JET VBS-18MW Operating Instructions and Parts Manual

This .pdf document is bookmarked

Operating Instructions and Parts Manual

18-inch Metal/Wood Cutting Band Saw

Model VBS-18MW

JET

(ECR TW0126)

2016 JET

1.0 Warranty and Service

JET® warrant s ever y pro duct it sel l s against m anuf acturers’ defec ts. If one of ou r tools needs ser vice o r repair, pleas e contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday.

Warranty Period The general warranty lasts for the time period specified in the literature included with your product or on the official JET branded website.

• JET products carry a limited warranty which varies in duration based upon the product. (See chart below)

• Accessories carry a limited warranty of one year from the date of receipt.

• Consumable items are defined as expendable parts or accessories expected to become inoperable within a

reasonable amount of use and are covered by a 90 day limited warranty against manufacturer’s defects.

Who is Covered

This warranty covers only the initial purchaser of the product from the date of delivery.

What is Co vered

This warranty covers any defects in workmanship or materials subject to the limitations stated below. This warranty does not cover failures due directly or indirectly to misuse, abuse, negligence or accidents, normal wear-and-tear, improper repair, alterations or lack of maintenance. JET woodworking machinery is designed to be used with Wood. Use o f these ma chin es in t he process ing of metal, plastics, or other ma teri als outside r ecommended gui delines m ay void the warranty. The exceptions are acrylics and other natural items that are made specifically for wood turning.

Warranty Limitations

Woodworking products with a Five Year Warranty that are used for commercial or industrial purposes default to a Two Year Warranty. Please contact Technical Service at 1-800-274-6846 for further clarification.

How to Get Technical Support Please contact Technical Service by calling 1-800-274-6846. Please note that you will be asked to provide proof of initia l p u rch a s e whe n calling. If a product requires further inspection, the Technical Service representative will

explain and assist with any additional action needed. JET has Authorized Service Centers located throughout the United States. For the name of an Authorized Service Center in your area call 1-800-274-6846 or use the Service Center Locator on the JET website.

More Informat io n

JET is constantly adding new products. For complete, up-to-date product information, check with your local distributor or visit the JET website.

How S tate Law Applies

This warranty gives you specific legal rights, subject to applicable state law.

Limitations on This Warranty

JET LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD OF THE LIMITED WARRANTY FOR EACH PRODUCT. EXCEPT AS STATED HEREIN, ANY IMPLIED WARRANTI ES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE EXCLUDED. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

JET SHALL IN NO EVENT BE LIABLE FOR DEATH, INJURIES TO PERSONS OR PROPERTY, OR FOR INCIDENTAL, CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF OUR PRODUCTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

JET sells through distributors only. The specifications listed in JET printed materials and on official JET website are given as general information and are not binding. JET reserves the right to effect at any time, without prior notice, those alterations to parts, fittings, and accessory equipment which they may deem necessary for any reason whatsoever. JET

Product Listing with Warranty Period

90 Days – Parts; Consumable items 1 Year – Motors; Machine Accessories 2 Year – Metalworking Machinery; Electric Hoists, Electric Hoist Accessories 5 Year – Woodworking Machinery Limited Lifetime – JET Parallel clamps; VOLT Series Electric Hoists; Manual Hoists; Manual Hoist Accessories; Shop Tools; Warehouse & Dock products; Hand Tools; Air Tools

NOTE: JET is a division of JPW Industries, Inc. References in this document to JET also apply to JPW Industries, Inc., or any of its successors in interest to the JET brand.

branded products are not sold in Canada by JPW Industries, Inc.

2.0 Table of Contents

1.0 Warranty and Service ....................................................................................................................... 2

2.0 Table of Contents ............................................................................................................................. 3

3.0 Safety warnings ................................................................................................................................ 4

4.0 Introduction ....................................................................................................................................... 6

5.0 Specifications ................................................................................................................................... 6

6.0 Grounding Instr uc tions ...................................................................................................................... 6

6.1 115 Volt Operation ........................................................................................................................ 7

6.2 230 Volt Operation ........................................................................................................................ 7

6.3 Extension cords ............................................................................................................................. 7

7.0 Unpacking ......................................................................................................................................... 8

7.1 Contents of Shipping Container ..................................................................................................... 8

8.0 Assembly .......................................................................................................................................... 9

8.1 Handwheel .................................................................................................................................... 9

8.2 Mounting the Table........................................................................................................................ 9

8.3 Rail Assembly ............................................................................................................................... 9

8.4 Chip Tray .................................................................................................................................... 10

8.5 Dust Collection ............................................................................................................................ 1 0

8.6 Fence Assembly and Adj ustm ent................................................................................................. 10

8.7 Resaw Guide .............................................................................................................................. 1 2

8.8 Miter Gauge ................................................................................................................................ 12

9.0 Adjustments .................................................................................................................................... 12

9.1 Table Tilt ..................................................................................................................................... 12

9.2 Adjusting 90 Degree Table Stop .................................................................................................. 13

9.3 Speed Adjustm ents ..................................................................................................................... 13

9.4 Installing/ Changing Blades .......................................................................................................... 14

9.5 Blade Tension ............................................................................................................................. 15

9.6 Blade Tracki ng ............................................................................................................................ 15

9.7 Overview – Bearing Adjustments ................................................................................................. 16

9.8 Upper Bearing Adjustments ......................................................................................................... 16 

9.9 Lower Bearing Adjustments ......................................................................................................... 17

9.10 Blade Lead ................................................................................................................................ 18

9.11 Replacing the V-Belt .................................................................................................................. 19

9.12 Belt Tension .............................................................................................................................. 19

9.13 Pulley Alignment ....................................................................................................................... 20

10.0 Electric al Connec tions................................................................................................................... 20

11.0 Operation ...................................................................................................................................... 2 1

11.1 General Proc edur e .................................................................................................................... 21 

11.2 Ripping...................................................................................................................................... 21

11.3 Crosscutting .............................................................................................................................. 21

11.4 Resawing .................................................................................................................................. 22 

11.5 Saw Blade Selecti on.................................................................................................................. 22

11.6 Blade Breakage ......................................................................................................................... 23 

12.0 Maintenance ................................................................................................................................. 23

12.1 Replacing Tires ......................................................................................................................... 24

13.0 Periodic Maint enanc e ................................................................................................................... 24

14.0 Blade Selection Guide................................................................................................................... 25 

15.0 Blade Speed per Mat eri als Chart .................................................................................................. 26

16.0 Troubleshooti ng VBS-18MW Band Saw ........................................................................................ 2 7

17.0 Replacement Parts ....................................................................................................................... 29

17.1.1 Upper Wheel Assembl y .......................................................................................................... 30 

17.1.2 Parts List: Upper Wheel Assembly .......................................................................................... 31 

17.2.1 Lower Wheel and Motor A ssembly .......................................................................................... 32 

17.2.2 Parts List: Lower Wheel and M otor Assembly ......................................................................... 33

17.3.1 Blade Guide Assem bly ........................................................................................................... 35

17.3.2 Parts List: Bl ade Guide Assembly ........................................................................................... 36

17.4.1 Table and Fence Assembly .................................................................................................... 38

17.4.2 Parts List: Table and Fence Assembly .................................................................................... 39

18.0 Electric al Connec tions................................................................................................................... 40

3.0 Safety warnings

1. Read and understand the entire owner's manual before attempting assembly or operation.

2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury.

3. Replace the warning labels if they become obscured or removed.

4. This band saw is designed and int ended for use by properly trained and experienced personnel only. If you are not familiar with the proper and safe operation of a band saw, do not use until proper training and knowledge have been obtained.

5. Do not use this band saw for other than its intended use. If used for other purposes, JET, disclaims any real or implied warranty and holds itself harmless from any injury that may result from that use.

6. Always wear approved safety glasses/face shields whil e using this band sa w. Every day eyeglasses only have impact resistant lenses; they are not safety glasses.

7. Before operating this band saw, remove tie, rings, watches and other jewelry, and roll sleeves up past the elbows. Remove all loose clothing and confine long hair. Nonslip footwear or anti-skid floor strips are recommended. Do not wear gl ov es.

8. Wear ear protectors (plugs or muffs) during extended periods of operation.

9. Some dust created by power sanding, sawing, grinding, drilling and other construction activities contain chemicals known to cause cancer, birth defects or other reproduct ive harm. Some examples of these chemicals are:

• Lead from lead based paint.

• Crystalline silica from bricks, cement

and other masonry product s.

• Arsenic and chromium from chemically

treated lumber.

Your risk of exposure v aries, depending on how often you do this type of work. To reduce your exposure to these chemicals, work in a well-ventil ated area and work with

approved safety equipment, such as face or dust masks that are specificall y designed to filter out mi croscopi c par ticles.

10. Do not operate this machine while tired or under the influence of drugs, alcohol or any medication.

11. Make certain the switch is in the OFF position before connecting the machine to the power supply.

12. Make certain the machine is properly grounded.

13. Make all machine adjustments or maintenance with the machine unplugged from the power source.

14. Rem ove adjusti ng keys and wrenches. Form a habit of checking to see that keys and adjusting wrenches are removed from the machine before turning it on.

15. Keep safety guards in place at all times when the machine i s in use. If removed for maintenance pur poses, use ext rem e cauti on and replace the guar ds immediately.

16. Check dam aged parts. Bef ore furt her use of the machine, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may aff ect its operation. A guard or other part that is damaged should be properly repaired or replaced.

17. Provide for adequate space surrounding work area and non-glare, overhead lighti ng.

18. Keep the floor around the machine clean and free of scrap mat eri al, oil and grease.

19. Keep vi sitors a safe distance f rom the work area. Keep chi ld ren away.

20. Make your workshop child proof with padlocks, master switches or by removing starter keys.

21. G ive your work undivi ded attention. Look ing around, carrying on a conversation and “horse-play” are c ar eless acts that can result in serious injury.

22. Maintain a balanced stance at all times so that you do not fall or lean against the blade or other moving parts. Do not overreach or use excessive force to perform any machi ne operation.

23. Use the right tool at the correct speed and feed rate. Do not force a tool or attachment to do a job for which it was not designed. The right tool will do the job better and safer.

24. Use recommended accessories; improper accessories may be haz ar dous.

25. M aintain tools with car e. Keep blades sharp and clean for the best and safest performance. Follow instructions for lubricating and changing accessories.

26. Turn off t he machine befor e cleaning. Use a brush or compressed air to remove chips,

Familiariz e you rself with the following safety no tices used in this manual:

This means th at if precaut ions are n o t heeded, it may resul t i n minor i njury and /or

possible machine damage.

This means that if p recautions are not heeded, it may result in serious injury or

possibly even d eath.

shavings or debris — do not use your hands.

27. Do not stand on t he machi ne. Serious inj ury could occur if the machine tips over.

28. Never leave the machine running unattended. Turn the power off and do not leave the machine until it comes to a complete stop.

29. Rem ove loose items and unnecessary work pieces from the area before starting the machine.

- - SAVE THESE INSTRUCTIONS - -

4.0 Introduction

This manual is provided by JET, covering the safe operation and maintenance procedures for a JET Model VBS-18MW Band Saw. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakd own. This machine has been designed and constructed to provide consistent, long-term operation if used in accordance with instructi ons set forth in this manual. If there are any questions or comm ents, please contact either your local suppli er or JET. JET can also be reached at our web site: www.jettools.com.

5.0 Specifications

Model Number ............................................................................................................................... ....... VBS-18M W

Stock Number ............................................................................................................................................. 414418

Cutting Capacity (height) (in.) ............................................................................................................................. 12

Cutting Capacity (width) (in.) ......................................................................................................................... 18-3/8

Maximum Rip Left of Blade w/Fence (in.) ..................................................................................................... 16-1/2

Blade Length (in.) .............................................................................................................................................. 137

Blade Speeds (SFPM):

High Gear .............................................................................................................................. 1000, 1800, 3200

Low Gear ....................................................................................................................................... 80, 150, 265

Minimum Blade Width (in.) ................................................................................................................................. 1/8

Maximum Blade Width – Wood (in.) ................................................................................................................ 1-1/2

Maximum Blade Width – Metal (in.) ...................................................................................................................... 1

Table Size (in.) ............................................................................................................................................ 19 x 19

Front of Table to Center of Blade (in.) ................................................................................................................. 10

Table Tilt (deg.) ................................................................................................................................... 45°R to 10°L

Table Height from Floor (in.) ......................................................................................................................... 37-1/2

Wheel Diameter (in.) ..................................................................................................................................... 18-5/8

Dust Port Diameter (in.) ....................................................................................................................................... 4

Base Footprint (in.) ...................................................................................................................................... 18 x 29

Overall Dimensions (HxWxD) (in.) ...................................................................................................... 74 x 42 x 38

Motor ................................................................................................... 1-1/2 HP, 1Ph, 115/230V (pre-wired 115V)

Net Weight – approximate (lbs.) ........................................................................................................................ 456

Shipping Weight – approximate (lbs.) ............................................................................................................... 582

The above specifications were current at the time this manual was published, but because of our policy of continuous impr ov ement, JET reserv es the right to change specif ications at any time and without pri or notice, without incurring obligati ons.

Do not modify the pl ug provided. If it will not fi t

6.0 Grounding Instructions

Electrical connections must

be made by a qualified electrician in compliance with all relevant codes. The machine must be properly ground ed to help prevent electrical shock and possible fatal injury.

In the event of a malfunction or breakdown, grounding provi des a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an elec tric cord having an equipment- groundi ng conduct or and a grounding plug. T he plug must be plugged into a matching outlet that is properly installed and grounded in accordanc e with all local codes and ordinances.

the outlet, have the proper outlet installed by a qualified elec trician.

Improper connection of the equipmentgrounding conductor can result in a risk of electric shock. The conductor, with insulation having an outer surface that is green with or without yellow stripes, is the equipmentgrounding conduct or. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment -groundi ng conductor to a live terminal.

Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the tool is properl y grounded. Use only three wire extension cords that have thr ee-prong grounding plugs and t hree-pole recept acles that accept the tool ’s pl ug.

6.1 115 Volt Operation

The VBS-18MW band saw is wired from the factory for 115 volt operation. The power cord has a plug that looks like A, Figure 1, and is used in an outlet that looks like B, Figure 1. A temporary adapt er wit h a grounding ear secured with a screw (C, Figure 1) may be used to connect this plug to a two-pole receptacle if a properly grounded outlet is not available. The temporary adapter should only be used until a properly grounded outlet can be installed by a qualified electrician. This adapter is not applicable in Canada. The green colored grounding ear, lug, or tsab, extending from the adapter, must be connected to a permanent ground such as a properly grounded outl et box, as shown in C, Figure 1.

available or should be used with the 230V plug.

Figure 2

It is recommended that the Band Saw when operated at 230 volts, be connected to a dedicated, minimum 15 amp circuit with a 15 amp circuit breaker or time delay fuse. Local

codes take precedence over recommenddations.

Important: In all cases (115 or 230 volts), make

certain the receptacle in question is properly grounded. If you are not sure, have a regi stered electrici an c hec k the rec eptacle.

Figure 1

It is recommended that the Band Saw when operated at 115 volts, be connected to a dedicated, minimum 30 amp circuit with a 30 amp circuit breaker or time delay fuse. Local

codes take precedence over recommendations.

6.2 230 Volt Operation

If 230V, single phase operation is desired, the following inst r uc tions must be followed:

1. Disconnect machine from the power source.

2. This band saw is supplied with four motor leads that are connec ted for 115V oper ation. For 230V operation, re-connect the leads as shown in the diagram inside the motor junction box. The diagram is replicated on page 40 of this manual.

3. The 115V att achment plug suppl ied with t he band saw must be replaced with a UL/CSA listed plug suitable for 230V operation, similar to that shown in Figure 2. Contact your local Authorized JET Service Center or qualified el ectrician f or proper procedur es to install the plug. The band saw must com ply with all local and national codes after the 230V plug is install ed.

4. The band saw with a 230V plug should only be connected to an outlet having the same configuration (Figure 2). No adapter is

6.3 Extension cords

The use of an extension cord is not recommended f or this band saw; try t o positi on the machine wit hin reach of the power supply . If an extension cord is necessary, make sure the cord rati ng is suitabl e for t he amper age listed on the machine’s motor plate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.

Use the chart in Figure 3 as a general guide in choosing the correct size cord. If in doubt, use the next heav ier gauge. The smaller the gauge number, the heavier the cord.

Recomm end ed Ga ug es (A WG ) of Extensi on Co rd s

Extension Cord Length *

100

150

200

Amps

< 5 16 16 16 14 12 12

5 to 8 16 16 14 12 10 NR

8 to 12 14 14 12 10 NR NR 12 to 15 12 12 10 10 NR NR 15 to 20 10 10 10 NR NR NR 21 to 30 10 NR NR NR NR NR

*based on li miting th e lin e vol tage drop to 5V at 15 0% of the rated amp eres.

NR: Not Recommended.

feet

Figure 3

Note: Figures in this manual may or may not exactly match the appearance of your machine.

7.0 Unpacking

7.1 Contents of Shipping Contai ner

1 Band Saw 1 Table 1 Fence and Rail A ssembly 1 Resaw Guide and Knob 1 Miter Gauge 1 Upper Chip T r ay 1 Owner’s Manual 1 Warranty Card 1 Accessory Package Contains:

Hardware Bag

2 Knobs 1 Handle 1 10/12mm Wrench 2 Screws, 1/4-20x1/4” ( Upper Chip Tray )

Fence Hardwar e Bag

4 Socket Head Cap Screws, 5/16x 3/4” 4 Flat Washers, 5/16” 4 Lock Washers, 5/16”

Rail Hardware Bag

9 Hex Cap Screws, 1/4-20 x 5/8” 9 Flat Washers, 1/4” 9 Lock Washers, 1/4”

1. Remove the crate and packing material from the band saw except for the transport skid on the bottom.

2. Move the saw to its permanent working location. The site should be dry, well lit, and have enough room to handle long stock and the service or adjustm ent of the machine from any side.

3. Move the band saw off the skid.

4. Clean all rust protected surfaces with a mild solvent or kerosene and a soft cloth. Do not use lacquer thinner, paint thinner, or gasoline. These will damage painted surfaces.

5. For greater stability, the band saw can be secured to the floor with lag screws (not provided) t hr ough the four holes in the base.

Tools Required for Assembl y & Adj ustments

1 10mm Open End Wr enc h (provided) 2 14mm Open End Wr enc hes (not pr ov ided) 1 Cross Point S crew Driver (not provided) 1 Combinat ion Square (not provided) 1 6mm hex wrench (not pr ov ided)

8.0 Assembly

8.1 Handwheel

Attach the handle (A, Fig. 4) to the handwheel (B, Fig. 4) .

8.2 Mounting the Table

Important: The table is heavy. The assistance of a second person is strongly r ec om mended.

Referring to Fi gur es 5 and 6:

1. Remove the table insert (A) and tapered pin (B).

2. Slide the table so the saw blade (D) passes through the slot where the tapered pin (B) was located.

3. Rotate the table 90 degrees so that the miter slot (C) is parall el to the blade (D) and to the right of the blade when f acing the band saw as viewed in Figure 6.

4. Line up the table (H) to the trunnions so that the bolts (F ) feed through the support brac kets (E). Secur e the table wit h two lock knobs (G). Reinstall the table insert (A) and tapered pin (B).

8.3 Rail Assembly

Referring to Fi gur e 7:

1. Attach the front rail (J) to the cast iron table with two 1/4” x 5/8” hex cap screws, two 1/4” lock washers, and two 1/4” flat washers. The screws should be in approximately the center of the slot. Hand-tighten only at this time.

Figure 4

Figure 5

2. Attach the rear rail (K) to the table with two 1/4” x 5/8” hex cap screws, t wo 1/4” lock washers, and two 1/4” flat washers . Screws should be in approximately the center of the slot. Handtighten only at t his tim e.

3. Push the front and rear rails up as far as they will go.

4. Using a 10mm wrench, ti ghten the f our hex cap screws holding the front and rear rails to the table. Do not over -tighten the screws.

5. Attach the guide tube (L) to the front rail with five 1/4” x 5/8” hex cap screws, five 1/4” lock washers, and five 1/4” flat washers. Screws should be in approximately the center of the slot.

Only hand-tighten the guide tube at this time. You will be instructed to secure it later in the

Fence Assembly and Adjust m ent section.

Figure 6

Figure 7

8.4 Chip Tray

Referring to Fi gur e 8: Insert two 1/4” x 1/4” pan head screws through the

holes in the rear rail and into the table edge, leaving the screw heads protr uding slightly. Mount the chip tray onto t he screws as shown.

8.5 Dust Collection

If cu tti ng wood on the band saw, attach t he hose of a proper dust collection system to the 4” port at the rear of the band saw. NOTE: Dryer vent hose is not acceptable for this purpose.

If using the bandsaw for metal

working, DO NOT connect a dust collection system designed for wood dust. Hot metal shavings can pose a fi re risk.

8.6 Fence Assembly and Adjustment

Assembling the F enc e to F enc e Body

Referring to Fi gur e 9:

1. Attach the fence (A) to the fence body (B) wi th four 5/16” x 3/4” socket head cap screws (C), four 5/16” lock washers (D), and four 5/16” flat

washers (E). Hand-tighten only at thi s tim e.

Figure 8

Figure 9

Assembling the Rear Hook

Referring to Fi gur e 10:

2. Thread a 1/4"-20 hex nut (B) onto the pad’s

threaded stud (A) and insert through the fence (C) so the threaded stud is now inside

the fence.

3. Place the rear hook (D) on the threaded stud. Finish the assembly by placing a 1/4" flat

washer (E), 1/ 4" lock washer (F) and 1/4" hex nut (G) on the threaded stud, and finger

tighten. Note: Adjust for a gap of approximately 1/8"

between the pad (A) and hook (D) and as shown in the inset.

4. Tighten the assembly using two 10mm wrenches.

Figure 10

Fence Adjustm ent

5. Place the fence assembly onto the guide rail (D, Figure 11) and against the edge of the miter slot (C, Figure 11). The hook at the rear

of the fence should fit under the rear rail (see Figure 14).

The fence must ali gn parall el to t he miter slot along the entire l ength of the fence.

If adjustm ent is necessary:

6. Lock the fence by pushing down the lock handle (A, Figur e 11). Because the screws are only hand-tight , you can shift the fence slightly as needed until the fence is parallel to the miter slot.

7. When the fence has been properly aligned to the miter slot, t ighten t he four socket head cap screws (B, Figure 11) with a 6mm hex wrench. Make sure the fence remains parallel to the miter slot as you ti ghten the screws.

Note: This alignment will again be checked once the guide rail has been tightened.

Figure 11

8. Mov e the fence assembly to the other side of the blade as shown in Figure 12 so that the pointer (B, Fi gure 12) on the f ence body poi nts to zero on t he scale. Lock the f ence by pushing down the handle (A, Fi gur e 12) .

9. Move the guide rail (D, Figure 12) with the locked fence until the fence i s flush against the blade (C, Fi gur e 12). Do not unlock the fence to perform this. Move the fence and guide rail together when establ ishing the zero point.

Important: Do not force the fence into the blade so that the blade bends.

10. W ith a 10mm wrench, tighten t he five hex cap screws located on the bottom of the front rail that hold the guide rail to the front rail.

Note: After tightening the guide rail, double check that the f ence is still parallel to the miter slot. Make additional adjustments if needed.

Figure 12

Adjusting Clearance between Fence and Table

Referring to Fi gur es 13 and 14: Check the clearance between the table and the

fence. The fence should not rub against the table surface but be sli ghtly above it. Thi s gap should be the same at the front of t he table as it is at the rear.

If the gap between fence and table is not consistent, loosen either of the hex nuts on the hook (Figur e 14) and rot ate the sliding pad unt il the fence/tabl e gap is consistent ac ross the full l ength of the table. When this is achieved, tighten both hex nuts.

Check the adjustment of the hook at the rear of the fence. The hook should be positioned so that it overlaps the rear rail by approximately 1/8” (Figure 14). To adjust the hook, loosen the upper hex nut and slide the hook in or out as needed. Retighten upper hex nut.

8.7 Resaw Guide

For resawing attach t he post (A, Figure 15) to the fence with the lock knob (B, Figure 15). There is a slotted hole in the fence that will accommodat e the resaw kit. Position the post so that it is centered with the front edge of the blade. The resaw guide will give you a taller, single point contact surface during resawing.

Figure 13

Figure 14

8.8 Miter Gauge

1. Place the miter gauge i n the t able slot.

2. With a square verify the miter gauge face is square to the blade.

3. If the miter gauge is not square to the blade loosen the lock knob (C, Figure 15) and adj ust to the proper setti ng. Tighten the lock knob.

4. If the pointer is not at 90 degrees, loosen the screw (D, Figure 15) holding the pointer and move the pointer to 90 degrees.

5. Re-tighten the screw.

9.0 Adjustments

9.1 Table Tilt

1. Disconnect machine from power source.

2. Loosen the lock knobs (G, Figure 16).

3. Tilt t able up to 45 degrees to the r ight, or up t o 10 degrees to the left.

4. Tighten the lock knobs.

Figure 15

Note: Table stop bolt (F, Figure 16) must be removed to tilt table to the left.

Figure 16

+ 28 hidden pages