JetI USA Duplex DS-6 User Manual

1
12
1.4 Main Function Interface
1.5 LED Displaying Board Function
1.6 Menu
13
15
16
17
17
18
18
19
19
20
20
21
21
22
22
23
24
24
25
DS-6
23
1.1 Transmitter Chart
45
4.0V.
Voltage
Model Memory
4.8V
MOD6
SYS.
TIMER 00:00
FUN.
Function
System
Timer
F100
4.0
F100
4.8V
MOD6
SYS.
TIMER 00:00
FUN.
F100
12. 2.4GHz Binding
13. Basic Features
14. Main function Interface
15. LED Display Board
Make sure that the transmitter is on the correct model and powered off. Place binding plug in the EXT port on the receiver and power up receiver. Turn on the transmitter and when it binds, remove the binding plug from the receiver. Model is now bound.
1. The Binding Process
67
TIMER SET
4.8V
MOD6
TIMER 00:00
FUN.
F100
SYS.
1.6 MENU
2.1 System menu introduction
MODEL SET(Page8~9)
PLANE TYPE(Page10)
89
2.2 MODEL SET
1011
.
1)Press“down”to select “SYS MENU”,and press“ENTER”to come to the interface.
2)Press“up”or“down”to select “NORMAL”or“TRAINER”.
TIMER SET
TIMER SET
TRAINER
2.3 PLANE TYPE
2.4 STICK MODE
2.5 STICK ADJ
2.6 TRAINER
1213
4.8V
MOD6
SYS.
TIMER 00:00
FUN.
2.7 TIMER SET
Choose Timer set
Operation
1. Press Down to select Sys Menu, and press Enter to the interface
2. Down button select Timer SET
3. Up and Down button setting time M:S
4. Entering setting Timer Press INC or DEC choosing increase and decrease
5. Return main Interface. INC -- TIMER START DEC -- TIMER RESET
Caution:This setting before and after 20seconds each two seconds Alarm.
after Alarming each 10 seconds. then Alarm not stop.
Press DEC --- TIMER RESET LOGOUT TIME RENEW TIMER
3.1 Functions. Menu Introduction (Heli)
DR(Page 14)
SUB TRIM(Page 16)
TRAVEL(Page 17)
TRAVEL(Page 17)
1415
SUB.TRIM
A/E/R D/R
A/E/R D/R
3.2 D/R
SWASH MIX(Page 18)
GYRO.SENS(Page 18)
THRO.CURV(Page 19)
MONITOR(Page 19)
PIT.CURV(Page 20)
THRO.HOLD(Page 20)
1617
A/E/R D/R
3.3 SUB TRIM
3.4 TRAVEL
3.5 CH.REV
1819
Monitor system
Operation:
1)Press“up”to select “FUN MENU”,and press“ENTER”to come to the interface.
2)Press“up”or“down”to select “MONITOR”,and now the shadow area is the item that can
be set currently.Press“ENTER”to go to the next step.
3)When you move the sticks or channel switches,you can find the corresponding channel bars will
change accordingly.This function is designed to monitor the working conditions of the
transmitter.
4)After your setting,press “EXIT”to save the setting and leave the operation.
Remark:this function helps you adjust the setting,neutral trim as well as channel inspection.
Throttle curve operation
Operation:
1)Press“up”to select “FUN MENU”,and press“ENTER”to come to the interface.
2)Press“up”or“down”to select “THRO CURV”,and now the shadow area is the item that
can be set currently.Press“ENTER”to go to the next step.
3)Press“ENTER” to select the throttle curve point.There are 5 points,they are L,1,2,3,H.
Press“INC”or“DEC”to set the corresponding value separately,and the throttle curve will
change accordingly.
4)There are three throttle curves to be selected,normal,“IDLE 0”and“IDLE 1”by the switch at
the left top of the transmitter..
5)After your setting,press“EXIT”to save the setting and leave the operation.
Remark:the transmitter can save 3 groups of different throttle curves.When you make 3D fly,
please ask for instruction from experienced pilots.
3.6 SWASH.MIX
3.7 GYRO.SENS
3.8 THRO CURV
3.9 MONITOR
2021
3.10 PIT.CURV
3.11 THRO.HOLD
4.1 Function menu for fixed wing plane
4.2 V-Tail Function Menu
2223
4.3 Delta mix function menu
5.1 Heli.Connection Diagram(3Servos CCPM)
2425
5.3 V-Tail Connection Diagram
DELTA-MIX Connection Diagram
Technology Data
DS-6
Loading...