4-9 HOW TO DISABLE ON-BOARD SOUND .........................................................................46
4-10 HOW TO UPDATE BIOS ..................................................................................................... 46
TABLE OF CONTENT
i
Page 3
USER’S NOTICE
COPYRIGHT OF THIS MANUAL BELONGS TO THEMANUFACTURER. NO PART OF THIS
MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT MAY BE
REPRODUCED, TRANSMITTED OR TRANSLATED INTO ANY LANGUAGE IN ANY FORM OR
BY ANY MEANS WITHOUT WRITTEN PERMISSION OF THE MANUFACTURER.
THIS MANUAL CONTAINS ALL INFORMATION REQUIRED TO USE THIS MOTHER-BOARD
AND WE DO ASSURE THIS MANUAL MEETS USER’S REQUIREMENT BUT WILL CHANGE,
CORRECT ANY TIME WITHOUT NOTICE. MANUFACTURER PROVIDES THIS MANUAL “AS IS”
WITHOUT WARRANTY OF ANY KIND, AND WILL NOT BE LIABLE FOR ANY INDIRECT,
SPEC I A L, INCIDENTIAL OR CONSEQUENTIAL DAMAGES (IN C L UDI N G DAM A NGE S F OR L O S S O F
PROFIT, LOSS OF BUSINESS, LOSS OF USE OF DATA, INTERRUPTION OF BUSINESS AND THE
LIKE).
PRODUCTS AND CORPORATE NAMES APPEARING IN THIS MANUAL MAY OR MAY NOT BE
REGISTERED TRADEMARKS OR COPYRIGHTS OF THEIR RESPECTIVE COMPANIES, AND
THEY ARE USED ONLY FOR IDENTIFICATION OR EXPLANATION AND TO THE OWNER’S
BENEFIT, WITHOUT INTENT TO INFRINGE
Manual Revision Information
Reversion Revision History Date
1.0 First Release July 2002
Item Checklist
5
Motherboard
5
Cable for IDE/Floppy
5
CD for motherboard utilities
□
Cable for USB Port 3/4 (Option)
5
Cable for COM2 (Option)
5
User’s Manual
Intel Processor Family
Thermal Solutions
As processor technology pushes to faster speeds and higher performance, thermal management
becomes increasingly crucial when building computer systems. Maintaining the proper thermal
environment is key to reliable, long-term system operation. The overall goal in providing the proper
thermal environment is keeping the processor below its specified maximum case temperature.
Heatsinks induce improved processor heat dissipation through increased surface area and
concentrated airflow from attached fans. In addition, interface materials allow effective transfers of
heat from the processor to the heatsink. For optimum heat transfer, Intel recommends the use of
thermal grease and mounting clips to attach the heatsink to the processor.
When selecting a thermal solution for your system, please refer to the website below for collection of
heatsinks evaluated and recommended by Intel for use with Intel processors.
Vendor list for heatsink and fan of Pentium® III processor, please visit:
http://developer.intel.com/design/Pentiumiii/components/index.htm
Vendor list for heatsink and fan of Intel® Celeron™ processor, please visit:
Introduction of 815EDA/815EDAL/815EPDA/815EPDAL
Motherboard
1-1 Feature of motherboard
The motherboard is design for use Intel’s new generation Pentium III /Tualatin processors,
which utilize the Socket 370 design and the memory size expandable to 512MB.
This motherboard use the newest Intel chipset, whose 133MHz front side bus & 133MHz
memory interface delivers a clear upgrade path to the future generation of 133MHz processors
and PC-133 SDRAM. It offers ULTRA DMA 100MB/sec (ATA 100) to provide speedier
HDD throughout that boosts overall system performance.
815EDA/815EDAL with integrated 3D Graphic Accelerator, makes this board lower cost
alternative to a video card. For those wanting even greater graphic performance, an AGP 4X
slot is included on the board. This AGP slot will support either a 1X, 2X, 4X AGP VGA card.
The 815EDAL/815EPDAL integrated PCI LAN controller supports IEE802.3 standard
provide 10/100 Mb/s data transfer rate for network.
The motherboard integrated AC’97 2.1 CODEC on board which is fully compatible with
Sound Blaster Pro that gives you the best sound quality and compatibility. With 2 USB
control as well as capability of expanding to 4 USB connectors, which guarantees this board
to meet future USB demand. Moreover, these motherboards have built-in hardware monitor
function that capable of monitor and protect your computer.
The motherboard also provides special function in BIOS Setup to setting CPU Host clock step
by step increasing let users to approach over clocking
.
This motherboard provides high performance & meets future specification demand. It is
really wise choice for your computer.
1-2 Specification
2
Page 5
Spec Description
ATX form factor 4 layers PCB size: 30.5x17.0cm
Design
Chipset
CPU Socket
Memory Socket
Expansion Slot & Headers
LAN On Board
(Only for
815EDAL/815EPDAL)
Integrate VGA
(Only for
815EDA/815EDAL)
Integrate IDE
AC’97Audio
∗
BIOS
Multi I/O
∗
Intel 815E B-Step Graphic Memory Controller Hub
∗
(GMCH) Chipset
Intel 815EP B-Step Memory Controller Hub (MCH)
∗
Chipset
Intel 82801BA I/O Controller Hub (ICH) chipset
∗
Support Pentium III 500∼1.2GHz processor
∗
Support Celeron™ 500~1.4GHz processor
∗
Support 66, 100 and 133MHz CPU Bus clock
∗
Reserves support for future Intel Pentium III processors
∗
168-pin DIMM socket x2 Expandable to 512MB
∗
Support 3.3V PC-100/PC-133 SDRAM Module
∗
AGP slot x1 support AGP 2.0 & 4X mode
∗
32-bit PCI slot x5
∗
CNR slot x1
∗
VIA PCI LAN Controller chip
∗
Support 10/100 Mb/s data transfer rate compliant IEE
∗
for 815EPDA/815EPDAL
for 815EDA/815EDAL
802.3 standard
3D graphic acceleration
∗
Intel GMCH Built-in Graphics supports up to
∗
1280x1024x24 bits 85Hz
2 channel of Bus Master IDE port supporting ULTRA
∗
DMA 33/66/100 mode devices
AC’97 Digital Audio controller integrated
AC’97 Audio CODEC on board
∗
Audio driver and utility included
∗
Award 2Mb Flash ROM
∗
PS/2 keyboard and PS/2 mouse connectors
∗
Floppy disk drive connector x1
∗
Parallel port x1, Serial Port x2
∗
USB connector x2 and USB headers x2 (connecting
∗
cable option)
Audio connector (Line-in, Line-out, MIC & Game Port)
∗
1-3 Performance List
3
Page 6
The following performance data list is the testing result of some popular benchmark testing
programs. These data are just referred by users, and there is no responsibility for different
testing data values gotten by users (the different Hardware & Software configuration will
result in different benchmark testing results.)
CPU:
DRAM:
VGA Expansion Card:
Hard Disk Driver:
BIOS:
3D Mark 99 1417 5934
3D Mark 2000 957 4229
3D Winbench 99 V1.2 327 898
3D Winbench 2000 17.4 82.5
Final Reality 6.15 6.16
Winstone 99 V1.3 31.8 33.4
Winstone 2000 34.5 34.8
Winbench 99 :
CPU Mark 99 76.7 78.6
FPU Winmark 99 4620 4610
Business Disk Winmark99 5190 5210
Hi-end Disk Winmark99 17800 17900
Business Graphic Winmark 219 399
Hi-end Graphic Winmark 776 1100
SYS Mark 2000 : SISMark 2000 Rating ( Internet Content Creation / Office
Productivity )
Suites 173 (173/173) 182 (179/185)
Official 173 (176/170) 184 (186/181)
SISOFT Sandra 2000 :
CPU MIPS 2360 2358
FPU MFLOPS 1169 1168
CPU / Memory MB/S 290 326
FPU / Memory MB/S 297 339
QUAKE3 :
DEMO1 FPS 30.8 108.5
DEMO2 FPS 31.1 102.8
1-4 Layout Diagram & Jumper Setting
4
Page 7
(for 815EDAL/815EPDAL)
LAN
PRINT GAME/MIDI PORT
PS/2 Mouse
PS/2 Keyboard
USB
K/B Power ON Jumper
PS2 KB/Mouse Port
/LAN Connector
(for 815EDAL/
815EPDAL)
(JK1)
USB Port
COM1 VGA
(Only for
815EDA/815EDAL)
MIC
LINE-IN
LINE-OUT
370 CPU Socket
FAN1
DIMM Socket X2
PC99 Back Panel
COM2 Connector
CD Audio
FAN2
Winbond W83627HF Chip
PCI Slot
Wake On LAN
IR Connector
CNR Slot
FAN3
Jumpers
Jumper Name Description Page
CPU F.S.B. Clock Select
Jumper (JS1, JS2, JS3, JS4)
ATX Power Connector
ATA 100 IDE Connector
Intel 815E/815EP Chip
AGP Slot
(JBAT)
Clear CMOS Jumper
Intel 82801BA Chip
Floppy Connector
Speaker Connector
Front Panel Connector
2MBit Flash ROM BIOS
USB Port (USB1)
5
Page 8
JS3, JS4
JS1, JS2
CPU & SDRAM Frequency Setting 3-pin Block
2-pin Block
p.7
JK1 Keyboard Power ON Function Setting 3-pin Block p.8
JBAT CMOS RAM Clear 3-pin Block p.8
Connectors
Connector Name Description Page
ATXPWR ATX Power Connector 20-pin Block p.15
CN1
(PS2 KB/MS)
UL_B USB Port Connector 4-pin Connector p.15
LAN LAN Port Connector RJ-45 Connector p.15
VGA VGA Port Connector 15-pin Female D-Sub connector p.15
LPT Parallel Port Connector 25-pin Female p.15
GAME Audio/Game Connector 3 phone jack+15-pin Connector p.15
COM1 Serial Port COM1 Connector 9-pin Connector p.15
FDC Floppy Driver Connector 34-pin Block p.16
IDE1/IDE2 Primary/Secondary IDE Connector 40-pin Block p.16
For 815EDAL/825EPDAL only
PS/2 Mouse & PS/2 Keyboard
Connector
6-pin Female p.15
For 815EDA/815EDAL only
Headers
Header Name Description Page
COM2 Serial Port COM2 Header 9-pin Block P.17
USB1 USB Port Headers 9-pin Block p.17
FP
(Power LED/Reset/
IDE LED/Power
Button)
SPEAK Speaker connector 4-pin Block p.17
WOL Wake On-LAN Headers 3-pin Block p.18
FAN1, FAN2, FAN3 FAN Speed Headers 3-pin Block p.18
IR IR infrared module Headers 5-pin Block p.19
CDIN CD Audio-In Headers 4-pin Block p.19
Expansion Sockets
Socket/Slot Name Description Page
ZIF Socket 370 CPU Socket 370-pin FC-PGA CPU Socket p.10
DIMM1, DIMM2 DIMM Module Socket 168-pin DIMM SDRAM Module
9-pin Block P.17
(including Power LED/IDE activity
LED/Reset switch/Power On Button
lead)
p.12
Expansion Socket
PCI Slot 32-bit PCI Local Bus Expansion slots p.13
Chapter 2
Hardware installation
6
Page 9
2-1 Hardware installation Steps
Before using your computer, you had better complete the following steps:
1. Check motherboard setting
2. Install CPU
3. Install Memory
4. Install Expansion cards
5. Connect Ribbon cables, Panel wires, and power supply
6. Setup BIOS
7. Install software driver & utility
2-2 Checking Motherboard’s Jumper Setting
(1) CPU Host/SDRAM Clock setting: JS1, JS2, JS3, JS4
The motherboard’s CPU & SDRAM memory clock adjusted through jumper JS1, JS2,
JS3 & JS4. Table as below:
CPU/SDRAM (MHz) JS1 JS2 JS3 JS4
* AUTO ON ON 1-2 1-2
66/100
(Default)
OFF OFF 2-3 2-3
100/100 OFF OFF 1-2 2-3
133/100 OFF OFF 1-2 1-2
133/133 OFF OFF 2-3 1-2
1
2
1
2
∗
When jumper setting Auto it only can support CPU/SDRAM frequency at 66/100,
JS3
JS2
JS1
AUTO
JS2
JS1
133/100
JS4
1
1
2
3
JS3
JS4
1
1
2
3
JS2
JS1
66/100
(Default)
JS2
JS1
133/133
JS3
JS4
1
3
JS3
JS4
1
3
CPU Host/SDRAM Clock Setting
1
2
JS2
JS1
100/100
JS3
JS4
1
3
100/100, 133/100 MHz, we recommend setting 133/133 manually when use F.S.B.
133MHz CPU to increase performance.
In “Miscellaneous Control” section of CMOS Setup Utility, you can increase the CPU
clock step by step increase for over clocking possibility. Please refer to page 11 for more
details.
(2) Keyboard Power On Function setting (3-pin) : JK1
This allows you to disable the keyboard power on function. Set the jumper to enabled or
disabled if you wish to use your keyboard (by pressing < >) to power on your computer,
7
Page 10
this feature requires an ATX power supply that can supply at least 300mA on the +5VSB
lead. The default is set on disable.
JK1
1-2 closed : Disabled (default)
1
3
Keyboard Power On Function
JK1
2-3 closed : Enabled
1
3
(3) CMOS RAM Clear (3-pin) : JBAT
A battery must be used to retain the motherboard configuration in CMOS RAM short 1-2
pins of JBAT to store the CMOS data.
To clear the CMOS, follow the procedure below:
1. Turn off the system and unplug the AC power
2. Remove ATX power cable from ATX power connector
3. Locate JBAT and short pins 2-3 for a few seconds
4. Return JBAT to its normal setting by shorting pins 1-2
5. Connect ATX power cable back to ATX power connector
Note: When should clear CMOS
1. Troubleshooting
2. Forget password
3. After over clocking system boot fail
2-3 Install CPU
2-3-1 Glossary
JBAT
1-2 closed : Normal (default)
1
3
CMOS RAM Clear Setting
8
JBAT
2-3 closed :
1
3
Clear CMOS
Page 11
Chipset (core logic) - two or more integrated circuits which control the interfaces between the
system processor, RAM, I/O devises, and adapter cards.
Processor socket - the socket used to mount the system processor on the motherboard.
Slot (AGP, PCI, ISA, RAM) - the slots used to mount adapter cards and system RAM.
AGP - Accelerated Graphics Port - a high speed interface for video cards; runs at 1X
(66MHz), 2X (133MHz), or 4X (266MHz).
PCI - Peripheral Component Interconnect - a high speed interface for video cards, sound
cards, network interface cards, and modems; runs at 33MHz.
Serial Port - a low speed interface typically used for mouse and external modems.
Parallel Port - a low speed interface typically used for printers.
PS/2 - a low speed interface used for mouse and keyboards.
USB - Universal Serial Bus - a medium speed interface typically used for mouse, keyboards,
scanners, and some digital cameras.
Sound (interface) - the interface between the sound card or integrated sound connectors and
speakers, MIC, game controllers, and MIDI sound devices.
LAN (interface) - Local Area Network - the interface to your local area network.
BIOS (Basic Input/Output System) - the program logic used to boot up a computer and
establish the relationship between the various components.
Driver - software, which defines the characteristics of a device for use by another device or
other software.
Processor - the "Central Processing Unit" (CPU); the principal integrated circuit used for
doing the "computing" in "personal computer"
Front Side Bus Frequency
- The working frequency of the motherboard, which is generated
by the clock generator for CPU, DRAM and PCI BUS.
CPU L2 Cache
- The flash memory inside the CPU, normally Pentium III CPU has 256K or
above, while Celeron CPU will have 128K.
The way to recognize the specification of CPU from the packing Pentium III 370 pins
FC-PGA
On the surface of the CPU as shown on the right picture, under the word of “PENTIUM III”
the code is:
RB 80526 P2 866 256
RB :
P2 :
FC–PGA packing
P2–133MHz front side bus frequency
PY–100MHz front side bus frequency
866 :
CPU internal frequency, where here is
866MHz
256 :
the size of L2 cache, where here is 256K
Celeron FC–PGA
9
Page 12
On the surface of the CPU as shown on the right picture, under the word of “Celeron” the
code is:
566/128/66/1.5V
566 :
128 :
66 :
1.5V :
CPU internal frequency, where here is 566MHz
the size of L2 cache, where here is 128K
front side bus frequency, where here is 66MHz
the voltage for the CPU
2-3-2 Setting CPU Bus Clock & Memory Clock Jumper
Setting the front side bus frequency and SDRAM frequency
The motherboard uses jumper JS1, JS2, JS3 and JS4 for the front side bus frequency and
SDRAM frequency setting as shown from the table below:
CPU/SDRAM (MHz) JS1 JS2 JS3 JS4
AUTO ON ON 1-2 1-2
66/100
100/100 OFF OFF 1-2 2-3
133/100 OFF OFF 1-2 1-2
133/133 OFF OFF 2-3 1-2
(Default)
OFF OFF 2-3 2-3
Example: Using a Pentium III 866 CPU with front side bus frequency of 133MHz and
PC-133 SDRAM module, the setting of JS3 will be 2-3 and JS4 will be 1-2.
This sets both CPU BUS CLOCK and SDRAM CLOCK to be 133MHz.
For experience user looking for over clocking possibility, please refer to sec 2-3-4.
2-3-3 Install CPU
This motherboard provides a ZIF socket 370. The CPU that comes with the motherboard
should have a cooling FAN attached to prevent overheating. If this is not the case, then
purchase a correct cooling FAN before you turn on your system.
WARNING!
Be sure that there is sufficient air circulation across the processor’s
heatsink and CPU cooling FAN is working correctly, otherwise it may
cause the processor and motherboard overheat and damage, you may install
an auxiliary cooling FAN, if necessary.
To install a CPU, first turn off your system and remove its cover. Locate the ZIF socket and
open it by first pulling the level sideways away from the socket then upward to a 90-degree
angle. Insert the CPU with the correct orientation as shown below. The notched corner
should point toward the end of the level. Because the CPU has a corner pin for two of the
four corners, the CPU will only fit in the orientation as shown.
10
Page 13
Intel
Pentium
III
Socket 370
Colden Arrow
CPU ZIF Socket 370
When you put the CPU into the ZIF socket. No forces require to insert of the CPU, then press
the level to locate position slightly without any extra force.
2-3-4 Over clock Running
WARNING!
This section is for experienced motherboard installer only. Over clocking
can result in system instability or even shortening life of the processor.
After setting the Jumper JS1, JS2, JS3, JS4 you can choose over clock running by BIOS
CMOS SETUP UTILITY. When you entered CMOS SETUP UTILITY, choose
“Miscellaneous Control” you will see the screen as below then.
You can choose the situation you want to try.
CPU/SDRAM (MHz) JS1 JS2 JS3 JS4
AUTO ON ON 1-2 1-2
66/100
(Default)
OFF OFF 2-3 2-3
100/100 OFF OFF 1-2 2-3
133/100 OFF OFF 1-2 1-2
133/133 OFF OFF 2-3 1-2
CMOS Setup Utility – Copyright(C) 1984-2002 Award Software
Miscellaneous Control
CyrixIII Clock Ratio Default
Auto Detect DIMM/PCI Clk Enabled
Spread Spectrum Disabled
** Current Host Clock is 66Mhz **
CPU Host/SDRAM/PCI Clock 66/100/33Mhz
CPU Clock Ratio X 3
Flash Part Write Protect Enabled
Item Help
Menu Level >
↑↓→←
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
By press PageDown/PageUp key you can change the CPU Host/SDRAM/PCI Clock
When jumper setting CPU Host Clock 66MHz you can choose 66/100/33∼99/149/49MHz
When jumper setting CPU Host Clock 100MHz you can choose 100/100/33∼132/132/44MHz
When jumper setting CPU Host Clock 133MHz you can choose 133/100/33∼200/151/50MHz
When jumper setting CPU Host Clock 133MHz you can choose 133/133/33∼200/200/50MHz
11
Page 14
)
)
WARNING!
The Design of this motherboard follows chipset and CPU vender’s design
guideline. Any attempts to push beyond product specification are not
recommended and you are taking your own risk to damage your system or
important data. Before over clocking, you must make sure your
components are able to tolerate such abnormal setting, especially CPU,
memory, hard disks, and VGA cards.
2-4 Install Memory
This motherboard provides two 168-pin DUAL INLINE MEMORY MODULES (DIMM)
sites for memory expansion available from minimum memory size of 32MB to maximum
memory size of 512MB SDRAM.
Valid Memory Configurations
DIMM
SDRAM Clock
100MHz
133MHz
DIMM1 DIMM2
DS DS
SS SS
DS DS
SS SS
According the specification when SDRAM clock is 133MHz only can support 2 pcs
Double Sided DIMMs
DS : Double Sided DIMM
SS : Single Sided DIMM
NOTE!
Make sure the total installed memory does not exceeds 512MB, otherwise the
system may hang during startup.
Generally, installing SDRAM modules to your motherboard is very easy, you can refer to
figure 2-4 to see what a 168-Pin PC100 & PC133 SDRAM module looks like.
DI MM 2 (BANK2 + BANK3
DI MM 1 (BANK0 + BANK1
Figure 2-4
NOTE!
When you install DIMM module fully into the DIMM socket the eject tab
should be locked into the DIMM module very firmly and fit into its
indention on both sides.
12
Page 15
WARNING!
For the SDRAM CLOCK is set at 133MHz, use only PC133-compliant
DIMMs. When this motherboard operate at 133Mhz, most system will not
even boot if non-compliant modules are used because of the strict timing
issues, if your DIMM are not PC133-compliant, set the SDRAM clock to
100MHz to ensure system stability.
2-5 Expansion Cards
WARNING!
2-5-1 Procedure For Expansion Card Installation
1. Read the documentation for your expansion card and make any necessary hardware or
software setting for your expansion card such as jumpers.
2. Remove your computer’s cover and the bracket plate on the slot you intend to use.
3. Align the card’s connectors and press firmly.
4. Secure the card on the slot with the screen you remove above.
5. Replace the computer system’s cover.
6. Set up the BIOS if necessary.
7. Install the necessary software driver for your expansion card.
Turn off your power when adding or removing expansion cards or other
system components. Failure to do so may cause severe damage to both
your motherboard and expansion cards.
2-5-2 Assigning IRQs For Expansion Card
Some expansion cards need an IRQ to operate. Generally, an IRQ must exclusively assign to
one use. In a standard design, there are 16 IRQs available but most of them are already in use.
Standard Interrupt Assignments
IRQ Priority Standard function
0 1 System Timer
1 2 Keyboard Controller
2 N/A Programmable Interrupt
3 * 11 Communications Port (COM2)
4 * 12 Communications Port (COM1)
5 * 13 Sound Card (sometimes LPT2)
6 14 Floppy Disk Controller
7 * 15 Printer Port (LPT1)
8 3 System CMOS/Real Time Clock
9 * 4 ACPI Mode when enabled
10 * 5 IRQ Holder for PCI Steering
11 * 6 IRQ Holder for PCI Steering
12 * 7 PS/2 Compatible Mouse Port
13 8 Numeric Data Processor
14 * 9 Primary IDE Channel
15 * 10 Secondary IDE Channel
* These IRQs are usually available for ISA or PCI devices.
2-5-3 Interrupt Request Table For This Motherboard
13
Page 16
Interrupt request are shared as shown the table below:
INT A INT B INT C INT DINT EINT F INT G INT H
Slot 1
Slot 2
Slot 3
Slot 4
Slot 5
Onboard VGA
Onboard LAN
Onboard USB 0
Onboard USB 1
AC97/MC97
√
√√ √ √
√ √ √ √
IMPORTANT!
If using PCI cards on shared slots, make sure that the drivers
support “Shared IRQ” or that the cards don’t need IRQ assignments.
Conflicts will arise between the two PCI groups that will make the
system unstable or cards inoperable.
Note *1 Either AGP slot or onboard VGA can be active at the same time.
2-5-4 AGP Slot
In 815EDA/815EDAL/815EPDA/815EPDAL motherboards you can plug a 4X AGP
VGA Card into the AGP Slot and the 815EDA/815EDAL will disable on board VGA
automatically once you plug any VGA Card into the motherboard. The special
function of 815EDA/815EDAL boards is support AGP Inline Memory Module in AGP
Slot. By plug in AGP Inline Memory Module which with 4MB of 133MHz SDRAM
display cache, it will improve on board video graphic quality.
2-6 Connectors, Headers
2-6-1 Connectors
AGP SLOT
14
Page 17
(1) Power Connector (20-pin block) : ATXPWR
ATX Power Supply connector. This is a new defined 20-pin connector that usually
comes with ATX case. The ATX Power Supply allows to use soft power on momentary
switch that connect from the front panel switch to 2-pins Power On jumper pole on the
motherboard. When the power switch on the back of the ATX power supply turned on,
the full power will not come into the system board until the front panel switch is
momentarily pressed. Press this switch again will turn off the power to the system
board.
Pin 1
PINROW2 ROW1
1 3.3V 3.3V
2 -12V 3.3V
3 GND GND
4 Soft Power On 5V
5 GND GND
6 GND 5V
7 GND GND
8 -5V Power OK
9 +5V +5V (for Soft Logic)
10 +5V +12V
If you are using a PS/2 mouse, you must purchase an optional PS/2 mouse set which connects
to the 5-pin block and mounts to an open slot on your computer’s case.
(3) USB Port Connector: USB
The connectors are 4-pin connector that connects USB devices to the system board.
(4) LAN Port Connector: LAN (Only for 815EDAL/815EPDAL)
This connector is a standard RJ-45 connector for network.
(5) VGA port Connector: VGA (Only for 815EDA/815EDAL)
This board has VGA port connector it is a 9-pin female D-Subminiature Receptacle connector
for you connect display monitor and computer.
(6) Parallel Port Connector (25-pin female): LPT
Parallel Port connector is a 25-pin D-Subminiature Receptacle connector. The On-board
Parallel Port can be disabled through the BIOS SETUP. Please refer to Chapter 3
“INTEGRATED PERIPHERALS SETUP” section for more detail information.
(7) Audio and Game Connector: GAME
This Connector are 3 phone Jack for LINE-OUT, LINE-IN, MIC and a 15-pin
D-Subminiature Receptacle Connector for joystick/MIDI Device.
Line-out :
Line-in :
Audio input to sound chip
MIC :
Game/MIDI :
Audio output to speaker
Microphone Connector
For joystick or MIDI Device
(8) Serial Port COM1: COM1
COM1 is the 9-pin D-Subminiature mail connector. The On-board serial port can be disabled
through BIOS SETUP. Please refer to Chapter 3 “INTEGRATED PERIPHERALS SETUP“ section for
more detail information.
15
Page 18
ppy
PS/2
Mouse
PRINT GAME/MIDI PORT LAN
MIC
PS/2
Keyboard
USB
VGA COM1
LINE-IN
LINE-OUT
(9) Floppy drive Connector (34-pin block): FDC
This connector supports the provided floppy drive ribbon cable. After connecting the
single plug end to motherboard, connect the two plugs at other end to the floppy drives.
FDC
Pin 1
Flo
Drive Connector
(10) Primary IDE Connector (40-pin block): IDE1
This connector supports the provided IDE hard disk ribbon cable. After connecting the
single plug end to motherboard, connect the two plugs at other end to your hard disk(s).
If you install two hard disks, you must configure the second drive to Slave mode by
setting its jumpers accordingly. Please refer to the documentation of your hard disk for
the jumper settings.
(11) Secondary IDE Connector (40-pin block): IDE2
This connector connects to the next set of Master and Slave hard disks. Follow the
same procedure described for the primary IDE connector. You may also configure two
hard disks to be both Masters using one ribbon cable on the primary IDE connector and
another ribbon cable on the secondary IDE connector.
Secondary IDE Connector
IDE1 IDE2
Pin 1Pin 1
Primary IDE Connector
16
Page 19
N
Two hard disks can be connected to each connector. The first HDD is referred to as the
•
“Master” and the second HDD is referred to as the “Slave”.
For performance issues, we strongly suggest you don’t install a CD-ROM or DVD-ROM
•
drive on the same IDE channel as a hard disk. Otherwise, the system performance on this
channel may drop.
2-6-2 Headers
(1) Serial Port2 COM2 Header (9-pin): COM2
Serial Port2 COM2 Header
(2) USB Port Headers (9-pin): USB1
These headers are used for connecting the additional USB port plug. By attaching an
option USB cable, your can be provided with two additional USB plugs affixed to the
back panel.
COM 2
Pi n 1
USB1
Pin 1
VCC
GND
DATA
-
+ DATA
VCC
GND
DATA
-
+ DATA
USB Port Headers
ote: Orient the read marking on the
COM2 ribbon cable to pin 1
OC
(3) IDE Activity LED: IDE LED
This connector connects to the hard disk activity indicator light on the case.
(4) Reset switch lead: RESET
This 2-pin connector connects to the case-mounted reset switch for rebooting your computer
without having to turn off your power switch. This is a preferred method of rebooting in order
to prolong the lift of the system’s power supply. See the figure below.
(5) Speaker connector: SPEAK
This 4-pin connector connects to the case-mounted speaker. See the figure below.
(6) Power LED: PWR LED
The Power LED is light on while the system power is on. Connect the Power LED from the
system case to this pin.
17
Page 20
R
(7) Power switch: PWR BTN
This 2-pin connector connects to the case-mounted power switch to power ON/OFF the system.
PWRBTN
PWR LED
GND
VCC5
PWRLED
FP SPEAK
Pin 1
PWRBT N
Pin 1
NC
GND
SPK
NC
GND
VCC5
RST SW
HDDLED
RESET
HDLED
VCC5
System Case Connections
(8) Wake On-LAN Headers (3-pin) : WOL
This connector connects to a LAN card with a WAKE ON-LAN output. This connector
power up the system when a wake up signal is received through the LAN card.
NOTE:
This feature requires that BIOS Wake-Up by PCI Card is enabled.
5VSB
GND
WOL
WOL
13
Wake-On-LAN Headers
(9) FAN Speed Headers (3-pin) : FAN1, FAN2, FAN3
These connectors support cooling fans of 350mA (4.2 Watts) or less, depending on the
fan manufacturer, the wire and plug may be different. The red wire should be positive,
while the black should be ground. Connect the fan’s plug to the board taking into
consideration the polarity of connector.
13
FAN1
13
FAN2
13
FAN3
18
Page 21
(10) IR infrared module Headers (5-pin) : IR
This connector supports the optional wireless transmitting and receiving infrared
module. You must configure the setting through the BIOS setup to use the IR function.
IR infrared module Headers
IR
Pin 1
(11) CD Audio-In Headers (4-pin) : CDIN
CDIN is the connector for CD-Audio Input signal. Please connect it to CD-ROM CD-
Audio output connector.
CDI N
1
2
NC
4
GND
IRRX
6
5
IRTX
VCC5
CD Audio-In Headers
19
Page 22
2-7 Starting Up Your Computer
1. After all connections are made, close your computer case cover.
2. Be sure all the switch are off, and check that the power supply input voltage is set to
proper position, usually in-put voltage is 220V∼240V or 110V∼120V depending on your
country’s voltage used.
3. Connect the power supply cord into the power supply located on the back of your system
case according to your system user’s manual.
4. Turn on your peripheral as following order:
a. Your monitor.
b. Other external peripheral (Printer, Scanner, External Modem etc…)
c. Your system power. For ATX power supplies, you need to turn on the power supply
and press the ATX power switch on the front side of the case.
5. The power LED on the front panel of the system case will light. The LED on the monitor
may light up or switch between orange and green after the system is on. If it complies
with green standards or if it is has a power standby feature. The system will then run
power-on test. While the test are running, the BIOS will alarm beeps or additional
message will appear on the screen.
If you do not see any thing within 30 seconds from the time you turn on the power. The
system may have failed on power-on test. Recheck your jumper settings and connections
or call your retailer for assistance.
Beep Meaning
One short beep when displaying logo No error during POST
Long beeps in an endless loop No DRAM install or detected
One long beep followed by three short
beeps
High frequency beeps when system is
working
Video card not found or video card memory
bad
CPU overheated
System running at a lower frequency
6. During power-on, press <Delete> key to enter BIOS setup. Follow the instructions in
BIOS SETUP.
7.
Power off your computer:
You must first exit or shut down your operating system
before switch off the power switch. For ATX power supply, you can press ATX power
switching after exiting or shutting down your operating system. If you use Windows 9X,
click
“Start”
button, click
“Shut down”
and then click
“Shut down the computer?”
The power supply should turn off after windows shut down.
20
Page 23
Chapter 3
Introducing BIOS
The BIOS is a program located on a Flash Memory on the motherboard. This program is a
bridge between motherboard and operating system. When you start the computer, the BIOS
program gain control. The BIOS first operates an auto-diagnostic test called POST (power on
self test) for all the necessary hardware, it detects the entire hardware device and configures
the parameters of the hardware synchronization. Only when these tasks are completed done it
gives up control of the computer to operating system (OS). Since the BIOS is the only
channel for hardware and software to communicate, it is the key factor for system stability,
and in ensuring that your system performance as its best.
In the BIOS Setup main menu of Figure 3-1, you can see several options. We will explain
these options step by step in the following pages of this chapter, but let us first see a short
description of the function keys you may use here:
Press <Esc> to quit the BIOS Setup.
•
•
Press
↑↓←→
(up, down, left, right) to choose, in the main menu, the option you want to
confirm or to modify.
Press <F10> when you have completed the setup of BIOS parameters to save these
•
parameters and to exit the BIOS Setup menu.
Press Page Up/Page Down or +/– keys when you want to modify the BIOS parameters for
•
the active option.
3-1 Entering Setup
Power on the computer and by pressing <Del> immediately allows you to enter Setup.
If the message disappears before your respond and you still wish to enter Setup, restart the
system to try again by turning it OFF then ON or pressing the “RESET” button on the system
case. You may also restart by simultaneously pressing <Ctrl>, <Alt> and <Delete> keys. If
you do not press the keys at the correct time and the system does not boot, an error message
will be displayed and you will again be asked to
Press <F1> to continue, <Ctrl-Alt-Esc> or <Del> to enter Setup
3-2 Getting Help
Main Menu
The on-line description of the highlighted setup function is displayed at the bottom of the
screen.
Status Page Setup Menu/Option Page Setup Menu
Press F1 to pop up a small help window that describes the appropriate keys to use and the
possible selections for the highlighted item. To exit the Help Window, press <Esc>.
21
Page 24
3-3 The Main Menu
Once you enter Award BIOS CMOS Setup Utility, the Main Menu (Figure 3-1) will appear
on the screen. The Main Menu allows you to select from fourteen setup functions and two
exit choices. Use arrow keys to select among the items and press <Enter> to accept or enter
the sub-menu.
CMOS Setup Utility – Copyright(C) 1984-2002 Award Software
Standard CMOS Features
Advanced BIOS Features
Advanced Chipset Features
Integrated Peripherals
Power Management Setup
PnP/PCI Configurations
PC Health Status
Esc : Quit
F10 : Save & Exit Setup
Time, Date, Hard Disk Type…
Miscellaneous Control
Load optimized Defaults
Load Standard Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
Exit Without Saving
↑↓→ ←
Figure 3-1
: Select Item
Standard CMOS Features
Use this Menu for basic system configurations.
Advanced BIOS Features
Use this menu to set the Advanced Features available on your system.
Advanced Chipset Features
Use this menu to change the values in the chipset registers and optimize your system’s
performance.
Integrated Peripherals
Use this menu to specify your settings for integrated peripherals.
Power Management Setup
Use this menu to specify your settings for power management.
PnP/PCI configurations
This entry appears if your system supports PnP/PCI.
PC Health Status
This entry shows your PC health status.
Miscellaneous Control
Use this menu to specify your settings for Miscellaneous Control.
Load Optimized Defaults
Use this menu to load the BIOS default values that are factory settings for optimal
performances system operations.
22
Page 25
Load Standard Defaults
Use this menu to load the BIOS default values for the minimal/stable performance system
operation.
Set Supervisor/User Password
Use this menu to set User and Supervisor Passwords.
Save & Exit Setup
Save CMOS value changes to CMOS and exit setup.
Exit Without Saving
Abandon all CMOS value changes and exit setup.
3-4 Standard CMOS Features
The items in Standard CMOS Setup Menu are divided into several categories. Each category
includes no, one or more than one setup items. Use the arrow keys to highlight the item and
then use the <PgUp> or <PgDn> keys to select the value you want in each item.
CMOS Setup Utility – Copyright(C) 1984-2002 Award Software
Standard CMOS Features
Date (mm:dd:yy) Fri, Jul, 19 2002
Time (hh:mm:ss) 13 : 58 : 12
IDE Primary Master
IDE Primary Slave
IDE Secondary Master
IDE Secondary Slave
Drive A 1.4M, 3.25 in.
Drive B None
Video EGA/VGA
Halt On All Errors
Base Memory 640K
Extended Memory 64512K
Total Memory 65536K
Item Help
Menu Level >
Change the day, moth,
Year and century
↑↓→←
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
Day of the week, from Sun to Sat, determined by BIOS. Read-only.
Day
Month
Date
Year
The month from Jan. through Dec.
The date from 1 to 31 can be keyed by numeric function keys.
The year depends on the year of the BIOS.
Time
The time format is <hour><minute><second>.
Primary Master/Primary Slave
23
Page 26
Secondary Master/Secondary Slave
Press PgUp/<+>or PgDn/<–>to select Manual, None, Auto type. Note that the specifications
of your drive must match with the drive table. The hard disk will not work properly if you
enter improper information for this category. If your hard disk drive type is not matched or
listed, you can use Manual to define your own drive type manually.
If you select Manual, related information is asked to be entered to the following items. Enter
the information directly from the keyboard. This information should be provided in the
documentation from your hard disk vendor or the system manufacturer.
If the controller of HDD interface is SCSI, the selection shall be “None”.
If the controller of HDD interface is CD-ROM, the selection shall be “None”
Access Mode
Cylinder
Head
Precomp
Landing Zone
Sector
number of sectors
The settings are Auto Normal, Large, and LBA.
number of cylinders
number of heads
write precomp
landing zone
3-5 Advanced BIOS Features
CMOS Setup Utility – Copyright(C) 1984-2002 Award Software
Advanced BIOS Features
Anti-Virus Protection Disabled
PhoenixNet Support Disabled
CPU L1 Cache Enabled
CPU L2 Cache Enabled
CPU L2 Cache ECC Checking Disabled
Processor Number Feature Enabled
Quick Power On Self Test Enabled
First Boot Device Floppy
Second Boot Device HDD-0
Third Boot Device LS120
Fouth Boot Device Disabled
Swap Floppy Drive Disabled
Boot Up Floppy Seek Enabled
Boot Up NumLock Status On
Gate A20 Option Fast
Typematic Rate Setting Disabled
Typematic Rate (Chars/Sec) 6
Typematic Delay (Msec) 250
Security Option Setup
OS Select For DRAM > 64MB Non-OS2
HDD S.M.A.R.T. Capability Disabled
Report No FDD For Win 95 No
↑↓→←
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
Allows you to choose
the VIRUS warning
feature for IDE Hard
disk boot sector
protection. If this
function is enabled
and someone attempt to
write data into this
area, BIOS will show a
warning message on
screen and alarm beep
Anti-Virus Protection
24
Page 27
Allows you to choose the VIRUS Warning feature for IDE Hard Disk boot sector protection. If this
function is enabled and someone attempt to write data into this area, BIOS will show a warning
message on screen and alarm beep.
Disabled
(default) No warning message to appear when anything attempts to access the boot
sector or hard disk partition table.
Enabled
Activates automatically when the system boots up causing a warning
message to appear when anything attempts to access the boot sector of hard
disk partition table.
CPU L1 Cache
The default value is Enabled.
Enabled
Disabled
(default) Enable cache
Disable cache
Note: The L1 cache is built in the processor.
CPU L2 Cache
Choose Enabled or Disabled. This option enables the Level 2 cache memory.
CPU L2 Cache ECC Checking
Choose Enabled or Disabled. This option enables the Level 2 cache memory ECC (error check
correction).
Processor Number Feature
This option is for Pentium III processor. During Enabled, this will check the CPU Serial number.
Disabled this option if you don’t want the system to know the Serial number.
Quick Power On Self-Test
This category speeds up Power On Self Test (POST) after you power on the computer. If this is set to
Enabled. BIOS will shorten or skip some check items during POST.
Enabled
Disabled
(default) Enable quick POST
Normal POST
First/Second/Third/Fourth Boot Device
The BIOS attempts to load the operating system from the devices in the sequence selected in these
items. The settings are Floppy, LS/ZIP, HDD-0/HDD-1/HDD-3, SCSI, CDROM, LAN and Disabled.
Swap Floppy Drive
Switches the floppy disk drives between being designated as A and B. Default is Disabled.
Boot Up Floppy Seek
During POST, BIOS will determine if the floppy disk drive installed is 40 or 80 tracks. 360K type is
40 tracks while 760K, 1.2M and 1.44M are all 80 tracks.
Boot Up NumLock Status
The default value is On.
(default)
On
Off
Keypad is numeric keys.
Keypad is arrow keys.
Gate A20 Option
Normal
(default) The A20 signal is controlled by port 92 or chipset specific method.
Fast
The A20 signal is controlled by keyboard controller or chipset hardware.
Typematic Rate Setting
Keystrokes repeat at a rate determined by the keyboard controller. When enabled, the typematic rate
and typematic delay can be selected. The settings are: Enabled/Disabled.
Typematic Rate (Chars/Sec)
Sets the number of times a second to repeat a keystroke when you hold the key down. The settings
are: 6, 8, 10, 12, 15, 20, 24, and 30.
25
Page 28
Typematic Delay (Msec)
Sets the delay time after the key is held down before is begins to repeat the keystroke. The settings
are 250, 500, 750, and 1000.
Security Option
This category allows you to limit access to the system and Setup, or just to Setup.
System
The system will not boot and access to Setup will be denied if the correct
password is not entered at the prompt.
(default) The system will boot, but access to Setup will be denied if the correct
Setup
password is not entered prompt.
OS Select For DRAM > 64MB
Allows OS2 to be used with >64MB or DRAM. Settings are Non-OS/2 (default) and OS2. Set to
OS/2 if using more than 64MB and running OS/2.
Report No FDD For Win 95
Whether report no FDD for Win 95 or not. The settings are: Yes, No.
3-6 Advanced Chipset Features
The Advanced Chipset Features Setup option is used to change the values of the chipset
registers. These registers control most of the system options in the computer.
CMOS Setup Utility – Copyright(C) 1984-2002 Award Software
Advanced Chipset Features
On-Chip VGA Setting Press Enter
SDRAM Timing Setting Press Enter
System BIOS Cacheable Enabled
Video BIOS Cacheable Enabled
Memory Hole at 15M-16M Disabled
CPU Latency Timer Disabled
Delayed Transaction Disabled
AGP Mode Select Auto
AGP Graphics Aperture Size 64MB
↑↓→←
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
Note: Change these settings only if you are familiar with the chipset.
SDRAM Timing Setting
Please refer to section 3-6-1
System BIOS Cacheable
Selecting Enabled allows caching of the system BIOS ROM at F0000h-FFFFFh, resulting in better
system performance. However, if any program writes to this memory area, a system error may result.
The settings are: Enabled and Disabled.
Video BIOS Cacheable
Select Enabled allows caching of the video BIOS, resulting in better system performance. However,
if any program writes to this memory area, a system error may result. The settings are: Enabled and
Disabled.
Memory Hole At 15M-16M
26
Page 29
You can reserve this area of system memory for ISA adapter ROM. When this area is reserved, it
cannot be cached. The user information of peripherals that need to use this area of system memory
usually discusses their memory requirements. The settings are: Enabled and Disabled.
CPU Latency Timer
During Enabled, A deferrable CPU cycle will only be Deferred after it has been in a Snoop Stall for
31 clocks and another ADS# has arrived. During Disabled, A deferrable CPU cycle will be Deferred
immediately after the GMCH receives another ADS#.
Delayed Transaction
The chipset has an embedded 32-bit posted write buffer to support delay transactions cycles. Select
Enabled to support compliance with PCI specification version 2.1. The settings are: Enabled and
Disabled.
On-Chip Video Window Size
This option enabled/disabled the on-chip video windows size for VGA driver use. The settings are:
enabled, Disabled.
AGP Graphics Aperture Size
This option determines the effective size of the graphics aperture used in the particular PAC
configuration. The AGP aperture is memory-mapped, while graphics data structure can reside in a
graphics aperture. The aperture range should be programmed as not cacheable in the processor cache,
accesses with the aperture range are forwarded to the main memory, then PAC will translate the
original issued address via a translation table that is maintained on the main memory. The option
allows the selection of an aperture size of 32MB, 64MB.
3-6-1 SDRAM Timing Setting
CMOS Setup Utility – Copyright(C) 1984-2002 Award Software
SDRAM Timing Setting
SDRAM CAS Latency Time 3
SDRAM Cycle Time Tras/Trc 6/8
SDRAM RAS-to-CAS Delay 3
SDRAM RAS Precharge Time 3
DRAM CTL Buffer strengths Normal
DRAM MD Buffer strengths Normal
↑↓→←
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
When synchronous DRAM is installed, the number of clock cycles of CAS latency depends on the
DRAM timing. The settings are: 2 and 3.
SDRAM Cycle Time Tras/Trc
Select the number of SCLKs for an access cycle. The settings are: 5/7 and 6/8.
Item Help
Menu Level >>
27
Page 30
SDRAM RAS-to-CAS Delay
This field let’s you insert a timing delay between the CAS and RAS strobe signals, used when DRAM
is written to, read from, or refreshed. Fast gives faster performance; and Slow gives more stable
performance. This field applies only when synchronous DRAM is installed in the system. The
settings are: 2 and 3.
SDRAM RAS Precharge Time
If an insufficient number of cycles is allowed for the RAS to accumulate its charge before DRAM
refresh, the refresh may be incomplete and the DRAM may fail to retain date. Fast gives faster
performance; and Slow gives more stable performance. This field applies only when synchronous
DRAM is installed in the system. The settings are: 2 and 3.
3-7 Integrated Peripherals
CMOS Setup Utility – Copyright(C) 1984-2002 Award Software
Integrated Peripherals
On-Chip IDE Function Press Enter
On-Chip SIO Function Press Enter
On-Chip Device Function Press Enter
Init Display First PCI Slot
Power On Function BUTTON ONLY
KB Power ON Password Enter
Hot Key Power ON Ctrl-F1
POWER After PWR-fail off
↑↓→←
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
This item allows you to decide to activate whether PCI Slot or on-chip VGA first. The settings are:
PCI Slot, AGP Slot, On-Chip VGA.
Power On Function
This function allows you to select the item to power on the system. The settings are: Button Only,
Mouse Left, Mouse Right, Password, Hotkey, and keyboard 98.
Power After PWR-Fail
This option will determine how the system will power on after a power failure.
28
Page 31
3-7-1 On-Chip IDE Function
CMOS Setup Utility – Copyright(C) 1984-2002 Award Software
On-Chip IDE Function
On-Chip Primary PCI IDE Enabled
On-Chip Secondary PCI IDE Enabled
IDE Primary Master PIO Auto
IDE Primary Slave PIO Auto
IDE Secondary Master PIO Auto
IDE Secondary Slave PIO Auto
IDE Primary Master UDMA Auto
IDE Primary Slave UDMA Auto
IDE Secondary Master UDMA Auto
IDE Secondary Slave UDMA Auto
IDE 32-bit Transfer Mode Enabled
IDE HDD Block Mode Enabled
Delay For HDD (Secs) 0
↑↓→←
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
The integrated peripheral controller contains an IDE interface with support for two IDE channels.
Select Enabled to activate each channel separately. The settings are: Enabled and Disabled.
IDE Primary/Secondary Master/Slave PIO
The four IDE PIO (Programmed Input/Output) fields let you set a PIO mode (0-4) for each of the four
IDE devices that the onboard IDE interface supports. Modes 0 through 4 provide successively
increased performance. In Auto mode, the system automatically determines the best mode for each
device. The settings are: Auto, Mode 0, Mode 1, Mode 2, Mode 3, Mode 4.
IDE Primary/Secondary Master/Slave UDMA
Ultra DMA/33 implementation is possible only if your IDE hard drive supports it and the operating
environment includes a DMA driver (Windows 95 OSR2 or a third-party IDE bus master driver). If
your hard drive and your system software both support Ultra DMA/33 and Ultra DMA/66, select Auto
to enable BIOS support. The settings are: Auto, Disabled.
IDE HDD Block Mode
Block mode is also called block transfer, multiple commands, or multiple sector read/write. If your
IDE hard drive supports block mode (most new drives do), select Enabled for automatic detection of
the optimal number of block read/writes per sector the drive can support. The settings are: Enabled,
Disabled.
3-7-2 On-Chip SIO Function
CMOS Setup Utility – Copyright(C) 1984-2002 Award Software
On-Chip SIO Function
Onboard FDD Controller Enabled
Onboard Serial Port 1 3F8/IRQ4
Onboard Serial Port 2 2F8/IRQ3
UART Mode Select Normal
UR2 Duplex Mode Half
Onboard Parallel Port 378/IRQ7
Parallel Port Mode SPP
ECP Mode Use DMA 3
↑↓→←
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
Select Enabled if your system has a floppy disk controller (FDD) installed on the system board and
you wish to use it. If you install add-on FDC or the system has no floppy drive, select Disabled in this
field. The settings are: Enabled and Disabled.
Onboard Serial Port 1/Port 2
Select an address and corresponding interrupt for the first and the second serial ports. The settings
are: 3F8/IRQ4, 2E8/IRQ3, 3E8/IRQ4, 2F8/IRQ3, Disabled, Auto.
UART Mode Select
This item allows you to determine which InfraRed (IR) function of the onboard I/O chip, this
functions uses.
Onboard Parallel Port
There is a built-in parallel port on the on-board Super I/O chipset that Provides Standard, ECP, and
EPP features. It has the following option:
Disabled
(3BCH/IRQ7)/
(278H/IRQ5)/
(378H/IRQ7)
Line Printer port 0
Line Printer port 2
Line Printer port 1
Parallel Port Mode
SPP : Standard Parallel Port
EPP : Enhanced Parallel Port
ECP : Extended Capability Port
SPP/EPP/ECP/ECP+EPP
To operate the onboard parallel port as Standard Parallel Port only, choose “SPP.” To operate the
onboard parallel port in the EPP modes simultaneously, choose “EPP.” By choosing “ECP”, the
onboard parallel port will operate in ECP mode only. Choosing “ECP+EPP” will allow the
onboard parallel port to support both the ECP and EPP modes simultaneously. The ECP mode
has to use the DMA channel, so choose the onboard parallel port with the ECP feature. After
selecting it, the following message will appear: “ECP Mode Use DMA” at this time, the user can
choose between DMA channels 3 to 1. The onboard parallel port is EPP Spec. compliant, so
after the user chooses the onboard parallel port with the EPP function, the following message will
be displayed on the screen: “EPP Mode Select.” At this time either EPP 1.7 spec. or EPP 1.9
spec. can be chosen.
3-7-3 On-Chip Device Function
CMOS Setup Utility – Copyright(C) 1984-2002 Award Software
On-Chip Device Function
USB Controller Enabled
USB Keyboard Support Disabled
** Onboard AC97 Codec is ALC100/200 **
AC97 Sound Enabled
AC97 Modem Auto
Game Port Address 201
Midi Port Address 330
Midi Port IRQ 10
↑↓→←
USB Controller
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have a USB
peripherals. The settings are: Enabled, Disabled.
USB Keyboard Support
Select Enabled if your system contains a Universal Serial Bus (USB) controller and you have a USB
keyboard. The settings are: Enabled, Disabled.
AC97 Sound
This item allows you to decide to enable/disable the 815 chipset family to support AC97 Audio. The
settings are: Enabled, Disabled.
AC97 Modem
This item allows you to decide to enable/disable the 815 chipset family to support AC97 Modem.
The settings are: Enabled, Disabled.
Game Port Address/Midi Port Address
This will determine which Address the Game Port/Midi Port will use.
3-8 Power Management Setup
The Power Management Setup allows you to configure your system to most effectively save
energy saving while operating in a manner consistent with your own style of computer use.
CMOS Setup Utility – Copyright(C) 1984-2002 Award Software
Power Management Setup
ACPI Function Enabled
Power Management User Define
Video Off Method DPMS
Video Off In Suspend Yes
Suspend Type Stop Grant
MODEM Use IRQ 3
Suspend Mode Disabled
HDD Power Down Disabled
Soft-off by PWR-BTTN Instant-off
Wake-Up by PCI card Disabled
Power On by Ring Disabled
Resume by Alarm Disabled
x Date (of Month) Alarm 0
x Time (hh:mm:ss) Alarm 0 : 0 : 0
> PM Timer Reload Events Press Enter
↑↓→←
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
This item allows you to Enabled/Disabled the Advanced Configuration and Power Management (ACPI).
The settings are Enabled and Disabled.
Item Help
Menu Level >
Power Management
This category allows you to select the type (or degree) of power saving which is directly related to the
following modes:
1. Suspend Mode
2. HDD Power Down
There are three selections for Power Management, two of which have fixed mode settings.
31
Page 34
Min Saving
Minimum power management. Suspend Mode=1 hr., and HDD Power
Down=15 min.
Max Saving
Maximum power management. Suspend Mode=1 min., and HDD Power
Down=1 min.
User Define
(default) Allows you to set each mode individually. When not disabled, each of the
ranges is from 1 min. to 1hr. except for HDD Power Down that ranges
from 1 min. to 15 min. and disable.
Video Off Method
This determines the manner in which the monitor is blanked.
V/H SYNC+Blank
This selection will cause the system to turn off the vertical and horizontal
synchronization ports and write blanks to the video buffer.
Blank Screen
DPMS
(default) Initial display power management signaling.
This option only writes blanks to the video buffer.
Video Off In Suspend
This determines the manner in which the monitor is blanked. The settings are: Yes and No.
Suspend Type
Select the Suspend Type.
The settings are: PWRON Suspend, Stop Grant.
Modem Use IRQ
This determines the IRQ in which the MODEM can use.
The settings are: 3, 4, 5, 7, 9, 10, 11, NA.
Suspend Mode
When enabled and after the set time of system inactivity, all devices except the CPU will be shut off.
The settings are: l/2/4/8/12/20/30/40 Min, 1 Hour, and Disabled.
HDD Power Down
When enabled and after setting time of system inactivity, the hard disk drive will be powered down
while all the other devices remain active.
The settings are: 1/2/3/4/5/6/7/8/9/10/11/12/13/14/15 Min and Disabled.
Soft-Off by PWR-BTTN
Pressing the power button for more than 4 seconds forces the system to enter the Soft-Off state. The
settings are: Delay 4 Sec, Instant-Off.
Wake Up by PCI card
This will enable the system to wake up to PCI LAN Card.
The settings are: Enabled and Disabled.
Power On by Ring
During Disabled, the system will ignore any incoming call from the modem. During Enabled, the
system will boot up if there’s an incoming call from the modem.
CPU Thermal-Throttling
Select the CPU THRM-Throttling rate. The settings are: 12.5%, 25.0%, 37.5%, 50.0%, 62.5%, 75.0%,
87.5%.
Resume by Alarm
This function is for setting date and time for your computer to boot up. During Disabled, you cannot
use this function. During Enabled, choose the Date and Time Alarm:
Date(of month) Alarm
You can choose which month the system will boot up. Set to 0, to boot every day.
Time(hh:mm:ss) Alarm
You can choose what hour, minute and second the system will boot up.
Note: If you have change the setting, you must let the system boot up until it goes to the
32
Page 35
operating system, before this function will work.
PM Timer Reload Events
Pm Timer Reload events are I/O events whose occurrence can prevent the system from entering a
power saving mode or can awaken the system from such a mode. In effect, the system remains alert
for anything which occurs to a device which is configured as Enabled, even when the system is in a
power down mode.
Primary IDE 0
Primary IDE 1
Secondary IDE 0
Secondary IDE 1
FDD, COM, LPT Port
PCI PIRQ[A-D] #
3-9 PnP/PCI Configuration Setup
This section describes configuring the PCI bus system. PCI, or Personal Computer
Interconnect, is a system which allows I/O devices to operate at speeds nearing the speed the
CPU itself uses when communicating with its own special components. This section covers
some very technical items and it is strongly recommended that only experienced users should
make any changes to the default settings.
CMOS Setup Utility – Copyright(C) 1984-2002 Award Software
PnP/PCI Configurations
Reset Configuration Data Disabled
Resources Controlled By Manual
> IRQ Resources Press Enter
PCI/VGA Palette Snoop Disabled
↑↓→←
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
Normally, you leave this field Disabled. Select Enabled to reset Extended System Configuration Data
(ESCD) when you exit Setup if you have installed a new add-on and the system reconfiguration has
caused such a serious conflict that the operating system can not boot. The settings are: Enabled and
Disabled.
Resource Controlled By
The Award Plug and Play BIOS has the capacity to automatically configure all of the boot and Plug
and Play compatible devices. However, this capability means absolutely nothing unless you are using
a Plug and Play operating system such as Windows95/98. If you set this field to “manual” choose
specific resources by going into each of the sub menu that follows this field (a sub menu is preceded
by a “>”).
The settings are: Auto (ESCD), Manual.
IRQ Resources
33
Page 36
When resources are controlled manually, assign each system interrupt a type, depending on the type
of device using the interrupt.
DMA Resources
This sub menu can let you control the DMA resource.
PCI/VGA Palette Snoop
Leave this field at Disabled. The settings are Enabled, Disabled.
3-10 PC Health Status
This section shows the Status of you CPU, Fan, Warning for overall system status. This is
only available if there is Hardware Monitor onboard.
CMOS Setup Utility – Copyright(C) 1984-2002 Award Software
PC Health Status
Show PC Health in Post Enabled
Shutdown Temperature Disabled
Vcore 1.65V
Vcc 1.8V 1.85V
VCC 3.3V 3.3V
VCC 5V 4.97V
+12V 11.90V
-12V (-)12.03V
-5V (-) 5.10V
5VSB 4.97V
Vbat 3.29V
System Temperature 25°C
CPU Temperature 35°C
FAN1 Speed 5843 RPM
FAN2 Speed 6132 RPM
FAN3 Speed 5720 RPM
↑↓→←
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
During Enabled, this will warn the user when the CPU temperature reaches a certain temperature.
Current System Temp/Current CPU Temperature/Current FAN1, FAN2, FAN3 Speed/
Vcore/VTT/3.3V/+5V/+12V/-12V/ -5V/VBAT(V)/5VSB(V)
This will show the CPU/FAN/System voltage chart and FAN Speed.
Shutdown Temperature
This option is for setting the Shutdown temperature level for the processor. When the processor
reaches the temperature you set, this will shutdown the system.
3-11 Miscellaneous Control
34
Page 37
This section is for setting CPU Miscellaneous Control.
CMOS Setup Utility – Copyright(C) 1984-2002 Award Software
Miscellaneous Control
Cyrix III Clock Ratio Default
Auto Detect DIMM/PCI Clk Enabled
Spread Spectrum Disabled
** Current Host Clock is 133 Mhz **
CPU Host/SDRAM/PCI Clock 133/133/33(by HW jumper)
CPU Clock Ratio X 3
Flash Part Write protect Enabled
Item Help
Menu Level >
↑↓→←
Auto Detect DIMM/PCI Clk
This item allows you to enable/disable auto detect DIMM/PCI Clock.
The settings are: Enabled, Disabled.
Spread Spectrum
This item allows you to set the Spread Spectrum.
CPU/SDRAM/PCI Clock
This item allows you to select the CPU/SDRAM/PCI Clock, refer to Page 11.
By press PageDown/PageUp key you can change the CPU Host/SDRAM/PCI Clock
When jumper setting CPU Host Clock 66MHz you can choose 66/100/33∼99/149/49MHz
When jumper setting CPU Host Clock 100MHz you can choose 100/100/33∼132/132/44MHz
When jumper setting CPU Host Clock 133MHz you can choose 133/133/33∼200/200/50MHz
When jumper setting CPU Host Clock 133MHz you can choose 133/100/33∼200/151/50MHz
CPU Clock Ratio
This item allows you to select the CPU ratio.
Flash Part Write Protect
This item allow you protect BIOS data, please setting Disabled before upgrade BIOS
Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
When you press <Enter> on this item, you get confirmation dialog box with a message similar to:
Load Standard Defaults (Y/N)? N
Pressing <Y> loads the BIOS default values for the most stable, minimal-performance system
operations.
Load Optimized Defaults
When you press <Enter> on this item, you get a confirmation dialog box with a message similar to:
Load Optimized Defaults (Y/N)? N
Pressing <Y> loads the default values that are factory settings for optimal performance system
operations.
3-13 Set Supervisor/User Password
You can set either supervisor or user password, or both of them. The differences are:
35
Page 38
Supervisor password: Can enter and change the options of the setup menus.
User password: Can only enter but do not have the right to change the options of the
setup menus. When you select this function, the following message
will appear at the center of the screen to assist you in creating a
password.
ENTER PASSWORD:
Type the password, up to eight characters in length, and press <Enter>. The password typed
now will clear any previously entered password from CMOS memory. You will be asked to
confirm the password. Type the password again and press <Enter>. You may also press
<Esc> to abort the selection and not enter a password.
To disable a password, just press <Enter> when you are prompted to enter the password. A
message will confirm that the password will be disabled. Once the password is disabled, the
system will boot and you can enter Setup freely.
PASSWORD DISABLED.
When a password has been enabled, you will be prompted to enter it every time you try to
enter Setup. This prevents an unauthorized person from changing any part of your system
configuration.
Additionally, when a password is enabled, you can also require the BIOS to request a
password every time your system is rebooted. This would prevent unauthorized use of your
computer.
You determine when the password is required within the BIOS Features Setup Menu and its
Security option. If the Security option is set to “System”, the password will be required both
at boot and at entry to Setup. If set to “Setup”, prompting only occurs when trying to enter
Setup.
Chapter 4
DRIVER & FREE PROGRAM INSTALLATION
36
Page 39
Check your package and there is A MAGIC INSTALL CD included. This CD consists of all
DRIVERS you need and some free application programs and utility programs. In addition, this
CD also include an auto detect software which can tell you which hardware is installed, and
which DRIVERS needed so that your system can function properly. We call this auto detect
software MAGIC INSTALL.
MAGIC INSTALL supports WINDOWS 95/98/98SE/NT4.0/2000
Insert CD into your CD-ROM drive and the MAGIC INSTALL Menu should appear as below.
If the menu does not appear, double-click MY COMPUTER / double-click CD-ROM drive or
click START / click RUN / type X:\SETUP.EXE (assuming X is your CD-ROM drive).
From MAGIC INSTALL MENU you may make 11 selections:
8. PC-CILLIN install PC-CILLIN 2002 anti-virus program
9. DIRECTX8 install Microsoft DirectX 8.0 driver
10. BROWSE CD to browse the contents of the CD
11. EXIT to exit from MAGIC INSTALL menu
Each selection is illustrated as below:
4-1 INF install INTEL 815 chipset system driver
After you have completed the installation of your operation system (WINDOWS 95/98/ 98SE).
You will find an UNKNOWN DEVICE in the device manager (START/SETTING/
37
Page 40
CONTROL PANEL/SYSTEM/DEVICE MANAGER). You have to install INF driver as
shown below:
1. Click INF in the MAGIC INSTALL MENU 2. Click NEXT when Chipset Software Install
Utility appears
3. This chart shows motherboards supported
by the driver click NEXT
NOTE: MAGIC INSTALL will auto detect file path X:\INTEL815\INF\INFINST.EXE
This driver supports WINDOWS 95/98/98SE/ME/2000 (NT4.0 do not require)
4. Select if you want computer re-started
click Finish
4-2 IDE install Intel ULTRA ATA Storage driver
38
Page 41
1. Click IDE when MAGIC INSTALL MENU
appears
3. This is to announce the Copy Right click
NEXT
2. Click NEXT when INTEL Ultra ATA Storage
Wizard appears
4. Click NEXT or BROWSE to change the path
you want the driver stored
5. Select if you want to re-start your computer
and click Finish
NOTE: MAGIC INSTALL will auto detect file path X:\INTEL815\IDE\SETUP.EXE
This driver supports WINDOWS 95/98/98SE/ME/NT4.0/2000
6. You may choose to remove the driver or you
may remove it at ADD/REMOVE
PROGRAMS
4-3 VGA install on-board VGA driver (Only for
815EDA/815EDAL)
39
Page 42
1. Click VGA when MAGIC INSTALL MENU
appears
2. Click NEXT when INTEL 81X Family
Chipset Graphics Driver Software appears
3. Click NEXT, this is to announce Copy Right 4. Select if you want to re-start computer and
click Finish
NOTE: The path of the file
for WIN95 is X:\INTEL815\VGA\WIN95\SETUP.EXE
for WIN98 and WIN98SE is X:\INTEL815\VGA\WIN9X\SETUP.EXE
for NT4.0 is X:\INTEL815\VGA\NT40\SETUP.EXE
for Windows 2000 is X:\INTEL815\VGA\WIN2K\SETUP.EXE
4-4 AC97 sound driver and the program install for
editing/playback
1. Click SOUND when MAGIC INSTALL
MENU appears
2. Click NEXT install sound driver
40
Page 43
3. Click Finish and Restart Computer 4. Avance Audio Rack table can play CD, WAV,
MID, MP3, AVI, MPG format file
5. Sound Effect select and KaraOK Mode
Function
6. Manual Sound Effect Setting
NOTE: MAGIC INSTALL will auto detect file path:
X:\CODEC\ALC\SETUP.EXE (for WINDOWS 95/98/98SE/ME/NT4.0/2000)
4-5 LAN INSTALL VIA VT6105 Rhine III LAN Controller Driver
(815EDAL/815EPDAL only)
The VIA VT6105 Rhine III Fast Ethernet Adapter Driver path is X:\VIA6105
1. Click LAN when Magic Install Menu appear 2. Setup VIA VT6105 Rhine III Fast Ethernet
Driver
41
Page 44
3. Driver install Finish , Click Yes and Restart
Computer
4. When windows ask VIA VT6105 Rhine III
Fast Ethernet source disk, Change path to
X:\VIA6105 and click OK, then finish
installation
4-6 PC-HEALTH Winbond Hardware Doctor Monitoring
Software
The path of the file is X:\INTEL815\HW30\SETUP.EXE (Only support WINDOWS 98SE/ME)
In Windows 98 Winbond Hardware Doctor Monitoring Software needs some system files to copy in
Utility that’s why it needs install PC-HEALTH twice to complete setup.
1. Click PC-Health when Magic Install Menu
appears
2. Click Next when Winbond Hardware Doctor
Setup Window appears
3. Click Next to continue installation 4. Select Program Group name or enter a new
group name, click Next, and click Finish after
setup complete
42
Page 45
4-6-1 How To Utilize PC-HEALTH
1.Click Program → Winbond Hardware Doctor
→ Hardware Doctor the Winbond Hardware
Doctor will appears
You can remove the Utility in Control Panel
→ Add/Remove Program icon
2. After executing Winbond Hardware Doctor it
supports system voltage, Fan speed and
CPU/SYSTEM Temperature. Because this is
a On-time Monitoring program therefore the
value will change after it detected, if the value
is over default setting the system will have
warning picture and beeps. This is a System
Voltage status
3. This is a CPU/System Fan Speed and
Temperature status information
4. This is a CPU and System Memory status
information
4-7 MAGIC BIOS Install BIOS Live Update Utility
1. Click Magic BIOS when Magic Install
MENU appears
2. Click Next to install the Magic BIOS in
Destination Folder
43
Page 46
3. After finish Setup you will have a Magic
BIOS icon in your screen
5. When On-line update BIOS the program
will auto-check your BIOS version
4. Double click the Magic BIOS icon you will
have this picture, choose from internet you
can upgrade BIOS On-line
6. Click Next if you need update BIOS, after
upgrade BIOS, the system will clear CMOS
and automatically restart
7. Click Yes if you want to update the BIOS
otherwise choose No to exit
9. When choose From Local Driver to update
BIOS, you must have the correct BIOS file
in your Local Driver
8. When System programming BIOS don’t turn
off power, after finish update BIOS, the
system will clear CMOS and automatically
Restart
10. Choose the correct BIOS file to update BIOS
44
Page 47
4-8 PC-CILLIN Install PC-CILLIN 2002 Anti-virus program
1. Click PC-CILLIN when MAGIC INSTALL
MENU appear
2. (1) Click "Install PC-CILLIN" when PC-
CILLIN 2002 main menu appears, and Click
NEXT when "Install Shield Wizard For PCCILLIN 2002"
(2) Click Open Manual. you can learn PCCILLIN 2002 how to use
3. This is license agreement, select "I Accept
the terms" and Click NEXT
4. Click NEXT and Enter your Customer
Information, Click NEXT or choose Change
to change the path for the file to be stored
5. Click INSTALL, Start to install the software 6. Setup Complete and click FINISH
45
Page 48
7. After PC-CILLIN 2002 complete, Please
register your information and get LICENSE
KEY from TREND MICRO web site, enter
your license key and click FINISH
8. finish register process, we recommend select
update item ro download newest engine code
and virus code
Note : Please install ACROBAT READER, Before you read PC-CILLIN 2002 User
Manual, the path at X:\acrobat\ar500eng.exe
4-9 HOW TO DISABLE ON-BOARD SOUND
Enter BIOS SETUP choose INTEGRATE PERIPHERALS choose ON-CHIP DEVICE
FUNCTION choose AC97 AUDIO
Disable on-board sound function by press PAGE DOWN KEY to Disable
4-10 HOW TO UPDATE BIOS
Before update BIOS please choose Disabled in “Flash Part Write Protect” item on
“Miscellaneous Control” in BIOS Setup, please refer page 35
Method 1. Use “Magic BIOS” update BIOS in Windows 98 (refer page 43)
Method 2. In DOS Mode
STEP 1. Prepare a boot disc. (you may make one by click START click RUN type SYS A: click
OK)
STEP 2. Copy utility program to your boot disc. You may copy from DRIVER CD
X:\FLASH\AWDFLASH.EXE or download from our web site.
STEP 3. Copy latest BIOS for 815EDA/815EDAL/815EPDA/815EPDAL from our web site to your
boot disc.
STEP 4. Insert your boot disc into A:,
start the computer, type “Awdflash A:\815EDAxxx.BIN /SN /PY /CC /R”
815EDAxxx.BIN is the file name of latest BIOS it can be 815EDAA3.BIN or
815EDAB2.BIN
SN means don’t save existing BIOS data
PY means renew existing BIOS data
CC means clear existing CMOS data
R means restart computer
STEP 5. Push ENTER and the BIOS will be updated, computer will be restarted automatically
46
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.