Page 1
OWNER’S MANUAL
DISHWASHER INSTALLATION AND MAINTENANCE
F14
F16
F18
For operator. Do not discard.
F20
F22
727
737
747
767
Page 2
Welcome to JET-TECH
“Creating
endless
possibilities!”
We have included information to help troubleshoot
problems and facilitate resolving those problems.
General information pertaining to our hi-temp ware
washers will be covered in this
manual.
Specific
information on our current and older models is available
upon request, model by model.
If you find any discrepancy or can’t find certain
information, please contact us. We will be glad to be
of
assistance.
MVP GROUP CORPORATION
JET-TECH SYSTEMS
5659
Royalmount Avenue
Montreal, Quebec H4P
Tel.: 888 -275-4538 (888-ASK-4-JET); 514-737-9701
Fax:
877-452-8832;
E-mail: service@jet-tech.com
2P9
514-737-2792
2
Page 3
Contents
WARRANTY.....................................................4
MACHINES SPECS.........................................5
GENERAL INSTALLATION GUIDELINES........6
CONNECTING YOUR F-14..............................7
CONNECTING YOUR F-16..............................8
CONNECTING YOUR F-18........................9, 10
CONNECTING YOUR F-20............................11
CONNECTING YOUR F-22......................12, 13
CONNECTING YOUR 727..............................14
CONNECTING YOUR 737..............................15
CONNECTING YOUR 747..............................16
CONNECTING YOUR 767..............................17
CHEMICAL PUMP ADJUSTMENT............18, 19
CONTROL PANELS........................................20
BASICS STEPS TO START............................21
OPERATION.............................................22, 23
F18, BASICS STEPS TO OPERATE...............24
F22, BASICS STEPS TO OPERATE...............25
DRAIN PUMP OPERATION.............................26
PROBLEM ANALYSIS...................27, 28, 29, 30
HELP LINE.......................................................31
3
Page 4
MANUFACTURERS LIMITED WARRANTY
MVP GROUP CORPORATION (Jet-Tech Systems) hereby warrants all new warewashers bearing
the name “JET-TECH” and installed within the continental United States of America or Canada to be
free from defects in material and workmanship, under normal and regular usage and operation, for a
period of one (1) year following the date of original installation (unless specified otherwise) but in
no event can exceed eighteen (18) months from the date of shipment from the factory.
This warranty is valid ONLY for the original owner of the “Jet-Tech” unit and is not transferrable.
If a defect in material(s) or workmanship is detected or found to exist within the above stated
period, MVP Group Corp., at its sole discretion, shall either repair or replace any original
equipment manufacturers part which has proven to fail within the machine, providing that the
equipment has not been altered or tampered with in any manner, has been installed correctly as
per the owner’s manual and maintained and operated in complete accordance with this manual.
The labor cost to repair or replace any part proven to be defective, as per above clause(s), shall be
covered by MVP Group Corp., within the continental United States of America or Canada provided
that prior authorization for this labor was approved by MVP Group Corp., the service work was
performed by an authorized MVP Group Corp., service agency and that this agency installed an
original and genuine Jet-Tech part in the machine. Any repair work performed by a non-authorized
service depot remains the sole responsibility of the user and MVP Group Corp., will not be held
responsible. The installation of any generic part will not be valid and therefore voids this
warranty. All authorized labor coverage shall be limited to regular hourly rates only. Any
supplemental hourly rates or charges, such as weekends, holidays or emergency premiums remain
the responsibility of the user.
MVP Group Corp., (Jet-Tech) hereby states that warranty travel time shall be limited to and
without exception, a round-trip total of two (2) hours OR mileage up to a maximum of one hundred
(100) miles (160 KM) round-trip. Any charges exceeding those stated herein must have prior
authorization by the factory or will be at the customer’s expense.
Exceptions to above warranty are: (A) Damages resulting from shipping, handling or abuse. (B)
Incorrect installation and/or connections. (C) Adjustments or calibration of any parts. (D) Faults due
to lack of regular maintenance or cleaning of any internal part(s). (E) Replacement of any wearable
items such as peristaltic squeeze tubing or gaskets. (F) Excessive lime, mineral, alkali or hard
water conditions (In excess of 6 grain) and (G) Poor results due to use of an incorrect type of
detergent or rinse additive (for non-commercial type applications or products containing chlorine)
and excessive or inadequate water temperature(s) or pressure conditions or incorrect use.
MVP GROUP CORPORATION STATES THAT THERE ARE NO OTHER WARRANTIES,
EXPRESSED OR IMPLIED, THAT ARE NOT SET FORTH HEREIN, MVP GROUP
CORPORATION SHALL ASSUME NO OTHER RESPONSIBILITY, EITHER DIRECT OR NON -
DIRECT OR BE LIABLE FOR ANY OTHER OR ADDITIONAL LOSS OR DAMAGE WHETHER
BEING DIRECT OR CONSEQUENTIAL, AS A RESULT OF ITS EQUIPMENT.
Warranty: One year parts & labor (Continental USA and Canada).
Exceptions: Model “F-14” - 90 days labor & One year parts.
The manufacturer reserves the rights to alter design and specifications without notice.
4
Page 5
5
Page 6
Page 7
Connecting your new F-14
This dishwasher must be installed on a level, rigid, nonflammable surface. Ensure
that the machine is level by installing the feet (shipped in the wash tank of the
machine) and adjusting the leveling. Be sure to provide adequate space for
water, drain and electrical connections. The rear panel must be removed for the
hook ups and must be replaced after the connections are made.
ELECTRICAL SUPPLY
A 115 Volt - 20 Amp circuit breaker is required for this washer. A power-
cord with NEMA 5-20 plug is provided for your convenience.
**WATER SUPPLY**
A 3/4” NPT coupling is required with 30 psi. dynamic pressure. A water
pressure regulator* may be required. The water pressure cannot be less
than 30 psi or exceed 30 psi. If the water pressure exceeds the prescribed
amount, you will get inconsistent washing temperature, premature failure and
thus may void the warranty.
Incoming water temperature must be 140º F (60º C). An easily accessible shut-
off valve is recommended, making installation, service and maintenance easier.
A flexible fill hose is provided to make installation, servicing and
maintenance easier.
Make sure that the water is free from calcium and hard water
deposits. For these situations, an inline water cartridge system is
highly recommended. Build-up of calcium and lime deposits in the
washer may occur and servicing will be required on a more
frequent basis which will not be covered by the warranty.
**DRAIN CONNECTION**
This washer has a gravity type drain. Since this unit is a “Counter-
Type” installation, the flexible drain hose provided should be
connected to the drain outlet elbow at the rear of the unit behind the
rear access panel; and extended through the side opening directly
into a floor drain or
sink (see Figure )
All panels must be replaced on the unit when the
installation is completed.
DO NOT manually fill wash tank with water. The dishwasher will fill
automatically when the power is turned ON.
* - not supplied
** SEE PAGE 6 FOR FURTHER IMPORTANT DETAILS**
7
W
ater
inlet connection
Electrical
Drain
outlet
Page 8
Connecting your new F-16DP
This glasswasher must be installed on a level, rigid, nonflammable
surface. Ensure that the machine is level by installing the feet
(shipped in the wash tank of the machine) and adjusting the leveling.
Be sure to provide adequate space for water, drain and electrical
connections.
**WATER SUPPLY**
A 3/4”NPT fitting is required with 30 psi. dynamic pressure. A water
pressure regulator* may be required. The water pressure cannot be less
than 30 psi or exceed 30 psi. If the water pressure exceeds the
prescribed amount, you will get inconsistent washing temperature,
premature failure and thus may void the warranty.
Incoming water temperature must be 140ºF (60ºC). An easily
accessible shut-off valve is recommended, making installation, service and
maintenance easier. A flexible fill hose is provided to make installation, servicing
and maintenance easier.
Make sure that the water is free from calcium and hard water deposits. For these
situations, an inline water cartridge system is highly recommended. Build-up of
calcium and lime deposits in the washer may occur and servicing will be required
on a more frequent basis which will not be covered by the warranty.
**DRAIN**
·
F-16 DP: This glasswasher is equipped with an automatic drain
pump that will pump the drain water to a maximum height of 36" (0.9
meter). Drain pump equipped machines have a white button on the
control panel beside the green power button.
1" ID flexible drain hose is provided to facilitate maintenance and servicing of the
machine. It is important not to reduce the size of this hose. A 1" check-valve* may be
required. .
ELECTRICAL
A 208-240 volt, 60 Hz, Single Phase circuit is required for this unit. Check the
rating plate on the machine for amp draw. In spite of the fact that the rating
plate shows 208 volts, the unit is designed function properly on 208 volts to
240 volts.
The terminal block is located at the back of the machine. Open the plastic
cover, pass the cable through the cable strain relief and connect the wires to
the L1, L2 & Ground. There should be sufficient cable length to permit the
machine to be pulled out for service. DO NOT turn on the power to the
machine until the water supply & drain lines have been connected. DO NOT
manually fill wash tank. It will fill automatically.
IMPORTANT NOTE
Reasonable access to and around the machine for service must be provided.
Disconnecting of hard plumbing or removal of counter tops or cabinets, etc., for
servicing is not covered by warranty.
* - not supplied
All panels must be replaced on the unit when the installation is completed.
* - not supplied
** SEE PAGE 6 FOR FURTHER IMPORTANT DETAILS**
W
ater
8
In
L1
L2
W
ater
out
Page 9
Connecting your new F-18, F18DP
This dishwasher must be installed on a level, rigid, nonflammable
surface. Ensure that the machine is level by installing the feet
(shipped in the wash tank of the machine) and adjusting the leveling.
Be sure to provide adequate space for water, drain and electrical
connections.
**WATER SUPPLY**
A 3/4” NPT fitting is required with 30
psi. dynamic pressure. A water pressure
regulator* may be required. The water
flow pressure cannot be less than 30 psi
or exceed 30 psi. If the water pressure
exceeds the prescribed amount, you will
get inconsistent washing temperature,
premature failure and thus may void the warranty.
Incoming water temperature must be 140º F (60º
C). An easily accessible shut-off valve is
recommended, making installation, service and
maintenance easier.
A flexible drain hose is provided to make installation, servicing and maintenance
easier. Make sure that the water is free from calcium and hard water deposits. For
these situations, an inline water cartridge system is highly recommended. Build-up of
calcium and lime deposits in the washer may occur and servicing will be required on a
**DRAIN**
·
F-18: This dishwasher has a gravity drain. Maximum height of the floor drain
should not exceed 6" (15cm). A 1.5" ID flexible drain hose is supplied to
facilitate maintenance and servicing of the machine.
·
F-18 DP: This dishwasher is equipped with an automatic drain pump that will
pump the drain water to a maximum height of 36" (0.9 meter). A 1" ID flexible
drain hose is supplied to facilitate maintenance and servicing of the machine. It
is important not to reduce the size of this hose. A 1" check-valve*
more frequent basis which will not be covered by the warranty.
may be required on
drain pump equipped models. Drain pump
equipped machines have a white button on
the control panel beside the green power
button. Conversion from gravity to “DP” is
not possible in the field.
Gravity Drain
* - not supplied
** SEE PAGE 6 FOR FURTHER IMPORTANT DETAILS**
P
umped Drain
9
Page 10
Installation F-18 , continued
ELECTRICAL
A 208-240 volt, 60 Hz, Single Phase circuit is required
for this unit. Check the rating plate on the front of the
machine for the amp draw. In spite of the fact that the
rating plate shows 220 volts, the unit is designed
function properly on 208 volts to 240 volts.
The top & back panels must be removed for the
electrical hook -up. The top panel is secured by two
Phillips head screws. Once the screws are removed,
the panel should be slid to the back and lifted. The
back panel is also held by two screws. Remove them,
pull the bottom away from the machine and lift the
panel.
The terminal block is located inside the back cover. Pass the cable through the cable strain relief and
connect the wires to the terminals L1 (brown wire), L2 (blue wire) & Ground (yellow & green wire). Replace
the top & back panels being careful not to pinch or kink any
wires or hoses. There should be sufficient cable length to
permit the machine to be pulled out for service.
IMPORTANT NOTE
Reasonable access to and around the machine for
service must be provided. Disconnecting of hard
plumbing or removal of counter tops or cabinets, etc., for
servicing is not covered by warranty.
W
G
L2
ater
L1
In
DO NOT fill dishwasher manually with water. The
dishwasher will fill automatically when the power is
turned on.
All panels must be replaced on the unit when the installation is completed.
* - not supplied
10
W
ater
Out
Page 11
Connecting your new F-20
This dishwasher must be installed on a level, rigid, nonflammable surface. Ensure that the
machine is level by installing the feet (shipped in the wash tank of the machine) and adjusting the
leveling. Be sure to provide adequate space for water, drain and electrical connections.
**WATER SUPPLY:**
A 3/4” NPT fitting is required with 30 psi. dynamic pressure. A water
pressure regulator* may be required. The water pressure cannot be less
than 30 psi or exceed 30 psi. If the water pressure exceeds the prescribed
amount, you will get inconsistent washing temperature, premature parts
failure and thus may void the warranty.
Incoming water temperature must be 140º F (60º C). An easily accessible
shut-off valve is recommended, making installation, service and
maintenance easier. A flexible drain hose is provided to make installation,
servicing and maintenance easier.
Make sure that the water is free from calcium and hard water deposits. For these situations, an on-
line water cartridge system is highly recommended. Build-up of calcium and lime deposits in the
washer may occur and servicing will be required on a more frequent basis which will not be
covered by the warranty.
**DRAIN:**
This dishwasher has a gravity drain. Maximum height of the floor drain should not exceed
20" (50cm). A 1.5" ID flexible drain hose is recommended to facilitate maintenance and
servicing of the machine.
ELECTRICAL:
A 208-240 volt, 60 Hz, Single Phase circuit is required for this unit. Check the rating plate on the
machine for amp draw. In spite of the fact that the rating plate shows 208 volts, the unit is designed
function properly on 208 volts to 240 volts.
The top & back panels must be removed for the electrical hook
-up. The top panel is secured by Phillips head screws. Once the
screws removed, the panel should be slid to the back and lifted.
The back panel is also held by Phillips head screws. Remove
them, pull the bottom away from the machine and lift the panel.
The terminal block is located at the top of the machine and can
be accessed by removing the top and back panel. Pass the
cable through the cable strain relief at the back and connect
the wires to the terminals L1 (brown wire), L2 (blue wire) &
Ground (yellow & green wire). There should be sufficient cable
length to permit the machine to be pulled out for service.
DO NOT manually fill wash tank with water. The dishwasher will fill automatically when the power is turned ON.
IMPORTANT NOTE
Reasonable access to and around the machine for service must be provided.
Disconnecting of hard plumbing or removal of counter tops or cabinets, etc., for servicing
is not covered by warranty.
All panels must be replaced on the unit when the installation is completed.
* - not supplied
** SEE PAGE 6 FOR FURTHER IMPORTANT DETAILS**
11
Page 12
Connecting your new F-22
This dishwasher must be installed on a level, rigid, nonflammable surface. Ensure that the
machine is level by installing the feet (shipped in the wash tank of the machine) and adjusting the
leveling. Be sure to provide adequate space for water,
drain and electrical connections.
**WATER SUPPLY:**
A 3/4” NPT fitting is required with 30 psi. dynamic
pressure. A water pressure regulator* may be
required. The water flow pressure cannot be less than
30 psi or exceed 30 psi. If the water pressure exceeds
the prescribed amount, you will get inconsistent
washing temperature, premature parts failure and
thus may void the warranty.
Incoming water temperature must be 140º F (60º C). An easily accessible shut-off valve is
recommended, making installation, service and maintenance easier.
A flexible drain hose is provided to make installation, servicing and
maintenance easier.
Make sure that the water is free from calcium and hard water deposits. For
these situations, an inline water cartridge system is highly recommended.
Build-up of calcium and lime deposits in the washer may occur and servicing
will be required on a more frequent basis which will not be covered by the
warranty.
**DRAIN:**
This dishwasher has a gravity drain. Maximum height of the drain should not exceed 20" (50cm).
A 1.5" ID flexible drain hose* is recommended to facilitate maintenance and servicing of the
machine.
ELECTRICAL:
A 208-240 volt, 60 Hz, Single Phase or Three Phase circuit is required for this unit.
Check the rating plate on the machine for amp draw and phase. In spite of the fact
that the rating plate shows 208 volts, the unit is designed function properly from 208
volts to 240 volts.
The terminal block is located in the control box on the side of the unit. The
faceplate of the control panel pulls out, exposing the terminal block, after the
screws are removed. Pass the cable through the cable strain relief at the back and
connect the wires to the terminals L1 (brown wire), L2 (blue wire), L3 (black wire) &
Ground (yellow & green wire). There should be sufficient cable length to permit the
machine to be pulled out for service.
DO NOT manually fill wash tank with water. The dishwasher will fill automatically when the power is turned ON.
IMPORTANT NOTE
Reasonable access to and around the machine for service must be provided.
Disconnecting of hard plumbing or removal of counter tops or cabinets, etc., for servicing
is not covered by warranty.
All panels must be on the unit when the installation is finished.
* - not supplied
** SEE PAGE 6 FOR FURTHER IMPORTANT DETAILS*
12
Page 13
F
-22 Dish Table configuration
The F-22 is
design to
received
standard
size dish-
tabling
Below
configurations
with the F
If the soiled
the right
side), the
adjusted down to allocate room
for the sink.
If
you
installation, change the brack
that
to the
.
you
can see the
-22.
(sink) section is on
side
(control
control
need to do a
guides
left
the trays from the front
side
different
that can be done
panel
panel can be
corner
et
.
13
Page 14
Connecting your new 727
This dishwasher must be installed on a level, rigid, nonflammable surface. Ensure that the
machine is level by installing the feet (shipped in the wash tank of the machine) and adjusting the
leveling. Be sure to provide adequate space for water, drain and electrical connections.
**WATER SUPPLY**
A 3/4” NPT fitting is required with 30 psi. dynamic pressure. A
water pressure regulator* may be required. The water flow
pressure cannot be less than 30 psi or exceed 30 psi. If the water
pressure exceeds the prescribed amount, you will get inconsistent
washing temperature, premature failure and thus may void the
warranty. Incoming water temperature must be 140º F (60º C). An
easily accessible shut-off valve is recommended, making
installation, service and maintenance easier. This type hose is
standard for most warewashing machines. Fittings should be
available from your local hardware or plumbing supply house.
Flexible hoses must be used to make installation, servicing and
maintenance easier.
Make sure that the water is free from calcium and hard water deposits. For these situations, an on-
line water cartridge system is highly recommended. Build-up of calcium and lime deposits in the
washer may occur and servicing will be required on a more frequent basis which will not be
covered by the warranty.
**DRAIN**
This dishwasher is equipped with an automatic drain pump that will pump the drain water to a
maximum height of 36" (0.9 meter). A 1" ID flexible drain hose is recommended to facilitate
maintenance and servicing of the machine. It is important not to reduce the size of this hose.
There should be sufficient hose length to permit the
machine to be pulled out for service.
Electrical
Water In
ELECTRICAL
A 208-240 volt, 60 Hz, Single Phase circuit is required for
this unit. Check the rating plate on the machine for amp
draw. Despite of the fact that the rating plate shows 208
volts, the unit is designed function properly on 208 volts
to 240 volts.
The terminal block is located at the back of the unit.
Open the cover and connect the wires to the terminals
L1 , L2 & Ground. There should be sufficient cable length to permit the machine to be pulled out
for service. DO NOT TURN ON THE POWER TO THE MACHINE UNTIL THE WATER SUPPLY &
DRAIN LINES HAVE BEEN CONNECTED.
IMPORTANT NOTE
Reasonable access to and around the machine for service must be provided. Disconnecting of
hard plumbing or removal of counter tops or cabinets, etc., for servicing is not covered by warranty.
* - not supplied
All panels must be on the unit when the installation is finished.
** SEE PAGE 6 FOR FURTHER IMPORTANT DETAILS**
14
Water Out
Page 15
Connecting your new 737
This dishwasher must be installed on a level, rigid, nonflammable surface.
Ensure that the machine is level by installing the feet (shipped in the wash
tank of the machine) and adjusting the leveling. Be sure to provide
adequate space for water, drain and electrical connections.
**WATER SUPPLY**
A 3/4” NPT fitting is required with 30 psi. dynamic pressure. A water
pressure regulator* may be required. The water flow pressure cannot be
less
than 30 psi or exceed 30 psi. If the water pressure exceeds the prescribed amount, you will get inconsistent
washing temperature, premature failure and thus may void the warranty.
Incoming water temperature must be 140º F (60º C). An easily accessible shut-off valve is recommended,
making installation, service and maintenance easier. This type hose is standard for most warewashing
machines. Fittings should be available from your local hardware or plumbing supply house.
Flexible hoses must be used to make installation, servicing and maintenance easier.
Ensure that the water is free from calcium and hard water deposits. For these situations, an inline water
cartridge system is highly recommended. Build-up of calcium and lime deposits in the washer may occur and
servicing will be required on a more frequent basis which will not be covered by the warranty.
**DRAIN**
This dishwasher is equipped with an automatic drain pump that will pump the drain
water to a maximum height of 36" (0.9 meter). A 1" ID flexible drain hose is
recommended to facilitate maintenance and servicing of the machine. It is important
not to reduce the size of this hose. A 1" check-valve* may be required.
ELECTRICAL
A 208-240 volt, 60 Hz, Single Phase circuit is required for this unit. Check the
rating plate on the machine for amp draw. In spite of the fact that the rating plate
shows 208 volts, the unit is designed function properly on 208 volts to 240 volts.
There should be sufficient cable length to permit the machine to be pulled out for
service.
The top & back panels must be removed for the electrical hook -up. The top panel
is secured by Phillips head screws. Once the screws removed, the panel should be
slid to the back and lifted. The back panel is held by 6 screws. Remove them,
pull the top away from the machine and lift the panel.
The terminal block is located at the back of the machine.
Pass the cable through the cable strain relief at the back and
connect the wires to the terminals L1 (brown wire), L2 (blue
wire) & Ground (yellow & green wire). There should be
sufficient cable length to permit the machine to be pulled out
for service. DO NOT TURN ON THE POWER TO THE
MACHINE UNTIL THE WATER SUPPLY & DRAIN LINES
HAVE BEEN CONNECTED.
IMPORTANT NOTE
Reasonable access to and around the machine for service
must be provided. Disconnecting of hard plumbing or
removal of counter tops or cabinets, etc., for servicing is not
covered by warranty.
* - not supplied
All panels must be on the unit when the installation is finished.
** SEE PAGE 6 FOR FURTHER IMPORTANT DETAILS**
W
G
L2
ater
L1
In
W
ater
Out
15
Page 16
Connecting your new 747
This dishwasher must be installed on a level, rigid, nonflammable surface. Ensure that the
machine is level by installing the feet (shipped in the wash tank of the machine) and adjusting the
leveling. Be sure to provide adequate space for water, drain and electrical connections.
**WATER SUPPLY**:
A 3/4” NPT fitting is required with 30 psi. dynamic pressure. A water pressure regulator* may be
required. The water flow pressure cannot be less than 30 psi or exceed 30 psi. If the water pressure
exceeds the prescribed amount, you will get inconsistent washing temperature, premature parts
failure and thus may void the warranty.
Incoming water temperature must be 140º F (60º C). An easily accessible shut-off
valve is recommended, making installation, service and maintenance easier. This
type hose is standard for most warewashing machines. Fittings should be available
from your local hardware or plumbing supply house.
Flexible hoses must be used to make installation, servicing and maintenance
easier.
Make sure that the water is free from calcium and hard
water deposits. For these situations, an inline water
cartridge system is highly recommended. Build-up of calcium and lime
deposits in the washer may occur and servicing will be required on a more
frequent basis which will not be covered by the warranty.
**DRAIN**:
This dishwasher has a gravity drain. Maximum height of the drain should
not exceed 20" (50cm). A 1.5" ID flexible drain hose is recommended to
facilitate maintenance and servicing of the machine.
ELECTRICAL:
A 208-240 volt, 60 Hz, Single Phase or Three Phase circuit is
required for this unit. Check the rating plate on the machine for
amp draw. Pump rotation must be verified on 3 phase units at time
of install. In spite of the fact that the rating plate shows 208 volts, the
unit is designed function properly from 208 volts to 240 volts.
The bottom cover (under the controls) is snapped in to position and
should be removed. The terminal block is located in the base of the
unit, on the left side.
Pass the cable through the cable strain relief at the back and connect
the wires to the terminals L1 (brown wire), L2 (blue wire), L3 (black wire)
& Ground (yellow & green wire). There should be sufficient cable length
to permit the machine to be pulled out for service.
DO NOT manually fill wash tank with water. The dishwasher will fill
automatically when the power is turned ON.
IMPORTANT NOTE
Reasonable access to and around the machine for service must be provided.
Disconnecting of hard plumbing or removal of counter tops or cabinets, etc., for servicing
is not covered by warranty.
Verify rotation of the pumps for three phase unit.
All panels must be replaced on the unit when the installation is completed.
* - not supplied
** SEE PAGE 6 FOR FURTHER IMPORTANT DETAILS**
16
Page 17
Connecting your new 767
This dishwasher must be installed on a level, rigid, nonflammable surface. Ensure that the
machine is level by installing the feet (shipped in the wash tank of the machine) and adjusting the
leveling. Be sure to provide adequate space for water, drain and electrical connections.
**WATER SUPPLY:**
A 3/4” NPT fitting is required with 30 psi. dynamic pressure. A water pressure regulator* may be
required. The water flow pressure cannot be less than 30 psi or exceed 30 psi. If the water pressure
exceeds the prescribed amount, you will get inconsistent washing temperature, premature parts
failure and thus may void the warranty.
Incoming water temperature must be 140º F (60º C).
A flexible drain hose is provided to make installation, servicing and maintenance easier.
Make sure that the water is free from calcium and hard water deposits. For these situations, an on-
line water cartridge system is highly recommended. Build-up of calcium and lime deposits in the
washer may occur and servicing will be required on a more frequent basis which will not be
covered by the warranty.
**DRAIN**:
This dishwasher has a gravity drain. Maximum height of the drain should not exceed 20" (50cm).
A 1.5" ID flexible drain hose is provided to facilitate maintenance and servicing of the
machine.
ELECTRICAL:
A 208-240 volt, 60 Hz, Single Phase or Three Phase circuit is required for this unit. Check the
rating plate on the machine for amp draw and phase. Pump rotation must be verified on 3 phase units
at time of install. In spite of the fact that the rating plate shows 208 volts, the unit is designed
function properly from 208 volts to 240 volts.
The terminal block is located under the control panel, inside the machine. Pass the cable through
the cable strain relief at the back and connect the wires to the terminals L1 (brown wire), L2 (blue
wire), L3 (black wire) & Ground (yellow & green wire). There should be sufficient cable length to
permit the machine to be pulled out for service.
DO NOT manually fill wash tank with water. The dishwasher will fill
automatically when the power is turned ON.
IMPORTANT NOTE
Reasonable access to and around the machine for service must be provided.
Disconnecting of hard plumbing or removal of counter tops or cabinets, etc., for servicing
is not covered by warranty.
Verification of the pump rotation is very important!
All panels must be on the unit when the installation is finished.
* - not supplied
** SEE PAGE 6 FOR FURTHER IMPORTANT DETAILS**
17
Page 18
RINSE ADDITIVE
BLUE TUBE
DETERGENT
RED TUBE
F-18DP
CHEMICAL PUMPS
Models 727, 737, 747, 767, F-14, F-16DP, F-18, F-18DP, F-20 & F-22 are supplied with
factory installed liquid detergent and rinse additive pumps to automatically dispense during
each wash & rinse cycle. Before accessing the bottom section of the dishwasher, make sure
that the power is turned off at the
source (breaker panel).
The bottom panel can only be
removed with a flat tool like a screw-
driver. Insert the screw-driver in the
gap between the front panel and the
side panel. Pry open towards you.
Do this on both sides.
The red & blue hoses connected to the pumps must be routed out of the
bottom of the dishwasher. The red tube is for detergent and the blue tube is for
rinse additive. The containers can be either to the right or left of the
dishwasher. Perforating the stainless panel is not recommended.
The two chemical pumps are factory adjusted to accommodate most installations.
There is a mark on the pump indicating this setting.
It is recommended that only qualified personnel alter these settings.
UNDER NO CIRCUMSTANCES should the detergent pump be
turned off.
18
Page 19
19
RINSE PRESSURE
20-30 PSI
RINSE FLOW INDICATOR
DETERGENT FLOW INDICATOR
F-18DP
VISUAL CHEMICAL DELIVERY VERIFICATION
The peristaltic chemical pumps are located in the base of the dishwasher. They
feature a transparent cylinder (1) to visually see if fluid is passing through the
pumps. The pumps are automatically energized during the “initial fill” (when
turning on the dishwasher) and “rinse cycle” (after the wash cycle). During this
time, the flow indicator (2) will move between the “Min Flow” position and the
“Max Flow” position (3) in the cylinder. It is normal for the pumps to cycle on and
off.
If the flow indicator (2) does not move during the fill or rinse, no fluid is
circulating through the pump. It is recommended not to use the dishwasher until
this condition is resolved.
TROUBLESHOOTING
30 PSI
1. Ensure that there is sufficient chemical in the container and that the tube is not kinked.
The filter on the end of the tube must reach to the bottom of the container. If the filter or
tube is blocked, remove and soak in warm water to dislodge the obstruction.
2. There may be air in the pump. To “Prime” the pumps (remove the air), turn off and drain
the dishwasher. Replace the stand pipe, close the door and turn on the dishwasher. The
pumps will be activated as the machine fills. The Flow Indicators (2) should start to move
by the time the machine has filled. If not, repeat the drain and fill.
3. The Squeeze Tube (flexible tube inside the pump) is worn or perforated. This part is a
normal wear and tear item that must be replaced periodically (when pump performance
diminishes). Call for Service.
4. The pump does not operate - the roller in the middle of the pump does not turn during the
fill or rinse. Call for Service.
For any other request on set-up and installation, please contact us toll free at 1 888 275 4538
extension 611 or (514) 737-9701 (International)
IMPORTANT: Remember to always use caution and protective gear whenever you are
manipulating chemicals. They can burn the skin. Follow the manufacturer’s instructions carefully.
Page 20
1
8
F-18DP
CONTROL P
ANELS
7
ON
OFF
2
5
4
P
7
3
6
6
5
1
4
3
6
7
1 Green Power Button Switch
2 Power ON Indicator Light
3 Rinse Temperature Gauge
4 Wash Temperature Gauge
1
2
5
3 4
5 “READY” Indicator Light
6 Cycle Start Button
7 Cycle Indicator Light
8 White Drain Pump Button
20
Page 21
BASIC STEPS TO START
Begin with an empty dishwasher. The wash tank should be empty.
Make sure the filter screens and the overflow pipe are in place.
Close the door.
Push the square green button. The dishwasher will take about two minutes
to fill and 20 minutes to heat the water. The booster (rinse) will heat up first
and then the wash tank will heat up.
When the dishwasher is ready, the ready light will come on. This indicates
that the dishwasher has reached optimum temperature.
You can now start washing.
Fill the basket. Only one basket can be used at a time.
Slide it in to the dishwasher.
Close the door and press the round black button. The dishwasher will start
washing for a few minutes. When the wash pump stops, the rinse is about to
start. Verify that the Rinse Pressure Gauge (P.6) is showing 20-30 PSI and
that the Chemical Flow Indicators (P.19) are moving. The rinse continues for
approximately 20 seconds.
When the cycle light (near the start button) goes off, open the door and
remove the tray to let air dry.
If you are ready for another wash, slide a basket in the dishwasher, close the
door & press the Cycle Start Button. If not, just close the door to retain the
heat in the dishwasher and conserve energy.
You should drain the dishwasher at least once a day or when the water is soiled.
The dishwasher should be turned off, drained, cleaned and left empty at night.
To drain the dishwasher, follow these simple steps;
Turn OFF the power.
Pull out the overflow tube (CAUTION: water may be hot)
Press the white drain button (if so equipped) until all the water is gone. Be
careful not to let any debris go down the drain as it may block the pump.
21
Page 22
OPERATION
Before operating the machine, ensure that the electrical power, water supply and drain connections
have been made as per the installation instructions.
Ensure that the overflow pipe is correctly set in its place (inside the wash tank). The overflow pipe
should never be forced into its position. For the first use of the day, the wash tank should not have
any water.
Familiarize yourself with the gauges, buttons and indicator lights on the
control panel.
Check chemical levels. The containers should have sufficient quantities
of Detergent (for wash) and Rinse Additive (drying agent).
Press the Square Green Power Button (1).The Power Indicator Light
will illuminate (as well as the Digital Temperature Gauges , if so equipped).
If the wash tank is empty, the machine will start to fill. Always keep the door
closed during this time. When the machine has filled to its required water
level, the elements will then raise the rinse and wash
water temperatures automatically.
It will take approximately 15-20
minutes in order to obtain the
optimum temperatures (185°F in the
booster and 160°F in the wash tank).
The Ready Indicator Light (5) will
illuminate to indicate that the machine
is ready for its first load.
Fill the basket with dishware and
trays then push the basket into the
machine.
It is more economical to wash
when the basket is fully loaded. It is
also important not to overload the
basket. Water should always be
able to spray freely around the
dishware and trays.
Press the round black Cycle Start
Button (6) to start the wash cycle.
On the model 767, set the selector to 2, 4 or 6 minute wash.
Closing the hood on Models F-22, 747 & 767 will automatically start the cycle. The Cycle Indicator
Light (7) will illuminate. The cycle starts and consists of a wash (up to 6 minutes), a brief pause and
then a rinse (from 18 to 25 seconds). Another basket can be filled while the first one is being
washed. The Cycle Indicator Light (7) will extinguish to signal the end of the cycle. It is important to
remove the basket from the machine while they are hot to let the dishes air dry. They will not dry if
left in the machine.
Overflow
Stand pipe
Overflow
Heater
Water Level
Air Trap
!Do Not Touch
Wash arm
Wash pump
Filter
22
Page 23
IMPORTANT NOTES:
-The
models F-22, 747 and 767
to initiate the wash cycle. Once the unit has filled up with water and the
temperatures have reached their maximums, slide the basket in and close the door.
Closing the door will start the wash cycle. At the end of the cycle, after the cycle
light has switched off, open the door and remove the basket. The cycle light will
come on at that point for a few seconds to reset the timer for the next wash.
- JET-TECH high temperature warewashers do not dump water and fill after every
cycle. The wash water is refreshed during every cycle by the hot
rinse water. Only excess water is expelled from the machine via the overflow
pipe. If the wash water becomes soiled, it is recommended turn off and drain the
dishwasher, clean
all debris from the filters and wash tank and turn on the dishwasher to
fill with fresh water
- Some models are equipped with an automatic drain pump (White button on the
front control panel) that will evacuate excess water. Please see the section
on: DRAIN PUMP OPERATION.
- During the rinse cycle, verify that Rinse Pressure is 30 PSI and that
the Chemical Flow Indicators are moving.
- IMPORTANT: If the dishwasher will not be used for two (2) or more hours, it should
be drained and turned off. The dishwasher should never be left in the “ON” position
and unattended.
differ from the under-counter units in the way
23
Page 24
Jet-Tech F-
BASIC STEPS TO O
18
D
P
PERATE
185 F
Make sure dishwasher is empty (no water)
and the
debris.
filters & wash tank
are clean of
Close the door and press the power
button. Wait
attain optimum washing temperatures.
20 minutes for the water to
165 F
3
Pre-rinse dishes and/or glasses and cups. Load rack in the dishwasher and
close the door. Only one rack at a
time.
2
4
5
Press the Start button.
Wash cycle is 3 minutes
.
Wait for the green light to turn off
before taking the tray out
Take tray out to let dishes air dry
.
6
.
24
Page 25
F-
22
BASIC STEPS TO O
At the start of each day,
ensure dishwasher is empty (no water)
and that the wash tank is clean (no debris)
Pre-rinse dishes, glasses and cups
.
PERATE
1
3
160 F
Close the door,
press the Power B
Wait for the water to obtain
optimum washing temperature
Load rack in the dishwasher
and close the door. Only one rack at a
time.
utton to ON.
.
2
185 F
4
5 6
Close the door to start the wash cycle
.
Wait for the green light to turn OFF
before removing the rack
Repeat from step
3 for more trays.
.
25
Page 26
DRAIN PUMP OPERATION
Models 727, 737, F-16DP and F-18DP are factory built with drain pumps. A square white button
on the control panel beside the green power button also evidences this feature. All other models
have a gravity drain.
Drain pump equipped models will pump the waste water to a maximum height of 36” (0.9 meter). A
1” ID flexible hose of sufficient length is provided to facilitate maintenance and servicing of the
machine. It is important not to reduce the size of this hose. A 1” check valve* may be required. There
should be sufficient hose length to permit the machine to be pulled out for service. Drainage time
should not exceed 1 minute.
The drain pump activates automatically during a rinse cycle and functions when the water fill valve
is open: during the fill and rinse cycles. This allows the removal of excess water entering the unit.
To manually drain the wash tank, you must:
1. -Turn off the machine (square green button on control panel).
2. -Open the door, remove the basket, and remove the overflow pipe (also known as stand pipe).
3. -Press and hold the white button on the control panel, which will activate the drain pump.
Release the button when the water has been discharged.
The most common causes of drain pump failure are:
-Debris was flushed down the drain and blocked the impeller in the pump. Removing the impeller
cover and clearing the obstruction generally restores normal pump function.
-The drain hose, at the back of the unit, is restricted.
IMPORTANT! Pump failure caused by debris blockage is NOT covered by the warranty.
Push and Hold
* - not supplied
26
Page 27
27
Page 28
PROBLEM ANALYSIS
INDEX
1. Constantly fills
2. Dishwasher makes a high
pitch noise when washing
3. Dishwasher overflow
4. Does not operate/start
5. Does not wash properly
6. Filling is too long. Exceeds 3
minutes.
7. Filling is too short (under 1
minute)
>The water level system may have
an air leak.
>>verify the water level system
from the pressure switch to the tube
down to the air trap. Replace the
defective parts as required.
>The air trap may have dirt in it.
>>Clean the air trap.
2. Dishwasher makes a high
8. Machine takes too long to pitch noise when washing
empty. Time exceed 2 minutes.
9. Pilot lamps do not illuminate >The wash tank may have too
10. Spots on glasses much detergent.
11. The wash pump does not >>Too much soap may cause the
operate consistently during a pump to make a high pitch noise.
wash cycle Reduce the detergent amount; and
12. Wash cycle is too short ensure it is of the non-foaming type
used. The mechanical seals may be
PROBLEM
worn. Replace as required.
>CHECK
>>ACTION
1. Constantly fills
>Dishwasher has inactive/not been
drained in a long time (more than
three hours).
>>Switch dishwasher OFF. Pull
over-flow and drain unit completely.
Once drained, clean wash tank and
filters. Put all parts back in. Close
door, switch it ON, and let fill.
>Is overflow tube(stand-pipe)
properly positioned in wash tank?
>>Check for cracks or burrs at
bottom of overflow tube.
>The air pressure switch may be
faulty.
>>Replace switch.
3. Dishwasher overflow
>Drain outlet hose may be blocked.
>>Un-clog or reposition hose or
replace the drain hose.
>Drain pump may be blocked or
defective not allowing proper
drainage of machine.
>>Un-clog or replace drain pump,
as required.
>Incoming water pressure may be
incorrect.
>> If the water pressure is too high
(above 30 psi), you must install a
pressure regulator.
>Regular dishwashing soap may
have been used or has
contaminated the dishwasher
accidentally, causing an excessive
amount of sudsing.
>>Drain the tank, remove as much
28
Page 29
suds as possible. Leave overflow >>Verify all connections.
out, close the door and put power
on. Let unit run for 2 to 4 minutes. >Verify that power is going to the
Turn off unit, put overflow back in, machine.
close the door and refill unit. Try >>Verify the breaker or fuses. Verify
washing. If reoccurs try from the electrical connections to the
beginning again. machine.
>The solenoid valve may have dirt
in it or may be defective.
>>Clean the filter or replace as
required.
4. Does not operate or start
5. Does not wash properly
>Are the scrap screens clean?
>>Clean the scrap screens & filters.
Don't forget the wash pump screen.
>The door micro switch may be >Are the wash/rinse arm jets
defective. clogged?
>>Adjust switch. Some of the parts >>Clean the jets/nozzles. Be
may have to be replaced. careful not to lose the o-rings.
>The momentary relay may be >Detergent system may be
defective or disconnected. defective.
>>All wires must well in place. If so >>Peristaltic hose(s) may have to
replace it. be replaced. The detergent filter in
the container may be clogged or
>The power switch may be worn. Replace. Check the detergent
unplugged or defective. line for deposits. Clean the line if
>>Verify connections and replace necessary.
as required.
>Dishes appear dirty after the cycle
>The pressure switch may be faulty. is completed.
>>Adjust switch. Replace as >>Pre-rinse the dishes properly
required. before they are placed into the dish
racks.
>The solenoid valve may have dirt
in it or may be defective. >Drain outlet hose may be blocked.
>>Clean filter or replace as Drain pump may be blocked or
required. defective, and is not allowing proper
drainage of machine.
>The timer may be defective. >>Un-clog, reposition hose or
>>Replace. change drain hose. Un-clog or
replace drain pump, as required.
>The washing cycle button may be
defective. >Incoming water pressure may be
>>Replace. either too low or too high will result
in poor rinsing.
>The wiring may have a break or >>If the pressure is too low (under
short to ground. 20 psi), check that the valve is fully
29
Page 30
>>Clean the air trap.
opened. If it is, the customer may
need to install a pressure-booster
pump to increase the water pressure.
If the water pressure is too high
(above 30psi), you must install a
pressure regulator.
>Is the wash water clean?
>>Drain the tank, rinse and refill.
>Is the water level in the wash tank
correct?
>>Water level should be just under
the opening of the overflow pipe. Too
little water will cause the wash pump
to draw air. Too much water will keep
the arm from spinning properly and
may cause water to come out the
door. Both cases reduce the
performance of the dishwasher.
>Small specs remain on glasses
after rinsing.
>Have the incoming water analysed.
May need a filtering system.
>The air pressure switch may be
faulty.
>>Replace Pressure switch
>The air trap may have dirt in it.
>The detergent used is of poor
quality.
>>Replace with a better quality
commercial brand or increase
dosage.
>The solenoid valve may have dirt in
it or may be defective.
>>Clean filter or replace as required.
>Wash pump may be clogged or
defective.
>>Open face plate of wash pump for
inspection. Clean wash pump or
replace it if necessary.
6. Filling is too long. Exceeds 3
minutes.
>Incoming water pressure may be
incorrect.
>>If the pressure is too low (under
20 psi), check that the faucet is fully
opened. If it is, the customer may
need to install a pressure-booster
pump to increase the water pressure.
>The stand-pipe may be set
incorrectly.
>>Remove the stand-pipe and check
the seat for dirt.
>The air pressure switch may be
faulty.
>>Adjust or replace as required.
>The air trap may have dirt in it.
>>Clean the air trap.
>The solenoid valve may have dirt in
it or may be defective.
>>Clean filter or replace as required.
7. Filling is too short (under 1
minute)
>The air pressure switch may be
faulty.
>>Adjust or replace as required.
>Incoming water pressure is
probably too high (above 30PSI
flow).
>>Install a water
Pressure Reducing Valve.
>The air trap may have dirt in it.
>>Clean the air trap.
30
Page 31
8. Machine takes too long to
drain. Time exceed 2 minutes.
Should be less than 1 minute.
>Drain outlet hose may be blocked
or kinked.
Drain pump may be blocked or
defective not allowing proper
drainage of machine.
>>Un-clog or reposition hose or
replace the drain hose. Un-clog or
replace drain pump, as required.
>The overflow pipe may be
clogged.
>>Clean out any residue.
9. Pilot lamps do not illuminate
>Pilot lamps may be faulty.
>>Check connections. Replace as
required.
>The power switch may be
unplugged or defective.
>>Verify and replace as required.
>>Verify the breaker.
>>Verify electrical connections
behind the machine
10. Spots on glasses
>Rinse aid pump may need to be
primed or adjusted.
>>Prime or adjust. Replace as
required.
>The rinse agent may be of an
inferior quality.
>>Replace with a quality commercial
brand.
11. The wash pump does not
operate consistently during a
wash cycle
>Machine may not be leveled.
>>Level the dishwasher.
>The air pressure switch may be
faulty.
>>Adjust or replace as required.
>The air trap may have dirt in it.
>>Clean the air trap.
>Water level in wash tank is too low.
>>Adjust pressure switch or replace
as required. Water level should be
level with the stand-pipe opening.
12. Wash cycle is too short
>The timer may be defective.
>>Replace.
IMPORTANT NOTES
Locate and clearly identify the water
shut-off valve that supplies the
dishwasher and the fuse box or
breaker switches.
Only qualified and/or licensed
technician can repair this piece of
equipment. Removing panels exposes
wires and live current. The breaker
should be switched off or fuses
removed before servicing or removing
the panels. The water supply must also
be turned off.
Don’t expose yourself injury.
Call Jet-Tech for service or support.
31
Page 32
BLANK PAGE
Page 33
Do you have any questions?
Do you need service?
Phone:
888-275-4538 toll free
(514) 737-9701
Fax:
877-453 8832 toll free
(514) 737-2792
Email: service@jet-tech.com
MODEL:________________
SERIAL:________________
DATE INSTALLED:_______
SERVICE:
33
Page 34
OWNER’S MANUAL
DISHWASHER INSTALLATION,
OPERATION AND MAINTENANCE
FOR OPERATOR. DO NOT DISCARD
010
Loading...