Jet Tools GH-2280ZX User Manual
22" x 80" ZX Series
10HP Large Spindle Bore Lathe
The JET® ZX Series Large Spindle Bore Lathe line-up has been expanded with the
introduction of the GH-2280ZX. This new 10HP ZX Series lathe boasts a 22" swing
over bed and comes standard with a 10" 3-jaw chuck with top reversing jaws and a
12" 4-jaw chuck. The 22" ZX Series Large Spindle Bore Lathe comes equipped with
a 3-1/8" bore spindle supported by two tapered bearings and one ball bearing and a
universal gear box with pitch threads in inches, metric, diametral and module. The
universal gear box is dial controlled eliminating the need for changing end gears. The
GH-2280ZX also comes standard with a follow rest and large capacity steady rest.
STOCK NO. 900479
10M 09/06
©2006 WMH TOOL GROUP, Inc. All Rights Reserved.
jettools.com
Universal
Gear Box
22" x 80" ZX SERIES 10HP LARGE SPINDLE BORE LATHE
Steady Rest
Standard
Equipment
3-1/8"
Bore Spindle
Heavy-Duty
One Piece
Cast Iron Base
Foot
Break
22" x 80" ZX SERIES
10HP LARGE SPINDLE BORE LATHE
■ Uniquely designed exclusively by JET
■ ISO 9001 certified manufacturer
■ 3-1/8" bore spindle is supported by two tapered
and one ball bearing
■ Chrome molybdenum headstock gears are hardened,
ground, and shaved
■ Universal gear box allows inch, metric, diametral,
and module pitch threads, no change gears required
■ Carriage features one-shot lubrication and Turcite-B
on bed sliding surfaces
■ T-slotted compound slide featuring a four-way tool post
■ One-piece cast iron base absorbs vibration allowing heavier
cuts
■ High quality ANSI Class 50 wear-resistant cast iron
bed ways are hardened and ground
■ Removable gap allows up to 23-5/8" diameter work
on 16", 27-1/2" on 18"
■ Five position automatic carriage stop increases productivity
■ Attractive chrome control levers, dials, and knobs
■ Tolerance test certificate included
■ Also available with collet closer, taper attachments,
and digital readouts
STOCK NUMBER 321980
Model
Swing Over Bed (in.)
Swing Over Cross Slide (in.)
Swing Through Gap (in.)
Length of Gap (in.)
Distance Between Centers (in.)
Spindle Bore (in.)
Spindle Mount
Spindle Taper (with sleeve)
Number of Spindle Speeds
Range of Spindle Speeds (RPM)
Number of Longitudinal and Cross Feeds
Range of Longitudinal Feeds (in./rev.)
Range of Cross Feeds (in./rev.)
Number of Inch Threads
Range of Inch Threads
Number of Metric Threads
Range of Metric Threads (mm)
Maximum Tool Size (in.)
Maximum Compound Slide Travel (in.)
Maximum Cross Slide Travel (in.)
Maximum Carriage Travel (in.)
Tailstock Spindle Travel (in.)
Tailstock Taper
Follow Rest Capacity (in.)
Steady Rest Capacity (in.)
Width of Bed (in.)
Overall Dimensions (in./L x W x H)
Motor
Net Weight (lbs.)
10HP, 230/460V, 3Ph, Prewired 230V
GH-2280ZX
22
13
29-1/2
12-1/4
80
3-1/8
D1-8
MT-7(MT-5)
12
25-1,800
122
.0015 – .0913
.0006 – .0365
61
1-5/8 – 72
24
.05 – 20
1 x 1
5-1/8
10
75
5
MT-5
1/2 - 3-1/2
3/8 – 7
13-3/8
136-1/8 x 40 x 48-7/8
7400
jettools.com
Loading...