JET JLH-75WO-5, JLH-75WO-10, JLH-75WO-15, JLH-75WO-20, JLH-100WO-5 User guide

...
This .pdf document is bookmarked
Operating Instructions and Parts Manual
Lever Operated Chain Hoist

JLH Series

JET
427 New Sanford Road LaVergne, Tennessee 37086 Part No. M-275050
1 Ton model shown

1.0 IMPORTANT SAFETY INSTRUCTIONS

WARNING – To reduce risk of injury:
1. Read and understand the entire owner’s manual before attempting operation. Failure to comply with instructions and warnings may cause serious injury.
2. This lever hoist is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper and safe operation of a lever hoist, do not use until proper training and knowledge have been obtained.
3. Do not use this lever hoist for other than its intended use. If used for other purposes, JET disclaims any real or implied warranty and holds itself harmless from any injury that may result from that use.
4. Do not use lever hoist to lift, support or transport people; or to lift or support loads over people.
5. Do not exceed the rated capacity of the hoist.
6. Do not attempt to extend the lever handle using a “cheater pipe” or any other such device.
7. Do not strike the lever handle with a hammer or any other object.
8. Do not use the chain as a sling. This may cause damage to the chain.
9. Always inspect the lever hoist for damage prior to use. If hoist is damaged, do not use until it has been repaired or replaced.
10. Do not use more than one lever hoist to lift or move a load. If this is unavoidable, each hoist must have the same capacity as the load to be moved.
11. Never allow chain to “set” over sharp edges. All pulls or lifts must be made with straight chain that is free of obstacles.
12. If the lever handle is difficult to operate, then the load exceeds the capacity of the hoist. Reduce load or select a hoist of larger capacity.
13. Do not use hoist if the chain is twisted, kinked or damaged.
14. Do not operate hoist unless load is centered between top and bottom hooks.
15. On hoists with the overload warning lever, do not use this device to measure load weight.
16. Always take time to study the job to be performed and choose the safest method. Do not place yourself or other people in an unsafe position.
17. Always maintain your balance and firm footing when operating the lever hoist.
18. Leave all internal maintenance and inspections to a qualified JET Service Center.
19. Do not attempt to lengthen or repair load chain. Replace chain with factory replacement chain only. Do not use any other type of chain.
20. If welding near the hoist, do not allow the chain or hook to be touched by a live electrode. Prevent weld splatter upon the chain.
21. Never use the hoist if either hook is stretched, deformed, or has a broken or missing safety latch. Always replace the safety latch and/or the hook before placing the hoist back in service.
22. Be sure supporting structures and load­attaching devices used in conjunction with this lever hoist provide an adequate safety factor to handle the rated load plus the weight of the equipment. If in doubt, consult a qualified structural engineer.
23. Keep visitors a safe distance from the work
area. Keep children away.
24. Understand and follow all procedures as set forth in American National Standards titled “Performance Standard for Manually Lever Operated Chain Hoists,” ANSI/ASME HST-3; and “Manually Lever Operated Hoists,” ANSI/ASME B30.21. These standards are available through the American Society of Mechanical Engineers at www.asme.org.
WARNING: This product can expose you
to chemicals including lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to http://www.p65warnings.ca. gov.
2

2.0 Table of Contents

1.0 IMPORTANT SAFETY INSTRUCTIONS ....................................................................................................... 2
2.0 Table of Contents ........................................................................................................................................... 3
3.0 Introduction ..................................................................................................................................................... 3
4.0 Specifications (JLH-75/100/150/250WO) ....................................................................................................... 4
5.0 Specifications (JLH-300/600/900) .................................................................................................................. 5
6.0 Unpacking ...................................................................................................................................................... 6
6.1 Contents of the Carton ............................................................................................................................... 6
7.0 Installation ...................................................................................................................................................... 6
8.0 Pre-Operation Inspection ............................................................................................................................... 6
8.1 Inspecting the Load Chain .......................................................................................................................... 6
8.2 Inspecting Hooks ........................................................................................................................................ 6
8.3 Other Inspections ....................................................................................................................................... 7
9.0 Operation ....................................................................................................................................................... 7
9.1 Precautions ................................................................................................................................................ 8
10.0 Point Hooks .................................................................................................................................................. 9
11.0 Overload Protection ..................................................................................................................................... 9
12.0 Inspection and Maintenance ........................................................................................................................ 9
13.0 Allowable Limits for Load Chain and Hooks ............................................................................................... 10
13.1 Load Chain ............................................................................................................................................. 10
13.2 Hooks (Top and Bottom) ........................................................................................................................ 10
14.0 Timing Marks for Gear Replacement ......................................................................................................... 11
15.0 Troubleshooting ......................................................................................................................................... 11
16.0 Replacement Parts ..................................................................................................................................... 12
16.1 JLH Series Lever Hoists (JLH-75/100/150/250/300/600/900WO) .......................................................... 12
16.2 Parts List: JLH-75WO (0.75 Ton) ........................................................................................................... 13
16.3 Parts List: JLH-100WO (1 Ton) .............................................................................................................. 15
16.4 Parts List: JLH-150WO (1.5 Ton) ........................................................................................................... 17
16.5 Parts List: JLH-250WO (2.5 Ton) ........................................................................................................... 19
16.6 Parts List: JLH-300WO (3 Ton) .............................................................................................................. 21
16.7 Parts List: JLH-600WO (6 Ton) .............................................................................................................. 23
16.8 Parts List: JLH-900 (9 Ton) .................................................................................................................... 25
17.0 Warranty and Service ................................................................................................................................. 27

3.0 Introduction

This manual is provided by JET covering the safe operation and maintenance procedures for the JET JLH­Series Lever Hoists. This manual contains instructions on installation, safety precautions, general operating procedures, maintenance instructions and parts breakdown. This tool has been designed and constructed to provide consistent, long-term operation if used in accordance with instructions set forth in this manual. If there are any questions or comments, please contact either your local supplier or JET. JET can also be reached at our web site: www.jettools.com.
The JET JLH-Series Lever Hoists comply with ANSI/ASME B30.21 and HST-3 standards.
The specifications in this manual were current at time of publication, but because of our policy of continuous improvement, JET, reserves the right to change specifications at any time and without prior notice, without incurring obligations.
Register your product using the mail-in card provided, or register online: http://www.jettools.com/us/en/service-and-support/warranty/registration/
3

4.0 Specifications (JLH-75/100/150/250WO)

Min.
Stock
Number Description
376100 JLH-75WO-5 0.75 5 11.02 1 5.6 1.14 63.88 10.24 4.69 5.67 0.93 13.07 376101 JLH-75WO-10 376102 JLH-75WO-15 376103 JLH-75WO-20
376200 JLH-100WO-5 1 5 11.81 1 5.6 1.14 79.30 10.24 4.69 5.67 1.14 13.6 376201 JLH-100WO-10 1 10 11.81 1 5.6 1.14 79.30 10.24 4.69 5.67 1.14 15.91 376202 JLH-100WO-15 1 15 11.81 1 5.6 1.14 79.30 10.24 4.69 5.67 1.14 18.22 376203 JLH-100WO-20 1 20 11.81 1 5.6 1.14 79.30 10.24 4.69 5.67 1.14 20.53
376300 JLH-150WO-5 1.5 5 13.19 1 7.1 0.86 74.89 10.24 4.96 6.38 1.26 17.94 376301 JLH-150WO-10 1.5 10 13.19 1 7.1 0.86 74.89 10.24 4.96 6.38 1.26 21.75 376302 JLH-150WO-15 1.5 15 13.19 1 7.1 0.86 74.89 10.24 4.96 6.38 1.26 25.56 376303 JLH-150WO-20 1.5 20 13.19 1 7.1 0.86 74.89 10.24 4.96 6.38 1.26 29.37
376400 JLH-250WO-5 2.5 5 14.76 1 8.8 0.60 81.50 10.24 5.90 6.97 1.44 25 376401 JLH-250WO-10 2.5 10 14.76 1 8.8 0.60 81.50 10.24 5.90 6.97 1.44 30.55 376402 JLH-250WO-15 2.5 15 14.76 1 8.8 0.60 81.50 10.24 5.90 6.97 1.44 36.1 376403 JLH-250WO-20 2.5 20 14.76 1 8.8 0.60 81.50 10.24 5.90 6.97 1.44 41.65
Rated
Capcty.
(ton)
0.75
0.75
0.75
Standard
Lift (ft.)
Distance between
hooks (in.)
“A”
10 11.02 1 5.6 1.14 63.88 10.24 4.69 5.67 0.93 15.38 15 11.02 1 5.6 1.14 63.88 10.24 4.69 5.67 0.93 17.69 20 11.02 1 5.6 1.14 63.88 10.24 4.69 5.67 0.93 20
No.
of
falls
Load
Chain
Diameter
(mm)
Lift per
full turn
(in.)
Lbs.
Pull
to Lift
capacity
Lever
Length
(in.)
“B”
(in.) “C”
Overall
width
(in.)
“D”
Hook
Throat
Opening
(in.)
“E”
Net
Weight
(lbs)
NOTE: The above stock numbers are representative; chain is available in other lengths. Specify length when ordering. Some models are available with point (“shipyard”) hooks; specify when ordering.
4

5.0 Specifications (JLH-300/600/900)

Min.
Stock
Number Description
376500 JLH-300WO-5 3 5 15.55 1 10 0.762 81.50 16.34 6.26 7.52 1.54 33.07 376501 JLH-300WO-10 3 10 15.55 1 10 0.762 81.50 16.34 6.26 7.52 1.54 40.57 376502 JLH-300WO-15 3 15 15.55 1 10 0.762 81.50 16.34 6.26 7.52 1.54 48.07 376503 JLH-300WO-20 3 20 15.55 1 10 0.762 81.50 16.34 6.26 7.52 1.54 55.57
376600 JLH-600WO-5 6 5 21.26 2 10 0.381 83.70 16.34 8.54 7.52 1.97 57.32 376601 JLH-600WO-10 6 10 21.26 2 10 0.381 83.70 16.34 8.54 7.52 1.97 72.32 376602 JLH-600WO-15 6 15 21.26 2 10 0.381 83.70 16.34 8.54 7.52 1.97 87.32 376603 JLH-600WO-20 6 20 21.26 2 10 0.381 83.70 16.34 8.54 7.52 1.97 102.32
376700 JLH-900WO-5 9 5 26.79 3 10 0.254 88.16 16.34 16.3 7.52 2.13 95 376701 JLH-900WO-10 9 10 26.79 3 10 0.254 88.16 16.34 16.3 7.52 2.13 117.5 376702 JLH-900WO-15 9 15 26.79 3 10 0.254 88.16 16.34 16.3 7.52 2.13 140 376703 JLH-900WO-20 9 20 26.79 3 10 0.254 88.16 16.34 16.3 7.52 2.13 162.5
Rated
Capcty.
(ton)
Standard
Lift (ft.)
Distance between
hooks (in.)
“A”
No.
of
falls
Load
Chain
Diameter
(mm)
Lift per
full turn
(in.)
Lbs.
Pull
to Lift
capacity
Lever
Length
(in.)
“B”
(in.) “C”
Overall
width
(in.)
“D”
Hook
Throat
Opening
(in.)
“E”
Net
Weight
(lbs)
NOTE: The above stock numbers are representative; chain is available in other lengths. Specify length when ordering. Some models are available with point (“shipyard”) hooks; specify when ordering.
5

6.0 Unpacking

Open carton and check for shipping damage. Report any damage immediately to your distributor and shipping agent. Do not discard any shipping material until the Lever Hoist is assembled and running properly. Read this entire instruction manual thoroughly for set-up, maintenance and safety instructions.

6.1 Contents of the Carton

1 Lever Hoist 1 Operating Instructions and Parts Manual 1 Product Registration Card

7.0 Installation

Support for the hoist may be hook, clevis pin, trolley, or beam clamp. Whatever method of suspension is chosen, the support components
must be rated equal to, or greater than the
capacity of the lever hoist. Supporting structures, such as I-Beams, should be installed by properly licensed professional installers.
8.0 Pre-Operation
Inspection

8.1 Inspecting the Load Chain

1. A chain stop must be attached to the second­to-last link on the slack end of the chain. See Figure 2.
Do not opera te the hoist with a
twisted, kinked or damaged chain. Do not splice the chain.
2. Check that the chain does not twist along its length from hoist to hook. If twist is present on units with multiple falls, the hook must be passed back through the chain loop to remove all twist in the chain.
3. Replace the chain if links are stretched too long or seriously worn on the surface, especially at the points where links contact each other. See “Allowable Limits” on page 12 for measuring chain elongation.
4. Do not use a chain that is seriously rusted or cracked.
5. Periodically apply a light coat of 30-weight oil to the chain. This will create easier operation and prolong the chain’s life. For optimum results, clean the chain with an acid-free solution before oiling.
your JET lever hoist is designed, manufactured, and tested for proper fit and durability. If chain should ever need replacin g, for your own safety use factory replacement chain only. Use of other than factory replacement chain may cause serious injury and/or damage to the lever hoist.
Never extend load chain by welding a second piece to the original.

8.2 Inspecting Hooks

It is important to check top and bottom hooks for proper opening and other signs of deformation or damage. Replace a hook immediately if any of the following problems are identified:
The safety latch no longer contacts the hook opening.
Features and terminology
Figure 1
Figure 2
The load chain supplied with
6
The vertical angle at the neck of the hook reaches 10° (see Figure 3).
Chemical corrosion or cracks on the hook.
Excessive wear on the inside surface.
The throat opening has enlarged. (See sect.
13.2 for the maximum allowable limits for the throat opening.)
Do not attempt repair of a hook
by heat treating, bending or attaching anything by welding. Such procedures will weaken and may cause failure of the hook.
Figure 3

8.3 Other Inspections

1. Check for appropriate clicking sounds: With
the selector lever in UP position, there will be a clicking sound when the lever handle is rotated
in either direction. When the selector lever is in
DOWN position, there will be a clicking sound only when the lever handle is ratcheted back into position but not as the load is lowered. If
these sounds are not present, or if irregular
clicking noises develop, do not use the hoist – have it inspected and repaired by an authorized service center.
2. If the lever hoist has not been used for an
extended period of time, check for proper operation before putting into service.
3. The brake mechanism must be kept clean and
free from dirt, water, and oil. Never allow oil to penetrate the braking mechanism. The brake should not slip while using the hoist.

9.0 Operation

The JLH Lever Hoist may be used either in vertical position as a hoist; or in angled or horizontal position as a puller. Below is the general procedure for operating the hoist:
1. Set the top hook securely.
2. Place the selector switch on the handle in the
center neutral position, and pull out on the handwheel (A, Figure 4). This will allow “free-
wheel” mode. Pull the load chain by hand to position the bottom hook.
Figure 4
3. Correctly center the load on the bottom hook (Figure 5). Incorrect loading is dangerous to the operator, the lever hoist, and the load.
Never load the hook in front of the safety
latch (A, Figure 6).
Never load the hook tip (B, Figure 6).
Never load the hook off the centerline (C,
Figure 6).
Never load the hook sideways (D, Figure
6).
Figure 5
Figure 6
7
4. Rotate the handwheel clockwise while simultaneously pulling down on the load chain, (B, Figure 4). The handwheel will snap back into place, re-engaging the gear.
5. Move selector switch to the UP position. Ratchet the lever to raise or pull the load. Do not overload the lever hoist.
Do not touch the handwheel
while lifting or lowering. Do not operate freewheel mode while there is a load on the hoist.
6. To release or lower the load, turn selector switch on the handle to the DOWN position and ratchet the handle.
NOTE: If the chain is pulled too suddenly in free­wheel mode, the brake may set preventing further pulling. Re-set the hoist by repeating step number 4 above, and then set the hoist back into freewheel mode to continue the operation.
Avoid lifting one load with two hoists. If this is unavoidable, apply equal weight to both hoists and
use hoists with the proper lift capacity. Capacity of
each hoist must be equal to the to tal load to be lifted.

9.1 Precautions

During lifting operations, do not stand under the load.
Do not use any extension on the lever handle (Figure 7). Do not use your foot to apply pressure to the lever handle (Figure 8).
Figure 7
Figure 8
Prevent the chain from dragging over sharp edges or corners. This will cause links to weaken, bend, or break.
When connecting to a wire rope sling, the lever hoist must be applied along a straight line parallel to the surface on which it is resting. See Figure 9.
Figure 9
When lifting loads, hook the load with slings.
Do not use the lever hoist chain as a sling
(Figure 10).
Figure 10
Both ends of a sling or rope must be completely on the inside of the safety latch before pulling or lifting the load. Do not put one end on the inside of the latch and leave the other end on the hook end outside the latch.
8

10.0 Point Hooks

12.0 Inspection and
Point or “shipyard” hooks are available for your JET lever hoist, in 1.6 ton and 3.2 ton load sizes. They are available in both upper and lower hook styles.
Point hooks are used in the metal and ship building industries, and are designed for positioning steel plate and fixtures before welding.

11.0 Overload Protection

All models of the JLH Lever Hoist have overload protection in the form of a slip clutch, which will allow the handle to rotate without lifting an excessive load. The slip clutch is effective at 160% +/-20% of rated hoist capacity.
If an overload occurs (handle rotation fails to raise
load), immediately move selector lever to DOWN
position, lower and remove the load. Select a load within the hoist’s capacity to continue operation.
Make sure loads are within
rated capacity of hoist. Excessive acti vation of overload limiter will result in undue wear to the unit, and may cause erratic performance such as lifting capacities falling outside normal ratings.
The overload slip clutch has been pre-adjusted at the factory and should not require any adjustment by the user. It should not be lubricated. If future adjustment or repair to the slip clutch should ever be needed, this must be done by qualified service personnel.
Maintenance
Read and follow ANSI Inspection and Maintenance Instructions. Know the meaning of Frequent Inspection, Periodic Inspection, Normal Service, Heavy Service, and Severe Service. It is the customer’s responsibility to understand and follow all ANSI and JET inspection and maintenance instructions.
The lever hoist should be stored in a clean, dry environment. Clean and oil the hoist before storage.
Hoists that are installed out-of-doors should be covered or brought inside when not in use.
Periodically apply a light coat of 30 weight oil to the load chain.
Annually, the hoist should be disassembled, inspected, and cleaned by trained and experienced personnel only. Contact a JET authorized service center by calling your dealer or visiting our web site at jettools.com.
9
13.0 Allowable Limits for
Load Chain and Hooks

13.1 Load Chain

Carefully inspect the entire load chain. As illustrated in Figure 11, measure five consecutive links with calipers to find the length, Compare the results with the table in Figure 11. Check every three feet and especially where excessive wear is indicated. Any load chain that shows noticeable deformation or heat influence must be replaced with a new one.
Never extend load chain by
welding a second piece to the original.
Hoist
Capacity
0.8 ton 79 81.3
1 ton 79 81.3
1.6 ton 100 102.9
2.5 ton 124 127.
3.2 ton 141 145.1
6.3 ton 141 145.1
9 ton 141 145.1
5 Links Normal
(mm)
5 Links Limit
Replace if

13.2 Hooks (Top and Bottom)

Replace the hook when the distance between indicator points – “A” in Figures 12 and 13 – is wider than the limits given in the table.
Never heat treat the hook or attach anything to the hook by welding.
Hoist
Capacity
0.8 ton 41.8 44
1 ton 49.9 52.5
1.6 ton 52.3 55
2.5 ton 59.9 63
3.2 ton 62.7 66
6.3 ton 84.6 89
“A” Dimension
Normal
(mm)
Figure 12
“A” Dimension
Replace if
Figure 11
Hoist
Capacity
9 ton 54.1 57
“A” Dimension
Normal
(mm)
Figure 13
“A” Dimension
Replace if
10

14.0 Timing Marks for Gear Replacement

If the gears on the JLH hoist need replacement or removal for any reason, make sure they are re-installed correctly. Figure 14 shows the proper orientation of the timing marks when meshing the gears.
Figure 14

15.0 Troubleshooting

The numbers in parentheses refer to the parts breakdown on the following page.
Trouble Probable Cause Remedy*
Hoist will not lift (no clicking sound).
Load slips or drifts while being lowered.
Hoist will not lower load.
Handwheel will not move in and out.
Hoist will not freewheel.
Pawl (#12) not engaging ratchet disc (#15); possible dirt or foreign material.
Pawl spring (#11) is damaged. Replace pawl spring.
Selector switch spring (#23) is loose or damaged.
Dirt/corrosion/foreign material in hoist components.
Brake is slipping. Disc hub (#14) is worn from long-term use, or is damaged from overloading or misuse.
The brake has caught. (Hoist was left under load condition for extended period, or was shock-loaded while operating.)
Brake components are corroded or damaged.
Disc hub (#14) is damaged. Replace disc hub.
Brake has caught because load chain was pulled too hard.
Clean and lubricate pawl/ratchet disc assemblies.
Tighten or replace selector switch spring.
Inspect and correct problem. Keep hoist clean and lubricated.
Replace disc hub. Do not overload hoist.
Place selector lever in DOWN position and pull hard on the lever handle to re­set the brake. Resume operation.
Replace components as needed; keep hoist clean and lubricated.
Re-set by rotating handwheel clockwise while pulling down on load chain. Return hoist to freewheel mode and continue. Pull load chain less forcibly.
* Any disassembly or repair of the lever hoist should be performed by properly trained personnel. Call JET, or go to jettools.com to find an authorized Service Center nearest you.
11

16.0 Replacement Parts

Replacement parts are listed on the following pages. To order parts or reach our service department, call 1­800-274-6848 Monday through Friday, 8:00 a.m. to 5:00 p.m. CST. Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately.

16.1 JLH Series Lever Hoists (JLH-75/100/150/250/300/600/900WO)

12

16.2 Parts List: JLH-75WO (0.75 Ton)

Non-numbered parts listed under each assembly are parts that make up that assembly.
Index No. Part No. Description Size Qty
1 ................ JLH80-1G .................. Gear Case Assembly (0.75, 1 Ton) ......................... ...................................... 1
.................. .................................. Gear Case ............................................................... ...................................... 1
.................. .................................. Bushing .................................................................... ...................................... 3
.................. .................................. Cover Pl ate .............................................................. ...................................... 1
2 ............... JLH80-2 ..................... Spur Gear Assembly (0.75, 1 Ton) .......................... ...................................... 2
.................. .................................. Spur Gear ................................................................ ...................................... 2
.................. .................................. Pinion Gear .............................................................. ...................................... 2
3-2 ............. JLH80-3-2 ................. Driving Shaft (0.75, 1 Ton) ...................................... ...................................... 1
4 ................ JLH80-4 ..................... Load Gear (0.75, 1 Ton) .......................................... ...................................... 1
5 ................ JLH80-5 ..................... Gear Side Plate Assembly (0.75, 1 Ton) ................. ...................................... 1
.................. .................................. Gear Side Plate ....................................................... ...................................... 1
.................. .................................. Bushing .................................................................... ...................................... 2
6 ................ JLH80-6 ..................... Caged Roller Bearings (0.75, 1 Ton) ....................... Ø35xØ25x10mm ........... 2
7 ................ JLH80-7 ..................... Load Sheave (0.75, 1 Ton)) ..................................... ...................................... 1
8 ................ JLH80-8 ..................... Guide Roller (0.75, 1 Ton) ....................................... ...................................... 2
9 ................ JLH80-9 ..................... Stripper (0.75, 1 Ton)............................................... ...................................... 1
10 .............. JLH80-10 ................... Lever Side Plate Assembly (0.75, 1 Ton) ................ ...................................... 1
.................. .................................. Lever Side Plate ...................................................... ...................................... 1
.................. .................................. Stay Bolt .................................................................. ...................................... 4
.................. .................................. Pawl Pin ................................................................... ...................................... 2
11 .............. JLH80-11 ................... Pawl Spring (0.75, 1 Ton) ........................................ ...................................... 2
12 .............. JLH160-12 ................. Pawl (0.75, 1, 1.5 Ton) ............................................ ...................................... 2
13 .............. JLH160-13 ................. Snap Ring (0.75, 1, 1.5 Ton) ................................... Ø 9mm .......................... 2
14 .............. JLH160-14 ................. Disc Hub (0.75, 1, 1.5, 2.5 Ton)............................... ...................................... 1
15 .............. JLH160-15 ................. Ratchet Disc (0.75, 1, 1.5, 2.5 Ton) ......................... ...................................... 1
16-1 ........... JLH80-16-1 ............... Brake Cover Assembly (0.75, 1 Ton) ...................... ...................................... 1
................. .................................. Brake Cover ............................................................. ...................................... 1
.................. .................................. Handle Case ............................................................ ...................................... 1
................. .................................. Bushing .................................................................... ...................................... 1
.................. .................................. Thread Housing ....................................................... ...................................... 1
17-1 ........... JLH160-17G .............. Acorn Nut (0.75, 1, 1.5, 2.5 Ton) ............................. M6 ................................. 2
17A ............ JLH160-17AG ........... Lock Washer (0.75, 1, 1.5, 2.5 Ton) ........................ 6mm .............................. 2
18 ............. JLH80-18G ................ Lock Washer (0.75 to 9 Ton) ................................... 8mm .............................. 8
19 .............. JLH80-19G ................ Acorn Nut (0.75 to 9 Ton) ........................................ M8 ................................. 8
20-2 ........... JLH160-20-2 ............. Change Over Gear (0.75, 1, 1.5, 2.5 Ton) ............... ...................................... 1
20-2L ......... JLH80-20L-2 ............. Overload Limiter Assembly ...................................... ...................................... 1
.................. .................................. Overload Limiting Plate ........................................... ...................................... 1
.................. .................................. Change Over Gear .................................................. ...................................... 1
.................. .................................. Pressure Plate ......................................................... ...................................... 1
.................. .................................. Dish Spring .............................................................. ...................................... 1
.................. .................................. Washer .................................................................... ...................................... 1
.................. .................................. Lock Washer ............................................................ ...................................... 1
.................. .................................. Round Nut ............................................................... M30x1 ........................... 1
21 .............. JLH160-21 ................. Change Over Pawl (0.75, 1, 1.5, 2.5 Ton) ............... ...................................... 1
22 .............. JLH160-22 ................. Spring Shaft (0.75, 1, 1.5, 2.5 Ton) ......................... ...................................... 1
23 .............. JLH160-23 ................. Spring (0.75, 1, 1.5, 2.5 Ton) ................................... ...................................... 1
24-1 ........... JLH80-24-1 ............... Lever Handle Assembly (0.75, 1, 1.5, 2.5 Ton) ....... ...................................... 1
.................. .................................. Lever Handle ........................................................... ...................................... 1
.................. .................................. Selector Lever.......................................................... ...................................... 1
.................. .................................. Change Over Shaft .................................................. ...................................... 1
.................. .................................. Bolt........................................................................... ...................................... 2
.................. .................................. Spring Seat .............................................................. ...................................... 1
.................. .................................. Bushing .................................................................... ...................................... 1
24A-1 ......... JLH80-24A-1 ............. Rubber Grip (0.75, 1, 1.5, 2.5 Ton) ........................ ...................................... 1
25 .............. JLH160-25G .............. Socket Head Cap Screw (0.75, 1, 1.5, 2.5 Ton) ...... M6 x 12 ......................... 1
25A ............ JLH160-25AG ........... Lock Washer (0.75, 1, 1.5 Ton) ............................... 6mm .............................. 1
26-2 ........... JLH160-26-2A ........... Stop Knob (0.75, 1, 1.5, 2.5 Ton)
27-1 ........... JLH160-27-1 ............. Twisting Spring (0.75, 1, 1.5, 2.5 Ton) ................... ...................................... 1
13
.............................. ...................................... 1
Index No. Part No. Description Size Qty
28-2 ........... JLH160-28-2 ............. Hand Wheel Assembly (0.75, 1, 1.5, 2.5 Ton) ......... ...................................... 1
.................. .................................. Hand W heel ............................................................. ...................................... 1
.................. .................................. Steel Ball Spring ...................................................... ...................................... 2
.................. .................................. Steel Ball.................................................................. ...................................... 2
29-1 ........... JLH160-29-1 ............. Hand Wheel Cap (0.75, 1, 1.5, 2.5 Ton) .................. ...................................... 1
30-1 ........... JLH160-30-1 ............. Hand Wheel Base Assembly (0.75, 1, 1.5, 2.5 Ton) ........................................
.................. .................................. Hand Wheel Base .................................................... ...................................... 1
.................. .................................. Bushing .................................................................... ...................................... 2
31-1 ........... F001754 .................... Lock Nut................................................................... M8 ................................. 1
32-1 ........... JLH80-32-1 ............... Steel Cable Ring (0.75 to 2.5 Ton) .......................... ...................................... 1
33 .............. JLH80-33 ................... Rivet (0.75 to 9 Ton) ................................................ 3 x 6mm ........................ 6
34-1 ........... LM000191 ................. Name Plate JLH-75 ................................................. ...................................... 1
35 .............. F001753 .................... Lock Nut................................................................... M6 ................................. 1
36 .............. JLH80-36 ................... Bottom Hook Shaft (0.75, 1 Ton) ............................. ...................................... 1
37 .............. JLH80-37-1 ............... Safety Latch Kit (0.75 Ton) ...................................... ...................................... 2
.................. .................................. Safety Latch ............................................................. ...................................... 2
.................. .................................. Double Spring .......................................................... ...................................... 2
.................. .................................. Socket Cap Screw ................................................... M4 x 23 ......................... 2
.................. .................................. Lock Nut................................................................... M4 ................................. 2
38. ............. JLH80-38-1 ............... Bottom Hook Assembly (incls. 35 & 36) .................. ...................................... 1
.................. .................................. Bottom Hook ............................................................ ...................................... 1
.................. .................................. Safety Latch ............................................................. ...................................... 1
.................. .................................. Double Spring .......................................................... ...................................... 1
.................. .................................. Socket Cap Screw ................................................... M4 x 23 ......................... 1
.................. .................................. Lock Nut................................................................... M4 ................................. 1
.................. .................................. Bottom Hook Holder ................................................ ...................................... 2
.................. .................................. Rivet......................................................................... 6 x 24mm ...................... 4
39 .............. JLH80-39 ................... Top Hook Shaft (0.75, 1 Ton) .................................. ...................................... 1
40 .............. JLH80-40-1 ............... Top Hook Assembly................................................. ...................................... 1
.................. .................................. Top Hook ................................................................. ...................................... 1
.................. .................................. Safety Latch ............................................................. ...................................... 1
.................. .................................. Double Spring .......................................................... ...................................... 1
.................. .................................. Socket Cap Screw ................................................... M4 x 23 ......................... 1
.................. .................................. Lock Nut................................................................... M4 ................................. 1
.................. .................................. Top Hook Holder...................................................... ...................................... 2
.................. .................................. Rivet......................................................................... 6 x 24mm ...................... 2
41 .............. JLH80-41 ................... Chain Stop (0.75, 1 Ton) ......................................... ...................................... 1
42 .............. JLH80-42 ................... Drive Shaft Washer (0.75, 1 Ton) ............................ ...................................... 1
49 .............. JLH80-49 ................... Load Chain (0.75, 1 Ton) – specify length ............... #100,Ø5.6 x 15.7mm .... 1
50 .............. JLH160-50 ................. Rubber Grip Fastening (0.75, 1, 1.5, 2.5 Ton) ......... ...................................... 1
50A ............ JLH160-50A .............. Fastening Screw (0.75, 1, 1.5, 2.5 Ton) .................. ...................................... 1
.................. JLH-5027WL ............. Warning Label (not shown) ...................................... 50x27mm ...................... 1
52 .............. L100-WT ................... Pendant Warning Tag .............................................. ...................................... 1
Note: Top and bottom hooks are sold as an assembly only.
When ordering replacement chain (#49), specify length.
14

16.3 Parts List: JLH-100WO (1 Ton)

Non-numbered parts listed under each assembly are parts that make up that assembly.
Index No. Part No. Description Size Qty
1 ................ JLH80-1G .................. Gear Case Assembly (0.75, 1 Ton) ......................... ...................................... 1
.................. .................................. Gear Case ............................................................... ...................................... 1
.................. .................................. Bushing .................................................................... ...................................... 3
.................. .................................. Cover Pl ate .............................................................. ...................................... 1
2 ............... JLH80-2 ..................... Spur Gear Assembly (0.75, 1 Ton) .......................... ...................................... 2
.................. .................................. Spur Gear ................................................................ ...................................... 2
.................. .................................. Pinion Gear .............................................................. ...................................... 2
3-2 ............. JLH80-3-2 ................. Driving Shaft (0.75, 1 Ton) ...................................... ...................................... 1
4 ................ JLH80-4 ..................... Load Gear (0.75, 1 Ton) .......................................... ...................................... 1
5 ................ JLH80-5 ..................... Gear Side Plate Assembly (0.75, 1 Ton) ................. ...................................... 1
.................. .................................. Gear Side Plate ....................................................... ...................................... 1
.................. .................................. Bushing .................................................................... ...................................... 2
6 ................ JLH80-6 ..................... Caged Roller Bearings (0.75, 1 Ton) ....................... Ø35xØ25x10mm ........... 2
7 ................ JLH80-7 ..................... Load Sheave (0.75, 1 Ton) ...................................... ...................................... 1
8 ................ JLH80-8 ..................... Guide Roller (0.75, 1 Ton) ....................................... ...................................... 2
9 ................ JLH80-9 ..................... Stripper (0.75, 1 Ton)............................................... ...................................... 1
10 .............. JLH80-10 ................... Lever Side Plate Assembly (0.75, 1 Ton) ................ ...................................... 1
.................. .................................. Lever Side Plate ...................................................... ...................................... 1
.................. .................................. Stay Bolt .................................................................. ...................................... 4
.................. .................................. Pawl Pin ................................................................... ...................................... 2
11 .............. JLH80-11 ................... Pawl Spring (0.75, 1 Ton) ........................................ ...................................... 2
12 .............. JLH160-12 ................. Pawl (0.75, 1, 1.5 Ton) ............................................ ...................................... 2
13 .............. JLH160-13 ................. Snap Ring (0.75, 1, 1.5, 2.5 Ton) ............................ Ø 9mm .......................... 2
14 .............. JLH160-14 ................. Disc Hub (0.75, 1, 1.5, 2.5 Ton)............................... ...................................... 1
15 .............. JLH160-15 ................. Ratchet Disc (0.75, 1, 1.5, 2.5 Ton) ......................... ...................................... 1
16-1 ........... JLH80-16-1 ............... Brake Cover Assembly (0.75, 1 Ton) ...................... ...................................... 1
................. .................................. Brake Cover ............................................................. ...................................... 1
.................. .................................. Handle Case ............................................................ ...................................... 1
................. .................................. Bushing .................................................................... ...................................... 1
.................. .................................. Thread Housing ....................................................... ...................................... 1
17-1 ........... JLH160-17G .............. Acorn Nut (0.75, 1, 1.5, 2.5 Ton) ............................. M6 ................................. 2
17A ............ JLH160-17AG ........... Lock Washer (0.75, 1, 1.5, 2.5 Ton) ........................ 6mm .............................. 2
18 ............. JLH80-18G ................ Lock Washer (0.75 to 9 Ton) ................................... 8mm .............................. 8
19 .............. JLH80-19G ................ Acorn Nut (0.75 to 9 Ton) ........................................ M8 ................................. 8
20-2 ........... JLH160-20-2 ............. Change Over Gear (0.75, 1, 1.5, 2.5 Ton) ............... ...................................... 1
20-2L ......... JLH100-20L-2 ........... Overload Limiter Assembly ...................................... ...................................... 1
.................. .................................. Overload Limiting Plate ........................................... ...................................... 1
.................. .................................. Change Over Gear .................................................. ...................................... 1
.................. .................................. Pressure Plate ......................................................... ...................................... 1
.................. .................................. Dish Spring .............................................................. ...................................... 1
.................. .................................. Washer .................................................................... ...................................... 1
.................. .................................. Lock Washer ............................................................ ...................................... 1
.................. .................................. Round Nut ............................................................... M30x1 ........................... 1
21 .............. JLH160-21 ................. Change Over Pawl (0.75, 1, 1.5, 2.5 Ton) ............... ...................................... 1
22 .............. JLH160-22 ................. Spring Shaft (0.75, 1, 1.5, 2.5 Ton) ......................... ...................................... 1
23 .............. JLH160-23 ................. Spring (0.75, 1, 1.5, 2.5 Ton) ................................... ...................................... 1
24-1 ........... JLH80-24-1 ............... Lever Handle Assembly (0.75, 1, 1.5, 2.5 Ton) ....... ...................................... 1
.................. .................................. Lever Handle ........................................................... ...................................... 1
.................. .................................. Selector Lever.......................................................... ...................................... 1
.................. .................................. Change Over Shaft .................................................. ...................................... 1
.................. .................................. Bolt........................................................................... ...................................... 2
.................. .................................. Spring Seat .............................................................. ...................................... 1
.................. .................................. Bushing .................................................................... ...................................... 1
24A-1 ......... JLH80-24A-1 ............. Rubber Grip (0.75, 1 , 1.5, 2.5 Ton) ........................ ...................................... 1
25 .............. JLH160-25G .............. Socket Head Cap Screw (0.75, 1, 1.5, 2.5 Ton) ...... M6 x 12 ......................... 1
25A ............ JLH160-25AG ........... Lock Washer (0.75, 1, 1.5 Ton) ............................... 6mm .............................. 1
26-2 ........... JLH160-26-2A ........... Stop Knob (0.75, 1, 1.5, 2.5 Ton) ............................ ...................................... 1
27-1 ........... JLH160-27-1 ............. Twisting Spring (0.75, 1, 1.5, 2.5 Ton) .................... ...................................... 1
15
Index No. Part No. Description Size Qty
28-2 ........... JLH160-28-2 ............. Hand Wheel Assembly (0.75, 1, 1.5, 2.5 Ton) ......... ...................................... 1
.................. .................................. Hand W heel ............................................................. ...................................... 1
.................. .................................. Steel Ball Spring ...................................................... ...................................... 2
.................. .................................. Steel Ball.................................................................. ...................................... 2
29-1 ........... JLH160-29-1 ............. Hand Wheel Cap (0.75, 1, 1.5, 2.5 Ton) .................. ...................................... 1
30-1 ........... JLH160-30-1 ............. Hand Wheel Base Assembly (0.75, 1, 1.5, 2.5 Ton) ...................................... 1
.................. .................................. Hand Wheel Base .................................................... ...................................... 1
.................. .................................. Bushing .................................................................... ...................................... 2
31-1 ........... F001754 .................... Lock Nut................................................................... M8 ................................. 1
32-1 ........... JLH80-32-1 ............... Steel Cable Ring (0.75 to 2.5 Ton) .......................... ...................................... 1
33 .............. JLH80-33 ................... Rivet (0.75 to 9 Ton) ................................................ 3 x 6mm ........................ 6
34-1 ........... LM000192 ................. Name Plate JLH-100 ............................................... ...................................... 1
35 .............. F001753 .................... Lock Nut................................................................... M6 ................................. 1
36 .............. JLH80-36 ................... Bottom Hook Shaft (0.75, 1 Ton) ............................. ...................................... 1
37 .............. JLH100-37-1 ............. Safety Latch Kit (1 Ton)
.................. .................................. Safety Latch ............................................................. ...................................... 2
.................. .................................. Double Spring .......................................................... ...................................... 2
.................. .................................. Socket Cap Screw ................................................... M4 x 23 ......................... 2
.................. .................................. Lock Nut................................................................... M4 ................................. 2
38 ............. JLH100-38-1 ............. Bottom Hook Assembly (incls. 35 & 36)
.................. .................................. Bottom Hook ............................................................ ...................................... 1
.................. .................................. Safety Latch ............................................................. ...................................... 1
.................. .................................. Double Spring .......................................................... ...................................... 1
.................. .................................. Socket Cap Screw ................................................... M4 x 23 ......................... 1
.................. .................................. Lock Nut................................................................... M4 ................................. 1
.................. .................................. Bottom Hook Holder ................................................ ...................................... 2
.................. .................................. Rivet......................................................................... 6 x 24mm ...................... 4
39 .............. JLH80-39 ................... Top Hook Shaft (0.75, 1 Ton) .................................. ...................................... 1
40 .............. JLH100-40-1 ............. Top Hook Assembly (1 Ton) .................................... ...................................... 1
.................. .................................. Top Hook ................................................................. ...................................... 1
.................. .................................. Safety Latch ............................................................. ...................................... 1
.................. .................................. Double Spring .......................................................... ...................................... 1
.................. .................................. Socket Cap Screw ................................................... M4 x 23 ......................... 1
.................. .................................. Lock Nut................................................................... M4 ................................. 1
.................. .................................. Top Hook Holder...................................................... ...................................... 2
.................. .................................. Rivet......................................................................... 6 x 24mm ...................... 2
41 .............. JLH80-41 ................... Chain Stop (0.75, 1 Ton) ......................................... ...................................... 1
42 .............. JLH80-42 ................... Drive Shaft Washer (0.75, 1 Ton) ............................ ...................................... 1
49 .............. JLH80-49 ................... Load Chain (0.75, 1 Ton) – specify length ............... #100,Ø5.6 x 15.7mm .... 1
50 .............. JLH160-50 ................. Rubber Grip Fastening (0.75, 1, 1.5, 2.5 Ton) ......... ...................................... 1
50A ............ JLH160-50A .............. Fastening Screw (0.75, 1, 1.5, 2.5 Ton) .................. ...................................... 1
.................. JLH-5027WL ............. Warning Label (not shown) ...................................... 50x27mm ...................... 1
52 .............. L100-WT ................... Warning Tag ............................................................ ...................................... 1
Note: Top and bottom hooks are sold as an assembly only.
When ordering replacement chain (#49), specify length.
............................................. ........................................ 2
................... ...................................... 1
16

16.4 Parts List: JLH-150WO (1.5 Ton)

Non-numbered parts listed under each assembly are parts that make up that assembly.
Index No. Part No. Description Size Qty
1 ................ JLH160-1G ................ Gear Case Assembly ............................................... ...................................... 1
.................. .................................. Gear Case ............................................................... ...................................... 1
.................. .................................. Bushing .................................................................... ...................................... 3
.................. .................................. Cover Pl ate .............................................................. ...................................... 1
2 ............... JLH160-2 ................... Spur Gear Assembly................................................ ...................................... 2
.................. .................................. Spur Gear ................................................................ ...................................... 2
.................. .................................. Pinion Gear .............................................................. ...................................... 2
3-2 ............. JLH160-3-2 ............... Driving Shaft
4 ................ JLH160-4 ................... Load Gear ................................................................ ...................................... 1
5 ................ JLH160-5 ................... Gear Side Plate Assembly ....................................... ...................................... 1
.................. .................................. Gear Side Plate ....................................................... ...................................... 1
.................. .................................. Bushing .................................................................... ...................................... 2
6 ................ JLH160-6 ................... Caged Roller Bearings ............................................ Ø30xØ40x13mm ........... 2
7 ................ JLH160-7 ................... Load Sheave ........................................................... ...................................... 1
8 ................ JLH160-8 ................... Guide Roller ............................................................. ...................................... 2
9 ................ JLH160-9 ................... Stripper .................................................................... ...................................... 1
10 .............. JLH160-10 ................. Lever Side Plate Assembly ...................................... ...................................... 1
.................. .................................. Lever Side Plate ...................................................... ...................................... 1
.................. .................................. Stay Bolt .................................................................. ...................................... 4
.................. .................................. Pawl Pin ................................................................... ...................................... 2
11 .............. JLH160-11 ................. Pawl Spring.............................................................. ...................................... 2
12 .............. JLH160-12 ................. Pawl (0.75, 1, 1.5 Ton) ............................................ ...................................... 2
13 .............. JLH160-13 ................. Snap Ring (0.75, 1, 1.5, 2.5 Ton) ............................ Ø 9mm .......................... 2
14 .............. JLH160-14 ................. Disc Hub (0.75, 1, 1.5, 2.5 Ton)............................... ...................................... 1
15 .............. JLH160-15 ................. Ratchet Disc (0.75, 1, 1.5, 2.5 Ton) ......................... ...................................... 1
16-1 ........... JLH160-16-1 ............. Brake Cover Assembly ............................................ ...................................... 1
................. .................................. Brake Cover ............................................................. ...................................... 1
.................. .................................. Handle Case ............................................................ ...................................... 1
................. .................................. Bushing .................................................................... ...................................... 1
.................. .................................. Thread Housing ....................................................... ...................................... 1
17-1 ........... JLH160-17G .............. Acorn Nut (0.75, 1, 1.5, 2.5 Ton) ............................. M6 ................................. 2
17A ............ JLH160-17AG ........... Lock Washer (0.75, 1, 1.5, 2.5 Ton) ........................ 6mm .............................. 2
18 ............. JLH80-18G ................ Lock Washer (0.75 to 9 Ton) ................................... 8mm .............................. 8
19 .............. JLH80-19G ................ Acorn Nut (0.75 to 9 Ton) ........................................ M8 ................................. 8
20-2 ........... JLH160-20-2 ............. Change Over Gear (0.75, 1, 1.5, 2.5 Ton) ............... ...................................... 1
20-2L ......... JLH160-20L-2 ........... Overload Limiter Assembly ...................................... ...................................... 1
.................. .................................. Overload Limiting Plate ........................................... ...................................... 1
.................. .................................. Change Over Gear .................................................. ...................................... 1
.................. .................................. Pressure Plate ......................................................... ...................................... 1
.................. .................................. Dish Spring .............................................................. ...................................... 1
.................. .................................. Washer .................................................................... ...................................... 1
.................. .................................. Lock Washer ............................................................ ...................................... 1
.................. .................................. Round Nut ............................................................... M30x1 ........................... 1
21 .............. JLH160-21 ................. Change Over Pawl (0.75, 1, 1.5, 2.5 Ton) ............... ...................................... 1
22 .............. JLH160-22 ................. Spring Shaft (0.75, 1, 1.5, 2.5 Ton) ......................... ...................................... 1
23 .............. JLH160-23 ................. Spring (0.75, 1, 1.5, 2.5 Ton) ................................... ...................................... 1
24-1 ........... JLH80-24-1 ............... Lever Handle Assembly(0.75, 1, 1.5, 2.5 Ton) ........ ...................................... 1
.................. .................................. Lever Handle ........................................................... ...................................... 1
.................. .................................. Selector Lever.......................................................... ...................................... 1
.................. .................................. Change Over Shaft .................................................. ...................................... 1
.................. .................................. Bolt........................................................................... ...................................... 2
.................. .................................. Spring Seat .............................................................. ...................................... 1
.................. .................................. Bushing .................................................................... ...................................... 1
24A-1 ......... JLH80-24A-1 ............. Rubber Grip (0.75, 1, 1.5, 2.5 Ton) ......................... ...................................... 1
25 .............. JLH160-25G .............. Socket Head Cap Screw (0.75, 1, 1.5, 2.5 Ton) ...... M6 x 12 ......................... 1
25A ............ JLH160-25AG ........... Lock Washer (0.75, 1, 1.5 Ton) ............................... 6mm .............................. 1
26-2 ........... JLH160-26-2A ........... Stop Knob (0.75, 1, 1.5, 2.5 Ton)
27-1 ........... JLH160-27-1 ............. Twisting Spring I (0.75, 1, 1.5, 2.5 Ton) .................. ...................................... 1
............................................................... ...................................... 1
.............................. ...................................... 1
17
Index No. Part No. Description Size Qty
28-2 ........... JLH160-28-2 ............. Hand Wheel Assembly (0.75, 1, 1.5, 2.5 Ton) ......... ...................................... 1
.................. .................................. Hand W heel ............................................................. ...................................... 1
.................. .................................. Steel Ball Spring ...................................................... ...................................... 2
.................. .................................. Steel Ball.................................................................. ...................................... 2
29-1 ........... JLH160-29-1 ............. Hand Wheel Cap (0.75, 1, 1.5, 2.5 Ton) .................. ...................................... 1
30-1 ........... JLH160-30-1 ............. Hand Wheel Base Assembly (0.75, 1, 1.5, 2.5 Ton) ...................................... 1
.................. .................................. Hand Wheel Base .................................................... ...................................... 1
.................. .................................. Bushing .................................................................... ...................................... 2
31-1 ........... F001754 .................... Lock Nut................................................................... M8 ................................. 1
32-1 ........... JLH80-32-1 ............... Steel Cable Ring (0.75 to 2.5Ton) ........................... ...................................... 1
33 .............. JLH80-33 ................... Rivet (0.75 to 9 Ton) ................................................ 3 x 6mm ........................ 6
34-1 ........... LM000193 ................. Name Plate JLH-160 ............................................... ...................................... 1
35 .............. F001755 .................... Lock Nut................................................................... M8 ................................. 1
36 .............. JLH160-36 ................. Bottom Hook Shaft .................................................. ...................................... 1
37 .............. JLH160-37-1 ............. Safety Latch Kit
.................. .................................. Safety Latch ............................................................. ...................................... 2
.................. .................................. Double Spring .......................................................... ...................................... 2
.................. .................................. Socket Cap Screw ................................................... M4 x 23 ......................... 2
.................. .................................. Lock Nut................................................................... M4 ................................. 2
38 ............. JLH160-38-1 ............. Bottom Hook Assembly (incls. 35 & 36) .................. ...................................... 1
.................. JLH160-38PH-1 ........ Bottom Point Hook Assembly (incls. 35 & 36) ......... ...................................... 1
.................. .................................. Bottom Hook ............................................................ ...................................... 1
.................. .................................. Safety Latch ............................................................. ...................................... 1
.................. .................................. Double Spring .......................................................... ...................................... 1
.................. .................................. Socket Cap Screw ................................................... M4 x 23 ......................... 1
.................. .................................. Lock Nut................................................................... M4 ................................. 1
.................. .................................. Bottom Hook Holder ................................................ ...................................... 2
.................. .................................. Rivet......................................................................... 6 x 24mm ...................... 4
39 .............. JLH160-39 ................. Top Hook Shaft ........................................................ ...................................... 1
40 .............. JLH160-40-1 ............. Top Hook Assembly................................................. ...................................... 1
.................. JLH160-40PH-1 ........ Top Point Hook Assembly
.................. .................................. Top Hook ................................................................. ...................................... 1
.................. .................................. Safety Latch ............................................................. ...................................... 1
.................. .................................. Double Spring .......................................................... ...................................... 1
.................. .................................. Socket Cap Screw ................................................... M4 x 23 ......................... 1
.................. .................................. Lock Nut................................................................... M4 ................................. 1
.................. .................................. Top Hook Holder...................................................... ...................................... 2
.................. .................................. Rivet......................................................................... 6 x 24mm ...................... 2
41 .............. JLH160-41 ................. Chain Stop ............................................................... ...................................... 1
42 .............. JLH160-42 ................. Drive Shaft Washer.................................................. ...................................... 1
49 .............. JLH160-49 ................. Load Chain – specify length .................................... #100,Ø7.1 x 19.9mm .... 1
50 .............. JLH160-50 ................. Rubber Grip Fastening (0.75, 1, 1.5, 2.5 Ton) ......... ...................................... 1
50A ............ JLH160-50A .............. Fastening Screw (0.75, 1, 1.5, 2.5 Ton) .................. ...................................... 1
.................. JLH-5027WL ............. Warning Label (not shown) ...................................... 50x27mm ...................... 1
52 .............. L100-WT ................... Warning Tag ............................................................ ...................................... 1
Note: Top and bottom hooks are sold as an assembly only. Both standard and point hooks are available for the 1.5 ton model, as listed above.
When ordering replacement chain (#49), specify length.
.......................................................... ........................................ 2
......................................... ........................................ 1
18

16.5 Parts List: JLH-250WO (2.5 Ton)

Non-numbered parts listed under each assembly are parts that make up that assembly.
Index No. Part No. Description Size Qty
1 ................ JLH250-1G ................ Gear Case Assembly ............................................... ...................................... 1
.................. .................................. Gear Case ............................................................... ...................................... 1
.................. .................................. Bushing .................................................................... ...................................... 3
.................. .................................. Cover Pl ate .............................................................. ...................................... 1
2 ............... JLH250-2 ................... Spur Gear Assembly................................................ ...................................... 2
.................. .................................. Spur Gear ................................................................ ...................................... 2
.................. .................................. Pinion Gear .............................................................. ...................................... 2
3-2 ............. JLH250-3-2 ............... Driving Shaft ............................................................ ...................................... 1
4 ................ JLH250-4 ................... Load Gear ................................................................ ...................................... 1
5 ................ JLH250-5 ................... Gear Side Plate Assembly ....................................... ...................................... 1
.................. .................................. Gear Side Plate ....................................................... ...................................... 1
.................. .................................. Bushing .................................................................... ...................................... 2
6 ................ JLH250-6 ................... Caged Roller Bearings ............................................ Ø35xØ45x14mm ........... 2
7 ................ JLH250-7 ................... Load Sheave ........................................................... ...................................... 1
8 ................ JLH250-8 ................... Guide Roller ............................................................. ...................................... 2
9 ................ JLH250-9 ................... Stripper .................................................................... ...................................... 1
10 .............. JLH250-10 ................. Lever Side Plate Assembly ...................................... ...................................... 1
.................. .................................. Lever Side Plate ...................................................... ...................................... 1
.................. .................................. Stay Bolt .................................................................. ...................................... 4
.................. .................................. Pawl Pin ................................................................... ...................................... 2
11 .............. JLH250-11 ................. Pawl Spring.............................................................. ...................................... 2
12 .............. JLH250-12 ................. Pawl ......................................................................... ...................................... 2
13 .............. JLH160-13 ................. Snap Ring (0.75, 1, 1.5, 2.5 Ton) ............................ Ø 9mm .......................... 2
14 .............. JLH160-14 ................. Disc Hub (0.75, 1, 1.5. 2.5 Ton)............................... ...................................... 1
15 .............. JLH160-15 ................. Ratchet Disc (0.75, 1, 1.5, 2.5 Ton) ......................... ...................................... 1
16-1 ........... JLH250-16-1 ............. Brake Cover Assembly ............................................ ...................................... 1
................. .................................. Brake Cover ............................................................. ...................................... 1
.................. .................................. Handle Case ............................................................ ...................................... 1
................. .................................. Bushing .................................................................... ...................................... 1
.................. .................................. Thread Housing ....................................................... ...................................... 1
17-1 ........... JLH160-17G .............. Acorn Nut (0.75, 1, 1.5, 2.5 Ton) ............................. M6 ................................. 2
17A ............ JLH160-17AG ........... Lock Washer (0.75, 1, 1.5, 2.5 Ton) ........................ 6mm .............................. 2
18 ............. JLH80-18G ................ Lock Washer (0.75 to 9 Ton) ................................... 8mm .............................. 8
19 .............. JLH80-19G ................ Acorn Nut (0.75 to 9 Ton) ........................................ M8 ................................. 8
20-2 ........... JLH160-20-2 ............. Change Over Gear (0.75, 1, 1.5, 2.5 Ton) ............... ...................................... 1
20-2L ......... JLH250-20L-2 ........... Overload Limiter Assembly ...................................... ...................................... 1
.................. .................................. Overload Limiting Plate ........................................... ...................................... 1
.................. .................................. Change Over Gear .................................................. ...................................... 1
.................. .................................. Pressure Plate ......................................................... ...................................... 1
.................. .................................. Dish Spring .............................................................. ...................................... 1
.................. .................................. Washer .................................................................... ...................................... 1
.................. .................................. Lock Washer ............................................................ ...................................... 1
.................. .................................. Round Nut ............................................................... M30x1 ........................... 1
21 .............. JLH160-21 ................. Change Over Pawl (0.75, 1, 1.5, 2.5 Ton) ............... ...................................... 1
22 .............. JLH160-22 ................. Spring Shaft (0.75, 1, 1.5, 2.5 Ton) ......................... ...................................... 1
23 .............. JLH160-23 ................. Spring (0.75, 1, 1.5, 2.5 Ton) ................................... ...................................... 1
24-1 ........... JLH80-24-1 ............... Lever Handle Assembly ........................................... ................
.................. .................................. Lever Handle ........................................................... ...................................... 1
.................. .................................. Selector Lever.......................................................... ...................................... 1
.................. .................................. Change Over Shaft .................................................. ...................................... 1
.................. .................................. Bolt........................................................................... ...................................... 2
.................. .................................. Spring Seat .............................................................. ...................................... 1
.................. .................................. Bushing .................................................................... ...................................... 1
24A-1 ......... JLH80-24A-1 ............. Rubber Grip (0.75, 1, 1.5, 2.5 Ton)s ........................ ...................................... 1
25 .............. JLH160-25G .............. Socket Head Cap Screw (0.75, 1, 1.5, 2.5 Ton) ...... M6 x 12 ......................... 1
25A ............ F002111 .................... Lock Washer (2.5, 3, 6 Ton) .................................... 6mm .............................. 1
26-2 ........... JLH160-26-2A ........... Stop Knob (0.75, 1, 1.5, 2.5 Ton)
27-1 ........... JLH160-27-1 ............. Twisting Spring (0.75, 1, 1.5, 2.5 Ton) .................... ...................................... 1
.............................. ...................................... 1
19
...................... 1
Index No. Part No. Description Size Qty
28-2 ........... JLH160-28-2 ............. Hand Wheel Assembly (0.75, 1, 1.5, 2.5 Ton) ......... ...................................... 1
.................. .................................. Hand W heel ............................................................. ...................................... 1
.................. .................................. Steel Ball Spring ...................................................... ...................................... 2
.................. .................................. Steel Ball.................................................................. ...................................... 2
29-1 ........... JLH160-29-1 ............. Hand Wheel Cap (0.75, 1, 1.5, 2.5 Ton) .................. ...................................... 1
30-1 ........... JLH160-30-1 ............. Hand Wheel Base Assembly (0.75, 1, 1.5, 2.5 Ton) ...................................... 1
.................. .................................. Hand Wheel Base .................................................... ...................................... 1
.................. .................................. Bushing .................................................................... ...................................... 2
31-1 ........... F001754 .................... Lock Nut................................................................... M8 ................................. 1
32-1 ........... JLH80-32-1 ............... Steel Cable Ring (0.75 to 2.5 Ton) .......................... ...................................... 1
33 .............. JLH80-33 ................... Rivet (0.75 to 2.5 Ton) ............................................. 3 x 6mm ........................ 6
34-1 ........... LM000194 ................. Name Plate JLH-250 ............................................... ...................................... 1
35 .............. F001755 .................... Lock Nut................................................................... M10 ............................... 1
36 .............. JLH250-36 ................. Bottom Hook Shaft .................................................. ...................................... 1
37 .............. JLH250-37-1 ............. Safety Latch Kit ....................................................... ...................................... 2
.................. .................................. Safety Latch ............................................................. ...................................... 2
.................. .................................. Double Spring .......................................................... ...................................... 2
.................. .................................. Socket Cap Screw ................................................... M6 x 33 ......................... 2
.................. .................................. Lock Nut................................................................... M6 ................................. 2
38 ............. JLH250-38-1 ............. Bottom Hook Assembly (incls. 35 & 36) .................. ...................................... 1
.................. .................................. Bottom Hook ............................................................ ...................................... 1
.................. .................................. Safety Latch ............................................................. ...................................... 1
.................. .................................. Double Spring .......................................................... ...................................... 1
.................. .................................. Socket Cap Screw ................................................... M6 x 33 ......................... 1
.................. .................................. Lock Nut................................................................... M6 ................................. 1
.................. .................................. Bottom Hook Holder ................................................ ...................................... 2
.................. .................................. Rivet......................................................................... 7 x 25mm ...................... 4
39 .............. JLH250-39 ................. Top Hook Shaft ........................................................ ...................................... 1
40 .............. JLH250-40-1 ............. Top Hook Assembly
................................................... ........................................ 1
.................. .................................. Top Hook ................................................................. ...................................... 1
.................. .................................. Safety Latch ............................................................. ...................................... 1
.................. .................................. Double Spring .......................................................... ...................................... 1
.................. .................................. Socket Cap Screw ................................................... M6 x 33 ......................... 1
.................. .................................. Lock Nut................................................................... M6 ................................. 1
.................. .................................. Top Hook Holder...................................................... ...................................... 2
.................. .................................. Rivet......................................................................... 7 x 25mm ...................... 2
41 .............. JLH250-41 ................. Chain Stop ............................................................... ...................................... 1
42 .............. JLH250-42 ................. Drive Shaft Washer.................................................. ...................................... 1
49 .............. JLH250-49 ................. Load Chain – specify length .................................... #100,Ø8.8 x 24.6mm .... 1
50 .............. JLH160-50 ................. Rubber Grip Fastening (0.75, 1, 1.5, 2.5 Ton) ......... ...................................... 1
50A ............ JLH160-50A .............. Fastening Screw (0.75, 1, 1.5, 2.5 Ton) .................. ...................................... 1
.................. JLH-7040WL ............. Warning Label (not shown) ...................................... 70x40mm ...................... 1
52 .............. L100-WT ................... Warning Tag ............................................................ ...................................... 1
Note: Top and bottom hooks are sold as an assembly only.
When ordering replacement chain (#49), specify length.
20

16.6 Parts List: JLH-300WO (3 Ton)

Non-numbered parts listed under each assembly are parts that make up that assembly.
Index No. Part No. Description Size Qty
1 ................ JLH320-1G ................ Gear Case Assembly (3, 6, 9 Ton) .......................... ...................................... 1
.................. .................................. Gear Case ............................................................... ...................................... 1
.................. .................................. Bushing .................................................................... ...................................... 3
.................. .................................. Cover Pl ate .............................................................. ...................................... 1
2 ............... JLH320-2 ................... Spur Gear Assembly (3, 6, 9 Ton) ........................... ...................................... 2
.................. .................................. Spur Gear ................................................................ ...................................... 2
.................. .................................. Pinion Gear .............................................................. ...................................... 2
3-2 ............. JLH320-3-2 ............... Driving Shaft (3, 6, 9 Ton)
4 ................ JLH320-4 ................... Load Gear (3, 6, 9 Ton) ........................................... ...................................... 1
5 ................ JLH320-5 ................... Gear Side Plate Assembly (3, 6, 9 Ton) .................. ...................................... 1
.................. .................................. Gear Side Plate ....................................................... ...................................... 1
.................. .................................. Bushing .................................................................... ...................................... 2
6 ................ JLH320-6 ................... Caged Roller Bearings (3, 6, 9 Ton) ........................ Ø40xØ50x15mm ........... 2
7 ................ JLH320-7 ................... Load Sheave (3, 6, 9 Ton) ....................................... ...................................... 1
8 ................ JLH320-8 ................... Guide Roller (3, 6, 9 Ton) ........................................ ...................................... 2
9 ................ JLH320-9 ................... Stripper (3, 6, 9 Ton)................................................ ...................................... 1
10 .............. JLH320-10 ................. Lever Side Plate Assembly (3, 6, 9 Ton) ................. ...................................... 1
.................. .................................. Lever Side Plate ...................................................... ...................................... 1
.................. .................................. Stay Bolt .................................................................. ...................................... 4
.................. .................................. Pawl Pin ................................................................... ...................................... 2
11 .............. JLH320-11 ................. Pawl Spring (3, 6, 9 Ton) ......................................... ...................................... 2
12 .............. JLH320-12 ................. Pawl (3, 6, 9 Ton) .................................................... ...................................... 2
13 .............. JLH320-13 ................. Snap Ring (3, 6, 9 Ton) ........................................... Ø 10mm ........................ 2
14 .............. JLH320-14 ................. Disc Hub (3, 6, 9 Ton).............................................. ...................................... 1
15 .............. JLH320-15 ................. Ratchet Disc (3, 6, 9 Ton) ........................................ ...................................... 1
16-1 ........... JLH320-16-1 ............. Brake Cover Assembly (3, 6, 9 Ton) ....................... ...................................... 1
................. .................................. Brake Cover ............................................................. ...................................... 1
.................. .................................. Handle Case ............................................................ ...................................... 1
................. .................................. Bushing .................................................................... ...................................... 1
.................. .................................. Thread Housing ....................................................... ...................................... 1
17-1 ........... JLH320-17G .............. Acorn Nut (3, 6, 9 Ton) ............................................ M8 ................................. 2
17A ............ JLH320-17AG ........... Lock Washer (3, 6, 9 Ton) ....................................... 8mm .............................. 2
18 ............. JLH80-18G ................ Lock Washer (0.75 to 9 Ton) ................................... 8mm .............................. 8
19 .............. JLH80-19G ................ Acorn Nut (0.75 to 9 Ton) ........................................ M8 ................................. 8
20-2 ........... JLH320-20-2 ............. Change Over Gear (3, 6, 9 Ton) .............................. ...................................... 1
20-2L ......... JLH320-20L-2 ........... Overload Limiter Assembly ...................................... ...................................... 1
.................. .................................. Overload Limiting Plate ........................................... ...................................... 1
.................. .................................. Change Over Gear .................................................. ...................................... 1
.................. .................................. Pressure Plate ......................................................... ...................................... 1
.................. .................................. Dish Spring .............................................................. ...................................... 1
.................. .................................. Washer .................................................................... ...................................... 1
.................. .................................. Lock Washer ............................................................ ...................................... 1
.................. .................................. Round Nut ............................................................... M30x1 ........................... 1
21 .............. JLH320-21 ................. Change Over Pawl (3, 6, 9 Ton) .............................. ...................................... 1
22 .............. JLH320-22 ................. Spring Shaft (3, 6, 9 Ton) ........................................ ...................................... 1
23 .............. JLH320-23 ................. Spring (3, 6, 9 Ton) .................................................. ...................................... 1
24-1 ........... JLH320-24-1 ............. Lever Handle Assembly (3, 6, 9 Ton) ...................... ...................................... 1
.................. .................................. Lever Handle ........................................................... ...................................... 1
.................. .................................. Selector Lever.......................................................... ...................................... 1
.................. .................................. Change Over Shaft .................................................. ...................................... 1
.................. .................................. Bolt........................................................................... ...................................... 2
.................. .................................. Spring Seat ...........................................................
.................. .................................. Bushing .................................................................... ...................................... 1
24A-1 ......... JLH320-24A-1 ........... Rubber Grip (3, 6, 9 Ton)......................................... ...................................... 1
25 .............. JLH320-25G .............. Socket Head Cap Screw (3, 6, 9 Ton) ..................... M8 x 16 ......................... 1
25A ............ JLH320-25AG ........... Lock Washer (2.5, 3, 6, 9 Ton) ................................ 8mm .............................. 1
26-2 ........... JLH320-26-2A ........... Stop Knob (3, 6, 9 Ton)
27-1 ........... JLH320-27-1 ............. Twisting Spring (3, 6, 9 Ton)................................... ...................................... 1
.......................................... ...................................... 1
... ...................................... 1
.............................................. ...................................... 1
21
Index No. Part No. Description Size Qty
28-2 ........... JLH320-28-2 ............. Hand Wheel Assembly (3, 6, 9 Ton) ........................ ...................................... 1
.................. .................................. Hand W heel ............................................................. ...................................... 1
.................. .................................. Steel Ball Spring ...................................................... ...................................... 2
.................. .................................. Steel Ball.................................................................. ...................................... 2
29-1 ........... JLH320-29-1 ............. Hand Wheel Cap (3, 6, 9 Ton) ................................. ...................................... 1
30-1 ........... JLH320-30-1 ............. Hand Wheel Base Assembly (3, 6, 9 Ton)............... ...................................... 1
.................. .................................. Hand Wheel Base .................................................... ...................................... 1
.................. .................................. Bushing .................................................................... ...................................... 2
31-1 ........... F001755 .................... Lock Nut................................................................... M10 ............................... 1
32-1 ........... JLH320-32-1 ............. Steel Cable Ring (3 to 9 Ton) .................................. ...................................... 1
33 .............. JLH80-33 ................... Rivet (0.75 to 9 Ton) ................................................ 3 x 6mm ........................ 4
34-1 ........... LM000195 ................. Name Plate JLH-300 ............................................... ...................................... 1
35 .............. F001755 .................... Lock Nut................................................................... M10 ............................... 1
36 .............. JLH320-36 ................. Bottom Hook Shaft .................................................. ...................................... 1
37 .............. JLH320-37-1 ............. Safety Latch Kit ....................................................... ...................................... 2
.................. .................................. Safety Latch ............................................................. ...................................... 2
.................. .................................. Double Spring .......................................................... ...................................... 2
.................. .................................. Socket Cap Screw ................................................... M6 x 33 ......................... 2
.................. .................................. Lock Nut................................................................... M6 ................................. 2
38 ............. JLH320-38-1 ............. Bottom Hook Assembly (incls. 35 & 36) .................. ...................................... 1
.................. JLH320-38PH-1 ........ Bottom Point Hook Assembly (incls. 35 & 36) ......... ...................................... 1
.................. .................................. Bottom Hook ............................................................ ...................................... 1
.................. .................................. Safety Latch ............................................................. ...................................... 1
.................. .................................. Double Spring .......................................................... ...................................... 1
.................. .................................. Socket Cap Screw ................................................... M6 x 33 ......................... 1
.................. .................................. Lock Nut................................................................... M6 ................................. 1
.................. .................................. Bottom Hook Holder ................................................ ...................................... 2
.................. .................................. Rivet......................................................................... 7 x 25mm ...................... 4
39 .............. JLH320-39 ................. Top Hook Shaft (3, 6, 9 Ton) ................................... ...................................... 1
40 .............. JLH320-40 ................. Top Hook Assembly................................................. ...................................... 1
.................. JLH320-40PH-1 ........ Top Point Hook Assembly ....................................... ...................................... 1
.................. .................................. Top Hook ................................................................. ...................................... 1
.................. .................................. Safety Latch ............................................................. ...................................... 1
.................. .................................. Double Spring .......................................................... ...................................... 1
.................. .................................. Socket Cap Screw ................................................... M6 x 33 ......................... 1
.................. .................................. Lock Nut................................................................... M6 ................................. 1
.................. .................................. Top Hook Holder...................................................... ...................................... 2
.................. .................................. Rivet......................................................................... 7 x 25mm ...................... 2
41 .............. JLH320-41 ................. Chain Stop (3, 6, 9 Ton) .......................................... ...................................... 1
42 .............. JLH320-42 ................. Drive Shaft Washer (3, 6, 9 Ton) ............................. ...................................... 1
49 .............. JLH320-49 ................. Load Chain (3, 6, 9 Ton) – specify length ................ #100,Ø10 x 18mm ........ 1
50 .............. JLH320-50 ................. Rubber Grip Fastening (3, 6, 9 Ton) ........................ ...................................... 1
50A ............ JLH320-50A .............. Fastening Screw (3, 6, 9 Ton) ................................. ...................................... 1
.................. JLH-7040WL ............. Warning Label (not shown) ...................................... 70x40mm ...................... 1
52 .............. L100-WT ................... Warning Tag ............................................................ ...................................... 1
Note: Top and bottom hooks are sold as an assembly only. Both standard and point hooks are available for the 3 ton model, as listed above.
When ordering replacement chain (#49), specify length.
22

16.7 Parts List: JLH-600WO (6 Ton)

Non-numbered parts listed under each assembly are parts that make up that assembly.
Index No. Part No. Description Size Qty
1 ................ JLH320-1G ................ Gear Case Assembly (3, 6, 9 Ton) .......................... ...................................... 1
.................. .................................. Gear Case ............................................................... ...................................... 1
.................. .................................. Bushing .................................................................... ...................................... 3
.................. .................................. Cover Pl ate .............................................................. ...................................... 1
2 ............... JLH320-2 ................... Spur Gear Assembly (3, 6, 9 Ton) ........................... ...................................... 2
.................. .................................. Spur Gear ................................................................ ...................................... 2
.................. .................................. Pinion Gear .............................................................. ...................................... 2
3-2 ............. JLH320-3-2 ............... Driving Shaft (3, 6, 9 Ton)........................................ ...................................... 1
4 ................ JLH320-4 ................... Load Gear (3, 6, 9 Ton) ........................................... ...................................... 1
5 ................ JLH320-5 ................... Gear Side Plate Assembly (3, 6, 9 Ton) .................. ...................................... 1
.................. .................................. Gear Side Plate ....................................................... ...................................... 1
.................. .................................. Bushing .................................................................... ...................................... 2
6 ................ JLH320-6 ................... Caged Roller Bearings (3, 6, 9 Ton) ........................ Ø40xØ50x15mm ........... 2
7 ................ JLH320-7 ................... Load Sheave (3, 6, 9 Ton) ....................................... ...................................... 1
8 ................ JLH320-8 ................... Guide Roller (3, 6, 9 Ton) ........................................ ...................................... 2
9 ................ JLH320-9 ................... Stripper (3, 6, 9 Ton)................................................ ...................................... 1
10 .............. JLH320-10 ................. Lever Side Plate Assembly (3, 6, 9 Ton) ................. ...................................... 1
.................. .................................. Lever Side Plate ...................................................... ...................................... 1
.................. .................................. Stay Bolt .................................................................. ...................................... 4
.................. .................................. Pawl Pin ................................................................... ...................................... 2
11 .............. JLH320-11 ................. Pawl Spring (3, 6, 9 Ton) ......................................... ...................................... 2
12 .............. JLH320-12 ................. Pawl (3, 6, 9 Ton) .................................................... ...................................... 2
13 .............. JLH320-13 ................. Snap Ring (3, 6, 9 Ton) ........................................... Ø 10mm ........................ 2
14 .............. JLH320-14 ................. Disc Hub (3, 6, 9 Ton).............................................. ...................................... 1
15 .............. JLH320-15 ................. Ratchet Disc (3, 6, 9 Ton) ........................................ ...................................... 1
16-1 ........... JLH320-16-1 ............. Brake Cover Assembly (3, 6, 9 Ton) ....................... ...................................... 1
................. .................................. Brake Cover ............................................................. ...................................... 1
.................. .................................. Handle Case ............................................................ ...................................... 1
................. .................................. Bushing .................................................................... ...................................... 1
.................. .................................. Thread Housing ....................................................... ...................................... 1
17-1 ........... JLH320-17G .............. Acorn Nut (3, 6, 9 Ton) ............................................ M8 ................................. 2
17A ............ JLH320-17AG ........... Lock Washer (3, 6, 9 Ton) ....................................... 8mm .............................. 2
18 ............. JLH80-18G ................ Lock Washer (0.75 to 9 Ton) ................................... 8mm .............................. 8
19 .............. JLH80-19G ................ Acorn Nut (0.75 to 9 Ton) ........................................ M8 ................................. 8
20-2 ........... JLH320-20-2 ............. Change Over Gear (3, 6, 9 Ton) .............................. ...................................... 1
20-2L ......... JLH630-20L-2 ........... Overload Limiter Assembly ...................................... ...................................... 1
.................. .................................. Overload Limiting Plate ........................................... ...................................... 1
.................. .................................. Change Over Gear .................................................. ...................................... 1
.................. .................................. Pressure Plate ......................................................... ...................................... 1
.................. .................................. Dish Spring .............................................................. ...................................... 1
.................. .................................. Washer .................................................................... ...................................... 1
.................. .................................. Lock Washer ............................................................ ...................................... 1
.................. .................................. Round Nut ............................................................... M30x1 ........................... 1
21 .............. JLH320-21 ................. Change Over Pawl (3, 6, 9 Ton) .............................. ...................................... 1
22 .............. JLH320-22 ................. Spring Shaft (3, 6, 9 Ton) ........................................ ...................................... 1
23 .............. JLH320-23 ................. Spring (3, 6, 9 Ton) .................................................. ...................................... 1
24-1 ........... JLH320-24-1 ............. Lever Handle Assembly (3, 6, 9 Ton) ...................... ...................................... 1
.................. .................................. Lever Handle ........................................................... ...................................... 1
.................. .................................. Selector Lever.......................................................... ...................................... 1
.................. .................................. Change Over Shaft .................................................. ...................................... 1
.................. .................................. Bolt........................................................................... ...................................... 2
.................. .................................. Spring Seat .............................................................. ...................................... 1
.................. .................................. Bushing .................................................................... ...................................... 1
24A-1 ......... JLH320-24A-1 ........... Rubber Grip (3, 6, 9 Ton)......................................... ...................................... 1
25 .............. JLH320-25G .............. Socket Head Cap Screw (3, 6, 9 Ton) ..................... M8 x 16 ......................... 1
25A ............ JLH320-25AG ........... Lock Washer (2.5, 3, 6, 9 Ton) ................................ 8mm .............................. 1
26-2 ........... JLH320-26-2A ........... Stop Knob (3, 6, 9 Ton)
27-1 ........... JLH320-27-1 ............. Twisting Spring (3, 6 , 9Ton).................................... ...................................... 1
.............................................. ...................................... 1
23
Index No. Part No. Description Size Qty
28-2 ........... JLH320-28-2 ............. Hand Wheel Assembly (3, 6, 9 Ton) ........................ ...................................... 1
.................. .................................. Hand W heel ............................................................. ...................................... 1
.................. .................................. Steel Ball Spring ...................................................... ...................................... 2
.................. .................................. Steel Ball.................................................................. ...................................... 2
29-1 ........... JLH320-29-1 ............. Hand Wheel Cap (3, 6, 9 Ton) ................................. ...................................... 1
30-1 ........... JLH320-30-1 ............. Hand Wheel Base Assembly (3, 6, 9 Ton)............... ...................................... 1
.................. .................................. Hand Wheel Base .................................................... ...................................... 1
.................. .................................. Bushing .................................................................... ...................................... 2
31-1 ........... F001755 .................... Lock Nut................................................................... M10 ............................... 1
32-1 ........... JLH80-32-1 ............... Steel Cable Ring (3 to 9 Ton) .................................. ...................................... 1
33 .............. JLH80-33 ................... Rivet (0.75 to 9 Ton) ................................................ 3 x 6mm ........................ 4
34-1 ........... LM000196 ................. Name Plate JLH-600 ............................................... ...................................... 1
37 .............. JLH630-37-1 ............. Safety Latch Kit ....................................................... ...................................... 2
.................. .................................. Safety Latch ............................................................. ...................................... 2
.................. .................................. Double Spring .......................................................... ...................................... 2
.................. .................................. Socket Cap Screw ................................................... M6 x 33 ......................... 2
.................. .................................. Lock Nut................................................................... M6 ................................. 2
38 ............. JLH630-38-1 ............. Bottom Hook Assembly (incls. 35 & 36)
.................. .................................. Bottom Hook ............................................................ ...................................... 1
.................. .................................. Safety Latch ............................................................. ...................................... 1
.................. .................................. Double Spring .......................................................... ...................................... 1
.................. .................................. Socket Cap Screw ................................................... M6 x 33 ......................... 1
.................. .................................. Lock Nut................................................................... M6 ................................. 1
.................. .................................. Bottom Hook Holder ................................................ ...................................... 2
.................. .................................. Socket Cap Screw ................................................... M10 x 32 ....................... 3
.................. .................................. Lock Nut................................................................... M10 ............................... 3
.................. .................................. Straight Pin .............................................................. Ø8 x 18mm ................... 2
.................. .................................. Idle Shaft ................................................................. ...................................... 1
.................. .................................. Idle Sheave .............................................................. ...................................... 1
.................. .................................. Needle Bearing ........................................................ .................................... 29
39 .............. JLH320-39 ................. Top Hook Shaft (3, 6, 9 Ton) ................................... ...................................... 1
40 .............. JLH630-40-1 ............. Top Hook Assembly................................................. ...................................... 1
.................. .................................. Top Hook ................................................................. ...................................... 1
.................. .................................. Safety Latch ............................................................. ...................................... 1
.................. .................................. Double Spring .......................................................... ...................................... 1
.................. .................................. Socket Cap Screw ................................................... M6 x 33 ......................... 1
.................. .................................. Lock Nut................................................................... M6 ................................. 1
.................. .................................. Top Hook Holder...................................................... ...................................... 2
.................. .................................. Rivet......................................................................... 10 x 34mm .................... 3
41 .............. JLH320-41 ................. Chain Stop (3, 6, 9 Ton) .......................................... ...................................... 1
42 .............. JLH320-42 ................. Drive Shaft Washer (3, 6, 9 Ton) ............................. ...................................... 1
43 .............. JLH630-43 ................. Socket Cap Screw
44 .............. JLH630-44 ................. Straight Pin .............................................................. Ø8 x 18 ......................... 2
45 .............. JLH630-45 ................. Idle Shaft (6, 9T) ...................................................... ...................................... 1
46 .............. JLH630-46 ................. Idle Sheave (6, 9T) .................................................. ...................................... 1
47 .............. JLH630-47 ................. Chain Pin ................................................................. ...................................... 1
48 .............. F001755 .................... Lock Nut................................................................... M10 ............................... 1
49 .............. JLH320-49 ................. Load Chain (3, 6, 9 Ton) – specify length ................ #100,Ø10 x 28mm ........ 2
50 .............. JLH320-50 ................. Rubber Grip Fastening (3, 6, 9 Ton) ........................ ...................................... 1
50A ............ JLH320-50A .............. Fastening Screw (3, 6, 9 Ton) ................................. ...................................... 1
51 .............. JLH900-51 ................. Needle Bearing ........................................................ .................................... 29
.................. JLH-7040WL ............. Warning Label (not shown) ...................................... 70x40mm ...................... 1
52 .............. L100-WT ................... Warning Tag ............................................................ ...................................... 1
Note: Top and bottom hooks are sold as an assembly only.
When ordering replacement chain (#49), specify length.
(includes 43A nut, 43B washer) ... M10 x 30 ....................... 3
................... ...................................... 1
24

16.8 Parts List: JLH-900 (9 Ton)

Non-numbered parts listed under each assembly are parts that make up that assembly.
Index No. Part No. Description Size Qty
1 ................ JLH320-1G ................ Gear Case Assembly (3, 6, 9 Ton) .......................... ...................................... 1
.................. .................................. Gear Case ............................................................... ...................................... 1
.................. .................................. Bushing .................................................................... ...................................... 3
.................. .................................. Cover Pl ate .............................................................. ...................................... 1
2 ............... JLH320-2 ................... Spur Gear Assembly (3, 6, 9 Ton) ........................... ...................................... 2
.................. .................................. Spur Gear ................................................................ ...................................... 2
.................. .................................. Pinion Gear .............................................................. ...................................... 2
3-2 ............. JLH320-3-2 ............... Driving Shaft (3, 6, 9 Ton)........................................ ...................................... 1
4 ................ JLH320-4 ................... Load Gear (3, 6 Ton) ............................................... ...................................... 1
5 ................ JLH320-5 ................... Gear Side Plate Assembly (3, 6, 9 Ton) .................. ...................................... 1
.................. .................................. Gear Side Plate ....................................................... ...................................... 1
.................. .................................. Bushing .................................................................... ...................................... 2
6 ................ JLH320-6 ................... Caged Roller Bearings (3, 6, 9 Ton) ........................ Ø40xØ50x15mm ........... 2
7 ................ JLH320-7 ................... Load Sheave (3, 6, 9 Ton) ....................................... ...................................... 1
8 ................ JLH320-8 ................... Guide Roller (3, 6, 9 Ton) ........................................ ...................................... 2
9 ................ JLH320-9 ................... Stripper (3, 6, 9 Ton)................................................ ...................................... 1
10 .............. JLH320-10 ................. Lever Side Plate Assembly (3, 6, 9 Ton) ................. ...................................... 1
.................. .................................. Lever Side Plate ...................................................... ...................................... 1
.................. .................................. Stay Bolt .................................................................. ...................................... 4
.................. .................................. Pawl Pin ................................................................... ...................................... 2
11 .............. JLH320-11 ................. Pawl Spring (3, 6, 9 Ton) ......................................... ...................................... 2
12 .............. JLH320-12 ................. Pawl (3, 6, 9 Ton) .................................................... ...................................... 2
13 .............. JLH320-13 ................. Snap Ring (3, 6, 9 Ton) ........................................... Ø 10mm ........................ 2
14 .............. JLH320-14 ................. Disc Hub (3, 6, 9 Ton).............................................. ...................................... 1
15 .............. JLH320-15 ................. Ratchet Disc (3, 6, 9 Ton) ........................................ ...................................... 1
16-1 ........... JLH320-16-1 ............. Brake Cover Assembly (3, 6, 9 Ton) ....................... ...................................... 1
................. .................................. Brake Cover ............................................................. ...................................... 1
.................. .................................. Handle Case ............................................................ ...................................... 1
................. .................................. Bushing .................................................................... ...................................... 1
.................. .................................. Thread Housing ....................................................... ...................................... 1
17-1 ........... JLH320-17G .............. Acorn Nut (3, 6, 9 Ton) ............................................ M8 ................................. 2
17A ............ JLH320-17AG ........... Lock Washer (3, 6, 9 Ton) ....................................... 8mm .............................. 2
18 ............. JLH80-18G ................ Lock Washer (0.75 to 9 Ton) ................................... 8mm .............................. 8
19 .............. JLH80-19G ................ Acorn Nut (0.75 to 9 Ton) ........................................ M8 ................................. 8
20-2 ........... JLH320-20-2 ............. Change Over Gear (3, 6, 9 Ton) ............................. ...................................... 1
20-2L ......... JLH900-20L-2 ........... Overload Limiter Assembly ...................................... ...................................... 1
.................. .................................. Overload Limiting Plate ........................................... ...................................... 1
.................. .................................. Change Over Gear .................................................. ...................................... 1
.................. .................................. Pressure Plate ......................................................... ...................................... 1
.................. .................................. Dish Spring .............................................................. ...................................... 1
.................. .................................. Washer .................................................................... ...................................... 1
.................. .................................. Lock Washer ............................................................ ...................................... 1
.................. .................................. Round Nut ............................................................... M30x1 ........................... 1
21 .............. JLH320-21 ................. Change Over Pawl (3, 6, 9 Ton) .............................. ...................................... 1
22 .............. JLH320-22 ................. Spring Shaft (3, 6, 9 Ton) ........................................ ...................................... 1
23 .............. JLH320-23 ................. Spring (3, 6, 9 Ton) .................................................. ...................................... 1
24-1 ........... JLH320-24-1 ............. Lever Handle Assembly (3, 6, 9 Ton) ...................... ...................................... 1
.................. .................................. Lever Handle ........................................................... ...................................... 1
.................. .................................. Selector Lever.......................................................... ...................................... 1
.................. .................................. Change Over Shaft .................................................. ...................................... 1
.................. .................................. Bolt........................................................................... ...................................... 2
.................. .................................. Spring Seat .............................................................. ...................................... 1
.................. .................................. Bushing .................................................................... ...................................... 1
24A-1 ......... JLH320-24A-1 ........... Rubber Grip (3, 6, 9 Ton)......................................... ...................................... 1
25 .............. JLH320-25G .............. Socket Head Cap Screw (3, 6, 9 Ton) ..................... M8 x 16 ......................... 1
25A ............ JLH320-25AG ........... Lock Washer (2.5, 3, 6, 9 Ton) ................................ 8mm .............................. 1
26-2 ........... JLH320-26-2A ........... Stop Knob (3, 6, 9 Ton) ........................................... ...................................... 1
27-1 ........... JLH320-27-1 ............. Twisting Spring (3, 6, 9 Ton).................................... ...................................... 1
25
Index No. Part No. Description Size Qty
28-2 ........... JLH320-28-2 ............. Hand Wheel (3, 6, 9 Ton) ........................................ ...................................... 1
.................. .................................. Hand W heel ............................................................. ...................................... 1
.................. .................................. Steel Ball Spring ...................................................... ...................................... 2
.................. .................................. Steel Ball.................................................................. ...................................... 2
29-1 ........... JLH320-29-1 ............. Hand Wheel Cap (3, 6, 9 Ton) ................................. ...................................... 1
30-1 ........... JLH320-30-1 ............. Hand Wheel Base Assembly (3, 6, 9 Ton)............... ...................................... 1
.................. .................................. Hand Wheel Base .................................................... ...................................... 1
.................. .................................. Bushing .................................................................... ...................................... 2
31-1 ........... F001755 .................... Lock Nut................................................................... M10 ............................... 1
32-1 ........... JLH80-32-1 ............... Steel Cable Ring (0.75 to 9 Ton) ............................. 2 x 18mm ...................... 1
33 .............. JLH80-33 ................... Rivet (0.75 to 9 Ton) ................................................ 3 x 6mm ........................ 4
34-1 ........... LM000197 ................. Name Plate JLH-900 ............................................... ...................................... 1
35 .............. F001755 .................... Lock Nut................................................................... M10 ............................... 1
36 .............. JLH900-35 ................. Chain Pin ................................................................. ...................................... 1
37 .............. JLH900-37-1 ............. Safety Latch Kit ....................................................... ...................................... 2
.................. .................................. Safety Latch ............................................................. ...................................... 2
.................. .................................. Double Spring .......................................................... ...................................... 2
.................. .................................. Socket Cap Screw ................................................... M6 x 33 ......................... 2
.................. .................................. Lock Nut................................................................... M6 ................................. 2
38 ............. JLH900-38-1 ............. Bottom Hook Assembly (incls. 35 & 36) .................. ...................................... 1
.................. .................................. Bottom Hook ............................................................ ...................................... 1
.................. .................................. Safety Latch ............................................................. ...................................... 1
.................. .................................. Double Spring .......................................................... ...................................... 1
.................. .................................. Socket Cap Screw ................................................... M6 x 33 ......................... 1
.................. .................................. Lock Nut................................................................... M6 ................................. 1
.................. .................................. Bottom Hook Holder ................................................ ...................................... 2
.................. .................................. Socket Cap Screw ................................................... M10 x 40 ....................... 3
.................. .................................. Lock Nut................................................................... M10 ............................... 3
.................. .................................. Straight Pin .............................................................. Ø8 x 18mm ................... 2
.................. .................................. Idle Shaft ................................................................. ...................................... 1
.................. .................................. Idle Sheave .............................................................. ...................................... 1
.................. .................................. Needle Bearing ........................................................ Ø3 x 40mm ................. 29
39 .............. JLH320-39 ................. Top Hook Shaft (3, 6, 9 Ton) ................................... ...................................... 1
40 .............. JLH900-40-1 ............. Top Hook Assembly................................................. ...................................... 1
.................. .................................. Top Hook ................................................................. ...................................... 1
.................. .................................. Safety Latch ............................................................. ...................................... 1
.................. .................................. Double Spring .......................................................... ...................................... 1
.................. .................................. Socket Cap Screw ................................................... M6 x 33 ......................... 1
.................. .................................. Lock Nut................................................................... M6 ................................. 1
.................. .................................. Top Hook Holder...................................................... ...................................... 2
.................. .................................. Socket Cap Screw ................................................... M10x40 ......................... 2
.................. .................................. Lock Nut................................................................... M10 ............................... 2
.................. .................................. Straight Pin .............................................................. Ø8 x 18mm ................... 2
.................. .................................. Idle Shaft ................................................................. ...................................... 1
.................. .................................. Idle Sheave .............................................................. ...................................... 1
.................. .................................. Needle Bearing ........................................................ Ø3 x 40mm ................. 29
41 .............. JLH320-41 ................. Chain Stop (3, 6, 9 Ton) .......................................... ...................................... 1
42 .............. JLH320-42
43 .............. JLH630-43 ................. Socket Cap Screw
44 .............. JLH630-44 ................. Straight Pin .............................................................. Ø8 x 18 ......................... 2
45 .............. JLH630-45 ................. Idle Shaft (6, 9 Ton) ................................................. ...................................... 1
46 .............. JLH630-46 ................. Idle Sheave (6, 9 Ton) ............................................. ...................................... 1
49 .............. JLH320-49 ................. Load Chain (3, 6, 9 Ton) – specify length ................ #100,Ø10 x 28mm ........ 3
50 .............. JLH320-50 ................. Rubber Grip Fastening (3, 6, 9 Ton) ........................ ...................................... 1
50A ............ JLH320-50A .............. Fastening Screw (3, 6, 9 Ton) ................................. ...................................... 1
51 .............. JLH900-51 ................. Needle Bearing ........................................................ ................................ 2x29
.................. JLH-7040WL ............. Warning Label (not shown) ...................................... 70x40mm ...................... 1
52 .............. L100-WT ................... Warning Tag ............................................................ ...................................... 1
Note: Top and bottom hooks are sold as an assembly only.
When ordering replacement chain (#49), specify length.
................. Drive Shaft Washer (3, 6, 9 Ton) ............................. ...................................... 1
(includes 43A nut, 43B washer) ... M10 x 30 ....................... 5
26

17.0 Warranty and Service

JET warrants every product it sells against manufacturers’ defects. If one of our tools needs service or repair, please
contact Technical Service by calling 1-800-274-6846, 8AM to 5PM CST, Monday through Friday. Warranty Period
The general warranty lasts for the time period specified in the literature included with your product or on the official JET branded website.
JET products carry a limited warranty which varies in duration based upon the product. (See chart below)
Accessories carry a limited warranty of one year from the date of receipt.
Consumable items are defined as expendable parts or accessories expected to become inoperable within a
reasonable amount of use and are covered by a 90 day limited warranty against manufacturer’s defects.
Who is Covered
This warranty covers only the initial purchaser of the product from the date of delivery.
What is Covered
This warranty covers any defects in workmanship or materials subject to the limitations stated below. This warranty does not cover failures due directly or indirectly to misuse, abuse, negligence or accidents, normal wear-and-tear, improper repair, alterations or lack of maintenance. JET woodworking machinery is designed to be used with Wood. Use of these machines in the processing of metal, plastics, or other materials outside recommended guidelines may void the warranty. The exceptions are acrylics and other natural items that are made specifically for wood turning.
Warranty Limitations
Woodworking products with a Five Year Warranty that are used for commercial or industrial purposes default to a Two Year Warranty. Please contact Technical Service at 1-800-274-6846 for further clarification.
How to Get Technical Support Please contact Technical Service by calling 1-800-274-6846. Please note that you will be asked to provide proof of initial purchase when calling. If a product requires further inspection, the Technical Service representative will
explain and assist with any additional action needed. JET has Authorized Service Centers located throughout the United States. For the name of an Authorized Service Center in your area call 1-800-274-6846 or use the Service Center Locator on the JET website.
More Information
JET is constantly adding new products. For complete, up-to-date product information, check with your local distributor or visit the JET website.
How State Law Applies
This warranty gives you specific legal rights, subject to applicable state law.
Limitations on This Warranty
JET LIMITS ALL IMPLIED WARRANTIES TO THE PERIOD OF THE LIMITED WARRANTY FOR EACH PRODUCT. EXCEPT AS STATED HEREIN, ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE EXCLUDED. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
JET SHALL IN NO EVENT BE LIABLE FOR DEATH, INJURIES TO PERSONS OR PROPERTY, OR FOR INCIDENTAL, CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF OUR PRODUCTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
JET sells through distributors only. The specifications listed in JET printed materials and on official JET website are given as general information and are not binding. JET reserves the right to effect at any time, without prior notice, those alterations to parts, fittings, and accessory equipment which they may deem necessary for any reason whatsoever. JET
Product Listing with Warranty Period
90 Days – Parts; Consumable items 1 Year – Motors; Machine Accessories 2 Year – Metalworking Machinery; Electric Hoists, Electric Hoist Accessories; Woodworking Machinery used for industrial or commercial purposes 5 Year – Woodworking Machinery Limited Lifetime – JET Parallel clamps; VOLT Series Electric Hoists; Manual Hoists; Manual Hoist Accessories; Shop Tools; Warehouse & Dock products; Hand Tools; Air Tools
NOTE: JET is a division of JPW Industries, Inc. References in this document to JET also apply to JPW Industries, Inc., or any of its successors in interest to the JET brand.
®
branded products are not sold in Canada by JPW Industries, Inc.
27
427 New Sanford Road
LaVergne, Tennessee 37086
Phone: 800-274-6848
www.jettools.com
28
Loading...