OWNER'S MANUAL
DC-1200A Dust Collector
JET EQUIPMENT & TOOLS, INC. P.O. BOX 1349 Phone:253-351-6000
A WMH Company Auburn, WA 98071-1349 Fax: 1-800-274-6840
www.jettools.com e-mail jet@jettools.com M-708634 02/02
This manual has been prepared for the owner and operators of JET’S DC-1200A. Its purpose, aside from
machine operation, is to promote safety through the use of accepted correct operating and maintenance
procedures. Completely read the safety and maintenance instructions before operating or servicing the
machine. To obtain maximum life and efficiency from your Dust Collector, and to aid in using the
machine safely, read this manual thoroughly and follow instructions carefully.
Warranty & Service
The JET Group warrants every product it sells. If one of our tools needs service or repair, one of our
Authorized Repair Stations located throughout the United States can give you quick service.
In most cases, any one of these JET Group Repair Stations can authorize warranty repair, assist you in
obtaining parts, or perform routine maintenance and major repair on your JET, Performax or Powermatic
tools.
For the name of an Authorized Repair Station in your area, please call 1-800-274-6848.
More Information
Remember, the JET Group is consistently adding new products to the line. For complete, up-to-date
product information, check with your local JET Group distributor.
JET Group Warranty
The JET Group (including Performax and Powermatic brands) makes every effort to assure that its
products meet high quality and durability standards and warrants to the original retail
consumer/purchaser of our products that each product be free from defects in materials and
workmanship as follow: 1 YEAR LIMITED WARRANTY ON ALL PRODUCTS UNLESS SPECIFIED
OTHERWISE. This Warranty does not apply to defects due directly or indirectly to misuse, abuse,
negligence or accidents, normal wear-and-tear, repair or alterations outside our facilities, or to a lack of
maintenance.
THE JET GROUP LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD SPECIFIED ABOVE, FROM
THE DATE THE PRODUCT WAS PURCHASED AT RETAIL. EXCEPT AS STATED HEREIN, ANY
IMPLIED WARRANTIES OR MERCHANTIBILITY AND FITNESS ARE EXCLUDED. SOME STATES
DO NOT ALLOW LIMITATIONS ON HOW LONG THE IMPLIED WARRANTY LASTS, SO THE ABOVE
LIMITATION MAY NOT APPLY TO YOU. THE JET GROUP SHALL IN NO EVENT BE LIABLE FOR
DEATH, INJURIES TO PERSONS OR PROPERTY, OR FOR INCIDENTAL, CONTINGENT, SPECIAL,
OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF OUR PRODUCTS. SOME STATES
DO NOT ALLOW THE EXLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
To take advantage of this warranty, the product or part must be returned for examination, postage
prepaid, to an Authorized Repair Station designated by our office. Proof of purchase date and an
explanation of the complaint must accompany the merchandise. If our inspection discloses a defect, we
will either repair or replace the product, or refund the purchase price if we cannot readily and quickly
provide a repair or replacement, if you are willing to accept a refund. We will return repaired product or
replacement at JET’S expense, but if it is determined there is no defect, or that the defect resulted from
causes not within the scope of JET’S warranty, then the user must bear the cost of storing and returning
the product. This warranty gives you specific legal rights; you may also have other rights which vary
from state to state.
The JET Group sells through distributors only. Members of the JET Group reserve the right to effect at
any time, without prior notice, those alterations to parts, fittings, and accessory equipment which they
may deem necessary for any reason whatsoever.
2
WARNING
1. Read and understand the entire contents of this manual before attempting assembly or
operation. Do not use this machine until proper training and knowledge has been obtained.
2. Do not leave Dust Collector when plugged in. Unplug from outlet when not in use and before
servicing.
3. Do not use outdoors or on wet surfaces.
4. Do not allow to be used as a toy. Close attention is necessary when used near children.
5. Use only as described in this manual. Use only manufacturer’s recommended attachments.
6. Do not use with damaged cord or plug. If Dust Collector is not working as it should, has been
dropped, damaged, left outdoor, or dropped in water, return it to a service center.
7. Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp
edges or corners. Do not run Dust Collector over cord. Keep cord away from heated surfaces.
8. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
9. Do not handle plug or Dust Collector with wet hands.
10. Do not put any objects into the openings. Do not use with any opening blocked; keep free of dust,
lint, hair, and anything that may reduce air flow.
11. Keep hair, loose clothing, fingers, and all parts of body away from opening and moving parts.
12. Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
13. Do not use without dust bag and/or filters in place.
14. Turn off all controls before unplugging.
15. Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they
may be present.
16. Do not operate without hose connected to the inlet ports or covered by an inlet cap. Hazardous
moving parts inside. Unplug machine before removing inlet port, inlet cap, hose, or inlet guard.
17. Use the inlet caps to cover the inlet port openings that are not connected to hoses.
18. Some dust created by power sanding, sawing, grinding, drilling and other construction activities
contains chemicals known to cause cancer, birth defects or other reproductive harm. Some
examples of these chemicals are:
• Lead from lead based paint
• Crystalline silica from bricks and cement andother masonryproducts, and
• Arsenic and chromium from chemically-treated lumber.
19. Your risk from those exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well ventilated area, and work with approved
safety equipment, such as those dust masks that are specifically designed to filter out microscopic
particles
20. Do not operate tool while under the influence of drugs, alcohol or any medication.
21. Make sure the extension cord is in good condition. When using an extension cord, be sure to use
one heavy enough to carry the current your product will draw. An undersize cord will cause a drop
in the line voltage resulting in loss of power and overheating. The table below shows the correct
size to use depending on cord length and nameplate ampere rating. If in doubt, use the next
heavier gauge. The smaller gauge number, the heavier the cord.
22. Do not use dust collector for anything except wood dust. Materials such as liquids, metal shavings,
metal dust, screws, glass, plastic or rock can cause sparks and/or damage when coming into
contact with any part of the dust collector.
23. Ground your dust collector along all plastic componets. The connection of bare 12 gauge copper
wire on all plastic hoses, fittings and blast gates to all machines will help reduce the occurrence of
static build up and discharge.
SAVE THESE INSTRUCTIONS
3
Specifications: DC-1200A-1 DC-1200A-3
Stock Number....................................................708634 ............................................................... 708635
Blower Wheel Diameter..................................... 12".............................................................................12”
Sound Rating at 3 feet....................................... 80-85 db...........................................................80-85 db
HoseDiameter...................................................4" & 6” ................................................................. 4” & 6”
Air Flow (CFM)..................................................1,200..................................................................... 1,200
Velocity at 4” (FPM)........................................... 13,745................................................................. 13,745
Static Pressure (inch of water)........................... 11.44.................................................................... . 11.44
Bag Diameter .................................................... 20".............................................................................20"
Bag Length........................................................ 31-1/2”.................................................................31-1/2”
Collector Bag Capacity (cu. ft.).......................... 5.6.............................................................................5.6
Overall Dimensions 30 Micron..........................37"L x 28"W x 79"H.........................37"L x 28"W x 79"H
Overall Dimensions 5Micron............................ 37"L x 28"W x 96"H.........................37"L x 28"W x 96"H
Motor (TEFC) .................................................... 2 HP, 1Ph 230V only....................2 HP, 3Ph 230V/460V
.......................................................................... ...............................................................Prewired 230V
Net Weight (approx.) .........................................108 lbs................................................................108 lbs.
Table of Contents Page
Warranty .................................................................................................................................................2
Warnings ....................................................................................................................... ..........................3
Specifications..........................................................................................................................................4
Table of Contents....................................................................................................................................4
Unpacking DC-1200A..............................................................................................................................5
Contents of Shipping Carton....................................................................................................................5
Tools Required for Assembly...................................................................................................................5
Assembly..............................................................................................................................................6-8
Electrical Connections .............................................................................................................................8
Turning the Machine On & Off.................................................................................................................8
Maintenance............................................................................................................................................ 9
Cleaning the Filter Bag......................................................................................................................9
Removing the Collector Bag..............................................................................................................9
Motor.................................................................................................................................................9
Connecting the Dust collector to a Machine .............................................................................................9
Grounding the Dust Collection System.....................................................................................................9
Parts Breakdown and Parts List........................................................................................................10-11
Wiring Diagrams....................................................................................................................................12
The specifications in this manual are given as general information and are not binding. JET Equipment
& Tools reserves the right to effect, at any time and without prior notice, changes or alterations to parts,
fittings, and accessory equipment deemed necessary for any reason whatsoever.
4
WARNING
Read and understand the entire contents of
this manual before attempting assembly or
operation of the dust collector!
Failure to comply may cause serious injury!
Unpacking
1. Finish removing all contents from the
shipping carton.
2. Report any damage to your distributor.
3. Do not discard any shipping material until
after the dust collector has been assembled
and is running properly.
Contents of the Shipping Carton
1 Bag Hanger
1Base
1 Plastic Cover
1 Hanger Bracket
1Hose
1 Owner's Manual
1 Warranty Card
1 Motor/Fan Assembly
1 CollectorBag
1 FilterBag
2HoseClamps
1 Retainer Strap
4Casters
1 Inlet Cover & Hose Inlet
3 Support Legs
1 Bag of Assembly Hardware
16. M8 x 16 Hex Cap Bolts
34. M8 Flat Washers
8. M6 x 12 Pan Head Flange Bolts
10. M8 Hex Nuts
Tools Required for Assembly
2. 1/2” or 13mm Wrenches or sockets
1. 9/16” or 14mm Wrench or socket
1. #2 Cross Point Screw Driver
5
Assembly
1. Install four casters to the under side of the
base as pictured in Fig. 1. Thread the hex
nut (B, Fig. 1) onto the caster shaft. Then
slide the lock washer (A, Fig. 1) over the
caster shaft. Thread the caster shaft into
the threaded hole on the underside of the
base, turn until snug. Tighten the nut (B,
Fig. 1) against the base with a 9/16” or
14mm wrench. This will give the caster
proper clearance.
2. Place the base with casters on the ground.
Attach the motor and fan assembly (A, Fig.
2) to the base using four M8 x 16 hex cap
bolts, four M8 flat washers (B, Fig. 2), and a
1/2" or 13mm wrench.
WARNING
The dust collector must be disconnected
from the power source during assembly.
Failure to comply may result in serious
injury!
3. Attach inlet guard (A, Fig. 3) to fan housing
using eight M5 x 12 pan head screws (B,
Fig. 3). Press the inlet ports onto the inlet
guard until it snaps into place.
WARNING
To reduce the risk of injury from moving
parts, always keep inlet ports covered with
the caps provided, if they are not
connected to a flexible hose. Failure to
comply may result in serious injury!
6
4. Attach three support brackets (A, Fig. 4) to
the base using six M8 x 16 hex cap bolts
and six M8 flat washers (B, Fig. 4). Hand
tighten only at this time.
5. Install the housing (A, Fig. 5) to two support
brackets using four M8 x 16 hex cap bolts,
eight M8 flat washers, and four M8 hex nuts
(B, Fig.5). Be sure hose opening faces fan
housing. Before attaching third support
bracket place the hanger bracket (C, Fig.5)
between the support bracket and the
housing. Tighten all nuts and bolts at this
time with a 1/2" or 13mm wrench.
6. Attach the hose (A, Fig. 6) between the fan
housing and the collector housing with two
clamps (B, Fig. 6). Tighten the clamps to
secure the hose.
7
7. Slide the bag hanger hook (A, Fig. 7)
through the top loop of the filter bag. Insert
the hanger into the hanger bracket. Thread
the retainer strap (B, Fig. 7) through the
loops on the filter bag (C, Fig.7), and fasten
to the collector housing. The retainer strap
should be tight enough to provide a good
seal.
8. Insert the ring (A, Fig. 8) of the collector bag
into the bottom of the housing at an angle.
Pull down on the bag to make sure it “seats”
in the housing.
Electrical Connections
WARNING
All electrical connections must be done by a
qualified electrician. A ll adjustments or
repairs must be done with the dust collector
disconnected from the power source,
unplugged. Failure to comply may result in
serious injury!
The DC-1200A-1 dust collector is rated at 230V
Only. The DC-1200A-3 is rated at 3 Phase
230V/460V, Prewired 230V.
If you want to run the DC-1200A-3 on 460V refer
to the wiring diagram found on the inside of the
switch box cover.
Use a plug and outlet rated at least 20 amps.
The circuit for the machine should also be
protected by at least a 20 amp circuit breaker or
fuse. Keep in mind that a curcuit being used by
other machines, tools, lights, heaters, etc. at the
same time will add to the electrical load. A
dedicated curcuit to the dust collector will give
you the best results since dust collectors are
generally used at the same time other tools are
running.
Before hooking up to the power source, make
sure that the switch is in the off position.
Turning the Machine On & Off
Before hooking up to the power source, make
sure that the switch is in the off position.
The dust collector can be turned on by pressing
the start button found on the motor. Press the
stop button to turn off the dust collector.
8
Maintenance
WARNING
Never perform maintenace on this machine
before turning switch off and removing plug
from power source, unplug.
Failure to comply may cause serious injury!
Cleaning the Filter Bag
CAUTION
Wearing a particle mask/respirator for
protection against fine dust particles during
cleaning is highly recommended.
5. Turn the bag outside in and insert into the
housing.
Use the proper type hose to connect the dust
collector to the machine being operated. Dryer
vent hose is not acceptable for this purpose.
Contact your nearest JET distributor for the full
line of JET Dust Collector Hoses and
Accessories. Customize your installation and
obtain maximum performance with JET's dust
hoods, hoses, clamps, fittings, and blast gates.
Accessories.
Motor
During first use and after cleaning, the filter bag
may allow some dust to escape. This is normal
and will stop after a short period of time.
Clean both the filter and collector bags
frequently to keep the collector's performance at
its optimum. To clean:
1. Disconnect the machine from the power
source.
2. Unhook the filter bag from the hanger and
shake the bag so that the majority of the
dust falls into the collector bag.
3. Loosen the retaining strap, and remove the
filter bag from the housing.
4. Turn the bag inside out and clean.
5. Turn the bag outside in and re-attach to the
housing using the retainer strap to secure.
Removing the Collector Bag
1. Disconnect the machine from the power
source, unplug.
2. Remove the collector bag by pushing the
ring of the collector bag upwardsand pulling
the bag out at an angle.
3. Empty the contents into an appropriate
container.
Make frequent inspections of the motor fan and
blow out (with low pressure air hose) or vacuum
any accumulation of foreign material in order to
maintain normal motor ventilation.
Connecting the Dust collector to a
Machine
Use the proper type hose to connect the dust
collector to the machine being operated. Dryer
vent hose is not acceptable for this purpose.
Contact your nearest JET distributor for the full
line of JET Dust Collector Hoses and
Accessories. Customize your installation and
obtain maximum performance with JET's dust
hoods, hoses, clamps, fittings, and blast gates.
You can also purchase the JET “Dust Collection
Basics Video” stock # JW1050V through your
JET Distributor
Grounding the Dust Collection System
The dust collection system includes the dust
collector and the hose, or duct work you use to
connect the tools. The dust collector is grounded
though the ground wire in the cord. The hose or
duct work you use to connect the tool to the dust
collector must also be grounded. To assist in
grounding your system you can purchase the JET
“Dust Collector Grounding Kit” stock # JW1053,
and also the JET “Dust Collection Basics Video”
stock # JW1050V through JET Distributors.
4. Turn the bag inside out and clean.
9
Parts Breakdown
10
Parts List for the DC-1200A
Index Part
No. No. Description Size Qty.
1.......... 411035W ..................... Im peller Housing.................................... ...............................................1
2.......... 411026W ..................... Motor Bracket........................................ ...............................................1
3.......... 998621......................... Strain Relief........................................... ...............................................1
4.......... MA411003.................... Motor.....................................................2 HP, 1Ph...............................1
............ MA411003-3 ................Motor..................................................... 2 HP, 3 Ph ..............................1
............ DC1100-50W ............... Motor Fan Cover (not shown)................ ...............................................1
............ MF411012.................... Motor Fan (not shown)........................... ...............................................1
............ CA003030....................Running Capacitor (not shown)..............30MFD, 300V..........................1
............ CA020010....................Starting Capacitor (not shown)...............200MFD, 125V........................1
5.......... 411051......................... Switch Box ............................................ ...............................................1
6.......... 411053......................... Switch Plate........................................... ...............................................1
7.......... 994542......................... Switch....................................................1 Ph........................................1
............ DC1900-23B ................ Switch....................................................3 Ph........................................1
8.......... IC420002 ..................... Power Cord............................................ ...............................................1
9.......... 420051......................... Motor Packing....................................... ...............................................1
10........AB411059....................Impeller.................................................12” ..........................................1
11........411036W ..................... Inlet Guard............................................ ...............................................1
12........427028.........................Inlet Port................................................2 @ 4”.....................................1
13........420203.........................Inlet Cap................................................ ...............................................2
14........430034.........................Inlet Flange Packing.............................. ...............................................1
15........411041W ..................... Base...................................................... ...............................................1
16........402036.........................Pivoting Caster...................................... ...............................................4
17........420012W ..................... Housing................................................. ...............................................1
18........402004W ..................... Support.................................................. ...............................................3
19........523011W ..................... Hanger Bracket...................................... ...............................................1
20........411009.........................Hose......................................................5”x65(CM)...............................1
21........420010.........................Ring Clamp ...........................................5”............................................2
22........402040.........................Hanger ..................................................30 Micron Bag Hanger ............1
............ AB430039 .................... Hanger ..................................................5 Micron Bag Hanger ..............1
24........708698.........................Filter Bag...............................................30 Micron Bag .........................1
............ 708702......................... Filter Bag...............................................5 Micon Bag............................1
25........AB410012....................Retainer Strap....................................... ...............................................1
26........708699A ...................... Collection Bag....................................... ...............................................1
27........450038.........................Bracket Cap........................................... ...............................................1
31........ST039304.................... Tapping Screw.......................................M3.5x12(AB)...........................6
32........KS050525....................Key........................................................5x5x25....................................1
34........TS-1540061.................Nut ........................................................M8 ........................................10
35........TS-0561031.................Nut ........................................................3/8”-16UNC.............................4
36........TS-1490031................. Hex Head Bolt .......................................M8x20...........................................1
37........TS-1490011.................Hex Head Bolt.......................................M8x12.....................................4
38........TS-1490021.................Hex Head Bolt.......................................M8x16...................................16
39........TS-1490041.................Hex Head Bolt.......................................M8x25.....................................4
40........TS-1554041.................Pan Head Bolt W/Fl ange .......................M6x12 .....................................2
41........TS-0680031.................Flat Washer...........................................M8 ..........................................1
42........TS-1554041.................Pan Head Bolt W/Fl ange .......................M6x12 .....................................8
43........TS-0680031.................Flat Washer...........................................M8 ........................................34
44........TS-0720081.................Spring Washer.......................................M8 ..........................................8
45........TS-1551071.................Spring Washer.......................................M10.........................................4
46........ST059304.................... Tapping Screw.......................................M5x12.....................................2
............ DC1200-53................... Grounding Label (not shown)................. ...............................................1
............ DC1200-54................... Direction Label (not shown) ................... ...............................................1
............ DC1200A-NP ............... Name Plate (not shown)........................ ...............................................1
............ DC1100-HP..................Hardware Package(not shown) ............. ...............................................1
............ DC1200A-CS ............... Centrifugal Switch (not shown)............... ...............................................1
............ DC1900-53................... Warning Label (not shown).................... ...............................................1
11
Wiring Diagram For 3 Phase 230V/460V Dust Collector
Wiring Diagram For Single Phase 230V Only Dust Collector
12
Loading...