disabled, you
cannot use this function. During Enabled, choose the Date and Time Alarm:

Date(of month) Alarm

You can choose which month the system will boot up. Set to 0, to boot every day.

Time(hh:mm:ss) Alarm

You can choose what hour, minute and second the system will boot up.

Note: If you have change the setting, you must let the system boot up until it goes to the
operating system, before this function will work

PM Timer Reload Events

Please refer to section 3-8-1

3-8-1 PM Timer Reload Events

CMOS Setup Utility – Copyright(C) 1984-2004 Award Software

PM Timer Reload Events

Primary IDE 0 Disabled

Primary IDE 1 Disabled
Secondary IDE 0 Disabled
Secondary IDE 1 Disabled
FDD, COM, LPT Port Disabled

PCI PIRQ [A-D] # Disabled

Item Help

Menu Level >>

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

3-9 PnP/PCI Configuration Setup

This section describes configuring the PCI bus system. PCI, or Personal Computer
Interconnect, is a system which allows I/O devices to operate at speeds nearing the speed the

CPU itself uses when communicating with its own special components. This section covers
some very technical items and it is strongly recommended that only experienced users should
make any changes to the default settings.

CMOS Setup Utility – Copyright(C) 1984-2004 Award Software

PnP/PCI Configurations

Reset Configuration Data Disabled

Resources Controlled By Manual
x IRQ Resources Press Enter

PCI/VGA Palette Snoop Disabled
Assign IRQ For VGA Enabled

Item Help

Menu Level >

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

38

Reset Configuration Data

Normally, you leave this field Disabled. Select Enabled to reset Extended System Configuration
Data (ESCD) when you exit Setup if you have installed a new add-on and the system
reconfiguration has caused such a serious conflict that the operating system can not boot. The
settings are: Enabled and Disabled.

Resource Controlled By

The Award Plug and Play BIOS has the capacity to automatically configure all of the boot
and Plug and Play compatible devices. However, this capability means absolutely nothing
unless you are using a Plug and Play operating system such as Windows95/98. If you set
this field to “manual” choose specific resources by going into each of the sub menu that
follows this field (a sub menu is preceded by a “>”).
The settings are: Auto(ESCD), Manual.

IRQ Resources

When resources are controlled manually, assign each system interrupt a type, depending on
the type of device using the interrupt.
Please refer to section 3-9-1

PCI/VGA Palette Snoop

Leave this field at Disabled. The settings are Enabled, Disabled.

3-9-1 IRQ Resources

CMOS Setup Utility – Copyright(C) 1984-2004 Award Software

IRQ Resources

IRQ-3 assigned to PCI Device
IRQ-4 assigned to PCI Device
IRQ-5 assigned to PCI Device
IRQ-7 assigned to PCI Device
IRQ-9 assigned to PCI Device
IRQ-10 assigned to PCI Device
IRQ-11 assigned to PCI Device
IRQ-12 assigned to PCI Device
IRQ-14 assigned to PCI Device
IRQ-15 assigned to PCI Device

Menu Level >>

Item Help

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

39

3-10 PC Health Status

This section shows the Status of you CPU, Fan, Warning for overall system status. This is only
available if there is Hardware Monitor onboard.

CMOS Setup Utility – Copyright(C) 1984-2004 Award Software

PC Health Status

Shutdown Temperature Disabled
Show PC Health in Post Enabled
Current System Temperature 25°C
Current CPU Temperature 38°C
Current CPUFAN Speed 5000 rpm
Current SYSFAN Speed 5000 rpm
Current SYSFAN2 Speed 5000 rpm
Vcore 1.71V
Vcc1.5 1.51V
Vcc3.3 3.31V
+ 5V 4.98V
+12V 12.22V

-12V -12.36V

- 5V -4.99V
VBAT(V) 3.21V
5VSB(V)

5.02V

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

Item Help

Menu Level >

Shutdown Temperature

This item can let users setting the Shutdown temperature, when CPU temperature over this
setting the system will auto shutdown to protect CPU.

Show PC Health in Post

During Enabled, it displays information list below. The choice is either Enabled or Disabled.

Current CPU Temperature/Current System Temp/Current FAN1, FAN2 Speed/Vcore/
Vdd/ 3.3V/+5V/+12V/-12V/VBAT(V)/5VSB(V)

This will show the CPU/FAN/System voltage chart and FAN Speed.

40

3-11 Miscellaneous Control

This section is for setting CPU Frequency/Voltage Control.

CMOS Setup Utility – Copyright(C) 1984-2004 Award Software

Miscellaneous Control

CPU Clock Ratio 8 X
Auto Detect PCI Clk Enabled
Spread Spectrum Disabled
** Current Host Clock is 100MHz **
HOST Clock at Next Boot is 100MHz
** Current DRAM Clock is 133MHz **
DRAM Clock at Next Boot is DDR266
Flash Part Write Protect Enabled

Item Help

Menu Level >

↑↓→←

Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help

F5:Previous Values F6:Optimized Defaults F7:Standard Defaults

Auto Detect PCI Clk

This item allows you to enable/disable auto detect PCI Clock.
The settings are: Enabled, Disabled.

Spread Spectrum

This item allows you to set the CPU Host/PCI clock and Spread Spectrum.
The settings are: Enabled, Disabled.

Host Clock at Next Boot is

This item allows you to select CPU frequency step by step increasing.
The choice are: 400MHz CPU----100MHz~350MHz, 533MHz CPU---133MHz~350MHz
800MHz CPU---200MHz~350MHz

DRAM Clock at Next Boot is

This item allows you select the DRAM Clock for DDR266/DDR333/DDR400. The setting
are:
DDR266 for P4/400MHz CPU, DDR266/DDR333 for P4/533MHz CPU, DDR266/DDR333
/DDR400 for P4/800MHz CPU

Flash Part Write Protect

This item allows you protect your BIOS chip from Virus destroy data. When Flash BIOS you
have Disabled this item.

41

3-12 Load Standard/Optimized Defaults

Load Standard Defaults

When you press <Enter> on this item, you get confirmation dialog box with a message similar
to:

Load Standard Defaults (Y/N)? N

Pressing <Y> loads the BIOS default values for the most stable, minimal-performance system
operations.

Load Optimized Defaults

When you press <Enter> on this item, you get a confirmation dialog box with a message
similar to:

Load Optimized Defaults (Y/N)? N

Pressing <Y> loads the default values that are factory settings for optimal performance
system operations.

3-13 Set Supervisor/User Password

You can set either supervisor or user password, or both of them. The differences are:

Supervisor password: Can enter and change the options of the setup menus.
User password: Can only enter but do not have the right to change the options of

the setup menus. When you select this function, the following
message will appear at the center of the screen to assist you in
creating a password.

ENTER PASSWORD:

Type the password, up to eight characters in length, and press <Enter>. The password typed
now will clear any previously entered password from CMOS memory. You will be asked to
confirm the password. Type the password again and press <Enter>. You may also press
<Esc> to abort the selection and not enter a password.

To disable a password, just press <Enter> when you are prompted to enter the password. A
message will confirm that the password will be disabled. Once the password is disabled, the
system will boot and you can enter Setup freely.

PASSWORD DISABLED.

When a password has been enabled, you will be prompted to enter it every time you try to
enter Setup. This prevents an unauthorized person from changing any part of your system
configuration.

Additionally, when a password is enabled, you can also require the BIOS to request a
password every time your system is rebooted. This would prevent unauthorized use of your
computer.

You determine when the password is required within the BIOS Features Setup Menu and its
Security option. If the Security option is set to “System”, the password will be required both
at boot and at entry to Setup. If set to “Setup”, prompting only occurs when trying to enter
Setup.

42

Chapter 4

DRIVER & FREE PROGRAM INSTALLATION

Check your package and there is A MAGIC INSTALL CD included. This CD consists of all
DRIVERS you need and some free application programs and utility programs. In addition,
this CD also include an auto detect software which can tell you which hardware is installed,
and which DRIVERS needed so that your system can function properly. We call this auto
detect software MAGIC INSTALL.

MAGIC INSTALL Supports WINDOWS 98SE/ME/NT4.0/2000/XP

Insert CD into your CD-ROM drive and the MAGIC INSTALL Menu should appear as below.
If the menu does not appear, double-click MY COMPUTER / double-click CD-ROM drive or
click START / click RUN / type X:\SETUP.EXE (assuming X is your CD-ROM drive).

From MAGIC INSTALL MENU you may make 10 selections:

1. INF install Intel 865GV chipset system driver

2. VGA install Intel 865GV VGA driver

3. SOUND install ALC AC97’ Codec Audio driver

4. LAN install VIA 6105/6106S LAN Controller driver (only for 865GVBMS)

5. USB2.0 install USB 2.0 driver

6. PC-CILLIN install PC-CILLIN2004 anti-virus program

7. PC-HEALTH install Intel Hardware Doctor Utility

8. MBIOS&DX9 install BIOS Live Update Utility and Microsoft DirectX 9 driver

9. BROWSE CD to browse the contents of the CD

10. EXIT to exit from MAGIC INSTALL menu

43

4-1 INF install Intel 865GV chipset system driver

After you have completed the installation of your operation system (WINDOWS 98SE). You
will find an UNKNOWN DEVICE in the device manager (START/SETTING/CONTROL
PANEL/ SYSTEM/DEVICE MANAGER). You have to install INF driver as shown below:

1. Click INF in the MAGIC INSTALL MENU 2. Click NEXT when Chipset Software Install

Utility appears

3. This license agreement appear , click Yes , the

readme information appear , click Next

NOTE: MAGIC INSTALL will auto detect file path X:\INTEL865\INF\SETUP.EXE
This driver supports WINDOWS 98SE/ME/2000/XP
(NT4.0 do not require)

4. Select if you want computer re-started click

Finish

4-2 VGA install Intel 865GV VGA Driver

1. Click VGA when MAGIC INSTALL

MENU appears

2. Click NEXT When Intel (R) Extreme

Graphics Driver Software Setup appear

44

3. Click YES, This is Announce CopyRight 4. If You Want Re-start Computer , Click

FINISH

4-3 SOUND install ALC AC97’ Codec Audio Driver

1. Click SOUND when MAGIC INSTALL

MENU appears

3. Click Finish and Restart Windows

2. Then auto detect operation system language

edition, click OK, start to install DRIVER

4. Click Start→Program→Avance Sound
Manager→AvRack. Then AVRACK Windows
appears

45

5. Sound Effect select and KaraOK Mode

6. Manual Sound Effect Setting

Function

Note: The path of the file

For WIN98/NT4.0/WIN2K/XP is X:\CODEC\ALC\SETUP.EXE

Note: In Win2K/WinME users have to click Control Panel\System\Device Manager\

DVD\CD-ROM drives to Enabled digital CD Audio for the CD-ROM Device
when use the SPDIF-Out digital signal.

4-4 LAN install VIA 6105/6106S LAN Controller Driver

(only for 865GVBMS)

WINDOWS 98SE/98ME/2000/XP Setup

1. Click LAN when Magic Install Menu appear 2. Install VIA VT6105 PCI 10/100M Fast
Ethernet Driver

3. Select YES and Restart your computer

X:\VIALAN\WIN98 (If OS is win9X)

46

4-5 USB2.0 install Intel USB2.0 Driver

Windows 98SE/ME USB 2.0 Driver installation

1. Click USB2.0 when Magic Install Menu

appear

Windows 2000/XP USB 2.0 Driver installation

Windows 2000

Mothed1 Start Windows 2000 OS and Internet Connect, Select "Windows Update",
Select Driver Update, Install Windows2000 USB2.0 Driver
Mothed2 Install Windows 2000 Service Pack 4 or later

Windows XP

Install Windows XP Service Pack 1 or later

2. This license agreement appear, click Yes, then finish
install driver , click Close and restart your computer

4-6 PC-HEALTH install Intel Hardware Doctor Utility

1. Click PC-HEALTH when MAGIC INSTALL

MENU appears

2. Click Next when Install shield wizard Window

appears, Choose destination location and click
Next, when the start copy file windows appear,
click next

47

3. Select Finish after setup complete 4. Execute MY GUARD utility, On-time

Monitoring your system health

NOTE: MAGIC INSTALL will auto detect file path X:\INTEL865\HEALTH\SETUP.EXE
This driver supports WINDOWS 95/98/98SE/NT4.0/2000

4-7 MBIOS&DX9 Install BIOS Live Update Utility and DIRECTX9

1. Click Magic BIOS when Magic Install MENU

appears

2. Click Next to install the Magic BIOS in

Destination Folder

3. After finish Setup you will have a Magic

BIOS icon in your screen

4. Double click the Magic BIOS icon you will

have this picture, choose from internet you can
upgrade BIOS On-line

48

5. When On-line update BIOS the program will

auto-check your BIOS version

6. Click Next if you need update BIOS, after

upgrade BIOS, the system will clear CMOS
and automatically restart

7. Click Yes if you want to update the BIOS

otherwise choose No to exit

8. When System programming BIOS don’t turn

9. When choose From Local Driver to update BIOS,

you must have the correct BIOS file in your Local
Driver

off power, after finish update BIOS, the system
will clear CMOS and automatically Restart

10. Choose the correct BIOS file to update

BIOS

49

4-8 PC-CILLIN Install PC-CILLIN 2004 Anti-virus program

1. Click PC-CILLIN when MAGIC INSTALL

MENU appear

2. Click NEXT when the "Trend Micro internet

security" installshield wizard windows appear

3. This is license agreement, select "I Accept

the terms" and Click NEXT

4. Click NEXT and Enter your Customer

Information, Click NEXT or choose Change
to change the path for the file to be stored

5. Click INSTALL, Start to install the software 6. Setup Complete and click FINISH

50

7. After PC-CILLIN 2004 complete, Please

register your information and we recommend
select update item to download newest engine
code and virus code

Note : Please install ACROBAT READER, Before you read PC-CILLIN 2004 User

Manual, the path at X:\acrobat\adberdr6_enu_full.exe

4-9 HOW TO UPDATE BIOS

Before update BIOS users have to “Disable”, “Flash Part Write Protect” item which in
“Miscellaneous Control” of BIOS SETUP. Otherwise the system the will not allow you to
upgrade BIOS by Award Flash Utility.

Method 1. Use “Magic BIOS” update BIOS in Windows 98 (refer page 48)
Method 2. In DOS Mode

STEP 1. Prepare a boot disc. (you may make one by click START click RUN type SYS A:

click OK)

STEP 2. Copy utility program to your boot disc. You may copy from DRIVER CD

X:\FLASH\AWDFLASH.EXE or download from our web site.

STEP 3. Copy latest BIOS for 865GVBMS/865GVBM from our web site to your boot disc.

STEP 4. Insert your boot disc into A:,

start the computer, type “Awdflash A:\865GVBMSAxxx.BIN /SN/PY/CC/R”
865GVBMSAxxx.BIN is the file name of latest BIOS it can be 865GVBMSA03.BIN

or 865GVBMSA02.BIN
SN means don’t save existing BIOS data
PY means renew existing BIOS data
CC means clear existing CMOS data
R means restart computer

STEP 5. Push ENTER and the BIOS will be updated, computer will be restarted

automatically.

51