Jenn-Air W10297654A Installation Manual

JENN-AIR® BOTTOM MOUNT BUILT-IN REFRIGERATOR

REFRIGERADOR EMPOTRADO CON

CONGELADOR EN LA PARTE INFERIOR JENN-AIR

RÉFRIGÉRATEUR ENCASTRÉ AVEC CONGÉLATEUR

EN BAS JENN-AIR

For questions about features, operation/performance, parts, accessories, or service, call:

1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.com.

In Canada, call: 1-800-807-6777, or visit our website at www.jennair.ca.

MANUAL DE INSTALACIÓN

Si tiene preguntas respecto a las características, funcionamiento, rendimiento, partes, accesorios o servicio técnico, llame al:

1-800-JENNAIR (1-800-536-6247) o visite nuestro sitio de internet: www.jennair.com.

En Canadá, llame al: 1-800-807-6777, o visite nuestro sitio de internet: www.jennair.ca.

Au Canada, pour assistance, installation ou service, composez le 1-800-807-6777 ou visitez notre site web à www.jennair.ca.

Table of Contents/Índice/Table des matières ......................................................................................2

W10297654A

INSTALLATION GUIDE

GUIDE D’INSTALLATION

TABLE OF CONTENTS

REFRIGERATOR SAFETY...........................................................................3

36" MODELS ................................................................................................4

Accessories...............................................................................................5

42" FRENCH DOOR MODELS....................................................................6

Accessories...............................................................................................7

INSTALLATION REQUIREMENTS .............................................................7

Tools and Parts.........................................................................................7

Location Requirements.............................................................................9

Electrical Requirements..........................................................................10

Water Supply Requirements...................................................................10

Product Dimensions ...............................................................................11

Tipping Radius........................................................................................11

Door Swing Dimensions .........................................................................12

Cabinet and Panel Installation Options..................................................12

Fully Integrated Installation Requirements.............................................13

Standard Installation-Wood Panel Requirements..................................14

ÍNDICE

SEGURIDAD DEL REFRIGERADOR........................................................27

MODELOS DE 36" .....................................................................................28

Accesorios ..............................................................................................29

MODELOS DE DOS PUERTAS CON CONGELADOR

EN LA PARTE INFERIOR, DE 42" ............................................................30

Accesorios ..............................................................................................31

REQUISITOS DE INSTALACIÓN ..............................................................32

Piezas y herramientas.............................................................................32

Requisitos de ubicación .........................................................................33

Requisitos eléctricos...............................................................................34

Requisitos del suministro de agua .........................................................35

Dimensiones del producto......................................................................35

Arco de vuelco........................................................................................36

Medidas de oscilación de las puertas....................................................36

Opciones para la instalación del armario y los paneles......................... 37

Requisitos para la instalación completamente incorporada..................37

Panel Kit Installation Requirements........................................................ 14

Custom Wood Overlay Panels ............................................................... 15

Custom Wood Overlay Panel Dimensions............................................. 15

INSTALLATION INSTRUCTIONS .............................................................16

Unpack the Refrigerator .........................................................................16

Move the Refrigerator into House .......................................................... 17

Install Anti-Tip Boards ............................................................................17

Connect the Water Supply .....................................................................17

Plug in Refrigerator.................................................................................19

Move Refrigerator to Final Location....................................................... 19

Level and Align Refrigerator ................................................................... 20

Install Refrigerator and Panels ...............................................................20

Install Handles ........................................................................................ 26

Install Base Grille .................................................................................... 26

Complete Installation..............................................................................27

Instalación estándar Requisitos para el panel de madera..................... 38

Requisitos de instalación del juego de paneles.....................................39

Paneles de madera recubiertos a la medida.......................................... 40

Dimensiones de los paneles de madera recubiertos............................. 40

INSTRUCCIONES DE INSTALACIÓN...................................................... 41

Desempaque el refrigerador...................................................................41

Cómo introducir el refrigerador en la casa............................................. 42

Cómo instalar los tableros antivuelco .................................................... 42

Conexión del suministro de agua...........................................................42

Cómo enchufar el refrigerador ............................................................... 44

Cómo mover el refrigerador a su ubicación final ................................... 44

Nivelación y alineamiento del refrigerador ............................................. 45

Instalación del refrigerador y los paneles...............................................45

Instalación de las manijas.......................................................................51

Instalación de la rejilla de la base........................................................... 52

Cómo terminar la instalación..................................................................52

SÉCURITÉ DU RÉFRIGÉRATEUR ...........................................................53

MODÈLES DE 36"......................................................................................54

Accessoires.............................................................................................55

MODÈLES DE PORTE À DOUBLE BATTANT DE 42"............................56

Accessoires.............................................................................................57

EXIGENCES D’INSTALLATION................................................................58

Outillage et pièces ..................................................................................58

Exigences d'emplacement .....................................................................59

Spécifications électriques ......................................................................60

Spécifications de l’alimentation en eau..................................................61

Dimensions du produit............................................................................61

Rayon de basculement...........................................................................62

Dimensions pour l’ouverture des portes ................................................62

Options d’installation du placard et du panneau ...................................63

Exigences d’une installation totalement intégrée...................................63

Installation standard Spécifications pour panneau en bois...................64

TABLE DES MATIÈRES

Spécifications pour l’installation de l’ensemble de panneaux............... 65

Panneaux de bois décoratifs personnalisés .......................................... 65

Dimensions des panneaux de bois décoratifs.......................................66

INSTRUCTIONS D’INSTALLATION .........................................................67

Déballage du réfrigérateur...................................................................... 67

Déplacement du réfrigérateur dans le domicile ..................................... 67

Installation de planches antibasculement..............................................68

Raccordement à l'alimentation en eau...................................................68

Brancher le réfrigérateur.........................................................................70

Déplacement du réfrigérateur à son emplacement définitif................... 70

Réglage de l'aplomb et alignement du réfrigérateur.............................. 71

Installation du réfrigérateur et des panneaux......................................... 72

Installation des poignées........................................................................77

Installation de la grille de la base ...........................................................78

Achever l’installation...............................................................................79

REFRIGERATOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

You can be killed or seriously injured if you don't immediately

DANGER

WARNING

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

WARNING

follow instructions.

can be killed or seriously injured if you don't

You instructions.

Tip Over Hazard

Refrigerator is top heavy and tips easily when not completely installed.

Keep doors taped closed until refrigerator is completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

36" MODELS

Integrated Design

Features custom-made panels and custom hardware provided by the cabinetmaker for a seamless appearance designed to blend with existing kitchen cabinetry.

Base Model Numbers: JB36NXFXLW, JB36NXFXRW

Pro-Style

Features stainless steel wrapped doors and Pro-Style® handles with diamond-etched grip.

Base Model Numbers: JB36NXFXLW, JB36NXFXRW Kit Model Number: JPK36BNXWPS

Stainless Design

Euro-Style Stainless Design

Features stainless steel wrapped doors and new Euro-style handles designed to compliment the Jenn-Air Euro kitchen suite or enhance any kitchen decor.

Base Model Numbers: JB36NXFXLW, JB36NXFXRW Kit Model Number: JPK36BNXWES

Classic Euro-Style Design

Features stainless steel wrapped doors with towel bar-style handles to enhance the traditional stainless kitchen appearance.

Base Model Number: JB36NXFXDW Kit Model Number: JB36BNXWSS

Floating Glass Design

Classic black or white glass panels that seemingly float in place with slightly curved, color coordinating handles that will compliment your contemporary kitchen.

Base Model Number: JB36NXFXDW Kit Model Numbers: JPK36BNXWSY, JPK36BNXWSF

Accessories

All factory parts are available through your Jenn-Air dealer or by calling Jenn-Air at 1-800-JENNAIR (1-800-536-6247). In Canada, call 1-800-807-6777.

Door Handle Kits

Follow the kit instructions for installation.

Pro-Style Euro-Style Stainless Steel - BM W10250635 Classic Euro-Style - BM W10250638

Stainless Steel - BM W10250641

Armoire-Style Door Panel Kit

Follow the kit instructions for installation. 36" Model - W10292391

42" FRENCH DOOR MODELS

Integrated Design

Uses custom-made panels and custom hardware provided by the cabinetmaker for a seamless appearance designed to blend with existing kitchen cabinetry.

Base Model Number: JF42NXFXDW

Pro-Style

Features stainless steel wrapped doors and Pro-Style® handles with diamond-etched grip.

Base Model Number: JF42NXFXDW Kit Model Number: JPK42FNXWPS

Stainless Design

Euro-Style Stainless Design

Features stainless steel wrapped doors and new Euro-style handles designed to compliment the Jenn-Air Euro kitchen suite or enhance any kitchen decor.

Base Model Number: JF42NXFXDW Kit Model Number: JPK42FNXWES

Classic Euro-Style Design

Features stainless steel wrapped doors with towel bar-style handles to enhance the traditional stainless kitchen appearance.

Base Model Number: JF42NXFXDW Kit Model Number: JPK42FNXWSS

Oiled-Bronze Design

Features intricate copper strokes that integrate seamlessly into your kitchen while slightly curved matching handles add to the refrigerator’s expressive form.

Base Model Number: JF42NXFXDW Kit Model Number: JPK42FNXWSR

Floating Glass Design

Classic black or white glass panels that seemingly float in place with slightly curved, color coordinating handles that will compliment your contemporary kitchen.

Base Model Number: JF42NXFXDW Kit Model Numbers: JPK42FNXWSY, JPK42FNXWSF

Accessories

All factory parts are available through your Jenn-Air dealer or by calling Jenn-Air at 1-800-JENNAIR (1-800-536-6247). In Canada, call 1-800-807-6777.

Door Handle Kits

These handle kits can be ordered to use on custom wood overlay panels. Follow the kit instructions for installation.

Pro-Style

Stainless Steel FDBM - W10250642 Euro-Style Stainless Steel FDBM - W10250636 Classic Euro-Style FDBM - W10250639

INSTALLATION REQUIREMENTS

Tools and Parts

IMPORTANT:

■ Installer: Leave Installation Instructions with the homeowner.

■ Homeowner: Keep Installation Instructions for future

reference. Save these Installation Instructions for the local electrical inspector’s use.

Armoire-Style Door Panel Kit

Follow the kit instructions for installation.

42" Model - W10292393

TOOLS NEEDED:

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

■ Cordless drill

■ Drill bits

■ Two adjustable

wrenches

■ Phillips screwdriver

■ Small level

■ ³⁄₃₂" Allen wrench

(panel kits only)

■ ¹¹⁄₃₂" nut driver

■ ³⁄₈" and ¹⁄₂" open-end wrenches

■ ⁵⁄₃₂" and ³⁄₁₆" Allen wrench

■ ¹⁄₄" and ⁵⁄₁₆" socket drivers

■ Tape measure

■ Utility knife

■ Tap e (p ai nt er s)

■ Appliance dolly

PARTS NEEDED:

■ Six #8 x 3" (7.6 cm) wood screws (longer screws may be needed)

■ One or two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) wood board(s)

■ Custom wood overlay panels - consult a qualified

cabinetmaker or carpenter to make the custom wood panels. See “Custom Wood Overlay Panels” for more information.

Panel kits - See “36" Models or 42" French Door Models” for panel kit information.

■ Flexible, codes approved water supply tubing, a ferrule, a

union and a ¹⁄₄" (6.35 mm) compression fitting.

PARTS PROVIDED:

Integrated Grille Bracket

W10260890 - Left W10260891 - Right

“L” Bracket

W10234199

Slotted hex head screw

W10141645 (21)

Hex head blunt screw

W10142233 (4)

Phillips head flat screw

8281251 (28)

Door Adjustment Pin

Hex head pointed screw

W10141189 (4)

Round head screw

1163283 (24)

Door panel stud

W10129563

Door Stop Pin

Panel top bracket

W10192849

RC Hinge Cover Trim

W10199873 - 42" SxS W10199875 - 48" SxS W10202875 - 36" BM (Right) W10202510 - 42" FDBM (Right)

Side Trim

W10209363 - SxS W10207635 - 36" BM W10207633 - 36", 42" BM W10207632 - 36", 42" BM

Grille Trim

W10250961 - 36" BM W10250962 - 42" BM, SxS W10250963 - 48" SxS

FC Hinge Cover Trim

W10199886 - 42" SxS W10199888 - 48" SxS W10202877 - 36" BM (Left) W10202511 - 42" FDBM (Left)

Handle Side Door Trim

W10167367 - SxS W10188556 - BM (Left) W10202604 - BM (Right) W10202478 - FDBM (Right) W10202480 - FDBM (Left)

W10234194

Drawer Panel Bracket

W10234202

Standard Grille Bracket

W10182743 - Left

W10203457

W10182741 - Right

Installation block

W10234156

Panel templates

W10222280 - SxS W10222278 - Bottom Mount W10222282 - Grille

Location Requirements

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from refrigerator.

Failure to do so can result in death, explosion, or fire.

IMPORTANT:

■ Observe all governing codes and ordinances.

■ It is recommended that you do not install the refrigerator near

an oven, radiator, or other heat source.

■ Do not install in a location where the temperature will fall

below 55°F (13°C).

■ Floor must support the refrigerator weight, more than 600 lbs

(272 kg), door panels and contents of the refrigerator.

■ Ceiling height must allow for side tipping radius. See “Tipping

Radius.”

■ Location should permit door to open fully. See “Door Swing

Dimensions.”

■ Location must permit top grille removal. See “Opening

Dimensions.”

80" - 90"

(203-229 cm)

84" (213.4 cm) to bottom of solid soffit

Width

(see chart following)

(10.2 cm)

77" (196 cm)

Opening Dimensions

■ The width of the opening, from side to side, must be as

specified for your model, for at least 2" (5.08 cm) back from the face of the cabinet.

NOTE: If your opening does not meet this requirement, you will need to make modifications.

■ A solid soffit or wall cabinet must be installed 84" (213.4 cm)

above the floor. If the solid soffit is higher than 84" (213.4 cm) or one is not available, then the refrigerator must be braced.

If the anti-tip boards are needed, they must be attached to the rear wall studs so that there is 84" (213.4 cm) from the bottom of the anti-tip board to the floor. See “Install Anti-Tip Boards” for more information.

■ For a fully integrated installation, a minimum of 6" (15.24 cm)

of open space above the refrigerator is required. See “Fully Integrated Installation.” Anti-tip boards are required. See “Install Anti-Tip Boards” for more information.

■ A grounded 3 prong electrical outlet should be placed within

4" (10.2 cm) of the right side cabinets or end panel. See “Electrical Requirements” for more information.

■ The water shutoff should be located in the base cabinet on

either side of the refrigerator or some other easily accessible area. If the water shutoff valve is not in the cabinets, the plumbing for the water line can come through the floor. See “Water Supply Requirements” for more information.

(15.2 cm)

(2.54 cm)

(15.2 cm)

Model Width A (as shown above)

36 42

36" (91.4 cm) 42" (106.7 cm)

Installation Type Depth B (as shown above)

Standard Flush

25" (63.5 cm) minimum

(new installation) Retrofit Installations 24" (60.9 cm) minimum

IMPORTANT:

■ The width of the opening (Width A), must be as specified

for your model, for at least 2" (5.08 cm) back from the face of the cabinet.

NOTE: If your opening does not meet this requirement, you will need to make modifications.

■ Flooring under refrigerator must be at same level as the

room. Face of cabinetry must be plumb.

Electrical Requirements

WARNING

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

Before you move your refrigerator into its final location, it is important to make sure you have the proper electrical connection.

Recommended Grounding Method

A 115 Volt, 60 Hz., AC only, 15- or 20-amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord.

IMPORTANT: If this product is connected to a GFCI (Ground Fault Circuit Interrupter) protected outlet, nuisance tripping of the power supply may occur, resulting in loss of cooling. Food quality and flavor may be affected. If nuisance tripping has occurred, and if the condition of the food appears poor, dispose of it.

NOTE: Before performing any type of installation, cleaning, or removing a light bulb, remove the top grille and turn the master power switch to OFF or disconnect power at the circuit breaker box.

When you are finished, turn ON the master power switch or reconnect power at the circuit breaker box. Then reset the control to the desired setting.

Water Supply Requirements

■ All installations must meet local plumbing code requirements.

■ The water supply line must come up through the floor in the

gray shaded area shown.

■ The water shutoff should be located in the base cabinet on

either side of the refrigerator or some other easily accessible area. The right-hand side is recommended.

NOTE: There is not enough clearance to achieve a flush installation if a water shutoff valve is located in the wall behind the refrigerator.

(15.2 cm)

■ A ¹⁄₂" (12.7 mm) hole for plumbing should be drilled at least 6"

(15.2 cm) from the right or left hand side cabinet or panel. On the floor, the hole should be no more than 1" (2.54 cm) away from the back wall. See “Connect the Water Supply.”

■ If additional tubing is needed, use copper tubing and check

for leaks. Install the copper tubing only in areas where the household temperatures will remain above freezing.

■ Do not use a piercing-type or ³⁄₁₆" (4.76 mm) saddle valve

which reduces water flow and clogs more easily. NOTE: Your refrigerator dealer has a kit available with a ¹⁄₄"

(6.35 mm) saddle-type shutoff valve, a union, and copper tubing. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes.

(2.54 cm)

(15.2 cm)

Water Pressure

A cold water supply with water pressure between 30 and 120 psi (207 and 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualified plumber.

Reverse Osmosis Water Supply

IMPORTANT: The pressure of the water supply coming out of a

reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 and 120 psi (207 and 827 kPa).

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to be a minimum of 40 to 60 psi (276 to 414 kPa).

If the water pressure to the reverse osmosis system is less than 40 to 60 psi (276 to 414 kPa):

■ Check to see whether the sediment filter in the reverse

osmosis system is blocked. Replace the filter if necessary.

■ Allow the storage tank on the reverse osmosis system to refill

after heavy usage.

■ If your refrigerator has a water filter, it may further reduce the

water pressure when used in conjunction with a reverse osmosis system. Remove the water filter cartridge.

If you have questions about your water pressure, call a licensed, qualified plumber.

Product Dimensions

IMPORTANT:

■ The depth from the front face of the doors to the back of the

refrigerator cabinet is 24" (60.96 cm) without panels.

■ The power cord is 84" (213 cm) long.

■ The water supply line is located at the front of the refrigerator.

42" French-Door Bottom-Mount

Top Vi ew

36" Bottom-Mount

Top Vi ew

24"

(61.0 cm)

35³⁄₄"

(90.8 cm)

Front View

■ Width dimensions were measured from hinge edge to clip

edge.

35³⁄₄"

(90.8 cm)

24"

(61.0 cm)

41³⁄₄"

(106.1 cm)

Front View

■ Width dimensions were measured from hinge edge to hinge

edge.

41³⁄₄"

(106.1 cm)

84" (213.4 cm)

Tipping Radius

Be sure there is adequate ceiling height to stand the refrigerator upright when it is moved into place.

■ The dolly wheel height must be added to the tipping radius

when a dolly is used.

■ If needed, the tipping radius can be reduced. See “Reduce

Tipping Radius.”

NOTE: Tip on side only.

Side Tipping Radius (36" [91.4 cm] Models)

Cabinet and Panel Installation Options

Cabinet Depth - 25" (63.5 cm)

Framed Cabinetry

Top V iew

A. 88

⁷⁄₈

" (225.7 cm)

Side Tipping Radius (42" [106.7 cm] Models)

A. 91

³⁄₈

" (232.1 cm)

Door Swing Dimensions

The location must permit both doors to open to a minimum of 90°. Allow 4¹⁄₂" (11.4 cm) minimum space between the side of the refrigerator and a corner wall.

NOTE: More clearance may be required if you are using custom wood overlay panels, custom handles, or extended handles.

A. Refrigerator door B. Overlay panel C. Side trim

Top V iew - I ns et

A. Refrigerator door B. Overlay panel C. Side trim

E D C

A B

D. Adjacent cabinet

E. Grille bracket

E D C

A B

D. Adjacent cabinet

E. Grille bracket

BA C D

90˚

110˚

90˚

110˚

Model A B C D

36 36"

(91.4 cm)

42 42"

(106.7 cm)

39³⁄₄" (101.0 cm)

42" (106.7 cm)

45³⁄₈" (115.3 cm)

48⁵⁄₈" (123.5 cm)

46³⁄₄" (118.8 cm)

50¹⁄₄" (127.6 cm)

Frameless Cabinetry

A B

A. Refrigerator door B. Overlay panel C. Side trim

E D C

D. Adjacent cabinet

E. Grille bracket

Cabinet Depth - 24" (60.9 cm)

NOTE: A flush installation is not possible with a 24" (60.9 cm) deep opening.

Framed Cabinetry

Top View

E D

Fully Integrated Installation - Side View

A B

A. Refrigerator door B. Overlay panel C. Side trim

D. Adjacent cabinet

E. Grille bracket

Frameless Cabinetry

Top V iew

E D C

A B

A. Refrigerator door B. Overlay panel C. Side trim

D. Adjacent cabinet

E. Grille bracket

Fully Integrated Installation Requirements

The refrigerator can be installed fully integrated if the adjacent cabinetry meets the airflow venting requirements critical to refrigerator performance.

IMPORTANT:

■ A Fully Integrated installation can be achieved with either a

24" (60.9 cm) or 25" (63.5 cm) deep opening.

■ A full height grille is used to achieve a Fully Integrated

installation. Use the integrated grille bracket (provided with refrigerator) to attach the full height grille.

NOTE: A top grille vent is not required with a full height grille.

Integrated Grille Bracket

A. False front (optional) B. Airflow

C. Full height grille D. Door panel

Airflow Venting Requirements

Fully integrated installations require a minimum of 6" (15.24 cm) of open space above the refrigerator. This space must not be blocked in any way, including soffits.

Option 1 - Open to Ceiling

6" (15.24 cm)

min.

84"

(213.4 cm)

Option 2 - False Front (cabinet face only)

6" (15.24 cm) min.

84"

(213.4 cm)

Standard Installation - Side View

Standard Installation - Full Product View

Standard Installation-Wood Panel

Requirements

IMPORTANT:

■ A Standard installation can be achieved with either a 24"

(60.9 cm) or 25" (63.5 cm) deep opening.

■ A standard grille is used to achieve a Standard installation.

Use the standard grille bracket (provided with refrigerator) to attach the standard grille.

■ The grille panel height, shown in the Standard Installation

Flush Grille graphic, allows for an air gap critical to refrigerator performance.

Standard Grille Bracket

Panel Kit Installation Requirements

See the “36" Models” or the “42" French Door Models” section to see the panel kit options available for your model.

IMPORTANT:

■ A Panel Kit installation can be achieved with either a 24"

(60.9 cm) or 25" (63.5 cm) deep opening.

■ A standard grille is used to achieve a Panel Kit installation.

Use the standard grille bracket (provided with refrigerator) to attach the standard grille.

■ The grille panel height, shown in the Standard Installation

Flush Grille graphic, allows for an air gap critical to refrigerator performance.

Standard Grille Bracket

Panel Kit Installation - Side View

Custom Wood Overlay Panels

Custom wood overlay panels allow you to blend the exterior of your refrigerator into the overall kitchen décor and to use custom handles for additional design flexibility.

In some cases, your cabinet manufacturer may choose to work with one panel routed for the different dimensions. Follow these panel dimension and placement instructions to be sure that the custom wood overlay panels will fit properly.

IMPORTANT:

■ For 36" (91.4 cm) models, the refrigerator door wood overlay

panel cannot exceed 60 lbs (27.2 kg) and the freezer drawer overlay panel cannot exceed 25 lbs (11.3 kg).

■ For 42" (106.7 cm) models, the refrigerator door wood overlay

panel cannot exceed 38 lbs (17.2 kg) and the freezer drawer overlay panel cannot exceed 30 lbs (13.6 kg).

■ The weight of the top grille wood overlay panel cannot exceed

7 lbs (3.2 kg) for both models.

■ The required thickness for all panels is ³⁄₄" (1.91 cm).

■ This installation does not require filler or backer panels.

Custom Wood Overlay Panel Dimensions

36" (91.4 cm) Model - Door and Drawer Panels

Panel Kit Installation - Full Product View

52³⁄₈"

(133.03 cm)

20¹⁄₂"

(52.07 cm)

REFRIGERATOR DOOR PANEL

Maximum Weight: 60 lbs (27.2 kg)

FREEZER DRAWER PANEL

Maximum Weight: 25 lbs (11.34 kg)

CAUTION

Pinch Hazard

Installation of door panels with less than a ³⁄₈" (0.95 cm) gap between the door panel and the adjacent cabinet increases the risk of potential pinching.

Model 36" Bottom-Mount Reveal ³⁄₈" ¹⁄₈" A 35¹⁄₄" (89.54 cm) 35³⁄₄" (90.81 cm) B 35¹⁄₄" (89.54 cm) 35³⁄₄" (90.81 cm)

42" (106.7 cm) Model - Door and Drawer Panels

52³⁄₈"

(133.03 cm)

REFRIGERATOR

DOOR PANEL

Maximum Weight:

38 lbs (17.2 kg)

REFRIGERATOR

DOOR PANEL

Maximum Weight:

38 lbs (17.2 kg)

Standard Installation - Flush Grille - Open or Closed Soffit

1" (2.54 cm)

³⁄₄"

(14.55 cm)

Model 36 42 Reveal ³⁄₈" ¹⁄₈" ³⁄₈" ¹⁄₈" D 35¹⁄₄"

(89.54 cm)

E 35¹⁄₄

(89.54 cm)

35³⁄₄" (90.81 cm)

IMPORTANT: The grille panel height, shown in the Standard Installation Flush Grille graphic, allows for an air gap critical to refrigerator performance.

Top Grille Filler

Top Grille Panel

41¹⁄₄" (104.76 cm)

41³⁄₄" (106.05 cm)

20¹⁄₂"

(52.07 cm)

FREEZER DRAWER PANEL

Maximum Weight: 30 lbs (13.6 kg)

CAUTION

Pinch Hazard

Installation of door panels with less than a ³⁄₈" (0.95 cm) gap between the door panel and the adjacent cabinet increases the risk of potential pinching.

Model 42" French Door Bottom-Mount Reveal ³⁄₈" ¹⁄₈" A 20⁹⁄₁₆" (52.23 cm) 20¹³⁄₁₆" (52.86 cm) B 41¹⁄₄" (104.76 cm) 41³⁄₄" (106.05 cm)

Grille Panel

Integrated Installation - Full Height Grille - Open Soffit

⁵⁄₈"

(16.83 cm)

Model 36 42 Reveal ³⁄₈" ¹⁄₈" ³⁄₈" ¹⁄₈" C 35¹⁄₄"

(89.54 cm)

35³⁄₄" (90.81 cm)

Top Grille Panel

41¹⁄₄" (104.76 cm)

41³⁄₄" (106.05 cm)

INSTALLATION INSTRUCTIONS

Unpack the Refrigerator

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not completely installed.

Keep doors taped closed until refrigerator is completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

IMPORTANT:

■ Do not remove the film covering until the refrigerator is in its

operating location.

■ All four leveling legs must contact the floor to support and

stabilize the full weight of the refrigerator.

■ Keep the cardboard shipping piece or plywood under the

refrigerator until it is installed in the operating location.

1. Remove and save the literature package and hardware kit

located inside the refrigerator. Remove and save the literature, grille, and trim taped to the outside of the refrigerator.

NOTE: Do not remove tape and door bracing until the refrigerator is in its final location.

Move the Refrigerator into House

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not completely installed.

Keep doors taped closed until refrigerator is completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

1. Place an appliance dolly under the left side of the refrigerator

as shown. Place the corner posts from the packing materials over the trims as appropriate. Slowly tighten the strap.

To Install Anti-tip Boards

1. Mark the stud locations on rear wall 80" to 90" (203 cm to

229 cm) above floor.

2. Securely attach one or two 2" x 4" x 32" (5 cm x 10 cm x

81 cm) boards to wall studs behind refrigerator. Use six #8 x 3" (7.6 cm) (or longer) wood screws. The wood screws must be screwed into the studs at least 1½" (3.8 cm). The board(s) must overlap the compressor cover.

¹⁄₄" (6 mm)

max.

2" (5 cm)

84"

(213.4 cm)

2. Place pieces of the shipping carton on the floor when rolling

the dolly and refrigerator into the house. Move the refrigerator close to the built-in opening.

3. Place top of cardboard carton or plywood under refrigerator.

4. Stand the refrigerator up. First, place the left bottom edge of

the refrigerator on the floor, stand the refrigerator upright and then lower the right-hand side of the refrigerator to the floor.

Install Anti-Tip Boards

IMPORTANT:

■ If a solid soffit is not available, an anti-tip board must be

installed.

■ It is recommended that board(s) be installed before the

refrigerator is installed.

■ Board(s) must be long enough to fully cover the width of the

compressor cover.

■ Locate the board(s) so the bottom surface(s) of the board(s)

is(are) 84" (213 cm) from the floor.

■ During installation, raise the refrigerator up until the top of the

refrigerator is making contact with the bottom of the anti-tip board(s). Do not crush the compressor cover when raising the rear leveling legs.

A. Center board B. Two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards

C. Attach to studs with six #8 x 3" (7.6 cm) screws

D. Compressor cover E. Distance from bottom of anti-tip board to floor

¹⁄₄

" (6.35 mm) max. above refrigerator

Connect the Water Supply

Read all directions before you begin. IMPORTANT: If you turn the refrigerator on before the water line is

connected, turn the ice maker OFF.

Connect to Water Line

Parts Needed:

■ Minimum 7 ft (2.13 m) flexible, codes approved water

supply line

Style 1 - Shutoff Valve Connection

NOTE: If your water line connection does not look like Style 1, see

“Style 2 - Copper Line Connection.”

1. Unplug refrigerator or disconnect power supply. IMPORTANT: Before attaching the tubing to shutoff valve, flush

the main water supply line to remove particles and air in the water line. Allow enough flow so that water becomes clear. Flushing the water line may help avoid filters and/or water valves from becoming clogged.

2. Connect the flexible, codes approved water supply line to the

A B

water shutoff valve by threading the provided nut onto the shutoff valve as shown.

NOTE: The shutoff valve shown is in the side cabinet as recommended.

A. Bulb B. Nut

C. Water tubing

3. Place the end of the tubing into a bucket, and turn shutoff

valve ON.

4. Check for leaks. Tighten any nuts or connections (including

connections at the valve) that leak.

Style 2 - Copper Line Connection

NOTE: If there is a water supply line that meets the specifications

in “Water Supply Requirement” proceed to “Connecting to Refrigerator.” If not, use the following instructions to connect to the household cold water supply.

1. Unplug refrigerator or disconnect power.

2. Turn OFF main water supply. Turn ON nearest faucet long

enough to clear line of water.

3. Locate a ½" to 1¹⁄₄" (1.25 cm to 3.18 cm) vertical cold water

pipe near the refrigerator.

IMPORTANT:

■ Make sure it is a cold water pipe.

■ Horizontal pipe will work, but drill on the top side of the

pipe, not the bottom. This will help keep water away from the drill and normal sediment from collecting in the valve.

4. Determine the length of copper tubing you need. Measure

from the connection on the lower left rear of refrigerator to the water pipe. Add 7 ft (2.1 m) to allow for cleaning. Use ¹⁄₄" (6.35 mm) O.D. (outside diameter) copper tubing. Be sure both ends of copper tubing are cut square.

5. Using a cordless drill, drill a ¹⁄₄" (6.35 mm) hole in the cold

water pipe you have selected.

6. Fasten the shutoff valve to the cold water pipe with the pipe

clamp. Be sure the outlet end is solidly in the ¹⁄₄" (6.35 mm) drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws slowly and evenly so washer makes a watertight seal. Do not overtighten.

IMPORTANT: Before attaching the tubing to shutoff valve, flush the main water supply line to remove particles and air in the water line. Allow enough flow so that water becomes clear. Flushing the water line may help avoid filters and/or water valves from becoming clogged.

7. Slip the compression sleeve and compression nut on the

copper tubing as shown. Insert the end of the tubing into the outlet end squarely as far as it will go. Screw compression nut onto outlet end with adjustable wrench. Do not overtighten the clamp or the sleeve. This will crush the copper tubing.

8. Turn off the shutoff valve on the water pipe. Coil the copper

tubing.

9. Connect the flexible, codes approved water supply line to the

water shutoff valve by threading the provided nut onto the shutoff valve.

10. Place the end of the tubing into a bucket, and turn shutoff

valve ON.

11. Check for leaks around the saddle valve. Tighten any nuts or

connections (including connections at the valve) that leak.

Connect to Refrigerator

Parts Supplied:

■ ¹⁄₄" to ¹⁄₄" (6.35 mm to 6.35 mm) male-to-male coupling

7" (17.78 cm)

(2.54 cm)

DEF

A. Cold water pipe

B. Pipe clamp C. Copper tubing D. Compression nut

E. Compression sleeve F. Shutoff valve

G. Packing nut

NOTE: The flexible, codes approved water supply line can

connect to the supply valve through the floor or through the side cabinets, as indicated by the gray boxes above.

1. Unplug the refrigerator or disconnect power.

2. Connect the 7 ft (2.13 m) flexible codes approved water tube

to the water supply valve.

3. Flush the main water supply line to remove particles and air in

the water line. Allow enough flow so that water becomes clear.

4. Tape the 7 ft (2.13 m) flexible codes approved water supply

line to the floor, 7" (17.78 cm) from the left side of the refrigerator. Tape along the length of the tubing, which will allow it to pass beneath the refrigerator without interference.

NOTE: Allow a minimum of 26" (66.04 cm) of flexible codes approved water supply line to be loose at the front of the refrigerator for connecting to the refrigerator.

5. Connect the 7 ft (2.13 m) flexible codes approved water

supply line to the refrigerator. NOTE: If the main water shutoff valve is behind the

refrigerator, a secondary water shutoff valve may be installed in line with the water supply line at the front of the product.

A. Household water line B. Nut (purchased) C. Ferrule (purchased) D. Coupling

6. Turn on the water supply valve and check all connections for

leaks.

7. Plug in the refrigerator or reconnect power.

8. Flush the water system. See “Water System Preparation.” NOTE: Allow 24 hours to produce the first batch of ice.

Discard the first three batches of ice produced. Allow 3 days to completely fill ice container.

E. Bulb F. N u t

G. Refrigerator water tubing

Plug in Refrigerator

WARNING

Move Refrigerator to Final Location

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not completely installed.

Keep doors taped closed until refrigerator is completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

IMPORTANT:

■ To avoid floor damage, make sure levelers are raised (not

touching floor) and refrigerator is on rollers before moving.

■ Use the installation block, attached to the door hinge, as a

reference to make sure the refrigerator is pushed back far enough into the opening, so that when the panels are installed they will be flush with the adjacent cabinets.

NOTE: A flush installation is not possible with a 24" (60.9 cm) deep opening.

■ After the refrigerator is leveled and aligned, remove the

installation block from the door hinge and use it to check the spacing between the panels and adjacent cabinets.

NOTE: The installation block is designed to provide accurate spacing for ³⁄₄" (1.9 cm), ³⁄₈" (9.53 mm) and ¹⁄₈" (3.18 mm).

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

1. Set control switch at top of cabinet to the OFF position.

2. Plug into a grounded 3 prong outlet.

³⁄₄"

(1.9 cm)

³⁄₈"

(9.53 mm)

1. Place top of cardboard carton or plywood under refrigerator.

Remove dolly.

2. Move the refrigerator straight back and evenly into the

opening. Be sure that the water tubing is not kinked and the power supply cord is on top of the refrigerator.

NOTE: If the power supply cord is behind the refrigerator, it will not install properly.

3. Make sure the installation block is flush with the adjacent

cabinets.

¹⁄₈"

(3.18 mm)

NOTE: To achieve a flush installation, it is critical to verify a ³⁄₄"

A B

(1.9 cm) depth from the front face of the adjacent cabinetry to the refrigerator.

3. Continue adjusting all of the leveling legs to raise the

refrigerator until the top is within at least ¹⁄₄" (6.35 mm) of the top soffit as shown.

NOTE: If an anti-tip board has been used, adjust the leveling legs until the top of the refrigerator is making contact with the bottom of the anti-tip board(s). Do not crush the compressor cover.

³⁄₄" (1.9 cm)

A. Adjacent cabinet or wall B. Installation block C. Face of refrigerator

Level and Align Refrigerator

WARNING

Tip Over Hazard

Refrigerator is top heavy and tips easily when not completely installed.

Keep doors taped closed until refrigerator is completely installed.

Use two or more people to move and install refrigerator.

Failure to do so can result in death or serious injury.

¹⁄₄" (6 mm)

max.

2" (5 cm)

84"

(213.4 cm)

A. Center board B. Two 2" x 4" x 32" (5 cm x 10 cm x 81 cm) boards C. Attach to studs with six #8 x 3" (7.6 cm) screws D. Compressor cover E. Distance from bottom of anti-tip board to floor

IMPORTANT: Adjust in small increments to keep from damaging the cabinet trim and causing problems with the door alignment or top grille fit. To avoid damage to the cabinet or leveling legs, do not apply more than 50 inch-pounds (5.65 Nm) of torque to the leveling bolts. The leveling legs can be extended to a maximum of 1¹⁄₄" (3.18 cm) below the rollers.

4. After leveling the refrigerator, use a straight edge or 4 foot

level going across the front of the refrigerator installation to the cabinets to check that the refrigerator is still flush.

¹⁄₄

" (6.35 mm) max. above refrigerator

IMPORTANT: All four leveling legs must contact the floor to support and stabilize the full weight of refrigerator. Rollers are for moving refrigerator and not for permanent support.

After moving the refrigerator to its final location:

1. Use a ⁵⁄₁₆" socket driver to turn the leveling bolts clockwise to

extend the legs to the floor as shown. The rollers should be off the floor.

A B

A. Rear leveling bolt B. Front leveling bolt

2. Adjust the leveling legs to level and align the refrigerator from

left to right and front to back so that the refrigerator is level and aligned with the cabinets.

Install Refrigerator and Panels

IMPORTANT: Jenn-Air is not responsible for the removal or addition of molding or wood overlay panels that would not allow access to the refrigerator for service.

Install Refrigerator to Adjacent Cabinets

1. Open the refrigerator door(s) and freezer drawer. On the hinge

side(s), locate the cabinet brackets in the space between the door(s) and the refrigerator and the drawer and refrigerator.

2. Using the holes in the brackets as a template, predrill

pilot holes into the adjacent cabinet.

3. Using two round head screws (provided with refrigerator) for

each bracket, insert the screws through the cabinet brackets and into the adjacent cabinetry to anchor the refrigerator.

4. Repeat steps 2 and 3 to anchor the other side of the

refrigerator to the adjacent cabinetry.

Install Cabinet Side Trims

Install cabinet side trims to hide the brackets fastening the refrigerator to the adjacent cabinets.

1. Open the door(s) to a 90° angle.

2. With the lip edge of the trim toward the back wall, insert the

cabinet side trim between the side of the refrigerator and the adjacent cabinetry.

¹⁄₈" deep

NOTE: Keep the top edge of the trim piece flush with the top

of the refrigerator. If the trim is installed so that the top of the trim is higher than the top of the refrigerator, damage to the trim could occur when the refrigerator door is opened.

3. Slide the trim toward the back until it snaps into place.

Side View

A. Cabinet side trim B. Refrigerator door

Install Top Grille Filler (standard installation only)

IMPORTANT: The grille panel height allows the necessary airflow

for refrigerator performance. The top grille filler hides the upper compartment cover behind the top grille. If you choose to modify the recommended grille panel dimensions, performance will be compromised.

Custom Wood Panel Models

1. In the custom made (1" x width of grille panel) wood filler

piece, drill a hole NOTE: Make sure the hole is centered in the 1" thickness of

the wood piece.

2. Using slotted hex head screws (provided with refrigerator),

fasten an “L” bracket to each end of the wood filler piece.

3. Using hex head blunt screws (provided with refrigerator),

attach the “L” brackets to the top grille mounting plates.

4. Adjust the “L” brackets, so that the wood filler piece is flush

with the bottom of the soffit. Completely tighten the screws.

¹¹⁄₁₆" from each edge.

A. Top grille filler B. Soffit C. Airflow

D. Grille panel

E. Door panel

Panel Kit Models

WARNING

Excessive Weight Hazard Use two or more people to move and install panels. Failure to do so can result in back or other injury.

WARNING

Broken Glass Hazard Do not hit refrigerator glass doors. Protect glass surface and edges during installation or

removal of doors. Failure to do so can result in serious eye injury or

minor cuts.

A. Custom wood filler B. “L” bracket

C. Grille mounting plate

1. Align top grille vent (provided in the door kit) with the bottom

edge of the soffit. Use as a template, and mark where to drill the holes.

2. Using slotted hex head screws (provided with refrigerator),

attach the top grille vent to the soffit.

A. Top grille vent B. Slotted hex head screw

Side View

Prepare Panels (custom wood and panel kits)

IMPORTANT: The process for installing wood overlay panels on

the refrigerator is the same for both custom wood panels and panel kits.

Door Panel

1. Place panel(s) on a firm, flat surface with the front facing

down.

2. Locate the two pre drilled holes in the handle side edge of the

door panel.

3. Using the installation block as a guide for depth, screw the

door studs (provided with refrigerator) into the pre drilled door panel (two door panel studs per door).

A. Soffit B. Airflow

C. Grille panel D. Door panel

Predrill Panels (custom wood panels only)

IMPORTANT: The template can be used for either a ³⁄₈" (0.95 cm)

or a ¹⁄₈" (0.32 cm) reveal installation.

■ The drilling templates are used only for custom wood overlay

panels.

■ The drilling templates are double-sided.

■ The drilling holes are precut into the template.

1. On the template, locate the diagram of your refrigerator. Then,

follow the letters and colored arrows to correctly place the drilling template on the panels.

2. Predrill ¹⁄₈" (0.32 cm) deep pilot holes into the wood rails

bordering the door(s), drawer and top grille panels.

Predrill Panels (panel kits only)

IMPORTANT: The panels included in the panel kits are marked for

the location of the mounting brackets only.

1. Predrill holes where marked. See “Complete Installation” later

in this section, for instructions on drilling additional holes in the door panels.

NOTE: For 36" model door panel kits which are right-hand swing and left-hand swing specific use the following instructions:

■ Hinge on right-hand side - Use the holes, located on the

back side of the door panel, that are circled in red.

■ Hinge on left-hand side - Use the holes, located on the

back side of the door panel, that are circled in blue.

2. Remove the film covering on stainless steel door panels

before installing brackets.

A. Door panel stud B. Installation block

4. For the mounting bracket, insert the hex head pointed screws

(provided with refrigerator) into the wood at the top of the door panels where they were pre drilled.

NOTES:

■ It is critical to use the ⁵⁄₈" screw, the longest length

provided, to attach the bracket to the top of the door panel. These hex head pointed screws are used only to attach this mounting bracket.

■ Panel Kits - Find the holes to attach the hex head pointed

screws by locating the slots in the door panel, not the U-shaped holes.

5. Attach a panel top bracket to the top edge of the door panel(s)

by placing the large ends of the keyhole slots over the screws and sliding the bracket so that the screws are centered in the slots.

NOTE: Start with the screws in the center of the slots as shown, then move the door panel, as necessary, to align.

A. Door panel B. Panel top bracket

Drawer Panel

1. Using the Phillips head flat screws (provided with refrigerator),

fasten a drawer panel bracket to each side of the drawer panel, as shown.

Remove Trim Pieces

1. Remove all tape and door bracing from the refrigerator and

freezer doors.

2. Open the refrigerator and freezer doors.

3. Remove the hinge cover trim pieces from the top and bottom

of the door to expose the holes in the hinges. NOTES:

■ It is not necessary to remove the hinge side trims as they

will not interfere with the installation

■ Leave the freezer drawer trims in place for installation.

4. Remove the handle side trims. See following graphic.

A. Drawer panel B. Drawer panel mounting bracket

Top Grille Panel

1. Using the slotted hex head screws (provided with refrigerator),

attach a mounting bracket to each side of the top grille panel. IMPORTANT: See the Parts Provided insert sheet to select

the brackets designated for your installation.

■ Use the Integrated Grille brackets for an Integrated

Installation with a full height grille.

■ Use the Standard Grille brackets for a Standard

Installation with a flush grille, as shown.

A. Hinge cover pieces B. Handle-side door trim

Install Door Panels

NOTE: French door models, first open the door opposite from the

one to which you are installing the door panel.

1. Lower the panel bracket onto the door adjustment pins at the

top of the door.

A. Top grille brackets B. Grille trim piece

2. Using round head screws (provided with refrigerator), attach

the grille trim piece to the bottom of the grill panel. NOTE: The grille trim is pre installed on the panel kits.

A. Door panel B. Panel top bracket

C. Adjustment pins

2. Locate the studs on the back of the door panel. Slide the

studs, top stud first followed by the bottom stud, into the “J” pockets in the front of the door.

NOTE: It is the washer in the stud, not the head of the stud, that is inserted in the “J” pocket.

3. Slide the door panel down into the “J” pocket.

4. French door models, repeat steps 1 through 3 to install the

second door panel.

5. Using a slotted hex head screw (provided with refrigerator),

attach the mounting bracket (factory installed), located at the bottom of the refrigerator door(s), to the respective door panel(s). Do not fully tighten the screw.

Install Top Grille Panel

B BA

A. Top grille panel B. Cabinet sides

Standard Installation - Flush Grille

1. Hook the panel brackets onto the mounting bolts extending

from the top of the refrigerator.

A B

A. Bottom hinge

B. Mounting bracket

Install Drawer Panel

1. Align the slots in the door panel brackets, located on each

side of the drawer panel, with the holes that go through the drawer trim and into the drawer.

2. Using Phillips head flat screws (provided with refrigerator),

attach the brackets to the drawer.

3. Move the drawer panel up and down or from side to side to

align. Do not fully tighten the screws.

A. Panel brackets B. Grill trim piece

2. Pull the grille panel down slightly to lock into place. Integrated Installation - Full Height Grille

1. Align the bracket on each side of the top grille panel with the

mounting bolts.

2. Push the grille panel forward until the bracket snaps into

place.

Door Swing Adjustment

It may be necessary to adjust the swing of the door(s). Make sure the refrigerator door(s) can open freely. If the door(s) opens too wide, install the door stop pin (provided with refrigerator).

1. Hold the door open to a position that is less than 90°.

2. Insert the door stop pin into the top hinge in the hole shown.

A. Drawer overlay panel B. Drawer panel bracket

+ 56 hidden pages

Jenn-Air W10297654A Installation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual