Jetway 848PDAR1A User Manual
848PDA/848PDAP/848PDAG
USER'S MANUAL
M/B For Socket 478 Pentium 4 Processor
NO. G03-848PDA
Rev:1.0
Release date: Oct’ 2003
Trademark:
* Specifications and Information contained in this documentation are furnished for information use only, and are
subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
USER’S NOTICE............................................................................................................... ii
MANUAL REVISION INFORMATION............................................................................... ii
COOLING SOLUTIONS ................................................................................................... ii
CHAPTER 1 INTRODUCTION OF 848PDA/848PDAP/848PDAG MOTHERBOARD
1-1 FEATURE OF MOTHERBOARD............................................................................ 1
1-2 SPECIFICATION................................................................................................. 2
1-3 PERFORMANCE LIST.......................................................................................... 3
1-4 LAYOUT DIAGRAM & JUMPER SETTING............................................................ 4
CHAPTER 2 HARDWARE INSTALLATION
2-1 HARDWARE INSTALLATION STEPS..................................................................... 6
2-2 CHECKING MOTHERBOARD'S JUMPER SETTING.............................................. 6
2-3 INSTALL CPU ..................................................................................................... 7
2-3-1 GLOSSARY ............................................................................................ 7
2-3-2 ABOUT INTEL PENTIUM 4 478-PIN CPU ................................................. 8
2-4 INSTALL MEMORY ............................................................................................. 8
2-5 EXPANSION CARD ........................................................................................... 9
2-5-1 PROCEDURE FOR EXPANSION CARD INSTALLATION .......................... 9
2-5-2 ASSIGNING IRQ FOR EXPANSION CARD ............................................ 10
2-5-3 INTERRUPT REQUEST TABLE FOR THIS MOTHERBOARD ......................... 10
2-5-4 AGP SLOT.............................................................................................. 11
2-6 CONNECTORS, HEADERS ................................................................................. 11
2-6-1 CONNECTORS ...................................................................................... 11
2-6-2 HEADERS ............................................................................................... 14
2-7 STARTING UP YOUR COMPUTER ....................................................................... 18
CHAPTER 3 INTRODUCING BIOS
3-1 ENTERING SETUP ............................................................................................... 19
3-2 GETTING HELP ................................................................................................... 19
3-3 THE MAIN MENU ............................................................................................... 20
3-4 STANDARD CMOS FEATURES............................................................................ 21
3-5 ADVANCED BIOS FEATURES............................................................................. 22
3-6 ADVANCED CHIPSET FEATURES ....................................................................... 24
3-6-1 DRAM TIMING SETTINGS ...................................................................... 25
3-7 INTEGRATED PERIPHERALS................................................................................ 26
3-7-1 ONBOARD IDE FUNCTION.................................................................... 26
3-7-2 ONBOARD DEVICE FUNCTION ............................................................ 27
3-7-3 ONBOARD SUPER IO FUNCTION.......................................................... 28
3-8 POWER MANAGEMENT SETUP .......................................................................... 29
3-8-1 PM TIMER RELOAD EVENTS.................................................................. 30
3-9 PNP/PCI CONFIGURATION SETUP.................................................................... 31
3-9-1 IRQ RESOURCES................................................................................... 32
3-10 PC HEALTH STATUS .......................................................................................... 32
3-11 MISCELLANEOUS CONTROL............................................................................ 33
3-12 LOAD STANDARD/OPTIMIZED DEFAULTS ........................................................ 34
3-13 SET SUPERVISOR/USER PASSWORD................................................................. 34
CHAPTER 4 DRIVER & FREE PROGRAM INSTALLATION
MAGIC INSTALL SUPPORTS WINDOWS 98SE/ME/NT4.0/2000/XP............................ 35
4-1 INF INSTALL INTEL 848 CHIPSET SYSTEM DRIVER............................... 36
4-2 SOUND INSTALL ALC AC97’ CODEC AUDIO DRIVER.............................. 37
4-3 LAN INSTALL REALTEK LAN CONTROLLER DRIVER.............................. 38
4-4 USB2.0 INSTALL INTEL USB2.0 DRIVER ..................................................... 38
4-5 PC-HEALTH INSTALL SMART GUARDIAN SOFTWARE FOR HARDWARE
4-5-1 HOW TO UTILIZE PC-HEALTH................................................................ 40
4-6 MBIOS&DX9 INSTALL BIOS LIVE UPDATE UTILITY AND DIRECTX9.............. 40
4-7 PC-CILLIN INSTALL PC-CILLIN2002 ANTI-VIRUS PROGRAM.................. 42
4-8 HOW TO UPDATE BIOS...................................................................................... 44
TABLE OF CONTENT
MONITORING DEVICE ................................................................ 39
i
USER’S NOTICE
COPYRIGHT OF THIS MANUAL BELONGS TO THE MANUFACTURER. NO PART OF THIS MANUAL,
INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE REPRODUCED,
TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR BY ANY MEANS
WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER.
THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE 848PDA/848PDAP/848PDAG
MOTHER-BOARD AND WE DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT WILL
CHANGE, CORRECT ANY TIME WITHOUT NOTICE. MANUFACTURER PROVIDES THIS MANUAL “AS
IS” WITHOUT WARRANTY OF ANY KIND, AND WILL NOT BE LIABLE FOR ANY INDIRECT,
SPECIAL, INCIDENTIAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMANGES FOR LOSS OF
PROFIT, LOSS OF BUSINESS, LOSS OF USE OF DATA, INTERRUPTION OF BUSINESS AND THE
LIKE).
PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE
REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES, AND THEY
ARE USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER’S BENEFIT,
WITHOUT INTENT TO INFRINGE.
Manual Revision Information
Reversion Revision History Date
1.0 First Release Oct. 2003
Item Checklist
5
848PDA/848PDAP/848PDAG Motherboard
5
Cable for IDE/Floppy
5
CD for motherboard utilities
□
Cable for USB2 Port (Option)
5
848PDA/848PDAP/848PDAG User’s Manual
Intel Pentium 4 Processor Family
Cooling Solutions
As processor technology pushes to faster speeds and higher performance, thermal management
becomes increasingly crucial when building computer systems. Maintaining the proper thermal
environment is key to reliable, long-term system operation. The overall goal in providing the proper
thermal environment is keeping the processor below its specified maximum case temperature.
Heatsinks induce improved processor heat dissipation through increased surface area and
concentrated airflow from attached fans. In addition, interface materials allow effective transfers of
heat from the processor to the heatsink. For optimum heat transfer, Intel recommends the use of
thermal grease and mounting clips to attach the heatsink to the processor.
When selecting a thermal solution for your system, please refer to the website below for collection of
heatsinks evaluated and recommended by Intel for use with Intel processors. Note, those heatsinks are
recommended for maintaining the specified Maximum T case requirement. In addition, this collection
is not intended to be a comprehensive listing of all heatsinks that support Intel processors.
For vendor list of heatsink and fan, please visit :
http://developer.intel.com/design/Pentium4/components/index
ii
Chapter 1
Introduction of 848PDA/848PDAP/848PDAG Motherboard
1-1 Feature of motherboard
The 848PDA/848PDAP/848PDAG motherboard is design for use Intel Pentium 4 Processor
in 478 Pin Package/Northwood/Hyper Threading Processor with the Intel 848P Chipset
delivers a high performance and professional desktop platform solution. Which utilize the
Socket 478 design and the memory size expandable to 2.0GB.
These motherboards use the newest Intel 848P Chipset Supports 800/533/400MHz System
Bus in data transfer rate, these motherboards provided 200/166/133MHz SDRAM clock
frequency support DDR400/DDR333/DDR266 SDRAM. The motherboard embedded ICH4
chipset offers two parallel ULTRA ATA 100 interface to provide speedier HDD throughout
that boosts overall system performance.
For those wanting even greater graphic performance, an AGP slot is included on the board
(For 1.5V AGP card only. No for 3.3V or Universal AGP card). This AGP slot will
support either a 4X/8X VGA card.
The 848PDAP motherboard including Fast Ethernet PCI controller chip support 10Mb/s,
100Mb/s Base transfer rate. The 848PDAG motherboard including Fast Giga LAN PCI
controller chip support 10Mb/s, 100Mb/s, 1000Mb/s Base transfer rate.
These motherboards also has an integrated 6-channel AC97’ CODEC chip on board support
6-channel 3D surround positioning Audio which is fully compatible with Sound Blaster Pro
that gives you the best sound quality and compatibility.
With USB control as well as capability of expanding to six USB2.0 function ports, these
motherboards meet future USB demand also these motherboards have built-in hardware
monitor function. This will monitor and protect your computer. These motherboards special
design in hardware to protect BIOS from virus crash BIOS data.
These motherboards provide special function in BIOS Setup to setting CPU Host clock step
by step increasing let users to approach over clocking.
These motherboards provided high performance & meet future specification demand. It is
really wise choice for your computer.
1
1-2 Specification
Spec Description
ATX form factor 4 layers PCB size: 30.5x19.0cm
Design
Chipset
CPU Socket
(mPGA478B Socket)
Memory Socket
Expansion Slot &
Headers
Integrate IDE
LAN On Board
(for 848PDAP/848PDAG)
Audio
BIOS
∗
Intel 848P Memory Controller Hub (MCH) Chipset
∗
Intel 82801DB I/O Controller Hub (ICH4) Chipset
∗
Support Intel Pentium 4 478 Pin package utilizes Flip-Chip Pin
∗
Grid Array (FC-PGA2) package processor
Support CPU Frequency 400MHz/533MHz/800MHz
∗
Support 1.6G∼3.2G 478 Pin Pentium 4 processor
∗
Reserves support for future Intel Pentium 4 processors
∗
184-pin DDR SDRAM module socket x2
∗
Support DDR266/DDR333/DDR400 DDR SDRAM
∗
Expandable to 2.0GB
∗
AGP slot x1 for AGP 0.8V/1.5V standard only, support AGP
∗
2.0/3.0 & 4X/8X mode
32-bit PCI slot x 5, CNR slot x 1
∗
Two IDE controllers support PCI Bus Mastering, ATA
∗
PIO/DMA and the ULTRA DMA 33/66/100 functions that
deliver the data transfer rate up to 100 MB/s
Realtek RT8100C PCI LAN controller chip for 848PDAP
∗
Supports 10/100 Mb/sec data transfer rate
Realtek RT8110S Giga LAN PCI controller chip for
∗
848PDAG Supports 10/100/1000 Mb/sec data transfer rate
Realtek ALC 6-channel AC97’ Codec integrated
∗
Support 6-channel 3D surround & Positioning Audio
∗
Audio driver and utility included
∗
Award 4Mb Flash ROM
∗
Multi I/O
PS/2 keyboard and PS/2 mouse connectors
∗
Floppy disk drive connector x1
∗
Parallel port x1, Serial port x2
∗
USB 2.0 connector x2, headers x4 (connecting cable option)
∗
Audio connector Line-in, Line-out, MIC & Game Port header
∗
2
1-3 Performance List
The following performance data list is the testing result of some popular benchmark testing
programs. These data are just referred by users, and there is no responsibility for different
testing data values gotten by users (the different Hardware & Software configuration will
result in different benchmark testing results.)
Performance Test Report
CPU:
DRAM:
On Board VGA:
Hard Disk Driver:
BIOS:
OS:
Intel Pentium 4 2.53GHz (533MHz FSB)/3GHZ (800MHz FSB) mPGAB package
512MB DDR400 SDRAM x2 (KINGSTON D328DW)
1024x768x32bit Color
IBM IC35L040AVVN07-0 (ATA-100 7200RPM)
Award Optimal default
Win XP Professional (Service Pack 1)
2.53GHz
133/133
3GHz
200/200
3D Mark 2001SE 2192 2506
3D Mark 2003 59 70
3D Winbench 2000 (32/32BIT) 73.2 78.3
PC Mark 2002
CPU/Memory/HDD 6146/5410/879 7336/6480/879
Content Creation Winstone 2002 41 48.9
Content Creation Winstone 2003 41.9 49.6
Business Winstone 2002 29.4 33.3
Winbench 99 V1.2:
Business Disk Winmark99 8600 8840
Hi-end Disk Winmark99 32200 31700
Business Graphic Winmark 164 205
Hi-end Graphic Winmark 591 852
SYS Mark 2001/2002 : SISMark 2001/2002 Rating (Internet Content
Creation / Office Productivity)
SISMark 2001 236 (263/212) 278 (314/247)
SISMark 2002 in Windows XP 245 (346/173) 283 (411/195)
SISOFT Sandra 2003 :
Dhrystone ALU MIPS 6778 7712
Whetstone FPU iSSE2 MFLOPS 1407/3114 1711/3944
RAM Int Buffered iSSE2 MB/S 2204 2688
RAM Float Buffered iSSE2 MB/S 2204 2689
Integer SSE2 IT/S 10033 11923
Floating-Point SSE2 IT/S 12768 15177
QUAKE3 DEMO1 FPS 110.9 125.6
DEMO2 FPS 110.5 127.3
Return to Castle Wolfenstein FPS 74.4 84.5
WCPUID System / CPU Clock 132.98/2526.62 199.66/2995.70
3
/
1-4 Layout Diagram & Jumper Setting
GAME/MIDI PORT
MIC
LINE-IN
LINE-OUT
CPU FAN
CPU Socket
PS/2 Mouse
PS/2 Keyboard
ATX 12V Power Connector
K/B Power ON Jumper
PS2 KB/Mouse Port
LAN Connector
(JP1)
USB Port
PRINTLAN
COM1 COM2 USB
PC99 Back Panel
CD Audio
ATX Power Connector
SYSFAN2
RTL8100C LAN Chip
Front Panel Audio
6-CH AC’97 Audio Codec
PCI Slot
ITE 8712 I/O Chip
IR Connector
4MBit FWH BIOS
SYSFAN1
Wake On LAN
DDR DIMMx2
ATA 100 IDE Connector
Intel 848P Chip
AGP 4X/8X 1.5V Slot
Intel 82801DB Chip
Clear CMOS (JP2)
Floppy Connector
Power LED, Speak Connector
Front Panel Connector
USB Port
(USB2, USB3)
4
Jumpers
Jumper Name Description Page
JP2 CMOS RAM Clear 3-pin Block P.6
JP1 Keyboard Power On Enable/Disabled 3-pin Block P.7
Connectors
Connector Name Description Page
ATXPWR ATX Power Connector 20-pin Block P.11
ATX12V ATX 12V Power Connector 4-pin Block P.12
USB USB Port Connector 4-pin Connector P.12
LAN
(for 848PDAP/848PDAG)
KB&MOUSE
(PS2 KB/MOUSE)
PARALLEL Parallel Port Connector 25-pin Female P.12
AUDIO_GAME Audio Line In/Out MIC Connector
COM1, COM2 Serial Port COM1/COM2
FDD Floppy Driver Connector 34-pin Block P.13
IDE1/IDE2 Primary/Secondary IDE Connector 40-pin Block P.13
LAN Connectors RJ-45 Connector P.12
PS/2 Mouse & PS/2 Keyboard
6-pin Female P.12
Connector
GAME Connector
3 phone jack Connector
15-pin D-Sub Connector
P.12
9-pin Connector P.13
Connector
Headers
Header Name Description Page
AUDIO Line-Out, MIC Headers 9-pin Block P.14
USB2, USB3 USB Port Headers 9-pin Block P.14
SPEAK Speaker connector 4-pin Block P.15
JW_FP
(Power LED/Reset/
IDE LED/ Power Button)
Front Panel Header
(including Power LED/ IDE activity LED/
Reset switch / Power On Button lead)
9-pin Block P.15
WOL Wake On-LAN Headers 3-pin Block P.15
SYSFAN1, SYSFAN2,
FAN Speed Headers 3-pin Block P.16
CPUFAN
IR IR infrared module Headers 5-pin Block P.16
CDIN CD Audio-In Headers 4-pin Block P.17
Expansion Sockets
Socket/Slot Name Description Page
ZIF Socket 478 CPU Socket 478-pin mPGAB CPU Socket P.8
DIMM1, DIMM2 DDR Module Socket 184-pin DDR SDRAM Module
Expansion Socket
PCI1 ∼ PCI5 PCI Slot 32-bit PCI Local Bus Expansion slots P.9
AGP AGP 4X/8X Mode Slot AGP Expansion Slot P.11
P.8
5
Chapter 2
Hardware installation
2-1 Hardware installation Steps
Before using your computer, you had better complete the following steps:
1. Check motherboard jumper setting
2. Install CPU and Fan
3. Install System Memory (DIMM)
4. Install Expansion cards
5. Connect IDE and Floppy cables, Front Panel /Back Panel cable
6. Connect ATX Power cable
7. Power-On and Load Standard Default
8. Reboot
9. Install Operating System
10. Install Driver and Utility
2-2 Checking Motherboard’s Jumper Setting
(1) CMOS RAM Clear (3-pin) : JP2
A battery must be used to retain the motherboard configuration in CMOS RAM short 1-2
pins of JP2 to store the CMOS data.
To clear the CMOS, follow the procedure below:
1. Turn off the system and unplug the AC power
2. Remove ATX power cable from ATX power connector
3. Locate JP2 and short pins 2-3 for a few seconds
4. Return JP2 to its normal setting by shorting pins 1-2
5. Connect ATX power cable back to ATX power connector
Note: When should clear CMOS
1. Troubleshooting
2. Forget password
3. After over clocking system boot fail
13
JP2
1-2 closed Normal (Default)
CMOS RAM Clear Setting
1 3
JP2
2-3 closed Clear CMOS
6
(2) Keyboard Power On function Enabled/Disabled: JP1
When setting Enabled you can using keyboard by key in password device to power on
system.
JP1
JP1
JP1 1-2 closed K/B Power ON Disabled (Default)
1
3
1
JP1 2-3 closed K/B Power ON Enabled
3
2-3 Install CPU
2-3-1 Glossary
Chipset (or core logic) - two or more integrated circuits which control the interfaces between the
system processor, RAM, I/O devises, and adapter cards.
Processor slot/socket - the slot or socket used to mount the system processor on the motherboard.
Slot (AGP, PCI, ISA, RAM) - the slots used to mount adapter cards and system RAM.
AGP - Accelerated Graphics Port - a high speed interface for video cards; runs at 1X (66MHz),
2X (133MHz), or 4X (266MHz).
PCI - Peripheral Component Interconnect - a high speed interface for video cards, sound cards,
network interface cards, and modems; runs at 33MHz.
ISA - Industry Standard Architecture - a relatively low speed interface primarily used for sound
cards and modems; runs at approx. 8MHz.
Serial Port - a low speed interface typically used for mouse and external modems.
Parallel Port - a low speed interface typically used for printers.
PS/2 - a low speed interface used for mouse and keyboards.
USB - Universal Serial Bus - a medium speed interface typically used for mouse, keyboards,
scanners, and some digital cameras.
Sound (interface) - the interface between the sound card or integrated sound connectors and
speakers, MIC, game controllers, and MIDI sound devices.
LAN (interface) - Local Area Network - the interface to your local area network.
BIOS (Basic Input/Output System) - the program logic used to boot up a computer and establish
the relationship between the various components.
Driver - software, which defines the characteristics of a device for use by another device or other
software.
Processor - the "central processing unit" (CPU); the principal integrated circuit used for doing
the "computing" in "personal computer"
Front Side Bus Frequency -
the clock generator for CPU, DRAM and PCI BUS.
CPU L2 Cache -
the flash memory inside the CPU, normally Athlon CPU has 256K or above,
while Duron will have 64K.
the working frequency of the motherboard, which is generated by
2-3-2 About Intel Pentium 4 478-pin CPU
7
This motherboard provides a 478-pin surface mount, Zero Insertion Force (ZIF) socket,
referred to as the mPGA478B socket supports Intel Pentium 4 processor in the 478 Pin
package utilizes Flip-Chip Pin Grid Array (FC-PGA2) package technology.
The CPU that comes with the motherboard should have a cooling FAN attached to prevent
overheating. If this is not the case, then purchase a correct cooling FAN before you turn on
your system.
WARNING!
Be sure that there is sufficient air circulation across the processor’s heatsink and
CPU cooling FAN is working correctly, otherwise it may cause the processor and
motherboard overheat and damage, you may install an auxiliary cooling FAN, if
necessary.
To install a CPU, first turn off your system and remove its cover. Locate the ZIF socket and
open it by first pulling the level sideways away from the socket then upward to a 90-degree
angle. Insert the CPU with the correct orientation as shown below. The notched corner
should point toward the end of the level. Because the CPU has a corner pin for two of the
four corners, the CPU will only fit in the orientation as shown.
mPGA478B
CPU ZIF mPGAB Socket
Colden Arrow
When you put the CPU into the ZIF socket. No force require to insert of the CPU, then press
the level to Locate position slightly without any extra force.
2-4 Install Memory
This motherboard provides two 184-pin DUAL INLINE MEMORY MODULES (DIMM)
sites for memory expansion available from minimum memory size of 64MB to maximum
memory size of 2.0GB DDR SDRAM.
Valid Memory Configurations
Bank 184-Pin DIMM PCS Total Memory
Bank 0, 1 (DIMM1) DDRDDR266/DDR333/DDR400
DDR SDRAM Module
Bank 2, 3 (DIMM2) DDRDDR266/DDR333/DDR400
DDR SDRAM Module
8
X1
X1
64MB∼1.0GB
64MB∼1.0GB
Generally, installing DDR SDRAM modules to your motherboard is very easy, you can refer
to figure 2-4 to see what a 184-Pin DDR266/DDR333/DDR400 DDR SDRAM module looks
like.
DI MM2 (BANK2 + BANK3)
DI MM1 (BANK0 + BANK1)
Figure 2-4
NOTE!
WARNING!
When you install DIMM module fully into the DIMM socket the eject tab should be
locked into the DIMM module very firmly and fit into its indention on both sides.
For the DDR SDRAM CLOCK is set at 200MHz, use only DDR400-compliant DDR
Modules. When this motherboard operate at 200Mhz, most system will not even
boot if non-compliant modules are used because of the strict timing issues, if your
SDR Modules are not DDR400-compliant, set the DDR SDRAM clock to 133MHz
to ensure system stability.
2-5 Expansion Cards
WARNING!
2-5-1 Procedure For Expansion Card Installation
1. Read the documentation for your expansion card and make any necessary hardware or
software setting for your expansion card such as jumpers.
2. Remove your computer’s cover and the bracket plate on the slot you intend to use.
3. Align the card’s connectors and press firmly.
4. Secure the card on the slot with the screen you remove above.
5. Replace the computer system’s cover.
6. Set up the BIOS if necessary.
7. Install the necessary software driver for your expansion card.
Turn off your power when adding or removing expansion cards or other system
components. Failure to do so may cause severe damage to both your motherboard
and expansion cards.
2-5-2 Assigning IRQs For Expansion Card
9
Some expansion cards need an IRQ to operate. Generally, an IRQ must exclusively assign to
one use. In a standard design, there are 16 IRQs available but most of them are already in use.
Standard Interrupt Assignments
IRQ Priority Standard function
0 N/A System Timer
1 N/A Keyboard Controller
2 N/A Programmable Interrupt
3 * 8 Communications Port (COM2)
4 * 9 Communications Port (COM1)
5 * 6 Sound Card (sometimes LPT2)
6 * 11 Floppy Disk Controller
7 * 7 Printer Port (LPT1)
8 N/A System CMOS/Real Time Clock
9 * 10 ACPI Mode when enabled
10 * 3 IRQ Holder for PCI Steering
11 * 2 IRQ Holder for PCI Steering
12 * 4 PS/2 Compatible Mouse Port
13 N/A Numeric Data Processor
14 * 5 Primary IDE Channel
15 * 1 Secondary IDE Channel
* These IRQs are usually available for ISA or PCI devices.
2-5-3 Interrupt Request Table For This Motherboard
Interrupt request are shared as shown the table below:
INT A INT B INT C INT D INT E INT F INT G INT H
Slot 1
Slot 2
Slot 3
Slot 4
Slot 5
Onboard LAN
Onboard USB 1
Onboard USB 2
Onboard USB 3
Sound
IMPORTANT!
√
If using PCI cards on shared slots, make sure that the drivers support “Shared
IRQ” or that the cards don’t need IRQ assignments. Conflicts will arise between
the two PCI groups that will make the system unstable or cards inoperable.
√
√
√
√
√
√
√
√
√
2-5-4 AGP Slot
This motherboard provides an AGP Slot, only support the 1.5V 4X/0.8V 8X AGP VGA card.
10
Do not use AGP 2X card (3.3V) in this motherboard. It will burn and damage the
motherboard due to Intel® 848 chipset can not support AGP 2X (3.3V).
IMPORTANT!
Example 1:
SiS 305 & ATi Rage 128 Pro AGP card those golden finger is compatible
Before you plug-in AGP card, please make sure the following notice is
fully understood and practiced. If your AGP card has “AGP 4X notch
(show below) please make sure your AGP card is AGP 4X/8X
(1.5V/0.8V) not AGP 2X (3.3V)
2x notch 4x notch
AGP SLOT
with 2X/4X mode AGP slot, but only can support 2X (3.3V) only. If you
install these cards in Intel® 848 based motherboard it will burn and damage
the motherboard.
Example 2:
We also find Diamond Vipper V770 golden finger is design for 2X/4X mode
AGP Slot. It can be adjusted the jumper for AGP 2X (3.3V) or AGP 4X
(1.5V). But the factory default setting is 2X (3.3V). If you install this AGP
card in motherboard without change the jumper setting to 4X (1.5V), it will
burn the motherboard.
2-6 Connectors, Headers
2-6-1 Connectors
(1) Power Connector (20-pin block) : ATXPWR
ATX Power Supply connector. This is a new defined 20-pins connector that usually comes
with ATX case. The ATX Power Supply allows to use soft power on momentary switch that
connect from the front panel switch to 2-pins Power On jumper pole on the motherboard.
When the power switch on the back of the ATX power supply turned on, the full power will not
come into the system board until the front panel switch is momentarily pressed. Press this
switch again will turn off the power to the system board.
11
PIN ROW2 ROW1
1 3.3V 3.3V
2 -12V 3.3V
3 GND GND
4 Soft Power On 5V
5 GND GND
6 GND 5V
7 GND GND
8 -5V Power OK
9 +5V +5V (for Soft Logic)
10 +5V +12V
Pin 1
(2) ATX 12V Power Connector (4-pin block) : ATX12V
This is a new defined 4-pins connector that usually comes with ATX Power Supply. The ATX
Power Supply which fully support Pentium 4 processor must including this connector for
support extra 12V voltage to maintain system power consumption. Without this connector
might cause system unstable because the power supply can not provide sufficient current for
system.
Pin 1
(3) USB Port connector: USB (USB)
The connectors are 4-pin connector that connect USB devices to the system board.
(4) LAN Port connector: LAN (for 848PDAP/848PDAG)
This connector is standard RJ45 connector for Network connector.
(5) PS/2 Mouse & PS/2 Keyboard Connector: KB&MOUSE (PS2 KB/MOUSE)
The connectors for PS/2 keyboard and PS/2 Mouse.
(6) Parallel Port Connector (25-pin female): PARALLEL
Parallel Port connector is a 25-pin D-Subminiature Receptacle connector. The On-board
Parallel Port can be disabled through the BIOS SETUP. Please refer to Chapter 3
“INTEGRATED PERIPHERALS SETUP” section for more detail information.
(7) Audio Line-In, Lin-Out, MIC Connector : AUDIO_GAME
This Connector are 3 phone Jack for LINE-OUT, LINE-IN, MIC and 15-pin D-Subminiature
female connector for GAME/MIDI port.
Line-out :
Line-in :
Audio input to sound chip
MIC :
GAME :
Audio output to speaker
Microphone Connector
GAME/MIDI Port Connector
(8) Serial Port COM1/COM2: COM1/COM2
12
Loading...