JET PT-1636JA, PT-2036JA, PT-2042JA, PT-2048JA, PT-2742JA Operating Instructions and Parts Manual
...
Operating Instructions and Parts Manual
PTJ-A Series Pallet Trucks
JET
427 New Sanford Road
LaVergne, Tennessee 37086 Part No. M-161003
Ph.: 800-274-6848 Edition 2 04/2020
www.jettools.com Copyright © 2019 JET
6
1.0 IMPORTANT SAFETY INSTRUCTIONS
WARNING – To reduce risk of injury:
Read and understand the entire owner’s manual before using the pallet truck.
Read and understand all warning and instruction labels on the truck.
Do not place hands or feet under the pallet truck at any time.
Do not operate a loaded pallet truck on ramps or inclines.
Do not tip load pallet truck forks. This may cause damage to the forks and personal injury if the rear of the
pallet truck suddenly “pops up.”
Never leave a loaded pallet truck unattended in the raised position. Always lower load to the floor.
Do not load pallet truck beyond its rated capacity.
Secure load before transporting.
To prevent accidental tipping, make sure load is centered on the forks.
Do not move a loaded pallet truck by other than manual force.
Do not transport persons with a pallet truck.
Failure to comply with these warnings may result in personal injury and/or property damage.
Replace warning labels if they become obscured or removed.
2
2.0 Table of contents
Section Page
1.0 IMPORTANT SAFETY INSTRUCTIONS ....................................................................................................... 2
2.0 Table of contents ............................................................................................................................................ 3
3.0 Introduction .................................................................................................................................................... 3
4.0 Specifications ................................................................................................................................................. 4
5.0 Assembly (for crate quantity purchases only) ................................................................................................ 5
6.0 Operation ....................................................................................................................................................... 6
7.0 Maintenance ................................................................................................................................................... 6
7.1 Lubrication .................................................................................................................................................. 6
7.2 Cleaning relief valve ................................................................................................................................... 6
7.3 Adjusting relief cam .................................................................................................................................... 6
7.4 O-Ring and seal replacements ................................................................................................................... 6
8.0 Troubleshooting PTJ-A Series Pallet Trucks ................................................................................................. 8
9.0 Replacement Parts ......................................................................................................................................... 8
9.1.1 PTJ-A Series Pallet Trucks – Exploded View .......................................................................................... 9
9.1.2 PTJ-A Series Pallet Trucks – Parts List ................................................................................................ 10
10.0 Warranty and Service ................................................................................................................................. 12
3.0 Introduction
Your JET Pallet Truck is designed with most efficient features for warehouse or dock.
The 2.56-inch lowered height, tapered fork tips and wide polyurethane entry/exit rollers combine for easy entry
and exit of pallets. The 180 turning radius allows maneuverability in confined spaces. Ball bearings on steer
and load wheels are lifetime lubricated, double-sealed, and promote smooth, quiet travel.
The cast iron pump features top-of-the-stroke and overload by-pass valve systems, and single point valve
service for easy replacement.
The chassis is heavy gauge steel, reinforced with cross-welded plates to prevent forks from bending; solid steel
push rods provide additional strength. Paint finish is powder-coated for superior protection of the underlying
steel.
In summary, your JET Pallet Truck is designed to offer consistent, long-term operation with minimal
maintenance and service attention. If there are questions or comments, please contact your local supplier or
JET. JET can also be reached at our web site: www.jettools.com.
Retain this manual for future reference. If the pallet truck transfers ownership, the manual should accompany it.
If there are questions or comments, please contact your local supplier or JET. JET can also be reached at our
web site: www.jettools.com.
Read and understand the entire contents of this manual before attempting assembly
or operation. Failure to comply may cause serious injury.
Register your product using the provided mail-in card, or register online:
http://www.jettools.com/us/en/service-and-support/warranty/registration/
3
4.0 Specifications
Table 1
Model number PT-1636JA PT-2036JA PT-2042JA PT-2048JA PT-2742JA
Stock number 161003 161004 161005 161006 161008
Load Capacity 5,500 lbs. (2495 kg.)
Turning Radius 180 deg.
Overall Fork Length L1 36 in. (914mm) 42 in. (1067mm) 48 in. (1219mm) 42 in. (1067mm) 48 in. (1219mm)
Overall Forks Width W1
Fork Width W2 6-1/4 in. (159 mm)
Lowered Height H2 2.56 in. (65 mm)
Maximum Height H1 6.69 in. (170 mm)
Number of Strokes to
Reach Maximum
Height
Force Required to
Pump at Maximum
Load
Steer Wheel Size
(Dia. x W)
Load Wheel Size
(Dia. x W)
Force Required to
Move Maximum Load
Overall Height C 45-1/8 in. (1146 mm)
Overall Length L2
Overall Width W1
Net Weight
Gross Weight
Pump Type Integrated
Pump
Housing
Materials
Forks Sheet steel, 11 ga. (3.2 mm)
Chassis Sheet steel, 11 ga. (3.2 mm)
Wheels Polyurethane
A
B 2-1/2 x 3-11/16 in. (63.5 x 94 mm
16 in.
(406mm)
16 in.
(406 mm)
118 lbs.
(53.5 kg)
129 lbs.
(58.5 kg)
51 in.
(1295 mm)
127 lbs.
(57.6 kg)
138 lbs.
(62.5 kg)
20-1/2 in. (521mm) 27 in. (686mm)
12
77 lbs. (35 kg)
7 x 2 in. (180 x 50.8 mm)
)
120 lbs. (54.5 kg)
57 in.
(1448 mm)
20-1/2 in. (521 mm) 27 in. (686 mm)
136 lbs.
(62 kg)
147 lbs.
(66.7 kg)
Cast
63 in.
(1600 mm)
138 lbs.
(62.6 kg)
149 lbs.
(67.6 kg)
Iron
57 in.
(1448 mm)
141 lbs.
(64 kg)
152 lbs.
(69 kg)
PT-2748JA
161009
63 in.
(1600 mm)
147 lbs.
(66.7 kg)
158 lbs.
(71.7 kg)
Figure 4-1
The specifications in this manual were current at the time this manual was published, but because of our policy of
continuous improvement, JET reserves the right to change specifications at any time and without prior notice, without
incurring obligations.
4
Loading...