Jenn-Air W103039888B Use & Care Manual

JENN-AIR_SIDEBYSIDEBUILT-INREFRIGERATOR

REFRIGERADOREMPOTRADO

DEDOSPUERTASJENN-AII_

RE NN-AIR_

For questions about features, operation/performance, parts, accessories, or service, call:

1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.com.

In Canada, call: 1-800-807-6777, or visit our website at www.jennair.ca.

MANUAL DEUSOY CUIDADO

Si tiene preguntas respecto alas caracteristicas, funcionamiento, rendimiento, partes, accesorios o servicio tecnico, Ilame al:

1-800-JENNAIR (1-800-536-6247) o visite nuestro sitio de internet: www.jennair.com.

En CanadA, Ilame al: 1-800-807-6777, o visite nuestro sitio de internet: www.jennair.ca.

GUIDED'UTILISATIONETD'ENTRETIEN

Au Canada, pour assistance, installation ou service, composez le 1-800-807-6777 ou visitez notre site web & www.jennair.ca.

Table of Contents/[ndice/Table des matieres ...................................................................................... 2

JENN-AIR °

W10303988B

USE& CAREGUIDE

TABLEOF CONTENTS

REFRIGERATOR SAFETY ............................................................. 3

Proper Disposal of Your Old Refrigerator .................................... 3

BEFORE USE .................................................................................. 4

Water Supply Requirements ........................................................ 4

Water System Preparation ........................................................... 4

REFRIGERATOR USE .................................................................... 5

Power On/Off Switch ................................................................... 5

Using the Controls ....................................................................... 6

Holiday Mode ............................................................................... 8

Ingredient Care Center ................................................................. 8

Water and Ice Dispensers ............................................................ 8

Ice Maker and Storage Bin ........................................................ 10

Water Filtration System .............................................................. 11

[NDICE

SEGURIDAD DEL REFRIGERADOR ........................................... 22

Como deshacerse adecuadamente de su refrigerador viejo....23

ANTES DE USAR .......................................................................... 23

Requisitos del suministro de agua ............................................. 23

Preparacion del sistema de agua .............................................. 24

USO DE SU REFRIGERADOR ..................................................... 25

Interruptor de encendido/apagado ............................................ 25

Uso de los controles .................................................................. 25

Holiday Mode (Modo de dia de fiesta) ....................................... 28

Ingredient Care Center (Centro de cuidado de ingredientes )..28

Despachadores de agua y hielo ................................................ 29

Fabrica de hielo y deposito ........................................................ 30

Sistema de filtracion de agua .................................................... 32

REFRIGERATOR CARE ............................................................... 12

Cleaning ...................................................................................... 12

Changing the Light Bulbs ........................................................... 13

Power Interruptions.................................................................... 13

Vacation Care ............................................................................. 13

TROUBLESHOOTING .................................................................. 14

Refrigerator Operation ................................................................ 14

Temperature and Moisture ......................................................... 15

Ice and Water ............................................................................. 15

ASSISTANCE OR SERVICE ......................................................... 16

ACCESSORIES ............................................................................. 17

WATER FILTER CERTIFICATIONS ............................................. 17

PERFORMANCE DATA SHEETS ................................................ 18

WARRANTY .................................................................................. 20

CUlDADO DE SU REFRIGERADOR ............................................ 33

Limpieza ..................................................................................... 33

Como cambiar los focos ............................................................ 33

Cortes de corriente ..................................................................... 34

Cuidado durante las vacaciones ................................................ 34

SOLUCION DE PROBLEMAS ...................................................... 35

Funcionamiento del refrigerador ................................................ 35

Temperatura y humedad ............................................................ 36

Hielo y agua ................................................................................ 36

AYUDA O SERVICIO TECNICO ................................................... 38

ACCESORIOS ............................................................................... 38

HOJA DE DATOS DEL RENDIMIENTO ...................................... 39

GARANTiA ..................................................................................... 41

TABLEDESMATIERES

SI_CURITI_ DU RI_FRIGI_RATEUR .............................................. 43

Mise au rebut appropriee de votre vieux refrig6rateur .............. 44

AVANT L'UTILISATION ................................................................ 44

Specifications de I'alimentation en eau ..................................... 44

Preparation du systeme d'eau ................................................... 45

UTILISATION DU RI_FRIGI_RATEUR .......................................... 46

Commutateur marche/arr_t ....................................................... 46

Utilisation des commandes ........................................................ 46

Holiday Mode (mode vacances) ................................................ 49

Ingredient Care Center (Centre de soins des ingredients) ........49

Distributeurs d'eau et de gla£;ons (sur certains modeles) ......... 50

Machine &gla£;ons et bac d'entreposage ................................. 51

Systeme de filtration d'eau ........................................................ 53

ENTRETIEN DU RI_FRIGI_RATEUR ............................................ 54

Nettoyage ................................................................................... 54

Remplacement des ampoules d'eclairage ................................ 54

Pannes de courant ..................................................................... 55

Entretien avant les vacances ..................................................... 55

DI_PANNAGE ................................................................................. 56

Fonctionnement du refrig6rateur ............................................... 56

Temperature et humidite ............................................................ 57

Gla£;ons et eau ........................................................................... 57

ASSISTANCE OU SERVICE ......................................................... 59

ACCESSOIRES ............................................................................. 59

FEUlLLES DE DONNEES SUR LA PERFORMANCE ................. 60

GARANTIE ..................................................................................... 62

2

REFRIGERATORSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow
instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury when using your refrigerator, follow these basic precautions:

• Plug into a grounded 3 prong outlet.

• Do not remove ground prong.

• Do not use an adapter.

• Do not use an extension cord.

• Disconnect power before servicing.

• Replace all parts and panels before operating.

• Remove doors from your old refrigerator.

SAVE THESE INSTRUCTIONS

• Use nonflammable cleaner.

• Keep flammable materials and vapors, such as gasoline,
away from refrigerator.

• Use two or more people to move and install refrigerator.

• Disconnect power before installing ice maker (on ice maker
kit ready models only).

• Use a sturdy glass when dispensing ice (on some models).

• Do not hit the refrigerator glass doors (on some models).

State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other
reproductive harm.

ProperDisposalofYourOld Refrigerator

Suffocation Hazard

Remove doors from your old refrigerator.
Failure to do so can result in death or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems
of the past. Junked or abandoned refrigerators are still
dangerous, even ifthey will sit for "just a few days." If you are
getting rid of your old refrigerator, please follow these instructions
to help prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

• Take off the doors.

• Leave the shelves in place so that children may not easily
climb inside.

important information to know about disposal of
refrigerants:

Dispose of refrigerator in accordance with Federal and Local
regulations. Refrigerants must be evacuated by a licensed,
EPA certified refrigerant technician in accordance with
established procedures.

BEFOREUSE

Remove the Packaging

• Remove tape and glue residue from surfaces before turning
on the refrigerator. Rub a small amount of liquid dish soap
over the adhesive with your fingers. Wipe with warm water
and dry.

• Do not use sharp instruments, rubbing alcohol, flammable
fluids, or abrasive cleaners to remove tape or glue. These
products can damage the surface of your refrigerator. For
more information, see "Refrigerator Safety."

• Dispose of/recycle all packaging materials.

Clean Before Using

If the water pressure to the reverse osmosis system is less than
40 psi (276 kPa):

• Check to see whether the sediment filter in the reverse
osmosis system is blocked. Replace the filter if necessary.

• Allow the storage tank on the reverse osmosis system to refill
after heavy usage.

• If your refrigerator has a water filter, it may further reduce the
water pressure when used in conjunction with a reverse
osmosis system. Remove the water filter. See "Water
Filtration System."

If you have questions about your water pressure, call a licensed,
qualified plumber.

After you remove all of the packaging materials, clean the inside
of your refrigerator before using it. See the cleaning instructions
in "Refrigerator Care."

Important information to know about glass shelves

and covers:

Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.
Tempered glass is designed to shatter into many small,
pebble-size pieces. This is normal. Glass shelves and covers
are heavy. Use both hands when removing them to avoid
dropping.

Read all directions before you begin.

IMPORTANT:

• When your refrigerator was installed, the water connection
from the water source should have been connected to your
refrigerator. Ifyour refrigerator is not connected to a water

source, see "Connect to Water Line" in the Installation
Instructions. If you have any questions about your water

connection, see "Troubleshooting" or call a licensed, qualified
plumber.

• If you turn the refrigerator on before the water line is
connected, turn the ice maker OFR See "Ice Maker and

Storage Bin."

• All installations must meet local plumbing code requirements.

Water Pressure

A cold water supply with water pressure between 30 and 120 psi
(207 and 827 kPa) is required to operate the water dispenser and
ice maker. If you have questions about your water pressure, see
"Troubleshooting" or call a licensed, qualified plumber.

Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the
refrigerator needs to be between 30 and 120 psi (207 and
827 kPa).

If a reverse osmosis water filtration system is connected to your
cold water supply, the water pressure to the reverse osmosis
system needs to be a minimum of 40 psi (276 kPa).

Please read before using the water system. Follow the directions
specific to your model.

Style 1 - Dispenser Models
IMPORTANT: After connecting the refrigerator to a water source

or replacing the water filter, follow the steps below to make sure
that the water system is properly cleaned. This will flush air from
the filter and water dispensing system, and prepare the water

filter for use.
The On/Off switch is located on the top right side of the freezer

compartment.

1. Open the freezer door and turn off the ice maker. Move the
switch to the OFF (right) setting as shown.

NOTE: Ifyour model has a base grille filter system, make sure the
base grille filter is properly installed and the cap is in the

horizontal position.

Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or
after the system.

2. Use a sturdy container to depress and hold the water
dispenser lever for 5 seconds, then release it for 5 seconds.

Repeat until water begins to flow. Once water begins to flow,
continue depressing and releasing the dispenser lever

(5 seconds on, 5 seconds off) until a total of 3 gal. (12 L)has
been dispensed. This will flush air from the filter and water

dispensing system, and prepare the water filter for use.
Additional flushing may be required in some households.

NOTE: As air is cleared from the system, water may spurt out
of the dispenser.

3. Open the freezer door and turn on the ice maker. Move the
switch to the ON (left) position.

• Allow 24 hours to produce the first batch of ice.

• Discard the first three batches of ice produced.

• Depending on your model, you may want to select the

maximum ice feature to increase the production of ice.

Style 2 - Non-Dispenser Models
IMPORTANT: After connecting the refrigerator to a water source

or replacing the water filter, fill and discard two full containers of
ice to prepare the water filter for use, before using the ice.

Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or
after the system.

1. Turn on the ice maker. Lower the wire shutoff arm as shown.

Please refer to "Ice Maker and Storage Bin" for further
instructions on the operation of your ice maker.

REFRIGERATORUSE

NOTES:

• Allow 24 hours to produce the first batch of ice.

• Allow 3 days to completely fill ice container.

• Depending on your model, you may want to select the

maximum ice feature to increase the production of ice.

NOTE: If your model has a base grille filter system, make sure the
base grille filter is properly installed and the cap is in the

horizontal position.

To Remove Top Grille:

1. Grasp both ends of the top grille.

2. Push the top grille straight up, then pull straight out. Lay the
grille on a soft surface.

B A B

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.
Do not use an adapter.

Do not use an extension cord.
Failure to follow these instructions can result in death,

fire, or electrical shock.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from refrigerator.
Failure to do so can result in death, explosion, or fire.

A. Top grille

B. Cabinet side trims

To Replace Top Grille:

1. Insert top grille hooks (located on the back of the top grille)
onto mounting bolts on the side trim.

2. Pull grille down slightly to lock into place.

Turn Power On or Off:

1. Remove top grille.

2. Press power switch to the On or Off position.

3. Replace top grille.

IMPORTANT: Be sure the power switch is set to the On position
after cleaning refrigerator or changing light bulbs.

/

/

If you need to turn the power to your refrigerator On or Off, you
must remove the top grille assembly to access the power switch.
Turn the power to the refrigerator Off when cleaning your
refrigerator or changing light bulbs.

A. Power switch

Depending on your model, your refrigerator may have Style 1 or Style1
Style 2 controls. Follow the instructions specific to your model.

IM PORTANT:

• Wait 24 hours after you turn on the refrigerator before you put
food into it. If you add food before the refrigerator has cooled
completely, your food may spoil.

NOTE: Adjusting the refrigerator and freezer controls to a
lower (colder) setting will not cool the compartments any

Style 2

faster.
If the temperature is too warm or too cold in the refrigerator or

freezer, first check the air vents to be sure they are not
blocked before adjusting the controls.

After the refrigerator is turned on, the Over Temperature audio
alarm and indicator light may activate every 1Y2hours until
the refrigerator and freezer temperatures are below 48°F (9°C)

CONDITION/REASON: TEMPERATURE

and 15°F (-9°C), respectively, or until the alarm is turned off.
To turn off the audio alarm and indicator light, see "Master

Alarm Reset."

REFRIGERATOR too cold REFRIGERATOR Control
Not set correctly for conditions 1° higher

Turning Refrigerator On/Off and Viewing Set Points

The On/Off touch pad on the control panel shuts down
refrigerator functions such as cooling, some lighting, fans and
compressors. To turn the power off completely, use the power
On/Off switch located behind the top grille. See "Power On/Off

Switch."

• Press and hold the ON/OFF touch pad for 3 seconds. The
LED will light up to indicate that cooling is Off. Press the

REFRIGERATOR too warm REFRIGERATOR Control
High use or room very warm

FREEZER too cold FREEZER Control
Not set correctly for conditions 1° higher

FREEZER too warm/too little ice FREEZER Control
High use or heavy ice use 1° lower

touch pad again to turn on cooling. The LED will turn off.

Alarm Functions

Viewing the Celsius Temperatures

Master Alarm Reset

• Press F/C touch pad. To redisplay degrees Fahrenheit, press
F/C again.

NOTE: If the freezer temperature is below zero, the negative
sign next to the freezer display will light up. This is normal.

Pressing Alarm Reset once will turn off the audio alarm and
indicator light. The audio alarm will not sound again for the

current condition that caused the alarm until a new condition
occurs or until a Master Alarm Reset is performed.

A Master Alarm Reset can be performed by pressing ON/OFF

Adjusting Controls

IM PORTANT:

• The preset settings should be correct for normal household
usage. The controls are set correctly when milk or juice is as
cold as you like and when ice cream is firm.

twice or by turning the power to the refrigerator off and on again.
See "Power On/Off Switch." After performing a Master Alarm
Reset, the indicator light will reactivate if the condition that
caused the alarm is still present. See "Over Temperature," "Call
Service," or "Door Alarm."

Style 1

NOTE: Wait at least 24 hours between adjustments. Recheck

the temperatures before other adjustments are made.

• Press the SET TO RECOMMENDED touch pad to reset the
set points to the factory recommended temperatures.

Style 2

NOTE: The factory recommended set points are 0°F (-18°C)
for the freezer and 37°F (2°C) for the refrigerator.

• The actual temperature may differ from the display when a
door is open for an extended period of time.

To Adjust Set Point Temperatures:

The set point range for the freezer is -5°F to 5°F (-21°C to -15°C).
The set point range for the refrigerator is 33°F to 45°F
(0°C to 7°C).

• Press the refrigerator or freezer PLUS (+) or MINUS (-) touch
pad until the desired temperature is reached.

Door Alarm
The Door Alarm indicator light will flash, an alarm will sound and

the interior lights will turn off when a door has been open for
longer than 10 minutes. When the door is closed, the audio alarm
will reset and turn off, but the Door Open indicator light will
continue to flash until the temperature is equal to or below 45°F
(7°C) and 15°F (-9°C) for the refrigerator and freezer
compartments, respectively.

NOTE: To deactivate the audio alarm and indicator light, see
"Master Alarm Reset."

OF -18_c

FROZEN FOOD

37=F 2=C

FRESH FOOD

ADJUSTMENT:

1° lower

Door Alarm •

Over Temp Alarm •

Call Service •

Door Alarm #_t

Over Temp Alarm _

6

Over Temperature
IMPORTANT: If the Over Temperature Alarm activates, your food

may spoil. See the "Power Interruptions." Minimize door
openings until temperatures return to normal.

The Over Temperature feature is designed to let you know when
either the refrigerator temperature rises above 48°F (9°C) or the
freezer temperature rises above 15°F (-9°C) for longer than
1V2hours. The audio alarm will shut off automatically when the
temperature returns to normal, but the indicator light will continue
to flash until the Alarm is pressed to let you know that an over
temperature condition has occurred.

If the over temperature condition is still present when an Over
Temperature Reset is performed, the indicator light will continue
to reactivate every 1V2hours until refrigerator and freezer
temperatures are below 48°F (9°C) and 15°F (-9°C), respectively.

NOTE: The audio alarm will be disabled for subsequent
occurrences of over temperature alarm condition. To enable the
audio alarm, see "Master Alarm Reset."

Call Service (on some models)
If the Call Service indicator light is flashing, call for service. See

the "Assistance or Service" section for information on calling for
service.

NOTE: The audio alarm will be disabled for subsequent
occurrences of the call service alarm condition. To enable the

audio alarm, see "Master Alarm Reset."

Max Cold

The Max Cold feature assists with periods of heavy ice usage, full
grocery loads, or temporarily warm room temperatures.

• Press MAX COLD to turn on the Max Cold feature. The Max
Cold indicator light will remain on for 24 hours unless

manually turned off.

NOTE: The temperature display will remain at 34°F (1°C) and -5°F
(-21 °C) for the refrigerator and freezer compartments,

respectively, while the Max Cool feature is enabled. After
24 hours, the refrigerator returns to the previous temperature set

points.

Sabbath Mode (on some models)

The Sabbath Mode feature is designed for the traveler or for
those whose religious observances require turning off the lights
and ice maker. By selecting this feature, the temperature set
points and Deli drawer settings remain unchanged, the ice maker
will be disabled and the interior lights will turn off. For most
efficient refrigerator operation, turn off Sabbath Mode when it is
no longer required.

• Press SABBATH MODE to turn on this feature.

• Press SABBATH MODE again to turn off this feature.

NOTES:

• If the refrigerator is operating in Sabbath mode and you press
SABBATH MODE to turn off the feature, close the doors to
reset the interior lighting.

• If the Max Cold feature has been selected prior to turning on
the Sabbath Mode feature, then the set points will remain at
34°F (1°C) and -5°F (-21 °C) for the refrigerator and freezer
compartments, respectively, until the Max Cold feature times
out. The refrigerator will then return to the previous
temperature set points chosen prior to the selection of the
Max Cold feature, but the lights and ice maker will remain off
until Sabbath Mode is pressed again.

Water Filter Status

Style 1-Reset

The Reset Filter control allows you to restart the water filter status
tracking feature each time you replace the water filter. See "Water
Filtration System."

• Press and hold RESET for 3 seconds, until the indicator
display changes to 99%.

% RemainLn 9

Rest Mode (on some models)

The Rest Mode feature is designed for the traveler or for those
whose religious observances require turning off the lights and ice

maker. By selecting this feature, the temperature set points and
Deli drawer settings remain unchanged, the ice maker will be

disabled and the interior lights will turn off. For most efficient
refrigerator operation, turn off Rest Mode when it is no longer

required.

• Press REST MODE to turn on this feature.

• Press REST MODE again to turn off this feature.

Rest Mode

NOTE: If the Max Cold feature has been selected prior to turning
on the Rest Mode feature, then the set points will remain at 34°F
(1°C) and -5°F (-21°C) for the refrigerator and freezer
compartments, respectively, until the Max Cold feature times out.
The refrigerator will then return to the previous temperature set
points chosen prior to the selection of the Max Cold feature, but
the lights and ice maker will remain off until Rest Mode is pressed
again.

WATER FILTER INDICATOR

Style 2-Reset Filter

The reset filter control allows you to restart the water filter status
tracking feature each time you replace you water filter. See
"Water Filtration System."

• Press and hold RESET FILTER for 3 seconds, until the Order
or Replace light turns off.

Water Filter Status

I_ Good

#_ Order Filter

#} Replace Filter

_O__"_i,_"_s_vW____,,,,A4_;_

TheHolidayModefeatureisdesignedforthetravelerorforthose
whosereligiousobservancesrequireturningoffthelightsandice
maker.Byselectingthisfeature,thetemperaturesetpointsand
Delldrawersettingsremainunchanged,theicemakerwillbe
disabledandtheinteriorlightswillturnoff.Formostefficient
refrigeratoroperation,turnoffHolidayModewhenitisnolonger
required.

Control Panel

In Holiday Mode, the temperature set points remain unchanged
and the interior lights turn off.

• Press Holiday Mode to turn on this feature.

Holiday Mode

• Press Holiday Mode again to turn off this feature.

The control for the Ingredient Care Center adjusts the
temperature of the storage drawer. Cold air flows into the drawer
through the air duct between the freezer and the refrigerator.
Adjusting the control allows more or less cold air through the air

duct.

Remove and Replace the Ingredient Care Center Cover

Important information to know about glass shelves

and covers:
Do not clean glass shelves or covers with warm water when

they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.
Tempered glass is designed to shatter into many small,
pebble-size pieces. This is normal. Glass shelves and covers
are heavy. Use both hands when removing them to avoid

dropping.

1=

Remove food from Ingredient Care Center cover. Pull drawer
out about 4" (10.16 cm). Reach under the glass shelf with
both hands and lift gently upward until back of shelf is free.
Tilt the shelf at an angle and remove the shelf from the
refrigerator. Do not bump the glass.

Adjust the Temperature

1. Choose a setting based on the item to be stored in the
drawer.

2. Push the button that corresponds to that setting.

3. The indicator light for that setting will illuminate to verify that
the drawer is ready to be loaded.

Style 1-Dispenser models

Various Cheeses

In_¢ed_ nt Care Cent et

Jams and Jellies _

Fresh Produce_ 0

Fresh Herbs 0Berry Fruits _

i Beverages_ Colder

Cold

Meats 9

Style 2-Non-dispenser Models

8

2. Replace the cover by holding the glass shelf firmly with both
hands, tilt the shelf at an angle and position it above the
support rails. Place shelf gently on support rails on side wall.

Meat Storage Guide

Store most meat in original wrapping as long as it is airtight and
moisture-proof. Rewrap if necessary. See the following chart for
storage times. When storing meat longer than the times given,

freeze the meat.

Fresh fish or shellfish ......................... use same day as purchased

Chicken, ground beef, variety meat (liver, etc.) ................ 1-2 days

Cold cuts, steaks/roasts .................................................. 3-5 days

Cured meats ................................................................... 7-10 days

Leftovers - Cover leftovers with plastic wrap, aluminum foil, or
plastic containers with tight lids.

IM PO RTANT:

• After connecting the refrigerator to a water source or
replacing the water filter, flush the water system. Use a sturdy
container to depress and hold the water dispenser lever for
5 seconds, then release it for 5 seconds. Repeat until water
begins to flow. Once water begins to flow, continue
depressing and releasing the dispenser lever (5 seconds on,
5 seconds off) until a total of 3 gal. (12 L) has been dispensed.
This will flush air from the filter and water dispensing system,
and prepare the water filter for use. Additional flushing may
be required in some households.

NOTE: As air iscleared from the system, water may spurt out
of the dispenser.

• Allow 24 hours for the refrigerator to cool down and chill
water.

• Allow 24 hours to produce the first batch of ice. Discard the
first three batches of ice produced.

• The dispensing system will not operate when the freezer door
is open.

Dependingonyourmodel,yourwaterandicedispensers
mayhaveoneormoreofthefollowingfeatures:awaterlevel
indicatorinthedispensertray,aspeciallightthatturnson
whenyouusethedispenser,oralockoptiontoavoid
unintentionaldispensing.

Water Dispenser

To Dispense Water:

1. Pressa sturdy glass against the water dispenser pad.

NOTES:

• While dispensing water and for 3 seconds after
dispensing has stopped, the digital display will show how

many ounces of water have been dispensed.
To switch from ounces to cups, press and hold ICE and

LOCK at the same time until the dispenser beeps after
3 seconds. To switch from cups to liters, press and hold

the buttons for another 3 seconds. To switch back to
ounces, repeat the process a third time.

2. Remove the glass to stop dispensing.
NOTE: Water may have an off-flavor if you do not use the

dispenser periodically. Dispense enough water every week to
maintain a fresh supply.

Ice Dispenser

Ice dispenses from the ice maker storage bin in the freezer when
the dispenser pad is pressed. The dispensing system will not
operate when the freezer door is open. To turn off the ice maker,
see "Ice Maker and Storage Bin."

Your ice maker can produce both crushed and cubed ice. The
display screen reads "CRUSHED" or "CUBED," indicating which
type is selected. To change the setting, press the ICE button
before dispensing ice.

For crushed ice, cubes are crushed before being dispensed. This
may cause a slight delay when dispensing crushed ice. Noise
from the ice crusher is normal, and pieces of ice may vary in size.
When changing from crushed to cubed, a few ounces of crushed
ice will be dispensed along with the first cubes.

To Dispense Ice:

1. Press the button to select the desired type of ice.

Cut Hazard

Use a sturdy glass when dispensing ice.
Failure to do so can result in cuts.

IMPORTANT: You do not need to apply a lot of pressure to

the pad in order to activate the ice dispenser. Pressing hard
will not make the ice dispense faster or in greater quantities.

3.

Remove the glass to stop dispensing.
NOTE: Ice may continue to dispense for up to 10 seconds

after removing the glass from the pad. The dispenser may
continue to make noise for a few seconds after dispensing.

Dispenser Traywith Water Level Indicator
(on some models)

Your dispenser may include a small tray at the bottom of the
dispenser. It is designed to catch small spills and allow for easy
cleaning. The tray can be removed from the dispenser and
carried to the sink to be emptied or cleaned.

NOTE: There is no drain in the tray. When the tray is full of water
and needs to be emptied, a small red indicator pops up at the
back of the tray.

Dispenser Light (on some models)

When you use the dispenser, the light will automatically turn on.
If you want the light to be on continuously, you may choose either

ON or AUTO.
ON: Press LIGHT to turn the dispenser light on.

AUTO: Press LIGHT a second time to select AUTO mode. The
dispenser light will automatically adjust to become brighter as the

room brightens, dimmer as the room darkens.
OFF: Press LIGHT a third time to turn the dispenser light off.
The dispenser lights are LEDs that cannot be changed. If it

appears that your dispenser lights are not working, be sure that
the light sensor is not blocked (in AUTO mode). See
"Troubleshooting" for more information.

Dispenser Lock (on some models)

The dispenser can be turned off for easy cleaning or to avoid
unintentional dispensing by small children and pets.

NOTE: The lock feature does not shut off power to the product,
to the ice maker, or to the dispenser light. It simply deactivates

the ice and water dispensers. To turn off the ice maker, see "Ice
Maker and Storage Bin."

• Press and hold LOCK for 3 seconds to lock the dispenser.
While the dispenser is locking, "LOCKING" will appear on the

display screen and the blue indicator light around the LOCK
button will flash. When the dispenser is locked, the indicator

light will change to red for a few seconds, then turn off.

• Press and hold LOCK a second time to unlock the dispenser.
While the dispenser is unlocking, "UNLOCKING" will appear

on the display screen and the red indicator light around the
LOCK button will flash. When the dispenser is unlocked, the

indicator light will change to blue for a few seconds, then turn
off.

2. Press a sturdy glass against the ice dispenser pad. Hold the
glass close to the dispenser opening so ice does not fall
outside of the glass.

WaterFilterStatus Light (on some models)

The water filter status light and display screen help you know
when to change your water filter. Press the FILTER button to
check the status of your water filter.

If the filter is new:
You must press FILTER to view the filter's status. For a few

seconds, the status light will be blue and the display screen will
show what percentage of your filter's life remains.

If it is almost time to change the filter:
The status light will automatically illuminate and will remain on,
appearing yellow. The words "ORDER FILTER" will appear on the
display screen. Press FILTER to see what percentage of your
filter's life remains. You should order the appropriate replacement

filter. See "Accessories."
If it is time to change the filter:

The status light will remain on, changing to red. The words
"REPLACE FILTER" and "HOLD BU-I-I-ON TO RESET" will appear
on the display screen until the filter has been changed and the
status light has been reset.

To reset the water filter status light:
After changing the filter, reset the status light by pressing and
holding the FILTER button for 3 seconds. The status light will
blink red and change to blue, then turn off when the system is

reset.

To Remove and Replace the Ice Bin:

1. Flip up the covering panel.

L____j

A. Ice maker cover

2. Lift the wire shutoff arm so it clicks into the OFF (up)
position. Ice can still be dispensed, but no more can be

made.

3. Lift up the front of the storage bin and pull the ice bin forward.

4. Replace the bin by pushing it in all the way or the dispenser
will not work. Push the wire shutoff arm down to the ON

position to restart ice production. Make sure the door is
closed tightly.

Style 2

IMPORTANT: Flush the water system before turning on the ice
maker. See "Water and Ice Dispensers." Allow 24 hours to
produce the first batch of ice. Discard the first three batches of
ice produced. Allow 3 days to completely fill the ice container.

Style I

To Turn the Ice Maker On/Off:

The On/Oft switch for the ice maker is a wire shutoff arm located
on the side of the ice maker.

1. To turn the ice maker on, simply lower the wire shutoff arm.
NOTE: Your ice maker has an automatic shutoff. As ice is

made, the ice cubes will fill the ice storage bin and the ice
cubes will raise the wire shutoff arm to the OFF (arm up)
position.

2. To manually turn the ice maker off, lift the wire shutoff arm to
the OFF (arm up) position and listen for the click to make sure
the ice maker will not continue to operate.

To Turn the Ice Maker On/Off:

The On/Off switch is located on the top right side of the freezer
compartment.

1. To turn the ice maker on, slide the control to the ON (left)
position.

NOTE: Your ice maker has an automatic shutoff. The ice
maker sensors will automatically stop ice production, but the

control will remain in the ON (left) position.

2. To manually turn the ice maker off, slide the control to the
OFF (right) position.

To Remove and Replace the Ice Storage Bin:

1. Hold the base of the storage bin with both hands and press
the release button to lift the storage bin up and out.

NOTE: It is not necessary to turn the ice maker control to the
OFF (right) position when removing the storage bin. The
sensor cover ("flipper door") on the left wall of the freezer
stops the ice maker from producing ice if the door is open or
the storage bin is removed.

2. Replace the storage bin on the door and push down to make
sure it is securely in place.

10

Clean the Ice Storage Bin

Water Filter Status Lights (non-dispenser models)

NOTE: It is normal for ice to stick together in the ice bin. Ice may
be dispensed or used more frequently which will break up the ice.
It is recommended that the ice container be emptied and cleaned

as needed.
To clean the ice storage bin:

1. Empty the ice container. Use warm water to melt the ice if
necessary.

NOTE: Do not use anything sharp to break up the ice in the
bin or bucket. This can cause damage to the ice container
and the dispenser mechanism.

2. Wash ice bin with a mild detergent, rinse well and dry
thoroughly. Do not use harsh or abrasive cleaners or solvents.

Remember

Allow 24 hours to produce the first batch of ice. Allow 3 days
to completely fill ice container.

Discard the first three batches of ice produced to avoid
impurities that may be flushed out of the system.

The quality of your ice will be only as good as the quality of
the water supplied to your ice maker.

Avoid connecting the ice maker to a softened water supply.
Water softener chemicals (such as salt) can damage parts of
the ice maker and lead to poor quality ice. If a softened water
supply cannot be avoided, make sure the water softener is
operating properly and is well maintained.

It is normal for the ice cubes to be attached at the corners.
They will break apart easily.

For Style 1 ice maker, do not force the wire shutoff arm up or
down.

Do not store anything on top of the ice maker or in the ice
storage bin/bucket.

The water filter status lights will remind you when it is time to
order and replace the water filter. When the Order Filter light is
on, it is almost time to change the water filter. When the Replace
Filter light is on, a new water filter should be installed.

The disposable water filter should be replaced at least every
6 months OR earlier if the flow of water to the ice maker

decreases noticeably.
After replacing the water filter, press and hold RESET FILTER for

3 seconds. The Good light will turn on when the filter tracking
feature is reset. See "Using the Controls."

Changing the Water Filter

The water filter is located in the base grille below the freezer
compartment door. It is not necessary to remove the base grille

to remove the filter.

1. Remove the filter by pressing the eject button and pulling
straight out on the filter cap.

NOTES:

Avoid twisting the cap when removing the filter because
this could cause the cap to come off. If this occurs,
replace the cap and pull the filter straight out.

• There will be water in the filter. Some spilling may occur.

A

A. Eject button
B. Filter cap

Depending on your model, there may be a water filter indicator or
water filter status lights on the control panel. Follow the
instructions specific to your model.

Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or
after the system.

Water Filter Indicator (dispenser models)

The water filter indicator, located on the control panel, will remind
you when it is time to order and replace the water filter.

A new water filter should display a reading of 99%. The reading in
the display will decrease as the filter life is used. A replacement
water filter should be ordered when "Order Filter" is displayed.
When "Change Filter" is displayed, a new water filter should be

installed.
The disposable water filter should be replaced every 6 months

OR earlier if the flow of water to the water dispenser or ice maker
decreases noticeably.

After changing the water filter, press and hold RESET for
2 seconds until the indicator display changes to 99%. See "Using

the Controls."

2. Remove the cap by turning it counterclockwise until it stops.
IMPORTANT: Do not discard the cap. It is part of your

refrigerator. Keep the cap to use with the replacement filter.

3. Align the ridge on the cap with the arrow on the new filter and
turn the cap until it snaps into place.

A. Cover
B. O-rings

4.

Remove the covers from the O-rings. Be sure the O-rings are
still in place after the covers are removed.

11

5. Place the cap (removed in Step 2) on the new filter. Align the
ridge on the cap with the arrow on the filter. Turn the cap
clockwise until it snaps into place.

REFRIGERATORCARE

Explosion Hazard

Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.

A. Eject button
B.Arrow on filter

C. Ridge on cap

6. Push the new filter into the opening in the base grille. As the
filter is inserted, the eject button will depress. The eject
button will pop back out when the filter is fully engaged.

7. Pull gently on the cap to check that the filter is securely in
place.

8. Flush the water system. See "Water and Ice Dispensers."

Using the Ice Maker Without a Water Filter

You can operate the ice maker without a water filter. Your ice will
not be filtered.

1. Remove the filter by pressing the eject button and pulling on
the cap. See "Changing the Water Filter" earlier in this

section.

2. Remove the cap by turning it counterclockwise until it stops.
IMPORTANT: Do not discard the cap. It is part of your

refrigerator. Keep the cap to use with the replacement filter.

3. With the cap in a horizontal position, insert the cap into the
base grille until it stops.

2>

4=

Turn the cap counterclockwise until the cap slips into the
attachment slot. Then, turn the cap clockwise until it is in a
horizontal position.

NOTE: The cap will not be even with the base grille.

Both the refrigerator and freezer sections defrost automatically.
However, clean both sections about once a month to avoid build-

up of odors. Wipe up spills immediately.
To Clean Your Refrigerator:

1. Remove the top grille. See "Power On/Off Switch."

2. Press power switch to OFE

3. Remove all removable parts from inside, such as shelves,
crispers, etc.

4. Hand wash, rinse, and dry removable parts and interior
surfaces thoroughly. Use a clean sponge or soft cloth and a
mild detergent in warm water.

• Do not use abrasive or harsh cleaners such as window

sprays, scouring cleansers, flammable fluids, cleaning
waxes, concentrated detergents, bleaches or cleansers
containing petroleum products on plastic parts, interior
and door liners or gaskets. Do not use paper towels,
scouring pads, or other harsh cleaning tools. These can
scratch or damage materials.

• To help remove odors, you can wash interior walls with a

mixture of warm water and baking soda (2 tbs to 1 qt

[26 g to 0.95 L] of water).

5. Wash stainless steel and painted metal exteriors with a clean
sponge or soft cloth and a mild detergent in warm water. Do
not use abrasive or harsh cleaners, or cleaners containing
chlorine. Dry thoroughly with a soft cloth.

NOTE: To keep your Stainless Steel refrigerator looking like
new and to remove minor scuffs or marks, it is suggested that
you use the manufacturer's approved Stainless Steel Cleaner

and Polish.
IMPORTANT: This cleaner is for Stainless Steel parts only!

Do not allow the Stainless Steel Cleaner and Polish to come
into contact with any plastic parts such as the trim pieces,

dispenser covers or door gaskets. If unintentional contact
does occur, clean plastic part with a sponge and mild
detergent in warm water. Dry thoroughly with a soft cloth. To

order the cleaner, see "Accessories."

6.

Clean the condenser coils located behind the top grille
ventilation panel regularly. Coils may need to be cleaned as
often as every other month. This may help save energy.

• Use a vacuum cleaner with an extended attachment to

clean the condenser coils when they are dusty or dirty.

7=

Press the power switch to ON.

8.

Replace the top grille. See "Power On/Off Switch."

12

NOTE: Not all appliance bulbs will fit your refrigerator. Be sure to
replace the bulb with one of the same size and shape. All lights
require a @-watt maximum appliance bulb. Replacement bulbs
are available from your dealer or appliance store.

1. Remove the top grille. See "Power On/Off Switch."

2. Press the power switch to OFF.

3. Remove light shield when applicable as shown.
NOTE: To clean a light shield, wash it with warm water and a

liquid detergent. Rinse and dry the shield well.

4. Remove light bulb and replace with one of the same size,
shape and wattage.

5. Replace light shield when applicable as shown.

6. Press the power switch ON.

7. Replace the top grille. See "Power On/Off Switch."

Refrigerator Control Panel Lights

There are two or three light bulbs located inthe top front of the
refrigerator compartment behind a light shield.

• Open the light shield. Grasp the light shield by the openings.
Gently push back and pull down, as shown, to access the
light bulbs.

A. Light shield

• Remove the light bulb and replace it with one of the same
size, shape and wattage.

• Close the light shield by raising it up into place.
NOTE: If needed, clean the light shield with a damp soft

cloth.

Freezer and Crisper Lights

Remove the light shield by grasping the sides and squeezing
in toward the center. Once the side hooks of the shield are

free from the freezer or crisper lining, pull down the shield.
Replace the light shield by squeezing the top and bottom

toward the center and inserting the hooks into the slotted
holes. Once the hooks are in place, snap the front tab into the
slotted hole.

If the power will be out for 24 hours or less, keep the door or
doors closed (depending on your model) to help food stay cold

and frozen.
If the power will be out for more than 24 hours, do one of the

following:

• Remove all frozen food and store it in a frozen food locker.

• Place 2 Ibs (907 g) of dry ice in the freezer for every cubic foot
(28 L) of freezer space. This will keep the food frozen for 2 to
4 days.

• If neither a food locker nor dry ice is available, consume or
can perishable food at once.

REMEMBER: A full freezer stays cold longer than a partially filled
one. A freezer full of meat stays cold longer than a freezer full of
baked goods. If you see that food contains ice crystals, it may be
refrozen, although the quality and flavor may be affected. If the
condition of the food is poor, dispose of it.

Your refrigerator is equipped with the Holiday Mode feature,
which is designed for the traveler who wishes to turn off the lights

and ice maker. By selecting this feature, the temperature set
points remain unchanged, the ice maker will be disabled and the

interior lights will turn off. For most efficient refrigerator operation,
it is recommended to exit Holiday Mode when it is no longer

required.

If You Choose To Leave the Refrigerator On While You're
Away:

1. Use up any perishables and freeze other items.

2. Press HOLIDAY.

3. If your refrigerator has an automatic ice maker, shut off water
supply to the ice maker.

4. Empty the ice bin.

5. When you return from vacation, press HOLIDAY to return to
normal operation.

If You Choose To Turn the Refrigerator Off Before You
Leave:

1. Remove all food from the refrigerator.

2. If your refrigerator has an automatic ice maker:

• Turn off the water supply to the ice maker at least one day

ahead of time.

• When the last load of ice drops, raise the wire shutoff arm

to the OFF (up) position.

3.

Depending on your model, turn the Thermostat Control
(or Refrigerator Control) to OFF. See "Using the Controls."

4.

Clean refrigerator, wipe it, and dry well.

5.

Tape rubber or wood blocks to the tops of both doors to prop
them open far enough for air to get in. This stops odor and
mold from building up.

13

TROUBLESHOOTING

Try the solutions suggested here first in order to avoid the cost of an unnecessary service call.

The refrigerator will not operate

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.

Do not use an extension cord.
Failure to follow these instructions can result in death,

fire, or electrical shock.

Power cord unplugged? Plug into a grounded 3 prong
outlet.

Is outlet working? Plug in a lamp to see if the outlet is
working.

Household fuse blown or circuit breaker tripped? Replace
the fuse or reset the circuit breaker. If the problem continues,

call an electrician.

• Are controls on? Make sure the refrigerator controls are on.
See "Using the Controls."

• Is refrigerator defrosting? Your refrigerator will regularly run
an automatic defrost cycle. Recheck in 30 minutes to see if it
is operating.

• New installation? Allow 24 hours following installation for
the refrigerator to cool completely.

NOTE: Adjusting the temperature controls to coldest setting
will not cool either compartment more quickly.

The refrigerator is noisy

Refrigerator noise has been reduced over the years. Due to this
reduction, you may hear intermittent noises from your new
refrigerator that you did not notice from your old model. Below
are listed some normal sounds with an explanation.

• Buzzing - heard when the water valve opens to fill the ice
maker

• Pulsating - fans/compressor adjusting to optimize
performance

• Rattling - flow of refrigerant, water line, or from items placed
on top of the refrigerator

• Sizzling/Gurgling - water dripping on the heater during
defrost cycle

• Popping - contraction/expansion of inside walls, especially
during initial cool-down

• Water running - may be heard when water melts during the
defrost cycle and runs into the drain pan

• Creaking/Cracking - occurs as ice is being ejected from the
ice maker mold.

There is no audible door open alarm

Has the door been open less than 10 minutes? The door open

alarm will only flash when the door has been open for 10 minutes.
The audible alarm will sound the first time the door is left open for
more than 10 minutes. Subsequent door open alarms will only
flash. You must reset the audible alarm each time. See "Using the
Control(s)."

The doors will not close completely

• Door blocked open? Move food packages away from door.

• Bin or shelf in the way? Push bin or shelf back in the correct
position.

The doors are difficult to open

The motor seems to run too much

Your new refrigerator may run longer than your old one due to its
high-efficiency compressor and fans. The unit may run even
longer if the room is warm, a large food load is added, doors are
opened often, or if the doors have been left open.

14

Explosion Hazard

Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.

• Are the gaskets dirty or sticky? Clean gaskets with mild
soap and warm water.

The lights do not work

The ice cubes are hollow or small

• Is a light bulb loose in the socket or burned out? See
"Changing the Light Bulbs."

• Is the refrigerator in Sabbath Mode or Rest Mode? See
"Using the Controls."

• Has the door been open more than 10 minutes? See
"Using the Controls."

Temperature is too warm

• New installation? Allow 24 hours following installation for
the refrigerator to cool completely.

• Door(s) opened often or left open? Allows warm air to enter
refrigerator. Minimize door openings and keep doors fully

closed.

• Large load of food added? Allow several hours for
refrigerator to return to normal temperature.

• Controls set correctly for the surrounding conditions?
Adjust the controls a setting colder. Check temperature in
24 hours. See "Using the Controls."

• Refrigerator not cooling? For models with digital controls,
turn the refrigerator OFF and then ON to reset. Ifthis does not
correct the problem, call for service.

• Air vents blocked? Remove any item from in front of the air
vents.

There is interior moisture buildup

NOTE: Some moisture buildup is normal.

• Humid room? Contributes to moisture buildup.

• Door(s) opened often or left open? Allows humid air to
enter refrigerator. Minimize door openings and keep doors
fully closed.

NOTE: This is an indication of low water pressure.

• Water shutoff valve not fully open? Turn the water shutoff
valve fully open.

• Kink in the water source line? A kink in the line can reduce
water flow. Straighten the water source line.

• Reverse osmosis water filtration system connected to
your cold water supply? This can decrease water pressure.
See "Water Supply Requirements."

• Questions remain regarding water pressure? Call a
licensed, qualified plumber.

Ice is sticking together in the ice storage bin

• It is normal for frost to be on top of the ice storage bin due to
normal opening and closing of the freezer.

• It is normal for ice to stick together when it is not dispensed
or used frequently. It is recommended that the ice storage bin
be emptied and cleaned as needed. See "Ice Maker and
Storage Bin."

Off-taste, odor or gray color in the ice

New plumbing connections? New plumbing connections

can cause discolored or off-flavored ice.
Ice stored too long? Discard ice. Wash ice bin. Allow

24 hours for ice maker to make new ice.
Odor transfer from food? Use airtight, moisture proof

packaging to store food.
Are there minerals (such as sulfur) in the water? A water

filter may need to be installed to remove the minerals.
Is there a water filter installed on the refrigerator? Gray or

dark discoloration in ice indicates that the water filtration
system needs additional flushing.

The ice dispenser will not operate properly

%/21 I%_ WW%uIl%?l

The ice maker is not producing ice or not enough ice

• Refrigerator connected to a water supply and the supply
shutoff valve turned on? Connect refrigerator to water

supply and turn water shutoff valve fully open.

• Kink in the water source line? A kink in the line can reduce
water flow. Straighten the water source line.

• Ice maker turned on? Make sure wire shutoff arm or switch
(depending on model) is in the ON position.

• New installation? Wait 24 hours after ice maker installation
for ice production to begin. Wait 72 hours for full ice

production.

• Large amount of ice recently removed? Allow 24 hours for
ice maker to produce more ice.

• Ice cube jammed in the ice maker ejector arm?
Remove ice from the ejector arm with a plastic utensil.

• Reverse osmosis water filtration system connected to
your cold water supply? This can decrease water pressure.
See "Water Supply Requirements" in either the Installation

Instruction booklet or the Use & Care Guide.

• Freezer door closed completely? Close the door firmly. If it
does not close completely, see "The doors will not close
completely."

• Ice bin installed correctly? Be sure the ice bin is firmly in
position.

• New installation? Wait 24 hours after ice maker installation
for ice production to begin. Wait 72 hours for full ice

production.

• Ice stuck in the delivery chute? Use a plastic utensil to clear
the delivery chute.

• Has the wrong ice been added to the bin? Use only cubes
produced by the current ice maker.

• Has the ice melted around the auger (metal spiral) in the
ice bin? Empty the ice container. Use warm water to melt the
ice if necessary.

15

Cut Hazard

Use a sturdy glass when dispensing ice.
Failure to do so can result in cuts.

• Is the ice dispenser stalling while dispensing "crushed"
ice? Change the ice button from "crushed" to "cubed." If

cubed ice dispenses correctly, depress the button for
"crushed" ice and begin dispensing again.

• Has the dispenser arm been held in too long? Ice will stop
dispensing when the arm is held in too long. Wait 3 minutes
for dispenser motor to reset before using again.

The water dispenser will not operate properly

• Freezer door closed completely? Close the door firmly. If it
does not close completely, see "The doors will not close
completely."

• Refrigerator connected to a water supply and the supply
shutoff valve turned on? Connect refrigerator to water
supply and turn water shutoff valve fully open.

• Is the water pressure at least 30 psi (207 kPa)? The water
pressure to the home determines the flow from the dispenser.
See "Water Supply Requirements."

Kink in the home water source line? Straighten the water
source line.

New installation? Flush and fill the water system.
Water filter installed on the refrigerator? The filter may be

clogged or incorrectly installed.
Is a reverse osmosis water filtration system connected to

your cold water supply? See "Water Supply Requirements"
in either the Installation Instructions or the Use & Care Guide.

Water is leaking from the dispenser

NOTE: One or two drops of water after dispensing is normal.

• Glass not being held under the dispenser long enough?
Hold the glass under the dispenser 2 to 3 seconds after
releasing the dispenser lever.

• New installation? Flush the water system. See "Prepare the
Water System" or "Water and Ice Dispensers."

• Recently changed water filter? Flush the water system. See
"Prepare the Water System" or "Water and Ice Dispensers."

The dispenser water is not cool enough

NOTE: Water from the dispenser is chilled to only 50°F (10°C).

• New installation? Allow 24 hours after installation for the
water supply to cool completely.

• Recently dispensed large amount of water? Allow
24 hours for water supply to cool completely.

• Water not been recently dispensed? The first glass of water
may not be cool. Discard the first glass of water.

• Refrigerator connected to a cold water pipe? Make sure
the refrigerator is connected to a cold water pipe. See "Water
Supply Requirements."

ASSISTANCEORSERVICE

If you need assistance or service, first see the "Troubleshooting"
section. Additional help is available. Call us at 1-800-JENNAIR
(1-800-536-6247} from anywhere in the U.S.A., or write:

Jenn-Air Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Information may also be obtained by visiting our website at

www.jennair.com.

In Canada, for assistance, installation or service, call us at
1-800-807-6777, or write:

Jenn-Air Brand Home Appliances

Customer eXperience Centre

200 - 6750 Century Ave.

Mississauga, Ontario L5N 0B7
In Canada, visit www.jennair.ca.
Please include a daytime phone number in your correspondence.
Keep this book and your sales slip together for future

reference. You must provide proof of purchase or installation
date for in-warranty service.

Write down the following information about your appliance to help
you obtain assistance or service if you ever need it. You will need
to know your complete model number and serial number. You can
find this information on the model and serial number label, located
on the inside wall of the refrigerator compartment.

Dealer name

Serial number

Address

Phone number

Model number

Purchase date

16

ACCESSORIES

To order stainless steel cleaner or replacement filters, call
1-800-688-1100 and ask for the part number listed below or
contact your authorized Jenn-Air dealer. In Canada, call

1-800-807-6777.

WATERFILTERCERTIFICATIONS

State of California

Department of Health Services

Water Treatment Device

Certificate Number

05 - 1703

Da_e Issued: Aprd6,2lJ05

Date Revised: September 7, 2005

Trademark/Model Designation

Ki_cbenAi{

Manufactureri

116830 ofthe

Stainless Steel Cleaner and Polish:
Order Part #4396095

Replacement Water Filter:
Order Part #4396841 (T2RFWG2)

State of California

Department of Heallh Services

Water TreaUnent Device

Cerlificale Number

05- 1702

Date Issued: April 6, 2005

Date Rcvtsed- Scp/embcr 7, 2005

l'radelnark]Modet Designation

Whirlpool Deluxe T1WG2

WhMpoot DeluxeT1WG2L

Rel_lacemertt Elements

Rated Service Capacity: 200 gats Rated Service Flow: 085 gpm

Du not u_e with water fl_a| is microNologically unsafe or of unknown quality, withum adequate dislnlection belbee or
after the system

Conditions of Certification:

RatedServiceCapacity: 200gals RatedServlceFIow: 05gpm

Do not use with wa_er that is microbiok_gically unsalE or of unknown quali_y, without adequate disinfection before or

after the system

Conditions of Certification:

17

PERFORMANCEDATASHEETS

Base Grille Water Filtration System

Model T2WG2L/T2RFWG2 Capacity 200 Gallons (757 Liters)

Model T2WG2/T2RFWG2 Capacity 200 Gallons (757 Liters)

System tested and certified by NSF International against NSF/ANSI
Standard 42 for the reduction of Chlorine Taste and Odor, Particulate

Class I1"; and against NSF/ANSI Standard 53 for the reduction of Mercury,

Benzene, Toxaphene, O-dichlorobenzene, and Carbofuran.

This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The
concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the

permissible limit for water leaving the system, as specified in NSF/ANSI Standards 42 and 53.

Substance Reduction NSF Reduction Average Influent Challenge Maximum Average Minimum % Average %

Aesthetic Effects Requirements Influent Concentration Effluent Effluent Reduction Reduction

Chlorine Taste/Odor 50% reduction 2.0182 mg/L 2.0 mg/L + 10% 0.06 mg/L ** 0.0536 mg/L 97.03 97.34
Particulate Class I1" 85% reduction 1333333 #/mL At east 10,000 part c es/mL 6600 #/mL 2325 #/mL 99.51 99.83

Contaminant NSF Reduction Average Influent Challenge Maximum Average Minimum % Average %
Reduction Requirements Influent Concentration Effluent Effluent Reduction Reduction

Lead: @pH 6.5*** 0.010 mg/L 0.1533 mg/L 0.15 mg/L + 10% 0.0005 mg/L 0.0005 mg/L 99.67 99.67
Lead: @pH 8.5*** 0.010 mg/L 0.1400 mg/L 0.15 mg/L _+10% 0.0007 mg/L 0.0006 mg/L 99.50 99.57

Mercury: @ pH 6.5 0.002 mg/L 0.0058 mg/L 0.006 mg/L + 10% 0.0002 mg/L 0.0002 mg/L 96.54 96.54
Mercury: @ pH 8.5 0.002 mg/L 0.0059 mg/L 0.006 mg/L _+10% 0.0005 mg/L 0.0003 mg/L 91.57 94.92

Benzene 0.005 mg/L 0.0154 mg/L 0.015 mg/L _+10% 0.0012 mg/L 0.0006 mg/L 92.22 96.34
O-Dichlorobenzene 0.6 mg/L 1.7571 mg/L 1.8 mg/L _+10% 0.0250 mg/L 0.0066 mg/L 98.58 99.63

Toxaphene 0.003 mg/L 0.015 mg/L 0.015 mg/L _+10% 0.001 mg/L 0.001 mg/L 93.33 93.33

Carbofuran 0.04 mg/L 0.0819 mg/L 0.08 mg/L _+10% 0.0400 mg/L 0.0213 mg/L 51.13 74.00

Test Parameters: pH = 7.5 _+0.5 unless otherwise noted. Flow = 0.85 gpm (3.2 Lpm). Pressure = 60 psig (413.7 kPa).
Temp. = 68°F to 71.6°F (20°C to 22°C). Rated service capacity = 200 gallons (757 liters).

• It is essential that operational, maintenance, and filter
replacement requirements be carried out for the product to

perform as advertised.

• Use replacement filter T2RFWG2, part #4396841.
2011 suggested retail price of $39.99 U.S.A./S54.95 Canada.

Prices are subject to change without notice.
Model T2WG2L: Style 1 - When the filter indicator reads 10%,

order a new filter. When the indicator reads 0%, it is
recommended that you replace the filter.

Style 2 - When the filter indicator changes from green to yellow,
order a new filter. When the indicator changes from yellow to red,

it is recommended that you replace the filter.
Style 3 - When the water filter status display changes from

"GOOD" to "ORDER," order a new filter. When the filter indicator
reads "REPLACE," it is recommended that you replace the filter.

Style 4 - Press FILTER to check the status of your water filter. If
the filter indicator light is yellow, order a new filter. If the filter
indicator light is red, it is recommended that you replace the filter.

Model T2WG2: Change the water filter cartridge every 6 months.
If the water flow to the water dispenser or ice maker decreases

noticeably before 6 months have passed, replace the water filter
cartridge more often.

• These contaminants are not necessarily in your water supply.
While testing was performed under standard laboratory

conditions, actual performance may vary.

• The product is for cold water use only.

• Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after the
system.

• Refer to the "Warranty" section for the Manufacturer's name,
address and telephone number.

• Refer to the "Warranty" section for the Manufacturer's limited
warranty.

Application Guidelines/Water Supply Parameters

Water Supply City or Well
Water Pressure 30 - 120 psi (207 - 827 kPa)
Water Temperature 33° - 100°F (0.6° - 37.8°C)
Service Flow Rate 0.85 gpm (3.2 Lpm) @ 60 psi

*Class II particle size: 1 um to <5 um

**Test requirement is at least 100,000 particles/mL of AC Fine Test Dust.

***Compliant for Lead reduction requirements under NSF/ANSl Standard 53 as tested by Pace Analytical Services, Inc.

® NSF is a registered trademark of NSF International.

18

Base Grille Water Filtration System

Model TIWG2L/T2RFWG2 Capacity 200 Gallons (757 Liters)

Model TIWG2/T2RFWG2 Capacity 200 Gallons (757 Liters)

System tested and certified by NSF International against NSF/ANSI
Standard 42 for the reduction of Chlorine Taste and Odor, Particulate
Class I1"; and against NSF/ANSI Standard 53 for the reduction of Mercury,

Benzene, Toxaphene, O-dichlorobenzene, and Carbofuran.

This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The
concentration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the
permissible limit for water leaving the system, as specified in NSF/ANSI Standards 42 and 53.

Substance Reduction NSF Reduction Average Influent Challenge Maximum Average Minimum % Average %

Aesthetic Effects Requirements Influent Concentration Effluent Effluent Reduction Reduction

Chlorine Taste/Odor 50% reduction 2.0182 mg/L 2.0 mg/L + 10% 0.06 mg/L ** 0.0536 mg/L 97.03 97.34
Particulate Class I1" 85% reduction 1333333 #/mL At east 10,000 part c es/mL 6600 #/mL 2325 #/mL 99.51 99.83
Contaminant NSF Reduction Average Influent Challenge Maximum Average Minimum % Average %

Reduction Requirements Influent Concentration Effluent Effluent Reduction Reduction
Lead: @pH 6.5*** 0.010 mg/L 0.1533 mg/L 0.15 mg/L + 10% 0.0005 mg/L 0.0005 mg/L 99.67 99.67
Lead: @pH 8.5*** 0.010 mg/L 0.1400 mg/L 0.15 mg/L _+10% 0.0007 mg/L 0.0006 mg/L 99.50 99.57
Mercury: @ pH 6.5 0.002 mg/L 0.0058 mg/L 0.006 mg/L + 10% 0.0002 mg/L 0.0002 mg/L 96.54 96.54
Mercury: @ pH 8.5 0.002 mg/L 0.0059 mg/L 0.006 mg/L _+10% 0.0005 mg/L 0.0003 mg/L 91.57 94.92
Benzene 0.005 mg/L 0.0154 mg/L 0.015 mg/L _+10% 0.0012 mg/L 0.0006 mg/L 92.22 96.34

O-Dichlorobenzene 0.6 mg/L 1.7571 mg/L 1.8 mg/L _+10% 0.0250 mg/L 0.0066 mg/L 98.58 99.63

Toxaphene 0.003 mg/L 0.015 mg/L 0.015 mg/L _+10% 0.001 mg/L 0.001 mg/L 93.33 93.33

Carbofuran 0.04 mg/L 0.0819 mg/L 0.08 mg/L _+10% 0.0400 mg/L 0.0213 mg/L 51.13 74.00

Test Parameters: pH = 7.5 _+0.5 unless otherwise noted. Flow = 0.5 gpm (1.9 Lpm). Pressure = 60 psig (413.7 kPa).
Temp. = 68°F to 71.6°F (2O°C to 22°C). Rated service capacity = 200 gallons (757 liters).

• It is essential that operational, maintenance, and filter
replacement requirements be carried out for the product to

perform as advertised.

• Use replacement filter T2RFWG2, part #4396841.
2011 suggested retail price of $39.99 U.S.A./S54.95 Canada.
Prices are subject to change without notice.

Model TlWG2L: Style 1 - When the filter indicator reads 10%,
order a new filter. When the indicator reads 0%, it is

recommended that you replace the filter.
Style 2 - When the filter indicator changes from green to yellow,

order a new filter. When the indicator changes from yellow to red,
it is recommended that you replace the filter.

Style 3 - When the water filter status display changes from
"GOOD" to "ORDER," order a new filter. When the filter indicator

reads "REPLACE," it is recommended that you replace the filter.
Style 4 - Press FILTER to check the status of your water filter. If

the filter indicator light is yellow, order a new filter. If the filter
indicator light is red, it is recommended that you replace the filter.

Model TlWG2: Change the water filter cartridge every 6 months.
If the water flow to the water dispenser or ice maker decreases

noticeably before 6 months have passed, replace the water filter
cartridge more often.

• These contaminants are not necessarily in your water supply.
While testing was performed under standard laboratory

conditions, actual performance may vary.

• The product is for cold water use only.

• Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after the

system.

• Refer to the "Warranty" section for the Manufacturer's name,
address and telephone number.

• Refer to the "Warranty" section for the Manufacturer's limited
warranty.

Application Guidelines/Water Supply Parameters

Water Supply City or Well
Water Pressure 30 - 120 psi (207 - 827 kPa)
Water Temperature 33° - 100°F (0.6° - 37.8°C)
Service Flow Rate 0.5 gpm (1.9 Lpm) @ 60 psi

*Class II particle size: 1 um to <5 um

**Test requirement is at least 100,000 particles/mL of AC Fine Test Dust.

***Compliant for Lead reduction requirements under NSF/ANSl Standard 53 as tested by Pace Analytical Services, Inc.

® NSF is a registered trademark of NSF International.

19

JENN-AII BUILT-INREFRIGERATORWARRANTY

TWO YEAR LIMITED WARRANTY

For two years from the date of purchase, when this major appliance is installed, operated and maintained according to instructions attached
to or furnished with the product, Jenn-Air brand of Whirlpool Corporation or Whirlpool Canada LP (hereafter "Jenn-Air") will pay for factory
specified replacement parts and repair labor to correct defects in materials or workmanship that existed when this major appliance was
purchased.

THIRD THROUGH SIXTH YEAR LIMITED WARRANTY ON SEALED REFRIGERATION SYSTEM

In the third through sixth years from the date of purchase, when this major appliance is installed, operated and maintained according to
instructions attached to or furnished with the product, Jenn-Air will pay for factory specified replacement parts and repair labor for the

following components to correct defects in materials or workmanship in the sealed refrigeration system that existed when this major
appliance was purchased: compressor, evaporator, condenser, dryer, and connecting tubing.

SEVENTH THROUGH TWELFTH YEAR LIMITED WARRANTY (SEALED REFRIGERATION SYSTEM ONLY - LABOR NOT INCLUDED)

In the seventh through twelfth year from the date of purchase, when this major appliance is installed, operated and maintained according to
instructions attached to or furnished with the product, Jenn-Air will pay for factory specified replacement parts for the following components

to correct defects in materials or workmanship in the sealed refrigeration system that existed when this major appliance was purchased:
compressor, evaporator, condenser, dryer, and connecting tubing.

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. Service
must be provided by a Jenn-Air designated service company. This limited warranty is valid in the United States or Canada and applies only

when the major appliance is used in the country in which it was purchased. This limited warranty is effective from the date of the original
consumer purchase. Proof of original purchase date is required to obtain service under this limited warranty.

On models with a water filter: 30 day limited warranty on water filter. For 30 days from the date of purchase, when this filter is operated and
maintained according to instructions attached to or furnished with the product, Jenn-Air will pay for a replacement water filter to correct

defects in materials and workmanship.

ITEMS EXCLUDED FROM WARRANTY

This limited warranty does not cover:

1. Replacement parts or repair labor if this major appliance is used for other than normal, single-family household use or when it is used in a
manner that is inconsistent to published user or operator instructions and/or installation instructions.

2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or repair
house fuses, or to correct house wiring or plumbing.

3. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty coverage.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in accordance
with electrical or plumbing codes, or use of products not approved by Jenn-Air.

5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage results
from defects in materials or workmanship and is reported to Jenn-Air within 30 days from the date of purchase.

6. Any food or medicine loss due to refrigerator or freezer product failures.

7. Pickup and delivery. This major appliance is intended to be repaired in your home.

8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.

9. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an
authorized Jenn-Air servicer is not available.

10. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance with
Jenn-Air's published installation instructions.

11. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered or cannot be
easily determined.

12. Removal or replacement of trim, decorative panels, flooring, cabinetry, islands, countertops, drywall or other built-in fixtures that interfere
with servicing, removal or replacement of the product.

The cost of repair or replacement under these excluded circumstances shall be borne by the customer.

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not
allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This warranty gives

you specific legal rights, and you also may have other rights that vaw from state to state or province to province.

DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY

Jenn-Air makes no representations about the quality, durability, or need for service or repair of this major appliance other than the
representations contained in this Warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes with
this major appliance, you should ask Jenn-Air or your retailer about buying an extended warranty.

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. JENN-
AIR SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the exclusion or

limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you specific
legal rights, and you also may have other rights that vary from state to state or province to province.

If outside the 50 United States and Canada, contact your authorized Jenn-Air dealer to determine if another warranty applies.
If you think you need repair service, first see the "Troubleshooting" section of the Use & Care Guide. If you are unable to resolve the problem

after checking "Troubleshooting," additional help can be found by checking the "Assistance or Service" section or by calling Jenn-Air. In the
U.S.A., call 1-800-536-6247. In Canada, call 1-800-807-6777. 6/12

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

20