Assembly and Parts List
Depth Stop for JWDS-2244/-2550 Drum Sanders
IMPORTANT SAFETY INSTRUCTIONS
• Read and understand entire owner's manual for your Drum Sander before attempting assembly or operation.
• Read and understand the warnings posted on the machi ne and in the manual. Failure to comply with all of
these warnings may cause serious injury.
• Replace warning labels if they become obscured or removed.
• California Proposition 65 Warning: This product contains chem icals known to the State of California to cause
cancer, or birth defects or other reproductive harm.
The depth stop is optional for JWDS-2244,
provided standard with JWDS-2550.
Assembly
1. Thread the rod (#2) into hole of shroud,
and tighten nut (#1) up against shroud.
2. Install plate (#10) using fasteners as
shown.
3. See reverse side for operating
instructions.
Index
No. Part No. Description Size Qty.
723553 Depth Stop Assembly (#1-12)
1 JWDS2244-601 Special Nut 1
2 JWDS2244-602 Threaded Post 1
3 JWDS2244-603 Stop Nut 1
4 JWDS2244-604 Compression Spring 1
5 JWDS2244-605 Half Nut 1
6 TS-1550031 Flat Washer 5.2 x 16 x 1.4T 1
7 TS-1502031 Socket Head Cap Screw M5-0.8P x 12L 1
8 TS-1482051 Hex Cap Screw M6-1.0P x 25L 2
9 TS-1550041 Flat Washer 6.4 x 16 x 1.6T 4
10 JWDS2244-610 Stop Plate 1
11 TS-1541021 Nylon Lock Hex Nut M6-1.0P 2
12 JWDS2244-612 Wave Washer WW-6 1
1
2
3
4
5
8
9
6
10
7
9
11
12
JET
427 New Sanford Road
LaVergne, Tennessee 37086 Part No. M-723553
Ph.: 800-274-6848 Edition 1 06/2018
www.jettools.com Copyright © 2018 JET, a division of JPW Industries, Inc
Depth stop operation
The depth stop nut (A, Figure 1) provides a hard
stop at final sanding depth. It ensures that the
operator will not sand too deeply when he/she
wishes to make multiple pieces the same final
thickness.
1. Rotate handle to position drum at final sanding
depth according to scale. (Figure 1 shows 7/8inch final depth as example).
2. Press button on stop nut to slide nut into general
position, then rotate nut until it firmly contacts
bottom of plate (B). One rotation of nut = 0.10
in. of elevation.
CAUTION: The stop nut is designed to be used
below the plate to allow full support when nut
contacts plate. Using it above the plate may
cause deflection as nut pushes into it.
3. Raise drum and perform sanding operation.
Depending on the workpiece, multiple passes
may be needed until final depth is reached and
stop nut is contacted.
If stop assembly will not be used, loosen left screw
(C) and rotate plate (B) out of the way (see inset).
This allows free drum movement.
Figure 1
Replacement Parts
To order parts or reach our service department, call 1-800-274-6848 Monday th rough Friday, 8:00 a. m. to 5:00
p.m. CST. Having the Model Number and Serial Number of your machine available when you call will allow us to
serve you quickly and accurately.
Non-proprietary parts, such as fasteners, can be found at local hardware stores, or may be ordered from JET.
Some parts are shown for reference only, and may not be available individually
Loading...