Jet MBS-1014W Operating And Parts Manual

Download

Operating Instructions and Parts Manual

10 x 14 Horizontal Mitering Band Saw

Model MBS-1014W

WALTER M EIE R (Manuf a c turing) Inc.

1.0 Warranty and Service

JET, Wilton and Powermatic warrants every product they sell against manufacturers’ defects. If one of our tools needs service or repair, please contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday

Warranty Period The general warranty lasts for the time period specified in the literature included with your product or on the official JET, Wilton or Powermatic branded websites.

• JET, Wilton and Powermatic products carry a limited warranty which varies in duration based upon the product. (See chart below)

• Accessories carry a limited warranty of one year from the date of receipt.

• Consumable items are defined as expendable parts or accessories expected to become inoperable within a

reasonable amount of use and are covered by a 90 day limited warranty against manufacturer’s defects.

Who is Covered

This warranty covers only the initial purchaser of the product from the date of delivery.

What is Co vered

This warranty covers any defects in workmanship or materials subject to the limitations stated below. This warranty does not cover failures due directly or indirectly to misuse, abuse, negligence or accidents, normal wear-and-tear, improper repair, alterations or lack of maintenance.

Warranty Limitations

Woodworking products with a Five Year Warranty that are used for commercial or industrial purposes default to a Two Year Warranty. Please contact Technical Service at 1-800-274-6846 for further clarification.

How to Get Technical Support Please contact Technical Service by calling 1-800-274-6846. Please note that you will be asked to provide proof of initia l p u rch a s e whe n calling. If a product requires further inspection, the Technical Service representative will

explain and assist with any additional action needed. JET, Wilton and Powermatic have Authorized Service Centers located throughout the United States. For the name of an Authorized Service Center in your area call 1-800-274-6846 or use th e Service Cen ter Locator o n t he JET, Wilton or Power matic website.

More Informa tion

JET, Wilton and Powermatic are consistently adding new products. For complete, up-to-date product information, check with your local distributor or visit the JET, Wilton or Powermatic website.

How S tate Law Applies

This warranty gives you specific legal rights, subject to applicable state law.

Limitations on This Warranty

JET, WILTON AND POWERMATIC LIMIT ALL IMPLIED WARRANTIES TO THE PERIOD OF THE LIMITED WARRANTY FOR EACH PRODUCT. EXCEPT AS STATED HEREIN, ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE EXCLUDED. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. JET, WILTON AND POWERMATIC SHALL IN NO EVENT BE LIABLE FOR DEATH, INJURIES TO PERSONS OR PROPERTY, OR FOR INCIDENTAL, CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF OUR PRODUCTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. JET, Wilton and Powermatic sell through distributors only. The specifications listed in JET, Wilton and Powermatic printed materials and on official JET, Wilton and Powermatic-branded websites are given as general information and are not binding. JET, Wilton and Powermatic reserve the right to effect at any time, without prior notice, those alterations to parts, fittings, and accessory equipment which they may deem necessary for any reason whatsoever.

branded products are not sold in Canada by Walter Meier Manufacturing Americas.

JET

Product Listing with Warranty Period

90 Days – Parts; Consumable items; Light-Duty Air Tools 1 Year – Motors; Machine Accessories; Heavy-Duty Air Tools; Pro-Duty Air Tools 2 Year – Metalworking Machinery; Electric Hoists, Electric Hoist Accessories 5 Year – Woodworking Machinery Limited Lifetime – Wilton branded products; JET Parallel clamps; Manual Hoists; Manual Hoist Accessories; Shop Tools; Warehouse & Dock products; Hand Tools

NOTE: JET, Wilton and Powermatic are divisions of Walter Meier Manufacturing Americas. References in this document to JET, Wilton and/or Powermatic also apply to Walter Meier Manufacturing Americas or any of its successors in interest to the JET, Wilton and/or Powermatic brands.

2.0 Table of contents

Section Page

1.0 Warranty and Service ..................................................................................................................................... 2

2.0 Table of contents ............................................................................................................................................ 3

3.0 Warnings ........................................................................................................................................................ 4

4.0 About this manual .......................................................................................................................................... 5

5.0 Specifications ................................................................................................................................................. 5

6.0 Uncrating and Cleanup .................................................................................................................................. 6

7.0 Installation ...................................................................................................................................................... 6

8.0 Assembly ........................................................................................................................................................ 6

9.0 Electrical Connections .................................................................................................................................... 7

10.0 Controls ........................................................................................................................................................ 7

11.0 Prior to Operation ......................................................................................................................................... 7

12.0 Adjustments ................................................................................................................................................. 8

12.1 Adjusting vise square to blade ................................................................................................................. 8

12.2 Changing blade speeds ............................................................................................................................ 8

12.3 Adjusting feed rate ................................................................................................................................... 8

12.4 Changing blades ...................................................................................................................................... 8

12.5 Blade tracking adjustment ........................................................................................................................ 9

12.6 Automatic shut-off adjustment .................................................................................................................. 9

12.7 Thrust roller adjustment .......................................................................................................................... 10

12.8 Guide roller adjustment .......................................................................................................................... 10

12.9 Bow weight adjustment .......................................................................................................................... 10

12.10 Angle adjustment .................................................................................................................................. 11

12.11 Vise adjustment .................................................................................................................................... 11

13.0 Maintenance ............................................................................................................................................... 12

13.1 Lubrication .............................................................................................................................................. 12

14.0 Replacement Parts ..................................................................................................................................... 12

14.1.1 Base and Bed Assembly – Exploded View ......................................................................................... 13

14.1.2 Bow Assembly – Exploded View ......................................................................................................... 14

14.1.3 Parts List for MBS-1014W Band Saw ................................................................................................. 15

14.2.1 Gear Speed Reducer Assembly – Exploded View .............................................................................. 20

14.2.2 Gear Speed Reducer Assembly – Parts List ....................................................................................... 21

15.0 Electrical Connections ................................................................................................................................ 22

15.1.1 Electrical Connections – 1 Phase ........................................................................................................ 22

15.1.2 Electrical Panel Layout – 1 Phase ....................................................................................................... 22

15.2.1 Electrical Connections – 3 Phase ........................................................................................................ 23

15.2.2 Electrical Panel Layout – 3 Phase ....................................................................................................... 23

3.0 Warnings

1. Read and understand the e ntire instruction manual before attempting assembly or operation.

2. All JET bandsaws are designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper and safe operation of a bandsaw, do not use until proper training and knowledge have been obtained

3. Always wear approved safety glasses/face shields while using this machine. (Everyday eyeglasses only have impact resistant lenses; they are not safety glasses.)

4. Make certain the machine is properly grounded.

5. Before operating this machine, remove tie, rings, watches and other jewelry, and roll up sleeves past the elbows. Remove all loose clot hing and conf ine long hair. Do NOT wear gloves.

6. Keep the floor around the machine clean and free of scrap material, oil and grease.

7. Keep machine guards in place at all times when the machine is in use. If removed for maintenance purposes, use extreme caution and replace the guards immediately after completion of maintenance.

8. Do NOT over reach. Maintain a balanced stance at all times so that you do not fall or lean against blades or other moving parts.

9. Make all machine adjustments or maintenance with the machine unplugged from the power source.

10. Use the right tool. Do not force a tool or attachment to do a job for which it was not designed. The right tool will do the job better and more safely.

11. Replace warning labels if they become obscured or removed.

12. Make certain the switch is in t he OFF position before connecting the machine to the power supply.

13. Give your work undivided attention. Looking around, carrying on a conversation and “horseplay” are careless acts that can result in serious injury.

14. Keep visitors a safe distance from the work area.

15. Use recommended accessories; improper accessories may be hazardous.

16. Form a habit of checking to see that keys and adjusting wrenches are removed from the machine before turning it on.

17. Always keep hands a nd fingers away from the blade when the machine is running.

18. Never hand-hold the material. Always use the vise and clamp it securely.

19. Keep belt guard, blade guards, and wheel covers in place and in working order.

20. Always provide adequate support for lo ng and heavy material.

21. Use a sharp blade and keep machine clean for best and safest performance.

22. Failure to comply with all of these warnings may ca use serio u s i njury.

23. WARNING: Some dust created by power sanding, sawing, grinding, drilling and other construction activities contain chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• Lead from lead based paint.

•

Crystalline silica from bricks, cement and other masonry products.

•

Arsenic and chromium from chemically treated lumber.

Your risk of exposure varies, depending on how often you do this type of work. To reduce your exposure to these chemicals, work in a well-ventilated area and work with approved safety equipment, such as face or dust masks that are specifically designed to filter out microscopic particles.

Familiarize yourself with the following safety notices used in this manual:

This means that if preca utions are not heeded, it m ay result in minor injury a nd/or possible

machine damage.

This means that if precautions are not heeded, it may result in serious, or even fatal, injury.

4.0 About this manual

This manual is provided by Walter Meier (Manufacturing) Inc. covering the safe operation and maintenance procedures for a JET Model MBS-1014W Horizontal Saw. This manual contains instructions on installat io n, safety precautions, general operating procedures, maintenance instructions and parts breakdown. Your machine has been designed and constructed to provide years of tro uble-free operation if used i n accordance with the instructions as set forth in this document.

If there are questions or comments, please contact your local supplier or Walter Meier. Walter Meier can also be reached at our web site: www.waltermeier.com.

Retain this manual for future reference. If the machine transfers ownership, the manual should accompany it.

Read and understand the entire contents of this manual before attem pting assembly

or operation! Failure to comply may cause serious injury!

5.0 Specifications

Model number ...................................................... MBS-1014W-1....................................... MBS-1014W-3

Stock Number.................................................................. 414479.................................................. 414477

Capacity:

Round at 90° (in.) ................................................................. 10.......................................................... 10

Round at 45° (in.) ................................................................... 9............................................................ 9

Rectangle at 90° (in.) .................................................... 10 x 14................................................... 10 x 14

Rectangle at 45° (in.) .................................................. 9 x 8-1/2.................................................9 x 8-1/2

Blade Provided (i n.) .................................. 1 x 0. 035 x 130, 4/6VT........................... 1 x 0.035 x 130, 4/6VT

Blade Wheel Diameter (in.) ...................................................... 14.......................................................... 14

Blade Speeds (SFP M) ......................................82, 132, 210, 330................................... 82, 132, 210, 330

Motor .......................................................... 2HP, 1PH, 230V only.............................. 3HP, 3PH, 230/460V

(Prewired 230V)

Throat Depth (in.) .............................................................. 10-1/2.................................................... 1 0-1/2

Head Swivels......................................................................... 45°......................................................... 45°

Lowered Height (in.) ................................................................ 43.......................................................... 4 3

Raised Height (in.) ................................................................... 73.......................................................... 73

Bed Hei ght (in.) ....................................................................... 25.......................................................... 25

Floor Space Requi r ed (i n.) ............................................... 26 x 69................................................... 26 x 69

Net Weigh t (lb ) ...................................................................... 948........................................................ 948

Shipping Weigh t (lb) ............................................................ 1102...................................................... 1102

The specifications in this manual were current at time of publication, but because of our policy of continuous improvement, Walter Meier (Manufacturing) Inc., reserves the right to change specifications at any time and without prior notice, without incurring obligations.

6.0 Uncrating and Cleanup

NOTE: Read and understand the entire manual before attempting setup or operation.

1. Finish uncrating the saw and inspect for damage. Should any have occurred, contact your loc a l d i st ribut o r.

2. Remove all bolts attaching machine to shipping base.

3. Leave packing material between vice clamps and saw head intact until bandsaw has been lifted to its final position .

4. Clean all rust protected surfaces with kerosene or diesel oil to remove protective coating. Do not use gasoline, paint thinner, mineral spirit s, etc. These may damage painted surfaces.

5. Lubricate all slideway s with SAE 10W oil.

7.0 Installation

For best performance, the bandsaw should be locat e d on a solid a nd level fo u nda tion. A l lo w r oo m for servicing and f or m oving large stock around the bandsaw when deciding a location for the machine.

1. Using lifting straps that are isolated from the bandsaw’s finished surfaces, place machine in desired location. See Figure 1 for strap placement.

8.0 Assembly

1. Unbolt the motor assembly from the shipping crate bottom.

2. Remove nut (A, Figure 2) and washer (B, Figure 2) from the motor support shaft. Note: Picture shows motor already in place.

Figure 2

3. Remove shaft (C, Figure 2) from the motor mount bracket.

4. Carefully lift motor and line up holes in the motor mounting place and the motor bracket.

5. Slide motor support shaft into motor mount bracket to hold the motor in place.

6. Fasten shaft with nut and washer.

7. Loosen strain relief nut on the motor junction box. Remove the junction box cover. Insert wire though strain relief and wire to the terminal strip using the diagram on the junction box cover. Tighten the strain relief nut and replace the junction box cover.

8. Remove two hex cap bolts and washers (A, Figure 3) from the right side of the saw arm.

Figure 1

2. Install f our leveling bo lts with lock nuts o n bot h sides of the base as shown in the parts breakdown on page 13, items #2 and #3.

3. Place a level on the table surface and check side to side and front to back.

4. Adjust leveling screws until machine is level in both directions and tighten locking nuts.

Figure 3

9. Slide belt cover (B, Figure 3) around pulley shafts and attach to saw with two hex cap bolts and two washers.

10. Lift motor and place v-belt around both pulleys. Lower motor.

11. Tension the v-belt by pushing down on the motor and tightening the lock handle on the

motor tilt plate. Correct tension is achieved when finger pressure between the two pulleys causes approximately a 1/2” deflection.

Note: the pow er co rd end w ill have to be chang ed to one that is rated 460V when changing voltage.

12. Close pulley cover door and fasten with lock knob.

13. Fasten work stop rod (#241, page 13) to saw bed (11A) by inserting into bed and turning clockwise until tight. Place work stop bracket (#16) onto stop rod (241) and tighten lock handle (#20). Attach stop screw (#19) to stop bracket (#16) with lock handle (#18) and tighten.

9.0 Electrical Connections

All electrical connections

must be done by a qualified electrician. Failure to comply may result in serious injury.

Disconnect machine from the

power source before changing any voltage components. Failure to comply may cause serious injury.

The MBS-1014W bandsaw is rated at 3HP, 3 phase 230/460V, prewired 230V; or 2HP, single phase, 230V only. Confirm power available at t he saw’s location is the same as the saw is wired. To switch the MBS-1014W from 230V to 460V, the following item s will have to be changed:

10.0 Controls

See Figure 5. Power Indicator Light (A) – lit whenever machine

is running.

Start Button (B) – depress to start bandsaw. Emergency Stop Button (C) – depress to

immediately stop all machine functions. Coolant Switch (D) – turn arrow to “I” to turn on

flow of coolant. Turn arrow to “O” to stop flow of coolant.

Cutting Pressur e Control (E) – t urn clockwise to decrease cutting pressure. Turn counterclockwise to increase cutting pressure.

Hydraulic On-Off Valve (F) – turns hydraulic cylinder on and off.

• Main Motor – follow diagram inside

junction box cover.

• Coolant Pump – Remove access panel

on right side of saw, remove junction box cover on pump, and follow diagram inside junction box cover. See Figure 4.

Figure 4

• Control Transformer – Open electrical

panel on rear of base and switch primary wire on transformer from 230V to 460V.

Machine must always be correctly grounded.

Figure 5

11.0 Prior to Operation

1. Check that blade tooth direction matches diagram on blade guides.

2. Check to see that b lade is properly seated on wheels after applying correction tension (approximately 25,000 lbs.)

3. Set blade holder guides for approximately

0.003” to 0.005” clearance between t he guides and blade.

4. Check for slight clearance between back-up rollers and back of blade.

5. Position blade guides as close to work piece as possible.

6. Select proper speed a nd feed rate f or material being cut. See speed selection chart found in the enclosed “Guide to Bandsawing” booklet supplied with this saw.

7. Material to be cut must be securely held in vise.

8. Check to see that coolant level is adequate and turn on coolant pump if m aterial to be cut requires it. Machine should be filled with four gallons of the proper coolant mixture. Follow the directions on the product maker’s label and fill the coolant tank through the chip tray area.

9. Do not start cut on a sharp edge.

10. Keep machine lubricated. See “Lubrication” section.

Material chips or shavings are the best indicator of proper speed and pressure. The ideal chip is thin, tightly curled, and warm to the touch. Chips that range from golden brown to black indicate excessive force. Blue chips indicate e xtreme heat from too high a band speed which will shorten blade life. Thin or powdered chips indicate insufficient feed pressure.

12.4 Changing blades

12.0 Adjustments

12.1 Adjusting vise square to blade

1. Disconnect machine from power source.

2. Place a machinist’s square on the table against the blade and the vise. The square should lie along the entire length of the vise and blade without a gap.

3. If adjustment is necessary, loosen bolts holding the vise and adjust vise so square lines up p roper ly. Tighten bolts.

4. Connect machine to the power source.

12.2 Changing blade sp eeds

Disconnect the machine from

the power source before making any repair or adjustment. Failure to comply may cause serious injury.

1. Disconnect machine from power source.

2. Open pulley cover b y supporti ng the belt co ver with one hand while removing the belt cover lock knob with the other. Lower guard gently to its full open position.

Disconnect the machine from

the power source before making any repair or adjustment. Failure to comply may cause serious injury.

1. Disconnect machine from power source.

2. Raise saw arm approximately 6”. Hold saw arm in place by closing cutting pressure control valve.

3. Open both wheel covers and clean chips out of both wheel housings. Loosen two lock knobs below the control panel and remove upper blade guard.

4. Loose n set screw (A, Figure 6) and lower the blade cleaning brush.

3. Support motor with one hand while loosening lock handle. Lower motor gently.

4. Position belt in grooves according to the speed selection chart.

5. Tension the v-belt by pushing down on the motor and tightening the lock handle on the motor tilt plate. Correct tension is achieved when finger pressure on the belt between the two pulleys causes approximately 1/2" deflection.

6. Close pulley cover and fasten.

7. Connect machine to the power source.

12.3 Adjusting feed rate

Rate of feed is adjusted by turning the cutting pressure control knob on the control panel. Rate of feed is important to bandsaw performance, excessive pressure may break the blade or stall the saw. Insufficient pressure rapidly dulls the blade.

Figure 6

5. Release blade tension by turning blade tensioning handwheel (A, Figure 7) counterclockwise until blade is f ree.

Figure 7

6. Loosen lock knob (A, Figure 8) and slide left blade guide arm (B, Figure 8) to the right as far as possible.

accomplished by qualified personnel that are familiar with this type of adjustment and the dangers associated with it.

Figure 8

7. Rem ove old blade from both wheels and out of each blade guide.

Even dull blades are sharp to the skin. Use extra caution handling bandsaw blades.

8. Install new blade making sure teeth are pointed downward in the proper cutting direction. If necessary, turn blade inside out.

9. Position blade on band wheel s and tighten j ust enough to hold blade on wheels. Make sure back of blade rests lightly against the wheel flange of both wheels. Twist blade slightly to allow it to slip into guides.

1. Disconnect machine from power source.

2. Raise saw arm to its highest position and close cutting pressure control valve to hold saw arm in place.

3. Locate tracking adjustment plate on the back side of the driven blade wheel.

4. Loosen the three bolts (A, F ig ure 9) located on the top of the tracking nuts.

5. Tracking adjustment is accomplished by either loosening or tightening three adjusting nuts (B, Figure 9).

6. Tracking is set properly when the back of the blade lightly touches the wheel flange. Note: Over-tracking (allowing blade back to rub hard against wheel flange) will damage the blade wheels and blade.

7. Tighten locking bolts (A, Figure 9) once proper tracking is completed.

8. Connect machine to the power source.

10. Tension blade to appro ximately 25,000 lbs., as indicated on the blade tension indicator found on the tension wheel shaft housing.

11. Raise wire brush and tighten set screw to hold brush in place.

12. Close all covers and guards and fasten securely. Connect machine to power and run freely for approximately two minutes.

13. Turn power off and recheck blade tension and wire brush adjustment. If further adjustment is necessary, disconnect saw from power source, make adjustments, and reconnect to power.

12.5 Blade tracking adjustment

Blade tracking has been set at the factory and should require no adjustment. If a tracki ng problem occurs, adjust the machine as follows:

Tracking adjustment is done

with the wheel covers open to observe the blade. Use extreme caution so as not to come into contact with the blade.

Since tracking can only be adjusted while machi ne is running, it is suggested that this adjustment be

Figure 9

12.6 Automatic shut-off adjustment

The motor should shut off immediately after the blade has cut through the material and just before the head comes to rest on the horizontal stop bolt. If the machine continues to run after the work piece has been fully cut, locate and adjust the micro switch mounting plate down. If the machine s hut s off before the work piece has been completely cut, move the micro switch mounting plate up.

12.7 Thrust roller a djustment

1. Disconnect machine from power source.

2. Loosen two hex socket cap screws (A, Figure

10).

3. Move guide seat (B, Figure 10) up or down until a clearance of 0.003” to 0.005” between back of blade and thrust roller is obtained.

4. Tighten two he x socket cap screws (A , Figure

10).

5. Repeat for other blade guide assembly.

6. Connect machine to power source.

Figure 11

12.9 Bow weight adjustment

Bow weight is one of the most important adjustments of the saw. If the bow weight is not set properly, one can expect poor performance, crooked cuts, tooth stripping, stalling, and the blade popping off the blade wheels. They hydraulic feed rate unit will not com pensate for improper bow weight. Bow weight has been set at the factory and should not need any adjustment. If adjustment is necessary:

Figure 10

12.8 Guide roller adjustment

1. Disconnect machine from the power source.

2. Loosen blade guides (A, Figure 11) by loosening screws (B, Figure 10). Slide blade guides away from blade.

3. Loosen locking screws (C, Figure 11) by using a hex wrench.

4. Adjust the eccentric bushings with a combination wrench until the ball beari ngs are snug to the blade. Note: Blade should travel freely up and down between the ba ll bearings. Do not pinch the blade.

5. Tighte n locking screws (C, Figure 11).

6. Slide blade guides back into contact with blade and tighten screws (B, Figure 11).

7. Connect machine to the power source.

1. Disconnect the machine from the power source.

2. Turn on hydraulic valve (F, Figure 5).

3. Tur n cutting pressure contro l valve (E, Figure

5) counterclockwise until it stops.

4. Place one end of a fish-type scale under the blade tension handle and lift the saw with t he other end. Scale should indicate approximately 22-24 lbs.

5. Adjust tension to approximately 22-24 lbs. by turning the adjustable C-bolt found at the end of the coil spring on the rear of the bandsaw. See Figure 12.

6. Connect the machine to the power source.

Figure 12

12.10 Angle adjustment

To swivel the saw arm up to a 45° angle:

1. Disconnect the machine from the power source.

2. Pull the handle (A, Figure 13) toward the front of the saw.

3. Rotate the upper assembly to the desired angle.

4. Push the handle back toward the rear of the saw to lock the upper assembly.

1. Disconnect the machine from the power source.

2. Lower saw arm completely.

3. Pull the lock lever toward the front of the saw and push the saw arm assembly against the 45° stop.

4. Place a 45° angle sq uare on t he blade and the fixed vise jaw.

5. Loosen the lock nut (A, Figure 15).

6. Adjust the hex cap screw (B, Figure 15) until the blade is at a 90° angle to the fixed vise jaw.

7. Tighten the lock nut (A, Figure 15).

Figure 13

To adjust the 90° stop:

1. Disconnect the machine from the power source.

2. Lower saw arm completely.

3. Pull the lock lever toward the front of the saw and pull the saw arm assembly against the 90° stop.

4. Place a 90° square on the blade a nd the fixed vise jaw.

5. Loosen the lock nut (A, Figure 14).

6. Adjust the hex cap screw (B, Figure 14) until the blade is at a 90° angle to the fixed vise jaw.

7. Tighten the lock nut (A, Figure 14).

Figure 15

12.11 Vise adjustment

To position the movable vise jaw:

1. Turn vise handwheel 1/2 turn counter clockwise.

2. Move rack block (B, Figure 16) to desired location by sliding along the bed. Place the rack block onto the rack.

3. Tur n the handwheel to tighten th e vise.

Figure 14

To adjust the 45° stop:

Figure 16

To adjust the vise for angle cutting:

1. Loosen adjustable handle (index #219,221) to desire d lo c at ion.

2. Set the vise to desired angle, reinstall nuts and tighten the nut and bolt assemblies.

3. Adjust the movable vise parallel to the fixed vise by loosening bolt (A, Figure 17), adjusting to parallel, and tightening bolt.

Figure 17

13.0 Maintenance

Keep bandsaw and motor clean.

2. Open drain plug and allow lubricant to drain completely. Drain plug may be found on lower rear of gear case. Remove drain plug with a hex wrench.

3. Replace drain plug.

4. Remove filler cap (A, F igure 18) and fill gear box wit h 50 we ight gea r oil u ntil le vel rea ches dot in middle of sight glass.

5. Replace filler cap.

6. Connect machine to the power source.

Use a light machine oil to lubricate all other moving parts as needed.

13.1 Lubrication

All ball bearings are permanently lubricated and sealed. They require no further lubrication.

The gear box lubricant should be changed after the first 50 hours of operation. Change lubricant from then on every 250 hours of operation.

To check level of gear box lubricant, place saw arm in down position and allow a few minutes to pass so that oil drains down. Check level in sight glass on side of gear casing. Correct level is the dot in the middle of sight glass.

To change gear box lubricant:

1. Disconnect machine from power source.

14.0 Replacement Parts

Figure 18

Replacement parts are listed on the followi ng pages. To order parts or reach our service departm ent, call 1800-274-6848 Monday through Friday (see our website for business hours, www.jettools.com). Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately.

14.1.1 Base and Bed Assembly – Exploded View

14.1.2 Bow Assembly – Exploded View

14.1.3 Parts List for MBS-1014W Band Saw

Index No Part No Description Size Qty

1A .............. MBS1014W-1A ......... Base......................................................................... ...................................... 1

2 ................ Ts-1492071 ............... Hex Cap Bolt............................................................ M12x 70 ......................... 4

3 ................ TS-1540081 .............. Hex Nut .................................................................... M12 ............................... 4

4 ................ HBS916W-CP ........... Coolant Pump (1PH)................................................ ...................................... 1

.................. MBS1014W-CP ......... Coolant Pump (3PH)................................................ ...................................... 1

5 ................ TS-15311051 ............ Pan Head Screw ...................................................... M6x16 ........................... 2

8 ................ HBS916W-08 ............ Hose ........................................................................ ...................................... 1

9 ................ HBS916W-09 ............ Coolant Gauge......................................................... ...................................... 1

9-1 ............. TS-1491041 .............. Hex Cap Bolt............................................................ M10x30 ......................... 2

11A ............ MBS1014W-11A ....... Bed .......................................................................... ...................................... 1

11B ............ MBS1014W-11B ....... Bed (s/n 01021646 and lower)................................. ...................................... 1

11BN ......... MBS1014W-11BN ..... Bed (s/n 01021647 and higher) ............................... ...................................... 1

15 .............. HBS916 W-16 ............ Stop Bracket ............................................................ ...................................... 1

18 .............. HBS916 W-18 ............ Lock Handle ............................................................. ...................................... 1

19 .............. HBS916W-19 ............ Work Stop ................................................................ ...................................... 1

20 .............. HBS916 W-20 ............ Lock Knob ................................................................ ...................................... 1

21 .............. HBS1018 W-21 .......... Handwheel Assembly .............................................. ...................................... 1

22 .............. HBS1018W-22 .......... Lead Screw Seat ..................................................... ...................................... 1

23 .............. TS-1490051 .............. Hex Cap Bolt............................................................ M8x30 ........................... 4

23-1 ........... TS-1551061 .............. Lock Washer ............................................................ M8 ................................. 2

24A ............ MBS1014W-24A ....... Lead Screw (s/n 01021646 and lower) .................... 780mm .......................... 1

24AN ......... MBS1014W-24AN ..... Lead Screw (s/n 01021647 and higher)................... 530mm .......................... 1

25 .............. HBS916W-25 ............ Lead Screw Bracket (s/n 903358 and lower) ........... ...................................... 1

26 .............. HBS916W-26 ............ Acme Nut (Re:HBS916W-26A)(s/n 903358 and lower) .................................. 1

.................. HBS916W-26A .......... Acme Nut Assembly (inc. 26,27,28,29)(s/n 903358 and lower)...................... 1

27 .............. HBS916W-27 ............ Button (Re:HBS916W-26A)(s/n 903358 and lower) ...................................... 1

28 .............. HBS916W-28 ............ Retain er (Re:HBS916W-26A)(s/n 903358 and lower) .................................... 2

29 .............. HBS916W-29 ............ Pan Head Screw (Re:HBS916W-26A)(s/n 903358 and low er)....................... 1

30 .............. HK-2516-2RS ............ Needle Bearing ........................................................ ...................................... 2

31 .............. HBS1018W-31 .......... Torsion Spring ......................................................... ...................................... 1

32 .............. HBS916W-32 ............ Pivo t Shaft ............................................................... ...................................... 1

32-1 ........... TS-1550041 .............. Washer .................................................................... M12 ............................... 2

32-2 ........... HBS916 W-32-2 ......... Bolt w/ Zerk Fitting ................................................... ...................................... 2

33 .............. HBS1018 W-33 .......... Pivot Bracket............................................................ ...................................... 1

34 .............. TS-1540081 .............. Nut ........................................................................... M12 ............................... 1

35 .............. TS-1550081 .............. Washer .................................................................... 12mm ............................ 1

36 .............. TS-1492041 .............. Hex Cap Bolt............................................................ M12x40 ......................... 1

37 .............. HBS916W-37 ............ Torsion Spring Shaft ................................................ ...................................... 1

38 .............. HBS916W-38 ............ C-Ri ng...................................................................... S-22 .............................. 1

39 .............. TS-1490041 .............. Hex Cap Bolt............................................................ M8x25 ........................... 1

40 .............. HBS1018W-40 .......... Motor Tilt Plate......................................................... ...................................... 1

41 .............. HBS916W-41 ............ Limit Switch Plate .................................................... ...................................... 1

42 .............. TS-1550061 .............. Washer .................................................................... 8mm .............................. 2

43 .............. TS-1490031 .............. Hex Cap Bolt............................................................ M8x20 ........................... 2

44 .............. TS-1482021 .............. Hex Cap Screw ........................................................ M6x12 ........................... 6

45 .............. HBS916 W-45 ............ Limit Switch.............................................................. ...................................... 1

47 .............. HBS1018W-47A ........ Cylinder Pin ............................................................. ...................................... 1

48 .............. HBS916W-48 ............ C-Ri ng...................................................................... S-20 .............................. 1

49 .............. HBS916W-49 ............ C-Ri ng...................................................................... S-25 .............................. 2

51 .............. HBS1018W-51 .......... Hydraulic Cylinder Assembly ................................... ...................................... 1

52 .............. HBS916W-52 ............ Cylin der Pin ............................................................. ...................................... 1

53 .............. HBS1018W-53 .......... Hydrauli c Mounting Plate - Top ............................... ...................................... 1

53-1 ........... TS-1551071 .............. Lock Washer ............................................................ 10mm ............................ 4

53-2 ........... TS-1491041 .............. Hex Cap Bolt............................................................ M10x30 ......................... 2

54 .............. TS-1492051 .............. Hex Cap Bolt............................................................ M12x50 ......................... 2

55 .............. TS-1550081 .............. Washer .................................................................... 12mm ............................ 2

56 .............. HBS916W-56 ............ Plate......................................................................... ...................................... 1

57 .............. TS-0561051 .............. Hex Nut .................................................................... 1/2" ................................ 2

58 .............. HBS916 W-58 ............ Spring Bracket ......................................................... ...................................... 1

59 .............. HBS916W-59 ............ Adjustable C-Bolt ..................................................... ...................................... 1

Index No Part No Description Size Qty

60 .............. HBS1018W-60 .......... Spri ng ...................................................................... ...................................... 1

62 .............. TS-1492041 .............. Hex Cap Bolt............................................................ M12x40 ......................... 2

63-1 ........... TS-1551081 .............. Lock Washer (s/n 0202755 and lower) .................... 12mm ............................ 6

.................. TS-1551081 .............. Lock Washer (s/n 0202756 and higher)................... 12mm ............................ 2

65 .............. HBS916W-64 ............ Vise Jaw – left.......................................................... ...................................... 1

65-1 ........... MBS1014 W-65-1....... Extension Plate ........................................................ ...................................... 1

65-2 ........... MBS1014 W-65-2....... Hex Socket Cap Screw ............................................ ...................................... 2

65-3 ........... MBS1014 W-65-3....... Lock Washer ............................................................ ...................................... 2

69 .............. TS-1503011 .............. Hex Socket Cap Bolt ............................................... M6x8 ............................. 8

70 .............. HBS916W-70 ............ Electrical Panel Cover ............................................. ...................................... 1

71 .............. HBS916W-71 ............ Fuse Block ............................................................... ...................................... 2

72 .............. HBS1018W-72 .......... Magnetic Switch (1PH) ............................................ ...................................... 1

.................. MBS1014W-72 .......... Magnetic Switch (3PH) ............................................ ...................................... 1

73 .............. HBS1018W-73 .......... Transformer (1PH) ................................................... ...................................... 1

.................. MBS1014W-73 .......... Transformer (3PH) ................................................... ...................................... 1

74 .............. HBS916W-74 ............ Transformer Strip ..................................................... ...................................... 1

75 .............. HBS916W-75 ............ Handl e ..................................................................... ...................................... 1

76 .............. TS-1534051 .............. Pan Head Screw ...................................................... M6x16 ........................... 4

77 .............. TS-1482021 .............. Hex Cap Bolt............................................................ M6x12 ........................... 2

77-1 ........... TS-1551041 .............. Lock Washer ............................................................ M6 ................................. 2

77-2 ........... TS-1550041 .............. Washer .................................................................... M6 ................................. 2

78 .............. HBS916W-78 ............ Wire Brush Guard .................................................... ...................................... 1

79 .............. TS-1503011 .............. Hex Socket Cap Screw ............................................ M6x8 ........................... 12

.................. HBS1018W-79A ........ Adjustable Bracket Mount - rear (HBS-1018W only; not shown) .................... 1

80 .............. HBS1018W-80A ........ Blade Wheel Cover - right........................................ ...................................... 1

81 .............. TS-1550041 .............. Washer .................................................................... M6 ................................. 4

82 .............. HBS916 W-82 ............ Bushing .................................................................... ...................................... 1

83 .............. HBS916W-83 ............ Wash er .................................................................... ...................................... 1

84 .............. MBS1018W-84 .......... Drive Wheel ............................................................. ...................................... 1

85 .............. .................................. Blade (local purchase) ............................................. ...................................... 1

86 .............. HBS916W-86 ............ Hose ........................................................................ ...................................... 1

87 .............. TS-1533031 .............. Pan Head Screw ...................................................... M5x10 ........................... 2

88 .............. HBS916W-88 ............ Filter Screen ............................................................ ...................................... 1

89 .............. TS-1492031 .............. Hex Cap Bolt............................................................ M12x35 ......................... 5

89-1 ........... TS-1551081 .............. Lock Washer ............................................................ 12mm ............................ 4

90 .............. HBS916 W-90 ............ Lock Knob ................................................................ ...................................... 4

92 .............. HBS1018W-92 .......... Blade Wheel Box - right ........................................... ...................................... 1

93 .............. HBS1018W-93 .......... Connector ................................................................ .......... ............................ 1

94 .............. HBS1018W-94 .......... Gear Box Assembly (can only order entire assembly).................................... 1

95 .............. HBS916W-95 ............ Key ........................................................................... 7mm .............................. 1

96 .............. HBS1018W-96 .......... Pulley Cover ............................................................ ...................................... 1

96-1 ........... HBS916 W-96-1 ......... Lock Knob ................................................................ ...................................... 1

97 .............. HBS1018W-97 .......... Gear Box Pulley ....................................................... ...................................... 1

98 .............. VB-A37 ...................... V-Belt ....................................................................... ...................................... 1

99 .............. HBS1018W-99 .......... Motor Pulley ............................................................. ...................................... 1

100 ............ TS-1482031 .............. Hex Cap Bolt............................................................ M8x16 ........................... 4

100-1 ......... TS-1550061 .............. Washer .................................................................... M8 ................................. 2

100-2 ......... TS-1551061 .............. Lock Washer ............................................................ M8 ................................. 2

101 ............ HBS916W-101 .......... Hos e ........................................................................ ...................................... 1

101-1 ......... HBS916W-101-1 ....... Hose ........................................................................ ...................................... 1

102 ............ HBS916W-102 .......... Support Shaft ........................................................... ...................................... 1

102-1 ......... TS-1550081 .............. Washer .................................................................... M12 ............................... 1

102-2 ......... TS-1540081 .............. Hex Nut .................................................................... M12 ............................... 1

103 ............ TS-1492021 .............. Hex Cap Bolt (S/N 0202755 and lower)................... M12 x30 ......................... 5

.................. TS-1492021 .............. Hex Cap Bolt (S/N 0202756 and higher) ................. M12x30 ......................... 1

104 ............ HBS916W-104 .......... Motor Moun t Bracket ............................................... ...................................... 1

105 ............ HBS1018W-105A ...... Column .................................................................... ...................................... 1

106 ............ TS-1506011 .............. Hex Socket Cap Screw ............................................ M12x 20 ......................... 6

107 ............ HBS916W-107 .......... Locking Handle ........................................................ ...................................... 1

108 ............ TS-1550061 .............. Washer .................................................................... 8mm .............................. 1

109 ............ TS-1490081 .............. Hex Cap Bolt............................................................ M8x45 ........................... 4

109-1 ......... TS-1550061 .............. Washer .................................................................... M8 ................................. 4

Index No Part No Description Size Qty

110 ............ HBS916W-110 .......... Motor Mount Pl ate ................................................... ...................................... 1

111 ............ HBS1018W-111 ........ Motor........................................................................ 2HP, 1PH, 230V only .... 1

.................. MBS1014W-111 ........ Motor........................................................................ 3HP, 3PH, 230/460V..... 1

.................. HBS1018W-111A ...... Capacitor (not shown).............................................. 400MFD, 125VAC ......... 1

.................. HBS1018W-111B ...... Capacitor Cover (not shown) ................................... ...................................... 1

112 ............ TS-1550061 .............. Washer .................................................................... M8 ................................. 4

112-1 ......... TS-1551061 .............. Lock Washer ............................................................ M8 ................................. 4

113 ............ TS-1540061 .............. Hex Nut .................................................................... M8 ................................. 4

114 ............ HBS916W-114 .......... Key ........................................................................... 7mm .............................. 1

115 ............ TS-1550081 .............. Washer .................................................................... M12 ............................... 1

116 ............ TS-1504041 .............. Hex Socket Cap Screw ............................................ M8x20 ........................... 1

117 ............ HBS1018W-117A ...... Blade Wheel Cover - left .......................................... ...................................... 1

118 ............ BB-608VV ................. Ball Bearing ............................................................. ...................................... 2

119 ............ TS-1492011 .............. Hex Cap Bolt............................................................ M12x25 ......................... 2

120 ............ TS-1550081 .............. Washer .................................................................... M12 ............................... 1

121 ............ BB-6205Z .................. Ball Bearing ............................................................. ...................................... 3

122 ............ MBS1014W-122 ........ Idler Wheel............................................................... ...................................... 1

123 ............ HBS1018W-123A ...... Blade Guard............................................................. ...................................... 1

123-1 ......... TS-1550061 .............. Washer .................................................................... M8 ................................. 1

123-2 ......... TS-1551061 .............. Lock Washer ............................................................ M8 ................................. 1

123-3 ......... TS-1490021 .............. Hex Cap Bolt............................................................ M8x16 ........................... 1

124 ............ HBS916W-124 .......... Guide Bracket - left .................................................. ...................................... 1

.................. HBS916W-124A ........ Guide Bracket Assembly - left ................................. ...................................... 1

124-1 ......... TS-1504031 .............. Hex Socket Cap Screw ............................................ M8x16 ........................... 6

125 ............ TS-1540061 .............. Washer .................................................................... M8 ................................. 4

126 ............ BB-6201VV ............... Ball Bearin g ............................................................. ...................................... 8

127 ............ HBS916W-127 .......... Eccentric Sleeve (outside) ....................................... ...................................... 2

127-1 ......... HBS1018W-127-1 ..... Sleeve ( inside, not shown)....................................... ...................................... 2

128 ............ TS-1551061 .............. Lock Washer ............................................................ M8 ................................. 4

129 ............ TS-1504091 .............. Hex Socket Cap Screw ............................................ M8x45 ........................... 4

130 ............ TS-1503071 .............. Hex Socket Cap Screw ............................................ M6x30 ........................... 4

130-1 ......... TS-1550041 .............. Washer .................................................................... M6 ................................. 8

131 ............ HBS916W-131 .......... Blade Guide ............................................................. ...................................... 4

132 ............ TS-1504081 .............. Hex Socket Cap Screw ............................................ M8x40 ........................... 4

133 ............ TS-1551081 .............. Lock Washer ............................................................ M8 ................................. 4

133-1 ......... TS-1550081 .............. Washer (HBS-916W) ............................................... M8 ................................. 4

134 ............ HBS1018W-134A ...... Adjustable Bracket ................................................... ...................................... 1

135 ............ HBS1018W-135 ........ Scale ........................................................................ ...................................... 1

136 ............ TS-1505031 .............. Hex Socket Cap Screw ............................................ M10x 25 ......................... 2

137 ............ HBS1018W-137 ........ Slide ......................................................................... ...................................... 1

138 ............ HBS1018W-138 ........ Blade Bracket - left .................................................. ...................................... 1

139 ............ TS-1492021 .............. Hex Cap Bolt............................................................ M12x30 ......................... 4

139-1 ......... TS-1551081 .............. Lock Washer ............................................................ M12 ............................... 4

141 ............ MBS1014W-141 ........ Knob ........................................................................ ...................................... 2

143 ............ TS-1524021 .............. Set Screw ................................................................ M8x10 ........................... 4

144 ............ HBS1018W-144 ........ Blade Bracket - right ................................................ ...................................... 1

145 ............ TS-1482011 .............. Hex Cap Bolt............................................................ M6x10 ........................... 1

146 ............ TS-1550041 .............. Washer .................................................................... M6 ................................. 1

147 ............ HBS916W-147 .......... Wire Brush ............................................................... ...................................... 1

148 ............ HBS916W-148 .......... Wire Brush Rod ....................................................... ...................................... 1

149 ............ HBS1018W-149 ........ Guide Bracket - right ................................................ ...................................... 1

.................. HBS1018W-149A ...... Guide Bracket Assembly - right ............................... ...................................... 1

150 ............ HBS916W-150 .......... Spri ng ...................................................................... ...................................... 1

152 ............ TS-1540071 .............. Hex Nut .................................................................... M10 ............................... 2

154 ............ HBS1018W-154A ...... Adjustable Bracket - right......................................... ...................................... 1

155 ............ TS-1540081 .............. Hex Nut .................................................................... M12 ............................... 1

156 ............ MBS1014W-156 ........ Hex Cap Bolt with Rubber Stopper .......................... M12x60 ......................... 1

157 ............ HBS1018W-157A ...... Blade Guard............................................................. ...................................... 1

157-1 ......... HBS1018W-157-1 ..... Blade Guard - down ................................................. ...................................... 1

Index No Part No Description Size Qty

158 ............ HBS916W-158 .......... Lock Knob ................................................................ ...................................... 2

159 ............ TS-1523021 .............. Set Screw ................................................................ M6x8 ............................. 1

160 ............ HBS916W-160 .......... Adjusting Valve ........................................................ ...................................... 2

160-1 ......... HBS916W-160-1 ....... Clamp ...................................................................... ...................................... 2

160-2 ......... TS-1551041 .............. Lock Washer ............................................................ M6 ................................. 4

160-3 ......... TS-1482021 .............. Hex Cap Bolt............................................................ M6x12 ........................... 4

161 ............ HBS916W-161 .......... Power Indicator Light ............................................... ...................................... 1

162 ............ HBS916 W-162 .......... Start Switch.............................................................. ...................................... 1

163 ............ HBS916W-163 .......... Stop Switch .............................................................. ...................................... 1

164 ............ HBS916 W-164 .......... Pump Switch ............................................................ ...................................... 1

165 ............ HBS916W-165S ........ Feed Control – On/Off Valve (S/N 912484 and l ower 1014W) ....................... 1

.................. HBS916W-165S-1..... Speed Control – On/Off Valve (S/N 912484 and lower 1014W) ..................... 1

.................. HBS916W-165SP ..... Plate (n ot shown)(S/N 912484 and low er 1014W) .. ...................................... 1

165N .......... HBS916W-165N........ Feed Con trol - On/Off Valve (S/N 912485 and higher 1014W) ..................... 1

.................. HBS916W-165N-1 .... Plate (not shown)(S/N 912485 and higher 1014W) . ...................................... 1

166 ............ HBS916W-166 .......... Connecting Tube ..................................................... ...................................... 1

166-1 ......... HBS916 W-166-1 ....... Hose Clamp ............................................................. ...................................... 3

168 ............ HBS916W-168 .......... Control Box .............................................................. ...................................... 1

169 ............ HBS916W-169 .......... Control Panel ........................................................... ...................................... 1

170 ............ TS-1533031 .............. Pan Head Screw ...................................................... M5x10 ........................... 6

171 ............ HBS1018W-171 ........ Wheel Box - left ....................................................... ...................................... 1

172 ............ HBS916W-172 .......... Han dle ..................................................................... ...................................... 1

173 ............ TS-1540081 .............. Hex Nut .................................................................... M12 ............................... 2

175 ............ TS-1533031 .............. Pan Head Screw ...................................................... M5x10 ........................... 2

176 ............ HBS916W-176 .......... Indicator Scale ......................................................... ...................................... 1

177 ............ HBS916W-177 .......... Slide Bracket............................................................ ...................................... 1

178 ............ HBS916W-178 .......... Tension Shaft........................................................... ...................................... 1

179 ............ HBS916W-179 .......... Key ........................................................................... 5mm .............................. 1

180 ............ HBS916W-180 .......... Handwheel ............................................................... ...................................... 1

181 ............ HBS916W-181 .......... Lock Washer ............................................................ M22 ............................. 13

182 ............ HBS916W-182 .......... Flat Steel Washer .................................................... ...................................... 1

183 ............ HBS916W-183 .......... Tension Ind icator ..................................................... ...................................... 1

184 ............ BB-51104 .................. Thrus t Bearing ......................................................... ...................................... 1

187 ............ HBS916W-187 .......... Sli de ......................................................................... ...................................... 1

188 ............ TS-1524021 .............. Set Screw ................................................................ M8x10 ........................... 2

189 ............ HBS916W-189 .......... Ex tension Bar .......................................................... ...................................... 1

190 ............ HBS916W-190 .......... Wheel Sh aft ............................................................. ...................................... 1

191 ............ TS-1540081 .............. Hex Nut .................................................................... M12 ............................... 1

191-1 ......... TS-1523021 .............. Set Screw ................................................................ M6x8 ............................. 3

192 ............ TS-1504051 .............. Hex Socket Cap Screw ............................................ M8x25 ........................... 4

192N .......... TS-1503021 .............. Hex Socket Cap Screw ............................................ M6x12 ........................... 2

193 ............ TS-1492011 .............. Hex Socket Cap Screw ............................................ M12x 25 ......................... 1

194 ............ HBS916W-194 .......... Gib ........................................................................... ...................................... 2

195 ............ HBS916W-195 .......... Hex Cap Screw (re: HBS916W-196) ....................... ...................................... 3

196 ............ HBS916W-196 .......... Screw Assembly ...................................................... ................ ...................... 3

196-1 ......... HBS916 W-196-1 ....... Lock Washer (re: HBS916W-196) ........................... ...................................... 3

197 ............ HBS916 W-197 .......... Hose Fitting.............................................................. ...................................... 1

198 ............ HBS916W-198 .......... Hose Clamp ............................................................. ...................................... 1

199 ............ HBS916W-199 .......... Hose Clamp ............................................................. ...................................... 1

202 ............ HBS916W-202 .......... Power Cord .............................................................. 1 PH .............................. 1

.................. MBS1014W-202 ........ Power Cord .............................................................. 3 PH .............................. 1

206 ............ HBS916W-206 .......... Speed Chart Label ................................................... ...................................... 1

207 ............ HBS916W-207 .......... Hos e ........................................................................ ...................................... 1

208 ............ HBS916W-208 .......... Hos e ........................................................................ ...................................... 1

213 ............ TS-1550071 .............. Washer .................................................................... M10 ............................... 5

214 ............ HBS1018W-214 ........ Clamp ...................................................................... ...................................... 2

215 ............ HBS1018W-215 ........ Connector ................................................................ ............ .......................... 2

216 ............ MBS1014W-216 ........ Fixed Vise Jaw......................................................... ...................................... 1

217 ............ MBS1014W-217 ........ Cotter Pin ................................................................. ...................................... 1

218 ............ MBS1014W-218 ........ Spring Cover ............................................................ ...................................... 1

219 ............ MBS1014W-219 ........ Adjustable Handle.................................................... ...................................... 1

220 ............ MBS1014W-220 ........ Support (S/N 0202755 and lower) ........................... ...................................... 1

Index No Part No Description Size Qty

220A .......... MBS1014W-220A ..... Support (S/N 0202756 and higher) .......................... ...................................... 1

221 ............ MBS1014W-221 ........ Adjustable Handle.................................................... ...................................... 1

222 ............ MBS1014W-222 ........ Bracket..................................................................... ...................................... 1

223 ............ MBS1014W-223 ........ Bracket..................................................................... ...................................... 1

224 ............ MBS1014W-224 ........ Slide ......................................................................... ...................................... 1

225 ............ MBS1014W-225 ........ Guide Plate .............................................................. ...................................... 1

226 ............ MBS1014W-226 ........ Turning Slide............................................................ ...................................... 1

226A .......... MBS1014W-226A ..... Scale ........................................................................ ...................................... 1

227 ............ MBS1014W-227 ........ Bracket..................................................................... ...................................... 1

228 ............ BB-51106 .................. Thrust Bearing (S/N 0202755 and lower) ................ ...................................... 1

229 ............ MBS1014W-229 ........ Center Fixed Bracket (S/N 0202755 and lower) ...... ...................................... 1

230 ............ MBS1014W-230 ........ Turning Slide Bracket (S/N 0202755 and lo wer) ..... ...................................... 1

231 ............ MBS1014W-231 ........ Turning Slide (S/N 0202755 and lower)................... ...................................... 1

231A .......... MBS1014W-231A ..... Turning Slide (S/N 0202756 and higher) ................. ...................................... 1

232 ............ MBS1014W-232 ........ Turn Plate ................................................................ ...................................... 1

233 ............ MBS1014W-233 ........ Coolant Pump Bracket ............................................. ...................................... 1

234 ............ TS-1491061 .............. Hex Cap Bolt............................................................ M10x40 ......................... 3

235 ............ TS-1482041 .............. Hex Socket Cap Screw ............................................ M6x20 ........................... 6

236 ............ MBS1014W-236 ........ Washer .................................................................... ...................................... 1

237 ............ MBS1014W-237 ........ Lock Knob ................................................................ ...................................... 1

238 ............ MBS1014W-238 ........ Brass Fitting ............................................................. ...................................... 2

239 ............ TS-1524041 .............. Set Screw ................................................................ M8x16 ........................... 1

240 ............ TS-1550101 .............. Washer .................................................................... M16 ............................... 2

241 ............ MBS1014W-241 ........ Stop Rod .................................................................. ...................................... 1

242 ............ MBS1014W-242 ........ Panel Cover ............................................................. ...................................... 1

243 ............ TS-1491031 .............. Hex Cap Bolt............................................................ ...................................... 2

244 ............ MBS1014W-244 ........ ID Label, Warning Label (not shown) ...................... ...................................... 1

245 ............ MBS1014W-245 ........ Slide Bracket (S/N 01021646 and lower)................. ...................................... 1

245N .......... MBS1014W-245N ..... Slide Bracket (S/N 01021647 and higher) ............... ...................................... 1

246 ............ MBS1014W-246 ........ Lead Screw Bracket (S/N 01021646 and lower)...... ...................................... 1

246N .......... MBS1014W-246N ..... Lead Screw Bracket (S/N 01021647 and hi gher) .... ...................................... 1

247 ............ MBS1014W-247 ........ Rack Block (S/N 01021646 and lower) .................... ...................................... 1

247N .......... MBS1014W-247N ..... Rack Block (S/N 01021647 and higher) .................. ...................................... 1

248 ............ MBS1014W-248 ........ Rack (S/N 01021646 and lower).............................. ...................................... 1

248N .......... MBS1014W-248N ..... Rack (S/N 01021647 and higher) ............................ ...................................... 1

248N-1 ...... MBS1014W-248N-1 .. Bushing .................................................................... ...................................... 1

248N-2 ...... TS-1503041 .............. Hex Socket Cap Screw ............................................ M6x25 ........................... 1

248N-3 ...... TS-1551041 .............. Lock Washer ............................................................ M6 ................................. 1

249 ............ MBS1014W-249 ........ Pin............................................................................ ...................................... 1

250 ............ MBS1014W-250 ........ Pin............................................................................ 4x16 .............................. 1

14.2.1 Gear Speed Reducer Assembly – Exploded View

14.2.2 Gear Speed Reducer Assembly – Parts List

Index No Part No Description Size Qty

1 ................ HBS916W-94-01 ....... Oil Seal .................................................................... 35x55x8 mm ................. 1

2 ................ BB-30207 .................. Bearing .................................................................... 30207 ............................ 1

3 ................ BB-6207 .................... Bearing .................................................................... 6207 .............................. 1

4 ................ HBS916W-94-04 ....... Shaft ........................................................................ ...................................... 1

5 ................ HBS916W-94-05 ....... Key........................................................................... 8x7x30 mm ................... 1

6 ................ HBS916W-94-06 ....... Gear Wheel.............................................................. ...................................... 1

7 ................ HBS916W-94-07 ....... Bearing .................................................................... 6206 .............................. 1

8 ................ HBS916W-94-08 ....... Output Shaft Cover .................................................. ...................................... 1

9 ................ HBS916W-94-09 ....... Output Hex Cap Screw ............................................ M10x20 ......................... 4

10 .............. HBS916W-94-10 ....... Input Hex Cap Screw ............................................... M8x20 ........................... 4

11 .............. HBS916W-94-11 ....... Input Shaft Cover ..................................................... ...................................... 1

12 .............. HBS916W-94-12 ....... Washer .................................................................... ...................................... 1

13 .............. BB-6025 .................... Bearing .................................................................... 6025 .............................. 1

14 .............. HBS916W-94-14 ....... Input Shaft ............................................................... ...................................... 1

15 .............. HBS916W-94-15 ....... Key........................................................................... 7x7x60 mm ................... 1

16 .............. BB-6205 .................... Bearing .................................................................... 6205 .............................. 2

17 .............. HBS916W-94-17 ....... C-Ring...................................................................... R52 ............................... 1

18 .............. HBS916W-94-18 ....... Oil Seal .................................................................... 25x52x8 mm ................. 1

19 .............. HBS916W-94-19 ....... Vent Bolt .................................................................. ...................................... 1

20 .............. HBS916W-94-20 ....... Gear Box.................................................................. ...................................... 1

21 .............. HBS916W-94-21 ....... Oil Lens.................................................................... ...................................... 1

22 .............. HBS916W-94-22 ....... Draw Plug ................................................................ ...................................... 1

23 .............. HBS916W-94-23 ....... Key........................................................................... 7x7x45 mm ................... 1

15.0 Electrical Connections

15.1.1 Electrical Connections – 1 Phase

15.1.2 Electrical Panel Layout – 1 Phase

15.2.1 Electrical Connections – 3 Phase

15.2.2 Electrical Panel Layout – 3 Phase

WALTER MEIER (Manufacturing) Inc.

427 New Sanford Road

LaVergne, Tennessee 37086

Phone: 800-274-6848

www.jettools.com

Jet MBS-1014W Operating And Parts Manual

Specifications and Main Features

Frequently Asked Questions

User Manual