Jenn Air Tc507w, Tc507q, Tc507q1, Tc507s0, Tc507b1 Owner's Manual

...

JENN-AIR® COMPACTORS/COMPACTEURS

TC507

9871894A

Use & Care Guide

For assistance, call: 1-800-JENNAIR (1-800-536-6247).

Guide d’utilisation

et d’entretien

Pour assistance, composer le 1-800-JENNAIR (1-800-536-6247).

Table of Contents/Table des matières.............2

TABLE OF CONTENTS

TABLE DES MATIÈRES

COMPACTOR SAFETY.................................................................. 3

INSTALLATION INSTRUCTIONS..................................................4

Unpacking ....................................................................................4

Location Requirements................................................................4

Electrical Requirements ...............................................................5

Undercounter Installation.............................................................6

Air Freshener ................................................................................7

Changing the Decorative Panel ...................................................7

COMPACTOR USE.........................................................................9

How Your Compactor Works.......................................................9

Loading.......................................................................................10

Starting Your Compactor...........................................................10

Stopping Your Compactor.........................................................10

Removing a Filled Bag ...............................................................10

Installing a New Bag ..................................................................10

COMPACTOR CARE....................................................................11

Cleaning......................................................................................11

TROUBLESHOOTING ..................................................................12

RECYCLING WITH YOUR COMPACTOR ..................................13

ASSISTANCE OR SERVICE.........................................................14

In the U.S.A. and Canada ..........................................................14

Accessories................................................................................14

WARRANTY ..................................................................................15

SÉCURITÉ DU COMPACTEUR...................................................16

INSTRUCTIONS D’INSTALLATION.............................................17

Déballage....................................................................................17

Exigences d’emplacement.........................................................17

Spécifications électriques ..........................................................18

Installation sous un comptoir.....................................................19

Assainisseur d'air .......................................................................20

Changement du panneau décoratif ...........................................20

UTILISATION DU COMPACTEUR...............................................22

Fonctionnement du compacteur................................................22

Chargement................................................................................23

Mise en marche du compacteur................................................23

Pour arrêter le compacteur ........................................................23

Enlèvement d’un sac rempli.......................................................23

Installation d’un nouveau sac.....................................................23

ENTRETIEN DU COMPACTEUR.................................................24

Nettoyage ...................................................................................24

DÉPANNAGE.................................................................................25

RECYCLAGE AVEC VOTRE COMPACTEUR.............................26

ASSISTANCE OU SERVICE.........................................................27

Aux États-Unis et au Canada.....................................................27

Accessoires ................................................................................27

GARANTIE.....................................................................................28

COMPACTOR SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

You can be killed or seriously injured if you don't immediately

DANGER

WARNING

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

follow instructions.

can be killed or seriously injured if you don't

You instructions.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: When using an electrical appliance, basic precautions should always be followed, including the following:

■ Read all instructions before using the compactor.

■ Close supervision is necessary when used by or near

children. Do not allow to be used as a toy, or to run unattended at any time. Lock Key Switch when not in use and store key out of reach of children.

■ Do not touch moving parts.

■ Do not operate with a damaged cord set, plug, motor, or

after damage in any manner. Have the compactor examined, repaired or adjusted by an authorized serviceperson.

■ Use only for intended use as described in this manual. Do

not use other than manufacturer's recommended attachments.

■ Do not compact toxic or volatile flammable material such as

oily rags and insect sprays. Do not compact lighted cigarettes, cigars, or other hot or burning items. Do not overload the compactor.

■ Do not take apart the compactor. Incorrect reassembly can

cause electric shock when subsequently used.

■ Handle a loaded trash bag with care. Sharp objects can

pierce the bag and cause injury. Do not overload trash bag with heavy material such as glass.

■ This compactor is intended for household use only.

SAVE THESE INSTRUCTIONS

INSTALLATION INSTRUCTIONS

Installer: Leave Use and Care Guide with the homeowner. Homeowner: Keep Use and Care Guide for future reference and

for local electrical inspector’s use, if required.

Unpacking

WARNING

4. Place the other 2 corner posts on the floor to the side of the

compactor. Grasp the sides of the compactor cabinet and put compactor on its side on top of the corner posts. Remove the shipping base from the bottom of the compactor.

Excessive Weight Hazard Use two or more people to move and install compactor. Failure to do so can result in back or other injury.

IMPORTANT:

■ Do not grasp console to move compactor.

■ Begin in the room where the compactor will be located.

1. Remove compactor from shipping carton. Remove all

protective packaging materials such as tape and shipping pads. Use a mild detergent and warm water to remove waxy residue caused by protective shipping material. Dry thoroughly with a soft cloth. For more information, see “Cleaning.”

2. Be sure the power cord is attached to the cord clip on the

rear of the compactor.

A. Leveling legs B. Shipping base

Location Requirements

Product dimensions

34¹⁄₈"

(86.7 cm)

A. Cord clip

3. Place the 2 corner posts from the carton on the floor near the

compactor. Open the compactor drawer and remove any shipping materials or other items from the drawer. Do not remove the compactor bag. Grasp the handle and raise the front of drawer until it clears the drawer stops. Grasp sides of drawer and lift drawer out of compactor. Place the drawer on the 2 corner posts.

15"

(38.1 cm)

24"

(61 cm)

Cutout dimensions

(7.6 cm)

¹⁄₄

" min.

(87 cm)

24" min.

(61 cm)

A. Grounded electrical outlet must be a minimum of 3" (7.6 cm) away

from surrounding cabinets or nearby walls as shown. It can be placed either to the left or the right side of the product.

18" min.

(45.7 cm)

¹⁄₄

" min.

(38.7 cm)

Clearance dimensions

Electrical Requirements

WARNING

Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death,

fire, or electrical shock.

Recommended Grounding Method

This compactor is for use on a single phase, 115-volt, 60 Hz, AC only 15- or 20-amp fused and properly grounded circuit and is equipped with a grounding plug as shown below. It is recommended that a separate circuit serving only this appliance be provided.

A. Leave 6" (15.2 cm) of clearance space to the right side of the

compactor in order to remove the compactor bags.

B. Leave 23" (58.4 cm) of clearance in front of the compactor in order

to fully open or remove the compactor drawer.

This compactor must be grounded while in use to reduce the risk of electric shock. The compactor is equipped with a threeconductor cord and 3 prong grounding-type plug to fit the proper grounding-type receptacle. The green (or green and yellow) conductor in the cord is the grounding wire. Do not connect the green (or green and yellow) wire to a live terminal.

Undercounter Installation

NOTE: Proper installation is your responsibility. Make sure you have everything necessary for correct installation. It is the personal responsibility and obligation of the customer to contact a qualified installer to assure that electrical installation meets all national and local codes and ordinances.

Tools n e ed e d:

Gather the required tools and parts before starting installation.

Level Phillips no. 2 screwdriver Tape measure Flat-head screwdriver Pliers ⁵⁄₁₆" Box-end wrench Scissors Utility knife

IMPORTANT:

■ Do not grasp control panel to move compactor.

■ To avoid damaging floor covering, slide compactor onto

cardboard or hardboard before moving compactor across floor.

■ Do not allow the rear frame of the compactor to touch the

floor covering when lifting or moving compactor.

Undercounter Installation

2. Use pliers to lower leveling legs away from cabinet. Adjust

legs so there will be a ¹⁄₈" (3 mm) to ¹₄" (6.4 mm) space between the top of the compactor and the top of the cabinet opening. Stand the compactor upright.

3. Move the compactor close to its final location.

4. Plug into a grounded 3 prong outlet.

5. Determine if you want the compactor frame or drawer front

flush with the cabinet front. Using the two #8-18 x ⁵₁₆" (8 mm) screws, install the retaining

brackets to cabinet top as needed:

■ If the compactor frame is to be flush with the cabinet

front, place retaining bracket screws through “1.”

■ If the compactor drawer front is to be flush with the

cabinet front, place retaining bracket screws through “3.”

■ If the compactor is to be midway between “1” and “3,”

place the retaining bracket screws through “2.”

A B

1. Measure the height of your cabinet opening. The top of the

compactor should be at least

¹₈" (3 mm) from the top of the

cabinet opening. The rear wheels are preset for a cabinet opening of 34¹⁄₄"

(87 cm). See Position “1” in picture following. To adjust for other cabinet opening heights:

■ Loosen self-tapping screw just enough to clear stud from

hole in Position “1.”

■ Move the rear wheel and stud to Position “2” or “3” as

needed for your cabinet opening measurement: Position “2”: 34¹⁄₄" to 34⁷⁄₁₆" (87 to 87.5 cm) Position “3”: 34⁷⁄₁₆" to 34⁵⁄₈" (87.5 to 88 cm) NOTE: To level the compactor in position “3,” you may need to add shims under the leveling legs.

■ Tighten screw. Repeat for other rear wheel.

1 2 3

A. Wheel bracket assembly B. Cabinet C. Locating stud D. Self-tapping screw (pivot)

A. Countertop B. Retaining bracket

6. Slowly lift the front slightly and roll compactor into the cabinet

opening. Using the two #8-18 x ¹₂" (12 mm) screws, fasten the

retaining brackets to the countertop with the mounting screws.

Countertop Mounting

A. Countertop B. Retaining bracket C. Mounting screw

If brackets cannot be attached to the underside of countertop, attach mounting clips to brackets. Fasten compactor to cabinet front with mounting screws through mounting clips.

Cabinet-front mounting

Changing the Decorative Panel

There are three options for changing the decorative panel:

■ Order an acrylic panel

■ Create a custom panel for use with a trim kit

■ Create a custom panel for installation without trim

To order an acrylic panel or a trim kit, see the “Assistance or Service” section for information or call the toll-free number on the cover.

Trim Kit Panel Dimensions

A. Mounting clip B. Cabinet C. Retaining bracket D. Mounting screw

7. Grasp sides of compactor drawer and place bottom of

drawer into tracks. Lift at the handle so drawer will go over drawer stops. Close drawer. Check that the drawer opens freely. If the toe plate rubs against floor, see “Adjusting the Toe P l a te” for further instructions.

Adjusting the Toe Plate

If the toe plate rubs the floor covering, the toe plate clearance may be changed as follows:

1. Mark on each side of the toe plate the amount of toe plate

that rubs the floor covering.

2. Remove the drawer from the compactor. (See Step 3 in the

“Unpacking” section.)

3. Use a ruler and a pencil or chalk to draw a line between the

marks on each side of toe plate.

4. Use scissors or utility knife to cut toe plate along line.

5. Replace drawer. If toe plate still rubs floor covering, repeat

steps 1-4.

Air Freshener

The solid air freshener system is designed to help control odors that might develop in the trash. An air freshener disc can be purchased in department stores (not sold with compactor). Place the disk-shaped solid air freshener into the air freshener compartment. The air freshener should last 4 to 6 weeks. It is used more rapidly when the temperature is high or the air is very dry.

Use these dimension drawings to create a custom panel for use with a trim kit.

Flat Panel:

A ⁷⁄₃₂" (5.6 mm) thick panel is required. This is the same thickness as a standard ¹⁄₄" (6,4 mm) plywood or paneling.

23¹³⁄₁₆"

(

)

60.5 cm

14⁵⁄₈"

(37.2 cm)

Raised Panel:

The outer section of panel must be ⁷⁄₃₂" (5.6 mm) thick to fit into the trim. Use the dimensions shown when designing raised panel sections.

⁵⁄₈"

⁷⁄₃₂"

(5.6 mm)

(37.2 mm)

1¹⁄₄"

(32 mm)

¹³⁄₁₆

(60.5 cm)

⁵⁄₁₆"

(8 mm)

both sides

A. Raised panel or decorative trim B. Outer section of panel

⁵⁄₁₆"

(8 mm)

Trimless Panel with Handle

Dimensions

Use these dimensions drawings to create a custom panel for use without a trim kit. The panel should be ¹⁄₂" to ⁵⁄₈" (13 mm to 16 mm) thick.

NOTE: A thicker panel may need rounded front corners and a cutout for access to the handle.

23¹³⁄₁₆"

(60.5 mm)

6. Reinstall the toe guard using the existing screws and

¹⁄₂" (13 mm) washer. Then, reinstall the foot pedal.

15"

(38.1 mm)

Installation

1. Remove the mounting screws attaching the foot pedal to the

compactor. Remove foot pedal.

A. Mounting screws B. Foot pedal

2. Remove mounting screws attaching the toe guard to the

compactor. Remove toe guard.

3. Remove the mounting screws attaching the decorative panel

to the compactor. Remove decorative panel and discard mounting screws.

4. Align the bottom of the custom panel with the bottom of the

drawer front.

5. Secure the panel from the back using four #8 x 1" wood

screws as shown.

E F

A. Handle B. Custom panel C. Panel screw locations D. Toe guard E. Washer

F. To e gu ar d scr e w

Trimless Panel without Handle

Dimensions

Use these dimension drawings to create a custom panel for use without a trim kit. The panel should be ¹⁄₂" (13 mm) min. thick.

25"

(63.5 cm)

15"

(

)

38.1 cm

Installation

1. Remove the mounting screws attaching the foot pedal to the

compactor. Remove foot pedal.

7. Reinstall the toe guard using the existing screws and ¹⁄₂"

(13 mm) washer. Then, reinstall the foot pedal.

A. Mounting screws B. Foot pedal

2. Remove mounting screws attaching the toe guard to the

compactor. Remove toe guard.

3. Remove the mounting screws attaching the decorative panel

to the compactor. Remove decorative panel and discard mounting screws.

4. Align the bottom of the custom panel with the bottom of the

drawer front.

5. Secure the panel from the back using 4 – #8 x 1" wood

screws as shown.

6. Attach a 15"(38,1 cm) x ¹⁄₂" (13 mm) quarter-round filler along

the top of the drawer front using glue or screws.

A. Custom panel B. 15" (38,1 cm) x

(13 mm) quarter-round C. Panel screw locations D. Toe guard

E. Washer F. Toe guard screw

¹⁄₂

COMPACTOR USE

How Your Compactor Works

The compacting ram is the part of the compactor which compresses the trash. The compacting ram does not go to the bottom of the drawer. You will not see compacting of trash the first few times you load the compactor.

NOTE: The compactor drawer should be more than ¹⁄₂ full before the compactor can begin to compress the load.

You may hear a noise when glass breaks. Strong glass bottles may not break at all. The trash in a full compactor bag will be about ¹⁄₄ the size of its original bulk.

Load bulky trash, bottles, and cans in the center of the drawer. Bottles or cans not placed in the center may become caught between the ram and the drawer. The Drawer Monitor Switch then senses a “misload” and causes the ram to return to the “up” position without compacting.

+ 19 hidden pages